BRAUN 5070CC (01) PDF Document

Please observe the following safety warnings when using your BRAUN 5070CC:

Appliance & Power Supply:

• Your appliance is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock.

• Only use the special cord set provided with your appliance.

• If the appliance is marked 492, you can use it with any Braun power supply coded 492-XXXX.

• Do not shave with a damaged foil or cord.

• The shaver is suitable for cleaning under running tab water. Detach the shaver from the power supply before cleaning it in water.

Usage:

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the safe use of the appliance and understand the hazards involved.

• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised.

Clean&Charge Station:

• To prevent the cleaning fluid from leaking, ensure that the Clean&Charge Station is placed on a flat surface.

• When a cleaning cartridge is installed, do not tip, move suddenly or transport the station in any way as cleaning fluid might spill out of the cartridge.

• Do not place the station inside a mirror cabinet, nor place it on a polished or lacquered surface.

• The cleaning cartridge contains a highly flammable liquid so keep it away from sources of ignition. Do not expose to direct sunlight and cigarette smoking nor store it over a radiator.

• Do not refill the cartridge and use only original Braun refill cartridges.

Prior to first use, remove the protection foil if any from the shaver display. Connect the shaver to an electrical outlet using the special cord set (10). When the shaver is connected to an electrical outlet, it may take some minutes until the display illuminates.

Charging and basic operating information:

• A full charge provides up to 45 minutes of cordless shaving time. This may vary according to your beard growth and environmental temperature.

• Recommended ambient temperature for charging is 5 °C to 35 °C. The battery may not charge properly or at all under extreme low or high temperatures.

• Recommended ambient temperature for shaving is 15 °C to 35 °C.

• Do not expose the appliance to temperatures higher than 50 °C for extended periods of time.

The shaver display (5) shows the status of the battery and other functions:

Charge status:

• During charging: The battery symbol will blink. (5090cc: The respective battery segment will blink.)

• Fully charged (shaver is connected to an electrical outlet): The battery symbol will light up for a few seconds. (5090cc: All battery symbols will light up for a few seconds.)

Low charge:

• The low-charge light flashes red when the battery is running low. You should be able to finish your shave. When switching off the shaver, a beep sound reminds of the low charge status.

Cleaning status:

• The cleaning indicator ▲ lights up when the shaver needs to be cleaned in the Clean&Charge Station.

Travel lock:

• The lock symbol lights up when the shaver has been locked to avoid unintended starting of the motor (e.g. for storing it in a suitcase).

For best results, Braun recommends you follow these 3 simple steps:

1. Always shave before washing your face.

2. At all times, hold the shaver at the right angle (90°) to your skin.

3. Stretch your skin and shave against the direction of your beard growth.

To shave hard-to-reach areas (e.g. under the nose), slide the MultiHeadLock switch (3) down to lock the shaver head. The shaver head can be locked in five positions.

To change position, move the shaver head with your thumb and forefinger back or forth. It will automatically click into the next position.

To set it back into the pivoting position, the MultiHeadLock switch needs to be slid up again.

Note: For automatic cleaning in the Clean&Charge Station the head lock should be released.

The travel lock prevents the shaver from starting accidentally, for example when stored in a suitcase.

• Activation: By pressing the on/off switch (4) for 3 seconds the shaver is locked. This is confirmed by a beep sound and the lock symbol in the display. Afterwards the display turns off.

• Deactivation: By pressing the on/off switch for 3 seconds the shaver is unlocked again.

Cleaning with Water:

• Switch the shaver on (cordless) and rinse the shaver head under hot running water until all residues have been removed. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.

• Next, switch off the shaver, press the release button (2) to remove the Foil & Cutter cassette (1) and let it dry.

• If you regularly clean the shaver under water, then once a week apply a drop of light machine oil on top of the Foil & Cutter cassette.

Cleaning with a Brush:

• Switch off the shaver. Remove the Foil & Cutter cassette (1) and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. Do not clean the cassette with the brush as this may damage it!

Follow these steps to install the Clean&Charge Station:

1. Remove the protection foil from the Clean&Charge Station display.

2. Using the special cord set (10), connect the station power socket (12) to an electrical outlet.

3. Press the lift button (13) at the rear side of the Clean&Charge Station to lift up the housing.

4. Hold the cleaning cartridge (17) down on a flat, stable surface (e.g. table).

5. Carefully remove the lid from the cartridge.

6. Slide the cartridge from the rear side into the base of the station until it snaps into place.

7. Slowly close the housing by pushing it down until it locks.

Charging:

Insert the shaver head down into the cleaning station. Important: The shaver needs to be dry and free from any foam or soap residue! The contacts (7) on the back of the shaver need to align with the contacts (14) in the station. Push the shaver in the correct position. A beep sound confirms that the shaver sits properly in the station. Charging will start automatically.

Cleaning:

When the cleaning indicator ▲ lights up in the shaver display, insert the shaver into the Clean&Charge Station, upside down and with the front showing (with released head lock/contact alignment/beep sound). The Clean&Charge Station analyzes the hygiene status, and the status is shown by the cleaning program indicators.

Start the cleaning process by pressing the start button (16). If the status light (15a) does not shine (the station switches to stand-by after about 10 minutes), press the start button twice. Otherwise, cleaning will not start. For best shaving results, cleaning after each shave is recommended.

The 5070cc model has one standard cleaning program. Each cleaning program consists of several cycles, where cleaning fluid is flushed through the shaver head. The cleaning time takes up to 3 minutes. During this time the status light blinks. Leave the shaver in the station for drying, which may take several hours.

After completing the cleaning and charging procedure, all indicators turn off.

When to Replace:

• When the level indicator lights up permanently red, the remaining fluid in the cartridge is sufficient for about 3 more cycles.

• When the level indicator blinks red, the cartridge needs to be replaced (about every 4 weeks when used daily).

• Each cartridge, if not used daily, should be replaced after approximately 8 weeks to ensure optimal disinfection.

How to Replace:

1. After having pressed the lift button (13) to open the housing, wait for a few seconds before removing the used cartridge to avoid any dripping.

2. Before discarding the used cartridge, make sure to close the openings using the lid of the new cartridge, since the used cartridge will contain contaminated cleaning solution.

The hygienic cleaning cartridge contains ethanol or isopropanol, which once opened will naturally evaporate slowly into the surrounding air.