Post questions, comments, reviews or errors in the comment box below.
Your File is Ready … Download PDF
PDF Content Summary: PowerLifter® UPRIGHT DEEP CLEANER USER’S GUIDE 1694 SERIES Safety 3 Instructions 4 Product View 4 Assembly 5-7Operations 7-8Maintenance 9 Troubleshooting 12 Warranty 10 Consumer Services 11 Replacement Parts Thanks For Buying A BISSELL PowerLifter We’re glad you purchased a BISSELL PowerLifter Deep Cleaner. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your PowerLifter is well made, and we back it with a limited one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services Department, so, should you ever have a problem, you’ll receive fast, considerate assistance. My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your PowerLifter. Thanks again, from all of us at BISSELL. Mark J. Bissell President and Chief Executive Officer 2 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: Read all instructions before using your POWERLIFTER. WARNING: To reduce the ■ risk Do of not fire, immerse. electric shock, or injury: ■ Use only on surfaces moistened by cleaning process. ■ Always connect to a properly grounded outlet. See Grounding Instructions. ■ Unplug from outlet when not in use and before conducting maintenance or troubleshooting. ■ Do not leave machine when it is plugged in. ■ Do not service machine when it is plugged in. ■ Do not use with damaged cord or plug. ■ If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized Service Center. ■ Use indoors only. ■ Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners or edges, run appliance over cord, or expose cord to heated surfaces. ■ Do not carry the appliance while in use. ■ Do not unplug by pulling on cord. Unplug by grasping the plug, not the cord. ■ Do not handle plug or appliance with wet hands. ■ Do not put any object into appliance openings, use with blocked opening, or restrict air flow. ■ Do not expose hair, loose clothing, fingers or body parts to openings or moving parts. ■ Do not pick up hot or burning objects. ■ Do not pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapor. ■ Do not use appliance in an enclosed space filled with vapors given off by oil base paint,paint thinner,some moth proofing substances,flammable dust,or other explosive or toxic vapors. ■ Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, gasoline, etc.). ■ Do not modify the 3-prong grounded plug. ■ Do not allow to be used as a toy. ■ Do not use for any purpose other than described in this User’s Guide. ■ Do not operate the appliance unless the belt door is securely assembled in the location provided. ■ Use only manufacturer’s recommended attachments. ■ Use only cleaning products formulated by BISSELL for use in this appliance. ■ Keep openings free of dust, lint, hair, etc. ■ Keep appliance on a level surface. ■ Turn off all controls before unplugging. ■ Be extra careful when cleaning stairs. ■ Close attention is necessary when used by or near children. WARNING: The Power Cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING. SAVE THESE INSTRUCTIONS. THIS MODEL IS FOR HOUSEHOLD USE ONLY. Commercial use of this unit voids the manufacturer’s warranty. GROUNDING INSTRUCTIONS This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged and codes grounded and into ordinances. an in outlet accordance that is properly with all local installed WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the drawing above. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance. Grounded Outlets Grounding Pin 3 WARNING: Product View To BISSELL Formulas ing may ranty. based be with PowerLifter reduce used. formulas the damage Chemical soil plastic Advanced These in the removers causing your that this risk products spot materials PowerLifter. contain appliance of Deep cracking should cleaners fire, may use Cleaning lemon used not and only Use or or react in pitting. or solvent- void of your pine clean- war- oil Strain Reliever HandleTM Handle Assembly Lower Body Dirtlifter® PowerBrush 4 Spray Trigger Power Switch ON OFFQuick Release Cord WrapTM Measuring Power Cord Cup Tank-in-TankTM Lower Cord Wrap Easy Rolling Wheels Handle Release Belt Access Door Floor Nozzle Window
How To Assemble Your PowerLifter assembles in two quick steps. The only tool you will need to assemble your cleaner is a Phillips head screwdriver. Your PowerLifter is packaged as two primary components... the Lower Body and the Handle Assembly. To assemble: 1.Slide the Handle Assembly (with attached Quick Release Cord WrapTM) down into the Lower Body until it will go no further. Phillips Head Screw 2. Secure (supplied) the through handle the by placing screw opening one (1) Phillips in the Lower head Body screw and into the rear of the Handle Assembly. Tighten with screwdriver until secure. Assembly is now complete. Phillips Head Screw Phillips Head Screw The Power Switch controls power to the machine. The Powered Brush roll at the Floor Nozzle is designed to enhance cleaning performance. The bristle pattern lifts out the deep down dirt while gently grooming carpet fibers. The floating suspension self-adjusts to all carpet heights and protects your carpet if you leave the Power switch ON. When the machine handle is in the full upright position, CarpetSaverTM automatically raises the brush off the carpet. Your PowerLifter is equipped with a Measuring Cup for adding the proper amount of cleaning formula to the Tank-in-Tank. Before using the machine, simply fill the Measuring Cup to the fill line with BISSELL Fiber Cleansing Formula. Pour the formula into the Tank-in-Tank as shown on page 6. For convenience, the Measuring Cup stores on the back of the unit. 5 The Basics: How Your PowerLifter Works Power DirtLifter PowerBrush Measuring Cup ONOFF Power Switch Tip: Deep carpeting cleaning regularly can reduce dust and your allergens home. in WARNING: To reduce the risk of fire, electric shock or injury, unplug from outlet before servicing. OFFON
6. To Fill The Tank-in-Tank This easy-to-use system is designed with a bladder inside to hold clean water. As you clean, the bladder will empty. Dirty water collects in the tank outside the bladder. NOTE: Make sure to add formula to the tank before filling it with water. Depress the Handle Release pedal to tilt back the handle. Lift the Tank-in-TankTM handle. The handle locks the lid in place. Carry the Tank-in-TankTM like a bucket to fill at the sink. Set the Tank down and rotate the handle forward to unlatch the Lid. Lift off and set the Lid aside. Using the Measuring Cup, pour BISSELL Deep Cleaning Formula into the mouth of the bladder. Fill to the bottom of the neck with hot tap water. Do not boil or microwave water. NOTE: Fill slowly to reduce sudsing. Replace the Tank Lid, matching the Lid and Tank edges. Rotate the handle to carrying position. Replace Tank in machine base, seating firmly in place. Rotate handle back down to latched position. NOTE: Remove the Tank-in-Tank, following steps 1 and 2 at the top of the page. 1.Carry the Tank-in-Tank, like a bucket, to the sink. Remove Tank Lid. Pour out dirty water. 2.After on the each Tank use, Lid. remove and rinse the Lint Screen located A. Remove Tank Lid. B. Remove Lint Screen and rinse under faucet. Remove any debris caught in Lint Screen. C. Re-insert Lint Screen on Tank Lid. The screen will click into place. D. Replace Tank Lid. 3. Refill steps with cleaning solution and clean tap water—follow 3-5 above. When a cleaning job is complete, rinse out the Tank-in-Tank by running clean water between the bladder and the tank. Return the Tank-in-Tank to the machine, follow step 6 above. Refer to the Maintenance/Storage section on the next page for final cleanup. Handle Release 1.2.3Rotate to Unlatch Handle 126.96.36.199 4 6.When It’s time To Empty The Tank-in-Tank 1 Lint Screen 2B 2C Lint Screen 5 Latched 4.5.6. Tilt Handle Back 1 2 Lift and Carry 4 Tip: A special red float device in the tank will cause the cleaner to stop removing solution from the carpet. The motor sound will rise in pitch to let you know the dirty water tank is full.
Normal Cleaning 1.Plug the PowerLifter into a proper outlet and turn ON the Power Switch. 2.Make ing the one SprayTrigger. slow forward Caution: and backward Do not overwet. wet pass by push- 3.Release back pass the over Spray the Trigger same area and make to remove one slow any residual forward dirty and water. 4.Repeat until you cleaning can’t see passes any more without water pressing being the Spray Trigger suctioned up. 5. When cleaning job is complete, refer to Maintenance/Storage. Maintenance/Storage 1.Turn Power Switch OFF. 2.Unplug Power Cord Power Quick Cord Release. from outlet and coil cord around 3.Remove Tank-in-Tank. Dispose of dirty water. 4.Rinse onto the out machine. Tank-in-Tank and re-seat the tank 5.Wipe all exterior surfaces with a soft cloth. 6.Store cleaner in a protected, dry area. 7.When that the carpet PowerLifter is dry, vacuum may have again loosened. to remove hair and fuzz Pump Belt Replacement NOTE: Turn off machine and unplug from wall outlet. To Remove Broken Pump Belt 1.Step (see illustration). on Handle Release pedal and recline Handle on floor 2.Remove the Tank-in-Tank. Set aside (see illustration). 1 WARNING: To fire, injury, outlet reduce electric before unplug the shock servicing. risk from of or Power Quick Release Cord 2 OFFON CAUTION: PowerLifter water be there freezing. will components the stored warranty. damage is and a Freezing where danger must uses internal and not void of 7. 8 3.4.5. Remove the Belt Access Door. Insert a flathead screwdriver into the slot nearest the handle to gently pry off the door (see illustration). Turn the machine onto its side so the belt access area is facing upward (see illustrations). On the bottom of the machine, near the belt access area, is a Red Retainer Plate that holds the black Brush Arm and brush in place. Using a Phillips head screwdriver remove the screw that holds the Red Retainer Plate in place. Set Red Retainer Plate and Phillips head screw aside (see illustrations). 3. 4. 3. 4. 5. 6. 188.8.131.52.184.108.40.206.6.7.8. To Remove Broken Pump Belt Continued Remove the black Brush Arm that holds the brush in place. Set the black Brush Arm aside (see illustrations). Remove the “toothed” brush belt from the brush belt and brush aside Locate and remove the broken Pump Belt. To Install the Replacement Pump Belt With the unit still on its side, loop one end of the replacement pump belt around the red pump pulley and then the other end around the silver motor shaft (see illustration). Do not twist the replacement pump belt. Re-install the toothed brush belt first onto the red pump pulley and then onto the toothed end of the brush (see Illustration). Re-install the brush into the base of the unit. Place the black brush arm onto the brush and slide black brush arm into base of unit. The black brush arm and brush should slide easily into original position (see illustration). Re-install the red retainer plate and Phillips head screw (see illustration). Using your finger, gently spin the replacement pump belt on the silver motor shaft. If assembled correctly, the replacement pump belt should rotate freely around the silver motor shaft and drive pulley without obstruction. The brush should also rotate freely when the silver motor shaft is turned. Turn the machine right side up and replace the Tank-in-Tank, and belt access door (see illustration). Assembly is now complete. 7. 8. 7. 8. 1.2. 3. 1.2. 3. 1.2. 3. 1.2. 3. 4. 5. 4. 5. 6. 7. 6. 7.
If you have any questions, or are having trouble installing your replacement pump belt, please call BISSELL Consumer Services at 1-800-237-7691. Troubleshooting Reduced Spray Or No Spray. Possible Causes Remedies Insert Screwdriver Blade Here 1 Bladder may be empty 1 Turn power OFF, refill tank with hot tap water. 2 The lint screen may be clogged 2 Turn power OFF, clean out lint screen, follow step 2 (empty the Tank-in-Tank) on page 6. 3 Tank-in-Tank may not be seated properly 3 Turn power OFF; remove and reseat tank. 4 Pump may have lost prime 4 Turn power OFF; after 1 minute, turn ON and depress Spray trigger. 5 The Pump Belt may be broken 5 Turn power OFF and unplug machine from outlet. To check if a Pump Belt has broken, you will need a flathead screwdriver. Insert the blade end into the lower slot of the Belt Access Door to release the latch. If necessary, insert the blade end into the upper slot to release the upper latch. Examine for belt breakage. You should be able to see the Pump Belt looped around the motor shaft. If it is broken or missing, please refer to the part numbers and descriptions on page 11 before calling BISSELL Consumer Services. Complete installation instructions will accompany the replacement belt. PowerLifter is not picking up solution and water. Possible Causes Remedies 1 Nozzle Window may not be 1 Make sure the two tabs on the back of properly attached the Floor Nozzle Window are inserted through the mating slots in the main housing. Reinstall if necessary. 2 Tank-in-Tank Lid is not 2Reinstall lid; refer to page 6. properly installed 3 Tank-in-Tank is not properly seated 3 Tank-in-Tank must be firmly seated to function. Remove and reseat Tank-in-Tank. 4 Tank-in-Tank has picked up the maximum 4 Empty tank and refill; refer to page 6. amount of dirty water Thank you for selecting a BISSELL product. If you should happen to need assistance during assembly or operation, call: 1-800-237-7691 Please do not return this product to the store. WARNING: To fire, injury, outlet reduce electric before unplug the shock servicing. risk from of or Lift Here 9 10 BISSELL Consumer Services For information about repairs or replacement parts, or questions about your warranty, call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 am — 10 pm ET Saturday 9 am — 8 pm ET Or write: BISSELL Homecare, Inc. PO Box 3606 Grand Rapids MI 49501 ATTN: Consumer Services Or visit the BISSELL website - bissell.com When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________ NOTE: Please keep your original sales receipt. It is your warranty. Part Numbers And Descriptions Item Part No. Part Name 1 015-9043 Tank Assembly Complete 2 015-4439 Tank Lid Assembly 3 015-9041 Tank Bottom 4 213-0213 Baffle with Red Float 5 213-3501 Lint Screen 6 215-0628 Pump Belt 7 0710 48 oz. BISSELL Fiber Cleansing Formula with ScotchgardTM Protector 8 0720 48 oz. BISSELL Multi-Allergen Formula with ScotchgardTM Protector 9 0400 22 oz. BISSELL Tough Stain PreCleaner 1 2 3 4 5
6 7 8 9 TOUGH STAIN PRECLEANER TM Penetrates and Loosens Tough Stains & Embedded Dirt before Deep Cleaning 11
About Your Warranty This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below. Limited One Year Warranty Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part. See information below on "If your BISSELL product should require service". This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction the User's Guide caused is not by negligence, covered. abuse, neglect, unauthorized repair, or any other use not in accordance with If your BISSELL product should require service: Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area. If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Services.Website or E-mail: bissell.com Use the “Customer Services” tab. Or Call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 am. - 10 pm. ET Saturday 9 am. - 8 pm. ET Or write: BISSELL Homecare, Inc. PO Box 3606 Grand Rapids MI 49501 ATTN: Consumer Services BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. ©2004 BISSELL Homecare, Inc Grand Rapids, Michigan All rights reserved. Part Number 310-4801 Rev 2/04 12 Visit our website at: bissell.com Scotchgard ia a trademark of 3M
FREE ENGLISH PDF
USER GUIDE - USER MANUAL
OWNER GUIDE - OWNER MANUAL
REFERENCE GUIDE - REFERENCE MANUAL
INSTRUCTION GUIDE - INSTRUCTION MANUAL