BOSCH UNIVERSAL AQUATAK 130 (01) PDF Document

Never direct the water jet at people, animals, the BOSCH UNIVERSAL AQUATAK 130 unit or electric components.

High pressure jets can be dangerous if subject to misuse.

According to the applicable regulations, the BOSCH UNIVERSAL AQUATAK 130 appliance must never be used on the drinking water network without a system separator. Use a separator as per IEC 61770 Type BA.

Water flowing though a system separator is considered not drinkable.

It is recommended that this equipment is only connected into a socket which is protected by a circuit-breaker that would be actuated by a 30 mA residual current.

The electric supply installation should comply with IEC 60364-1.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Never touch the mains plug with wet hands.

Do not pull plug while operating the device.

Do not run over, crush or pull the power supply cord or extension cord, otherwise it may be damaged. Protect the cable from heat, oil and sharp edges.

If the plug is damaged, pay attention to the following:

Plugs and sockets situated near the work site or outdoors should be to class IP 55 of BS 5490 to provide adequate protection against ingress of water, etc. and cable entries require effective sealing. Rubber shrouds should be provided over cable glands. Drip-proof (class IP X2 of BS 5490) plugs and sockets to BS 4343 are suitable for use indoors where the plug is away from the water spray area where the appliance is in use.

Warning: Inadequate extension cords can be dangerous.

If an extension cord is used, the plug and socket must be of watertight construction. The extension cord must have a cross section in accordance with the operating instructions and be protected against splashed water. The connection must not be in water.

When replacing plugs on the power supply cable or extension lead the spray water guard and mechanical stability must remain intact.

Comply with the regulations of your water supply company.

All connecting hoses must have properly sealed joints.

Make sure that the supply hose is at least 12.7 mm (1/2″) in diameter and is reinforced.

The appliance should never be used on the drinking water supply without a back flow valve. Water which has passed the back flow valve is regarded as undrinkable.

The high-pressure hose must not be damaged (danger of bursting). A damaged high-pressure hose must be replaced immediately. Only use hoses and connections recommended by the manufacturer.

High-pressure hoses, fittings and couplings are important for the safety of the appliance. Use only hoses, fittings and couplings recommended by the manufacturer.

Only clean or filtered water should be used for intake.

Before use, check that the unit and operating equipment are in perfect condition and are safe to operate. Do not use the unit if it is not in perfect condition.

Do not direct the jet against yourself or others in order to clean clothes or footwear.

Do not use solvent-containing liquids, undiluted acids, acetone or solvents! This includes petrol, paint thinners, heating oil. The sprayed vapour is highly flammable, explosive and toxic.

The gun trigger must not be jammed in position “ON” during operation.

Never use a roto nozzle or pencil jet to clean motor vehicles.

The appropriate safety regulations must be observed when using the unit in dangerous areas (e. g. petrol stations). It is forbidden to operate the unit in potentially explosive locations.

The unit must be placed on a solid base.

Take care if using the machine in a confined space ensuring that there is adequate ventilation. Ensure that all vehicles are switched off at all times whilst cleaning.

Operation of this machine requires both hands to be used at all times. Do not operate from a ladder. Take care when using the machine on balconies or other raised areas ensuring that you can see any edges at all times.

Only use detergents recommended by the manufacturer. Comply with the application, disposal and warning instructions of the detergent manufacturers.

All current-conducting components in the working area must be protected against splashed water.

Wear suitable protective clothing to protect against splash water. Do not use the machine in reach of persons, unless these are also wearing protective clothing.

If necessary wear personal protective equipment (PPE) e. g. safety goggles, breathing protection etc to protect against water, particles and/or aerosols sprayed back from parts.

During use of high pressure cleaners, aerosols may be formed. Inhalation of aerosols can be hazardous to health.

High pressure may cause objects to rebound. If necessary wear suitable personnel protective equipment such as safety goggles.

Vehicle tyres/tyre valves may only be cleaned from a minimum distance of 30 cm in order to avoid damages by the high-pressure jet. The first indication of damage is the discolouration of the tyre. Damaged vehicle tyres/ tyre valves are dangerous to life.

Materials containing asbestos and other materials which contain substances which are hazardous to your health must not be sprayed.

Detergents must not be used undiluted. The products are safe to use as they contain no acids, alkalis or substances which are detrimental to the environment. We recommend that the detergents are kept out of the reach of children. If detergent comes into contact with the eyes, wash immediately with plenty of water and if swallowed contact a doctor immediately.

Never use the power washer without water filter, or with a contaminated or damaged water filter. Using the power washer without water filter or with a contaminated or damaged water filter shall void the warranty.

Metal parts may become hot after prolonged usage, if necessary wear protective gloves.

Avoid high pressure washing in bad weather conditions especially when there is a risk of lightning.

The operator must use the unit in accordance with the regulations. He/she must take local conditions into account and be aware of other people, especially children, when operating the unit.

The unit may only be used by authorised persons who have received training or have demonstrated their ability to operate the unit. The unit must not be operated by children or juveniles (danger of accidents due to incorrect use of the unit).

Never allow children, persons with physical, sensory or mental limitations or a lack of experience and/or knowledge and/or people unfamiliar with these instructions to use the machine. Local regulations may restrict the age of the operator.

Children should be supervised to ensure that they do not play with the machine.

The unit must never be left unsupervised while the unit is switched on.

The water jet from the high-pressure nozzle produces a recoil on the gun. You should therefore hold the gun and spray lance firmly with both hands.

Switch off the motor and secure the unit before transporting.

Switch off the unit prior to all cleaning and maintenance work and before replacing components. Pull out the mains plug if the unit is mains-operated.

Repairs may only be carried out by authorised Bosch Service Centres.

Accessories and spare parts which have been approved by Bosch must be used. Original accessories and spare parts guarantee that the unit can be operated safety and without any breakdowns.

The product is intended for cleaning areas and objects outside the house, tools, vehicles and boats, if the appropriate accessories and cleaning agents approved by Bosch are used.

Intended use is related to operation within 0°C and 40°C ambient temperature.

This product should not be used for professional use.

Possible Cause: Plug not connected. Corrective Action: Connect plug.

Possible Cause: Mains socket faulty. Corrective Action: Use another socket.

Possible Cause: Fuse faulty/ blown. Corrective Action: Replace fuse.

Possible Cause: Extension cable damaged. Corrective Action: Try without extension cable.

Possible Cause: Motor protector has activated. Corrective Action: Allow to cool for 15 minutes.

Possible Cause: Frozen. Corrective Action: Wait for pump/water supply hose/accessory to thaw.

Possible Cause: Fuse faulty/ blown. Corrective Action: Replace fuse.

Possible Cause: Motor protector has activated. Corrective Action: Allow to cool for 15 minutes.

Possible Cause: Wrong mains voltage. Corrective Action: Check that mains voltage corresponds to specifications on the model tag.

Possible Cause: Fuses incorrectly rated. Corrective Action: Change to a mains supply higher than the pressure washer amp consumption.

Possible Cause: Nozzle partly blocked. Corrective Action: Clean nozzle.

Possible Cause: Insufficient power supply. Corrective Action: Check that the voltage of the mains power supply line is the same as that on the plate.

Possible Cause: Voltage loss due to use of extension cable. Corrective Action: Check characteristics of extension cable.

Possible Cause: Appliance not used for a long period of time. Corrective Action: Contact your Bosch Service Centre.

Possible Cause: Problems with TSS (Total Stop System) device. Corrective Action: Contact your Bosch Service Centre.

Possible Cause: Air in the inlet water supply hose/pump. Corrective Action: Allow power washer to operate with spray-gun trigger actuated and water cock open, until a uniform operating pressure is achieved.

Possible Cause: Inadequate water supply. Corrective Action: Check that the water supply corresponds to specifications. The minimum specification for the water supply hose is 1/2″ or 13 mm diameter.

Possible Cause: Water filter blocked. Corrective Action: Clean water filter.

Possible Cause: Water supply hoses squeezed. Corrective Action: Straighten out kinked water supply hoses.

Possible Cause: High pressure hose too long. Corrective Action: Remove high-pressure hose extension; max. hose length 7 m.

Possible Cause: Nozzle worn. Corrective Action: Change the nozzle.

Possible Cause: Start/stop valve worn. Corrective Action: Quickly actuate trigger 5 times in a row.

Possible Cause: No water supply. Corrective Action: Connect water supply.

Possible Cause: Water filter clogged up. Corrective Action: Clean the water filter.

Possible Cause: Nozzle clogged up. Corrective Action: Clean nozzle.

Possible Cause: Pump/spray gun leaky. Corrective Action: Contact your Bosch Service Centre.

Possible Cause: Leaking pump. Corrective Action: A slight water leak is permissible; in case of excessive leak, contact Bosch Service Centre.

Possible Cause: Detergent too dense. Corrective Action: Dilute with water.

Possible Cause: Residue or restriction in cleaning agent nozzle. Corrective Action: Flush with clean water and eliminate any restriction. If the problem persists, contact your Bosch Service Centre.

Step 1: Select the fan jet setting on the 3 in 1 nozzle and remove the heavy dirt.

Step 2: Attach the foam bottle and spray on the detergent sparingly.

Step 3: Rinse off the loosened dirt and detergent using the fan jet setting on the 3 in 1 nozzle.

Note: When cleaning vertical surfaces, apply the detergent from bottom to top. When rinsing off, work from top to bottom.

The power washer is self-priming and enables water to be drawn in from containers or natural water sources. It is IMPORTANT that the water filter is in clean condition when inserting it at the water inlet, and that only clean water is drawn in.

For Open tanks/containers and natural water sources, use the Self Priming accessory kit comprising: Inlet strainer with non return valve, 3 m reinforced supply hose, and Universal coupling to the pressure washer. This enables the pressure washer to draw water up to 0.5 m above the water level in the source in approximately 15 seconds.

Fully immerse the 3 m hose into the water to displace the air in the hose. Connect the 3 m hose to the power washer and make sure that the inlet strainer remains under water.

With the spray gun removed, switch the power washer on and operate it until water flows uniformly out of the high-pressure hose. If no water is coming out of the high-pressure hose after 25 seconds, switch the power washer off and check all connections. As soon as water flows out of the high-pressure hose, switch the power washer off and connect the spray gun and spray lance to begin with the work.

It is important that hose and couplings are of good quality and are tightly connected, and that the seals are undamaged and properly inserted. Loose connections can impede the priming (drawing in).

For Water Tanks with outlet connections, if connecting to a tank with a suitable tap outlet, first connect the supply hose (not provided) to the tank outlet, open the tap to allow the water to displace all the air in the hose and then connect to the pressure washer.

Switch off the motor and secure the unit before transporting.

Wear hearing protection!