BIAMP TDT50 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD BIAMP TDT50 (01) PDF MANUAL


PDF Content Summary: TDT50/TDT150 TDT100/TDT300 Transformer Installation Instructions

THESE INSTRUCTIONS COVER THE INSTALLATION OF THE FOLLOWING OUTPUT TRANSFORMERS FOR 25/70/100 VOLT SPEAKER SYSTEMS • TDT50 50watts Output Transformer for MCA8050 (Single Channel) • TDT100 100watts Output Transformer for MCA8050 (Bridge Channels) • TDT150 150watts Output Transformer for MCA8150 (Single Channel) • TDT300 300watts Output Transformer for MCA8150 (Bridge Channels) CAUTION – These servicing instructions are for use by qualified personnel only. To reduce the risk of electronic shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. NOTE – To avoid fault conditions, High Pass Filters (HPF) must be assigned on those channels having transformers installed. KIT CONTENTS: • (1) Transformer • (1) Holding nut • (2) rubber washers • (1) Metal dome washer • (1) stickers • (1) Instructions RECOMMENDED TOOLS: • Phillips screwdriver • Adjustable wrench • Pliers TDT50 & TDT150 INSTALLATION INSTRUCTIONS 1. Disconnect AC power from the amplifier. 2. Remove the amplifier top panel by removing 17 screws (6 on each side, 3 on back and 2 on front). Please note that front screws are longer. 3. If the mounting bolts have two nuts, remove one and save. These nuts will be used to hold the transformers in place. If the mounting bolts have only one nut, do not remove. Transformer will be held in place with supplied nut. 4. Install transformers as shown in figure 1. Nut Metal Dome Washer Rubber Washer Transformer Rubber Washer Transformer Rubber Washer Bolt 5. Locate the amplifier circuit boards and jumpers. Each amplifier card represents two individual output channels; one odd and one even (refer to figure 2 for reference). 6. Using a pair of pliers, remove the black and red jumper from the associated amplifier channel. 7. Following the diagram below (figure 3), connect the wires as indicated. Please note that wires on odd channel are mirrored from wires on even channel. Odd Channels (1, 3, 5, & 7) FIGURE 3 8. Replace amplifier top panel (longer screws go on the front). 9. Assign channel HPF (High Pass Filter) by flipping the appropriate channel rear panel dip switch. (figure 4) 10. Apply appropriate rear panel “xfmr” voltage sticker. (figure 5) FIGURE 1 Odd channel jumpers (Ch 1) Even channel jumpers (Ch2) Amplifier Cards Even Channels (2, 4, 6, & 8) High Pass Filter (HPF) dip switches Brown wire = 25V Orange wire = 70V Yellow wire = 100V Blue wire Blue wire Brown wire = 25V Orange wire = 70V Yellow wire = 100V Brown wire = 25V Orange wire = 70V Yellow wire = 100V

Black wire Green wire Green wire Black wire FIGURE 5 FIGURE 2 FIGURE 4 Affix transformer stickers TDT100 & TDT300 INSTALLATION INSTRUCTIONS 1. Disconnect AC power from the amplifier. 2. Remove the amplifier top panel by removing 17 screws (6 on each side, 3 on back and 2 on front). Please note that front screws are longer. 3. If the mounting bolts have two nuts, remove one and save. These nuts will be used to hold the transformers in place. If the mounting bolts have only one nut, do not remove. Transformer will be held in place with supplied nut. 4. Install transformers as shown in figure 6. 5. Locate the amplifier circuit boards and jumpers. Each amplifier card represents two individual output channels; one odd and one even (refer to figure 7 for reference). 6. Using a pair of pliers, remove the red jumper from both amplifier channels. 7. Following the diagram below (figure 8), connect the wires as indicated. Odd Channels (1, 3, 5, & 7) FIGURE 8 8. Replace amplifier top panel (longer screws go on the front). 9. Assign channel HPF (High Pass Filter) by flipping the appropriate channel rear panel dip switch. (figure 9) Bridge dip switch 10. Assign bridge mode by flipping the rear panel bridge dip switch (figure 9) 11. Apply appropriate rear panel “xfmr” voltage sticker. (figure 10) FIGURE 10 Black Brown wire = 25V wire Orange wire = 70V Yellow wire = 100V Blue wire Green wire FIGURE 6 FIGURE 7 FIGURE 9 Nut Metal Dome Washer Rubber Washer Transformer Rubber Washer BoltOdd channel jumpers (Ch 1) Even channel jumpers (Ch2) Amplifier Cards Even Channels (2, 4, 6, & 8) Affix transformer stickers High Pass Filter (HPF) dip switches DoC MCA201003 EC Declaration of Conformity Biamp Systems Corporation, as manufacturer having sole responsibility, hereby declares that the following described product complies with the applicable provisions of the DIRECTIVES below except as noted herein. Any alterations to the product not agreed upon and directed by Biamp Systems Corporation will invalidate this declaration. Product Models: MCA 8050 with optional Output Transformers TDT50 or TDT100 MCA 8150 with optional Output Transformers TDT150 or TDT300 Product Description: Audio Amplifiers and Distribution Transformers Applicable EC Directives: Applicable Harmonized Standards: LVD Directive (2006/95/EC) Safety EN 60065:2002 EMC Directive (2004/108/EC) Emissions EN 55103-1:1996, Environment E2 Immunity EN 55103-2:1996 Special Considerations for Product Environment or Compliance: Shielded cabling must be used for system connections. Technical Documentation File, Location and Contact: Biamp Systems, Inc. phone: (503) 641.7287 9300 S.W. Gemini Drive fax: (503) 626.0281 Beaverton, OR USA 97008 e-mail: biamp@biamp.com Authorized Representative: Larry Copley, Compliance Engineer Authorized Signature: Issued: March, 2010 Biamp Systems | 9300 S.W. Gemini Drive | Beaverton, OR | 97008 | USA | +1.503.641.7287 | biamp.com


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply