BOSS WAZA CRAFT DIMENSION C DC-2W (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD BOSS WAZA CRAFT DIMENSION C DC-2W (01) PDF MANUAL


PDF Content Summary: Owner’s Manual English Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). After reading, keep the document(s) where it will be available for immediate reference. * 5 1 0 0 0 6 3 5 7 1 - 0 2 * Main Features 5 This is a WAZA CRAFT series effect pedal crafted with a high-quality analog original circuit design. 5 The “Dimension” effect add unique natural spaciousness and rich depth to your sound. 5 This pedal also reproduces the sound of “SDD-320 Dimension D” used by countless recording studios, providing a more sparkling sound. Panel Descriptions DC IN jack CHECK indicator In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC adaptor (BOSS PSA series; This indicator shows whether the effect is ON/OFF, and also doubles as the battery check sold separately). indicator. The indicator lights when the effect is ON. * Use only the specified AC adaptor (PSA series; sold separately), and connect it to an AC outlet * The brightness of the CHECK indicator (LED) will dim as the battery lowers. Replace of the correct voltage. the battery when the LED is dim or does not light. For instructions, refer to “Changing * If the AC adaptor is connected while a battery is installed, the the Battery.” power supply is drawn from the AC adaptor. * The CHECK indicator shows whether the effect is being applied or not. It does not indicate whether the power to the device is on or not. Pedal switch This switch turns the effect on/off. OUTPUT Jacks Mono output * CMSIS-RTOS RTX Version 4.70.1 Copyright (c) 1999-2009 KEIL, 2009-2015 ARM Germany GmbH Effect sound All rights reserved. Redistribution and use in source and binary forms, with Stereo output or without modification, are permitted provided that the following conditions are met: 5 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 5 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials Effect sound (L) Effect sound (R) provided with the distribution. MEMO 5 Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from The audio output of this unit does not support mono mix this software without specific prior written permission. (stereo input / mono output). To obtain the optimal Dimension effect, we recommend that you use the unit with stereo output. AC Adaptor (PSA series; sold separately) MODE SELECTOR [1]–[4] buttons S/SDD-320 switch Select the sound. Higher numbers produce a deeper effect. Switches the sound variation. By pressing two buttons simultaneously you can combine the effects. Reproduces the sound of the original DC-2. S (Standard) OUTPUT A (MONO) jack Outputs the effect sound in mono. Reproduces a sparkling sound of the SDD-320. SDD-320 Electric Guitar INPUT jack Connect the output of your Guitar Amplifier electric guitar, electronic musical instrument, or effect unit to this jack. * The INPUT A (MONO) jack doubles as the power OUTPUT B jack switch. Power to the unit is turned on when you Use this jack for stereo output. By using this in conjunction with the OUTPUT A (MONO) jack you can obtain Electronic Musical Instrument (e.g., keyboards) spacious sound. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED Precautions When Connecting WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL * To prevent malfunction and equipment failure, always turn COPYRIGHT HOLDERS AND CONTRIBUTORS BE LIABLE FOR down the volume, and turn off all the units before making any ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR connections. CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, * Once everything is properly connected, be sure to follow PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF the procedure below to turn on their power. If you turn on USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER equipment in the wrong order, you risk causing malfunction or CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN equipment failure. CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE When powering up: Turn on the power to your guitar amp last. OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS When powering down: Turn off the power to your guitar amp first. SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH * Before turning the unit on/off, always be sure to turn the DAMAGE. volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction. Use of Battery * The life of the included battery may be limited as its primary purpose was for testing during assembly. * If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). * When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible. * Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage. plug into the INPUT A (MONO) jack; the power is turned off when the Thumbscrew When this screw is loosened, the Guitar Amplifier pedal will open, allowing you to change the battery. cable is unplugged. To prevent unnecessary battery consumption, be sure to disconnect the * For instructions on changing the battery, refer to “Changing the Battery.” plug from the INPUT A (MONO) jack when not using the effects unit. Changing the Battery 1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward. * The pedal can be opened without detaching the thumbscrew completely. 2. Remove the old battery from the battery housing, and remove the snap cord connected to it. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery’s polarity (+ versus -). 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. 5. Finally, hold down the pedal while tightening the thumbscrew into the guide bush hole. Specifications BOSS DC-2W: Dimension C Nominal Input Level -20 dBu Input Impedance 2.2 MΩ Nominal Output Level -20 dBu Output Impedance 1 kΩ Recommended Load Impedance 10 kΩ or greater Power Supply DC 9 V: Alkaline battery (9 V, 6LR61), AC adaptor (sold separately) Current Draw For the USA SUPPLIER’S DECLARATION OF CONFORMITY Compliance Information Statement Model Name : Type of Equipment : Responsible Party : * If operating this unit on battery, please use alkaline battery. Address : Telephone : © 2018 Roland Corporation Intellectual Property Right Thumbscrew Pedal * This document explains the specifications of the product at the time that the document was issued. For the latest information, Spring Base refer to the Roland website. Battery Snap Cord * Roland, BOSS, and WAZA CRAFT are either registered Coil Spring trademarks or trademarks of Roland Corporation in the United Guide Bush States and/or other countries. Hole Battery Snap Battery Housing 9 V Battery 65 mA * Expected battery life under continuous use: Alkaline battery: Approx. 6 hours These figures will vary depending on the actual conditions of use. Dimensions 73 (W) x 129 (D) x 59 (H) mm 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches Weight (including battery) 450 g 1 lb Accessories Owner’s Manual, Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”), Alkaline battery (9 V, 6LR61) Option (sold separately) AC adaptor (PSA series) * 0 dBu = 0.775 Vrms DC-2W Guitar E ects Roland Corporation U.S. 5100 S. Eastern Avenue Los Angeles, CA 90040-2938 (323) 890-3700


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply