BRAYER BR4860 (01) PDF DOCUMENT

The BRAYER BR4860 fan heater consists of the following parts:

1. Carrying handle

2. Glass panel

3. Burning flame effect

4. Hot air outlet grid

5. Mode selection knob

6. Body

7. Air intake grid

8. Thermostat control knob

No, the BRAYER BR4860 fan heater is intended for use as an additional heating unit, designed to warm a small room or a specific area within a household space. It is not intended to serve as the primary source of heat.

For additional protection, it is recommended to install a residual current device (RCD) with a rated tripping current not exceeding 30 mA in the power circuit. You should contact a qualified electrician to install the RCD.

Before using the BRAYER BR4860 fan heater, carefully study the User Manual and keep it for future reference.

• Use the unit for its intended purpose only, as specified in the manual.

• Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.

• Make sure that the operating voltage of the unit indicated on the label matches your home mains voltage.

• Protect the unit from impacts, drops, vibrations and other mechanical stress.

• Do not connect the BRAYER BR4860 to any external timers or remotely controlled electrical outlets.

• The fan heater is equipped with a three-prong power cord, including a grounding conductor, and the plug is fitted with a grounding contact. The plug must be connected to a grounded outlet to reduce the risk of electric shock in case of an inner short circuit.

• To avoid fire, do not use adapters for connecting the unit to the mains.

• To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.

• If you use an extension cord, make sure that the wire gauge of both the fan heater’s power cord and the extension cord match.

• Place the BRAYER BR4860 fan heater vertically on a flat, dry, moisture- and heat-resistant surface. Do not place it horizontally and do not turn it over.

• Do not place the fan heater on soft surfaces, such as carpets with high pile, sofas, or beds.

• Ensure the distance between the front air outlet grid and any surrounding objects is at least 1 meter.

• Do not use the fan heater in confined spaces, such as built-in cabinets or recessed wall areas.

• Do not use the unit in the immediate vicinity of heating appliances, heat sources, or open flame.

• Do not use the unit outdoors, in bathrooms, or in places with high humidity.

• Do not use the unit near kitchen sinks, swimming pools, or any containers filled with water.

• Do not use the unit in places where inflammable liquids are used or aerosols are sprayed, or where such liquids are stored.

• Do not use the power cord as a carrying handle for the fan heater.

• Do not wind the power cord around the fan heater body.

• Make sure that the power cord does not come into contact with hot surfaces or sharp furniture edges.

• From time to time, check the power cord’s integrity.

• If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service, or similar qualified personnel to avoid danger.

If the unit falls into water, immediately unplug it from the power outlet before attempting to remove it from the water. Contact an authorized service center for inspection or repair. Do not immerse the unit into water or any other liquids.

• Do not touch the unit body, the power cord, or the power plug with wet hands.

• Avoid using the unit during thunderstorms.

• Avoid blocking the air inlet grid with foreign objects. Do not cover the unit during operation.

• Do not cover the hot air outlet grid, and do not insert foreign objects into the grid openings.

• During operation, the fan heater grid becomes very hot; avoid contact to prevent burns. Beware of burns from hot air.

• Never leave the unit connected to the mains unattended.

• Unplug the unit after usage and before cleaning. When unplugging, hold the power plug and carefully remove it from the mains socket; do not pull on the cord.

• If water droplets get on the fan heater body, switch it off and disconnect the power plug from the mains before touching the unit, then wipe the fan heater body with a dry cloth.

• If a foreign smell or noise appears, stop using the unit immediately.

Yes, please follow these safety instructions:

• Do not allow children to play with plastic bags or wrapping film. There is a choking hazard.

• The BRAYER BR4860 is not intended for use by children. Do not leave children unattended to prevent using the unit as a toy.

• Do not allow children to touch the operating surface, the unit body, the power cord, or the power plug during operation.

• Close supervision is necessary when children or people with disabilities are near the operating unit.

• During unit operation and breaks between operation cycles, place the unit out of reach of children.

• The unit is not intended to be used by people with physical, sensory, or mental disabilities (including children) or by persons lacking experience or knowledge if they are not under the supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.

• For child safety reasons, do not leave plastic bags used for packaging unattended.

After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.

• Unpack the unit and remove all the packaging materials.

• Keep the original package.

• Read the safety measures and operating recommendations.

• Check the delivery set.

• Examine the unit for damages; in case of damage, do not plug it into the mains.

• Make sure that the specified power supply voltage of the unit corresponds to the specifications of your mains.

• Wipe the fan heater body with a slightly damp cloth and then wipe it dry.

1. Place the fan heater base on a flat, dry, and steady surface. Do not place it on soft surfaces like carpets, sofas, or beds.

2. Make sure the distance between the front air outlet grid and any surrounding objects is at least 1 meter.

3. To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.

4. Insert the power plug into the mains socket.

5. Set the mode selection knob (5) to the desired setting:

• «О» – Fan heater is off.

• «(flame icon)» – Burning flame effect only.

• «I» – Low power heat setting for small rooms + burning flame effect.

• «II» – High power heat setting for large rooms + burning flame effect.

6. When operating in heat mode («I» or «II»), turn the thermostat control knob (8) toward the «max» position. Once the room reaches the desired temperature, turn the thermostat knob (8) toward the «min» position.

The fan heater will not switch on if the thermostat setting is close to the ambient room temperature. In this case, rotate the thermostat knob (8) toward the «max» position. If the fan heater still does not switch on, it may be caused by another malfunction. In this case, apply to a service center for repairing the fan heater.

When you switch the BRAYER BR4860 on for the first time, some smoke or foreign odor may appear. This is normal and not covered by warranty.

Yes, the BRAYER BR4860 has an automatic emergency switch-off function if the outgoing air is too hot. If the outgoing air temperature exceeds the acceptable value, the automatic thermal switch will activate, and the fan heater will be switched off.

To reset it:

1. Set the operation mode switch (5) to the «О» (off) position and unplug the unit.

2. Let the fan heater cool down for approximately 15-25 minutes.

3. Ensure that the front (4) and rear (7) air grids are not blocked with foreign objects.

4. Insert the power plug into the mains socket and switch the fan heater on again.

If the fan heater still does not switch on, it may be caused by another malfunction and you should contact a service center.

• Before cleaning the BRAYER BR4860 fan heater, set the operation mode switch (5) to the «О» (off) position and ensure the power plug is not inserted into the mains socket.

• Wipe the fan heater body (6) with a slightly damp cloth and then wipe it dry.

• Do not use liquid detergents, abrasive cleaners, or any solvents to clean the fan heater.

• To avoid the risk of electric shock, ensure that no water or other liquid gets into the fan heater body.

• To clean the air grids (4 and 7), use a vacuum cleaner with a corresponding attachment.

• After cleaning, put the BRAYER BR4860 fan heater away for storage in a dry, cool place away from children and disabled persons.

• Before using the fan heater next time, it is recommended to check the unit’s operability and the integrity of the power cord insulation and the power cord plug.

The delivery set includes:

1. Fan heater – 1 pc.

2. Instruction manual – 1 pc.

• Power supply: 220-240 V, ~ 50Hz

• Rated input power: «I» – 900 W, «II» – 1500 W

• Heating area: 15 m²

To prevent possible damage to the environment or harm to health from uncontrolled waste disposal, after the expiration of the service life of the BRAYER BR4860 or its batteries (if included), do not discard them with usual household waste. Take the unit and the batteries to specialized stations for further recycling. The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner. For further information about recycling, apply to a local municipal administration, a household waste disposal service, or the shop where you purchased this product.