BLUESKYSEA B1M (01) PDF Document

The BLUESKYSEA B1M Motorcycle Camera has the following main features:

1. It comes with 2 (two) full HD 1080p cameras. Both the front and rear cameras record high quality video at 1080P at 30fps.

2. The camera starts recording automatically when the ignition is switched on and stops recording automatically when the ignition is switched off after a brief shutdown sequence.

3. A 135° degree wide-angle lens is equipped with 2 low light sensors (Sony IMX323 Sensor) for enhanced video quality at night.

4. The cameras are rainproof (IP67 rated). The main body is installed under the seat, so it is absolutely fine to use them on a rainy day.

5. This product is simple and easy to use. Watching videos and setting items can be done through the mobile app.

The BLUESKYSEA B1M system includes the following components that connect to the main DVR Unit:

1. Camera A

2. Camera B

3. Mic

4. WIFI LED Indicator

5. Wired Controller Button

6. Power LED Indicator

7. Power Adapter

8. GPS

The lock button on the wired controller has two main functions:

• In Preview mode and Recording mode: Long press to switch Wi-Fi On/Off.

• In recording mode: Short press to lock the current recording file.

The LED indicators on the main DVR body show the status of the device:

• Red light L1 on solid: Power on

• Blue light L2 on solid: Wi-Fi function is turned on

• Blue light L3 blinking: GPS signal reception is abnormal

• Blue light L3 on solid: GPS signal reception is normal

• Blue light L4 on solid: Video signal is normal

• Blue light L5 on solid: Camera in Recording mode

• Blue light L5 is off: Camera in Preview mode

* The unit will “Beep” an alert if there is an SD memory card or camera installation error. Please check the SD card and camera connection cable if an alert sound is heard.

The LED indicators on the wired controller show the following statuses:

• Red light on solid: Power is on

• Blue light on solid: Wi-Fi has been successfully connected

The BLUESKYSEA B1M package contains the following items:

• 1x B1M 2CH Camera DVR unit

• 1x Wired Controller

• 1x Power Adapter

• 1x USB Charger Cable

• 2x 2m connection cable

• 6x 3M tape

• 1x User manual

• 1x GPS module (optional)

• 1x Y Shaped connector power cable (optional)

To insert a card:

1. Insert one micro SD card (Class 10, 16GB or larger) into the camera and push until it locks into place.

To remove a card:

1. Press the end of the micro SD card until it clicks and releases from the slot, and then pull out the SD card.

Start recording:

The camera will start recording automatically when the ignition is switched on. The blue LED indicator light will flash while actively recording.

Stop recording:

The camera will stop recording automatically when the ignition is switched off.

Long press the Lock button on the wired controller for 3 seconds to start or stop the Wi-Fi function.

Open the Dash Cam App on your phone and press the file button. You will find your video files there for playback.

1. Remove the Micro SD card from the camera and connect it to your computer’s USB socket via a micro SD card reader.

2. Once connected, open a file browser and navigate to the SD card.

3. You will find a DCIM folder. Inside it, you will find three file folders: Movie, Photo, and EMR, where your files are stored.

The video file names provide information about the recording. For example, in a file named `190820_113337_001_F`:

• “190820_113337” indicates the date and time.

• “001” indicates the video serial number.

• “F” is for front camera video files.

• “R” is for rear camera video files.

• The “EMR” file folder contains any videos that have been locked.

Locate the “Y” cable. Connect the GPS antenna and the “power adapter” to the side of the “Y” cable that has 2 connections. Connect the end of the “Y” cable that has only 1 connection to the “power adapter” cable on the DVR. The GPS information will then be displayed in the video.

1. Search for the app “B1MCAM” on your phone, then download and install it.

2. Turn on the Wi-Fi function via the Lock button on the wired controller (the Green light will be solid).

3. Connect your phone to the wireless network named B1M-xxxxxx. The default password is 12345678.

4. Open the Dash Cam App and connect to the DVR Unit.

The camera will continuously erase the oldest video as it records a new video. However, any locked video files on the memory card will not be overwritten as they are protected.

To set the loop duration, press “video segmentation” in the app and choose 1, 3, or 5 minutes. This is the length of each video loop.

To stop loop recording, press “video segmentation” and choose OFF.

WDR: Wide Dynamic Range makes it possible to display particularly dark or bright parts of the scene clearly. Options are On/Off.

Exposure rate setting: Five available settings: -2/-1/0/1/2. Default value is 0.

Sound recording: Options are On/Off. By default, the unit records sound.

Vibration video lock sensitivity (G-sensor): Automatically locks video recordings if an impact is detected. Options are OFF/Low/Middle/High. Default is Middle. Do not choose OFF if you want to use the automatic lock feature.

Time Zoom: Twenty-five available settings from -12 to +12. Default value is +9.

Format memory card: Deletes all files, including locked files, from the memory card.

Restore factory settings: Restores the device to its original manufacturer settings.

Wifi Password set: Allows you to change the Wi-Fi password from the default of 12345678.

Version: Displays the current internal firmware version.

1. Please use the supplied power adapter and USB Power cable only.

2. Never disassemble or attempt repair of this product. Doing so may damage the DVR Unit, cause electronic shock, and void your product warranty.

3. Never short-circuit the battery.

4. Exposing the DVR Unit to open flames can cause an explosion.

5. Due to local laws and vehicle safety considerations, do not operate the device using the Dash Cam App while moving.

6. Please read the user manual carefully before operation.

1. Insert a memory card (minimum 16GB – maximum 128GB) into the DVR Unit.

2. Connect cameras A & B to the DVR Unit, being sure to match the arrows and not to force the connectors.

3. Download the Dash Cam App to your phone.

4. Use the provided USB cable to connect the DVR Unit to a power source, such as a 5V USB phone charger, power bank, or a USB port on a laptop/computer.

5. After the DVR Unit has been powered on, wait about one minute. You should then be able to connect your phone to the wireless network B1M-xxxxxx (default password is 12345678).

6. Open the Dash Cam App and verify that you can see both cameras. If you can see both, you are ready to install the DVR Unit.

The power adapter has three wires that should be connected as follows:

• Connect the Red wire to a positive 12VDC source that is always on.

• Connect the Yellow wire to a positive 12VDC source that is controlled by the ignition key (also known as the ACC port).

• Connect the Black wire to the negative source, such as the battery terminal or a ground point on the bike.

1. Locate the proper place to fix the front & rear cameras, wired controller, GPS tracker (optional), and DVR Unit. It is recommended to place the DVR unit under the seat or in a top case for touring bikes.

2. Plan the path of camera cables and the power cable before installation. Most bikes will require you to remove the fuel tank to properly run the cable for the front camera.

3. Fix and connect the front and rear cameras in the proper viewing location using your choice of 3M tape, screws, or cable ties. Note: If you plan on using 3M tape, you should properly clean the surface.

4. It is recommended the supplied power adapter be connected to a source controlled by the ignition, such as a fuse box, radio, or lights, so the system starts up and shuts down with your bike. You can connect it to your battery, but you will need to make sure to turn the unit off manually after rides to avoid draining the battery.

5. The position of the DVR Unit and camera cables should be away from high-voltage circuits like xenon lamps and ignition plugs.

Loosen the lens cap, view the screen on the DashCam App on your phone, and rotate the lens body to adjust the horizontal view angle. If necessary, you can also loosen the clip with a Cross Screwdriver to adjust the camera direction.

A beeping sound upon applying power indicates an error. Try the following solutions:

Solution 1: No MicroSD card is installed in the DVR Unit. Install an approved MicroSD card.

Solution 2: A bad MicroSD card is installed. Try using a different card.

If you cannot connect to the DVR, try these solutions:

Solution 1: Verify that you are connected to the correct wireless network (B1M-xxxxxx).

Solution 2: Close the App on your phone, connect to the wireless network, and then open the App again.

Solution 3: Power off the DVR Unit, close the App, and power off your phone. Then, power on the DVR Unit, power on your phone, connect to the wireless network (B1M-xxxxxx), and open the DashCam App.