BIAMP CMA60 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD BIAMP CMA60 (01) PDF MANUAL


PDF Content Summary: TM CMA Series Commercial Mixer/Amplifiers Operation Manual Biamp Systems, 10074 S.W. Arctic Drive, Beaverton, Oregon 97005 U.S.A. (503) 641-7287 biamp.com an affiliate of Rauland Borg Corp. Print Update June 17, 2002

TABLE OF CONTENTS Front Panel Features Rear Panel Features Modifications Applications Specifications Block Diagram Warranty pg. 2 pg. 4 pg. 6 pg. 8 pg. 12 pg. 13 CMA Series INTRODUCTION The CMA Series of commercial mixer/amplifiers combines a versatile 6-input mic/line mixer with either 30, 60, 120, or 350 Watt amplification. Mixing functions include mic/line/telephone inputs, selectable automatic & manual channel muting, channel priority assignment, remote level control, tone control, a built-in compressor, an internal chime, phantom power, and extensive output patching. The amplifier includes an output transformer, and provides rated power into direct or distributed speaker systems. The CMA Series carries a five-year warranty. CMA Series features include: ♦ integrated mixer, power amplifier, and output transformer ♦ five electronically balanced microphone/line input channels ♦ one transformer balanced microphone/line/tel input channel ♦ rear panel trim control & pad switch on each input channel ♦ +24 Volt phantom power selectable on each input channel ♦ imput transformer option on mic/line inputs (except CMA350) ♦ automatic muting of selected channels (-10, -20, or -40dB) ♦ automatic muting triggered by selected "priority" channels ♦ manual muting of selected channels (-10, -20, or -40dB) ♦ manual muting triggered from remote contact closures ♦ remote control of master level via rear panel terminals ♦ integral output compressor with rear panel threshold control ♦ recessed treble & bass controls plus "loudness" & "low-cut" ♦ two insert points for signal processing and remote control ♦ two line-outs and one stack-in for system interconnections ♦ 30, 60, 120, or 350 Watts into direct or distributed systems ♦ front panel indicators for power, fault, signal, and peak ♦ internal 'pre-announcement' chime tone with level control ♦ input/output connections provided on barrier strip terminals ♦ integral security cover and removable rack-wing/handles ♦ covered by Biamp Systems' five-year warranty ♦ marked, UL and C-UL (UL Canada) listed

1 FRONT PANEL FEATURES CMA30, CMA60, & CMA120 Front Panels peak signal CMA120 fault

1 2 3 4 5 6 0 on master 0

off on off on off on+

low cut power loudness contour tone control + bass treble

CMA350 Front Panel CMA350 peak signal fault

1 2 3 4 5 6 0 power master 0

I off on off on off on+

low cut loudness contour tone control + bass treble O

2 FRONT PANEL FEATURES

Level (Channels 1~6): These controls adjust the amount of signal sent from the individual input channels to the mixer output. Optimum Level setting is near the 12 o'clock position (unity gain). Level (Master): This control adjusts the amount of signal sent from the mixer output to the amplifier input. The Master Level control is used to adjust the overall volume of the system. Low Cut: This switch inserts a low cut filter (6dB/octave @ 120Hz) at the amplifier input. CAUTION: To avoid output fault conditions, Low Cut must be used when driving 25/50/70/100 Volt speaker systems (see Output Selector & Output Terminals on pg. 4). Also, any other system equalization affecting frequencies below 120Hz should remain flat or be used as cut-only. This precludes the use of Loudness Contour or boosting of the Bass control (see below) in these applications. Loudness Contour: This switch inserts a loudness filter at the mixer output (+6dB @ 100Hz & +4dB @ 10kHz). The Loudness filter provides tonal compensation when operating with low-level music signals. Tone Control: This switch enables the Bass & Treble controls. Bass: This screwdriver control adjusts the low-frequencies ("Bass") at the mixer output (±10dB @ 100Hz). Treble: This screwdriver control adjusts the high-frequencies ("Treble") at the mixer output (±10dB @ 10kHz). Peak Indicator: This red LED flashes when signal levels at the amplifier output have reached maximum. Occasional flashes of the Peak Indicator are acceptable, however, a continuously lit LED may indicate an excessive level setting. Signal Indicator: This yellow LED remains lit when signal is present at the amplifier output. Fault Indicator: This red LED lights to indicate fault conditions due to overheating, DC offset voltage, or failure of low-voltage power. The Fault Indicator will light for 3-5 seconds at turn-on, and then go off if no fault is detected. Some faults (such as overheating) will correct themselves when the unit has been turned off awhile. If the Fault Indicator remains lit when the unit is turned back on, contact your local Biamp Systems dealer. On Indicator: This green LED remains lit when AC power is applied to the unit. Power Switch: This switch applies AC power to the unit.

3 REAR PANEL FEATURES CMA30, CMA60, & CMA120 Rear Panels

120watt output BIAMP SYSTEMS an affiliate of send/return channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

Rauland-Borg Corp xfmr direct chime max phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute

E158021 4 com level line min rec amp pre level -40 -20 trim nominamin level -40 -20 level -40 -20 level -40 -20 level -40 -20 level -40 -20

LISTED 2 Z 91 COMMERCIAL 8 AUDIO EQUIP R R out out in max trim nominamin max trim nominamin max trim nominamin max trim nominamin max trim nominamin out max

C 6.3A - 115V 25V compressor auto mute priority on off line priority on off line priority on off line priority on off line priority on off line priority on off line

50V out min threshold adjust max min mic mic mic mic mic mic

70V remote mute/ tel

level stacking in

3.15A -230V USE ONLY WITH 250V FUSE ~ 115/230V AC 50/60 Hz 375 VA +10V c chime + + + + + + + CMA350 Rear Panel

CMA350 send/return channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

BIAMP SYSTEMS Portland, Oregon an affiliate of Rauland-Borg Corp. chime level max min phantom pwr auto mute manual mute mute level -40 phantom pwr auto mute manual mute mute level -40 phantom pwr auto mute manual mute mute level -40 phantom pwr auto mute manual mute mute level -40 phantom pwr auto mute manual mute mute -40 phantom pwr auto mute manual mute mute level -40

line out rec out amp in pre out -20 trim nominalmin -20 trim nominalmin -20 trim nominalmin -20 trim nominalmin level -20 -20 max trim nominalmin

5 R 1 1 WARNING: E158021 LISTED 2 Z 91 COMMERCIAL AUDIO EQUIP R C max priority on off compressor auto mute max priority on off max priority on off priority on off max trim nominalmin priority on off max priority on off

do not change AC voltage switch when power is on. 350 watt output xfmr direct out min threshold adjust max min line mic line mic line mic line mic line mic line mic tel

USE ONLY WITH 6.3A - 115V 3.15A -230V 70V 50V 25V 8 com 4 mute/ chime remote level stacking in channel 6 channel 5 channel 4 channel 3 channel 2 channel 1 c

250V FUSE +10V + + + + + + + ~ 115/230V AC 50/60 Hz 700 VA

Power Entrance: This receptacle accepts a 3-prong AC power cord. WARNING: DO NOT REMOVE OR DEFEAT THE GROUND PRONG, AS THIS CONSTITUTES A SHOCK HAZARD. The removable lower portion of the receptacle holds the AC fuse. NOTE: See AC Fuse on page 7 for replacement by qualified personnel. A chassis ground post is provided (next to the receptacle) for system grounding. Power Selector Switch (model CMA350 only): This switch selects either 115 Volt or 230 Volt AC operation for model CMA350 (see Modifications on pg. 7). Power Selector Switches for other models are on the underside of the chassis. Output Selector: This switch selects either direct output or transformer coupled output from the amplifier. On models CMA60, CMA120, & CMA350 direct output is from the 4Ω terminal. On model CMA30, direct output is from the 8Ω terminal. NOTE: Model CMA350 can be used in 25V 'balanced' output applications only with an optional external transformer DT-4 (#909-0031-00) connected at the 4 ohm (direct) output. Output Terminals: These screw terminals provide connection for speaker loads (4Ω, 8Ω, 25V, 50V, 70V, or 100V) at the amplifier output (see Output Selector above). NOTE: 100V output is an export model option only. WARNING: THE LOUDSPEAKER OUTPUTS POSE A RISK OF HAZARDOUS ENERGY. LOUDSPEAKER CONNECTIONS MUST BE MADE PROPERLY. THE OUTPUT TERMINAL COVER MUST BE INSTALLED WHEN THE DEVICE IS ENERGIZED. Chime Level: This control adjusts the volume level of the chime tone (see Mute/Chime on next page). To turn the chime tone off completely, set this control to the fully counter-clockwise position. Send/Return: This 3-conductor TRS 1/4" Phone jack provides an insert point for signal processing or remote control devices. It is wired with Tip as send, Ring as return, and Sleeve as ground. Send/Return is after Stacking In, Loudness, & Tone, but before Compressor, Master Level, & Low Cut. Send/Return is a switching jack, which interrupts the signal flow only when a plug is inserted.

4 REAR PANEL FEATURES

Line Out: This RCA phono jack provides an unbalanced line-level output from the mixer. Line Out is after Stacking In, Loudness, Tone, Compressor, & Master Level, but before Low Cut. Rec Out: This RCA phono jack provides an unbalanced line-level output from the mixer. Rec Out is after Stacking In, but before Loudness, Tone, Compressor, Master Level, & Low Cut. Pre Out: This RCA phono jack provides an unbalanced line-level output from the mixer. Pre Out is after Stacking In, Loudness, & Tone, but before Compressor, Master Level, & Low Cut. Pre Out and Amp In may be used together as an insert point for signal processing or remote control devices. Remove jumper before connecting devices. To connect Pre Out to both Amp In and an external device, a parallel (‘Y’) cable must be used. Amp In: This RCA phono jack provides an unbalanced line-level input to the amplifier. Amp In is after Stacking In, Loudness, & Tone, but before Compressor, Master Level, & Low Cut. Pre Out and Amp In may be used together as an insert point for signal processing or remote control devices. Remove jumper before connecting devices. Compressor: This control adjusts the threshold level at which the internal compressor circuit is activated. The internal compressor has a fixed compression ratio of 4:1, and is used to reduce peaks in output signal level, as well as to moderate volume differences between loud and soft signals. Auto Mute: This control adjusts the threshold level at which signals from "priority" channels will automatically trigger muting of selected non-priority channels (see Assignment & Priority below). Remote Level: These two screw terminals (plus " ") provide remote volume control of the master level. An internal voltage controlled amplifier (VCA) allows remote control from up to 2000 feet away, using any 5k~50kΩ linear taper potentiometer and/or switch to provide adjustment and/or muting of the master level. Potentiometers are wired with high-side to "+10V", low-side to " ", and wiper to "C". Switches simply connect (or disconnect) "+10V" to "C", and do not require a ground (‘ ’) connection. NOTE: The factory installed jumper (between "+10V" & "C") must be in place when a remote control is not being used. Mute/Chime: This screw terminal (plus " ") allows manual muting of any selected channels, via an external switch or contact closure (see Assignment & Priority below). When the Chime Level control is turned up (on), a pre-announcement chime tone will also be activated by the switch or contact closure. Stacking In: These screw terminals provide a balanced line-level input to the mix bus, for input expansion. Stacking In is before Loudness, Tone, Compressor, Master Level, & Low Cut. For unbalanced input, wire high to (+) and ground to both (-) & ( ). Assignment: These five DIP switches are used to assign specific functions to the individual channels. To assign a function, move the respective switch to the left. Phantom Pwr assigns +24 Volts DC phantom power to the channel input, for powering condenser microphones. CAUTION: TO AVOID DAMAGE TO EQUIPMENT, ASSIGN PHANTOM POWER ONLY ON CHANNELS WHICH ARE SELECTED FOR 'MIC' INPUT AND WHICH REQUIRE PHANTOM POWER. Auto Mute assigns a (non-priority) channel to be muted whenever signal is present in any "priority" channel. Manual Mute assigns a channel to be muted whenever the Mute/Chime terminals are shorted together via a switch or contact closure. Mute Level assigns the amount of muting (-10dB, -20dB, or -40dB) which is applied to a channel, when triggered by either Auto Mute or Manual Mute. NOTE: -10dB muting will occur when both switches are to the right. -40dB muting will occur when both switches are to the left. Trim: This control adjusts the input gain of the channel, to compensate for various input signal levels. Once the Line/Mic switch has been set to the proper position (see Line/Mic below), the Trim control should be adjusted so that peaks in signal level do not cause distortion at the channel input. Priority: This switch assigns a channel to "priority". When signal is present in a "priority" channel, any (non-priority) channels which are assigned to Auto Mute will be muted by their selected amount. NOTE: A "priority" channel cannot be auto muted by another "priority" channel, but a "priority" channel can be manual muted. Line/Mic: This switch selects the proper impedance and gain for either microphone or line-level input signals. Depress the switch for line-level input. Release the switch for microphone input. On Channel 1, the Tel switch (see Tel below) must be released for the Line/Mic switch to operate. Tel (Channel 1 only): This switch selects the proper impedance and gain for input from 600 ohm sources. The input for Channel 1 includes an isolation transformer, which allows connection to most telephone system audio ports. Inputs: These screw terminals provide a balanced input connection for the channel. For unbalanced input, wire high to (+) and ground to both (-) & ( ). The input for Channel 1 includes an isolation transformer. Input isolation transformers are optional on the other channels (2~6) of all models, except for the CMA350 (Biamp #908-0040-00).

5 MODIFICATIONS CAUTION: THE FOLLOWING INFORMATION IS FOR USE BY QUALIFIED INSTALLATION/SERVICE PERSONNEL. Removable Rack-Handles: The CMA Series have removable rack-handles. To remove the rack-handles: 1) Remove the two screws from the side of each rack-handle. 2) Remove the rack-handles. 3) Replace the mounting screws in the sides of the chassis. Security Cover: The CMA Series includes a removable front panel security cover. A hole in the security cover provides access only to the power switch. To remove the security cover: 1) Using a 3mm hex wrench, loosen the two captive security cover mounting screws. 2) Remove the security cover. 6 MODIFICATIONS WARNING: TO REDUCE THE RISK OF SHOCK, DISCONNECT ALL POWER FROM THE UNIT BEFORE MAKING ANY INTERNAL MODIFICATIONS OR EXTERNAL FIELD WIRING CONNECTIONS. 115V/230V AC Operation: The CMA Series may be converted to 230V operation for use in other countries. To convert to 230V operation: 1) Remove the fuse holder compartment from the lower portion of the rear panel AC Power Cord receptacle. 2) Replace the fuse in the fuse clip with the same type and appropriate value fuse (see table below). 3) Replace the fuse holder compartment. 230V fuse values CMA30 - 1A NB 250V CMA60 - 2A NB 250V

CMA120 - 3A NB 250V CMA350 - 3.15A SB 250V USE ONLY WITH 250V FUSE

4) Select the 230V position on the Power Selector Switch. The Power Selector Switch for models CMA30, CMA60, & CMA120 is recessed into the underside of the chassis, near the AC Power Cord receptacle. The Power Selector Switch for model CMA350 is instead located on the left side of the rear panel, above the AC Power Cord receptacle. rear panel bottom panel 115V 230V AC Fuse: The AC Fuse is in the lower portion of the AC Power Cord receptacle. If the AC fuse should require replacement, see table below for proper value. WARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME VALUE AND TYPE FUSE. MODEL 115 VAC 230 VAC CMA30 2A NB 1A NB CMA60 4A NB 2A NB CMA120 6A NB 3A NB CMA350 6.3A SB 3.15A SB 7 APPLICATIONS Commercial/Industrial Paging System CMA60

60 watt output BIAMP SYSTEMS an affiliate of send/return channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

Rauland-Borg Corp xfmr direct chime max phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute

E158021 4 com level line min rec amp pre level -40 -20 trim nominamin level -40 -20 level -40 -20 level -40 -20 level -40 -20 level -40 -20

LISTED 2 Z 91 COMMERCIAL 8 AUDIO EQUIP R R out out in max trim nominamin max trim nominamin max trim nominamin max trim nominamin max trim nominamin out max

C 6.3A - 115V 25V compressor auto mute priority on off line priority on off line priority on off line priority on off line priority on off line priority on off line

50V out min threshold adjust max min mic mic mic mic mic mic

70V remote mute/ tel

level stacking in

3.15A -230V USE ONLY WITH 250V FUSE ~ 115/230V AC 50/60 Hz 375 VA +10V c chime + + + + + + +

security paging mic 70V distributed speaker system background music source telephone paging line

This application shows a CMA60 being used in a commercial/industrial paging system. Channel #1 is set for input from the telephone paging line, and is assigned both as a priority channel and manual muting of -20dB. Channel #2 is set for input from the security paging microphone, which also has a push-to-talk switch wired to the Mute/Chime terminals of the CMA60. Channel #3 is set for input from the line-level background music source, and is assigned manual and auto muting of -20dB. Therefore, telephone paging will automatically mute only the background music, whereas, security paging will manually mute both the background music and the telephone paging. The CMA60 is set for 'xfmr' output and is connected to a 70V distributed speaker system. WARNING: THE ABOVE DIAGRAM SHOWS THE OUTPUT TERMINAL COVER REMOVED FOR CLARITY ONLY. THE COVER MUST BE INSTALLED WHEN THE UNIT IS ENERGIZED. 8 APPLICATIONS House of Worship Sound Reinforcement System MSP11 27V ~ BIAMP SYSTEMS

50/60 Hz 12 watts class 2 wiring CMA120 serial port link port link logic inputs output input output input MSP11 Portland, Oregon an affiliate of Rauland-Borg Corp. MADE IN U.S.A.

120 watt output BIAMP SYSTEMS an affiliate of send/return channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

Rauland-Borg Corp xfmr direct chime max phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute

E158021 4 com level line min rec amp pre level -40 -20 trim nominalmin level -40 -20 level -40 -20 level -40 -20 level -40 -20 level -40 -20

LISTED 2 Z 91 COMMERCIAL 8 AUDIO EQUIP R R out out in max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin out max

C 6.3A - 115V 25V compressor auto mute priority on off line priority on off line priority on off line priority on off line priority on off line priority on off line

50V out min threshold adjust max min mic mic mic mic mic mic

70V remote mute/ tel

level stacking in

3.15A -230V USE ONLY WITH 250V FUSE ~ 115/230V AC 50/60 Hz 375 VA +10V c chime + + + + + + +

auxiliary mixer two 8Ω speaker cabinets (4Ω load) tape deck choir mic choir mic wireless mic lectern mic pulpit mic

This application shows a CMA120 being used in a house of worship sound reinforcement system. Channels #1~5 are set for input from the various microphones. Channel #6 is set for input from the tape deck (playback), which is also connected to Rec Out of the CMA120 (recording). A BIAMP MSP11 is inserted between Pre Out & Amp In of the CMA120, providing equalization to compensate for room acoustics, and automatic gain control for consistent output levels. If additional inputs are required, an auxiliary mixer (such as a BIAMP 601) may be connected to the Stacking In terminals of the CMA120. The CMA120 is set for 'direct' (4Ω) output and is connected (in parallel) to the two 8Ω speaker cabinets. WARNING: THE ABOVE DIAGRAM SHOWS THE OUTPUT TERMINAL COVER REMOVED FOR CLARITY ONLY. THE COVER MUST BE INSTALLED WHEN THE UNIT IS ENERGIZED. 9

CMA30 30 watt output BIAMP SYSTEMS an affiliate of send/return APPLICATIONS Retail Store Paging System channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

Rauland-Borg Corp xfmr direct chime max phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute

E158021 8 com level line min rec amp pre level -40 -20 trim nominalmin level -40 -20 level -40 -20 level -40 -20 level -40 -20 level -40 -20

LISTED 2 Z 91 COMMERCIAL 4 AUDIO EQUIP R R out out in max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin out max

C 6.3A - 115V 25V compressor auto mute priority on off line priority on off line priority on off line priority on off line priority on off line priority on off line

50V out min threshold adjust max min mic mic mic mic mic mic

70V remote mute/ tel

level stacking in

3.15A -230V USE ONLY WITH 250V FUSE ~ 115/230V AC 50/60 Hz 375 VA +10V c chime + + + + + + +

store distributed speaker system CMA120 RP-L2 RP-L2 store level warehouse level background music source digital message repeater telephone paging line

120 watt output BIAMP SYSTEMS an affiliate of send/return channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

Rauland-Borg Corp xfmr direct chime max phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute

E158021 4 com level line min rec amp pre level -40 -20 trim nominalmin level -40 -20 level -40 -20 level -40 -20 level -40 -20 level -40 -20

LISTED 2 Z 91 COMMERCIAL 8 AUDIO EQUIP R R out out in max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin out max

C 6.3A - 115V 25V compressor auto mute priority on off line priority on off line priority on off line priority on off line priority on off line priority on off line

50V out min threshold adjust max min mic mic mic mic mic mic

70V remote mute/ tel

level stacking in

3.15A -230V USE ONLY WITH 250V FUSE ~ 115/230V AC 50/60 Hz 375 VA warehouse distributed speaker system +10V c chime + + + + + + + warehouse paging mic

This application shows a CMA30 and a CMA120 being used in a retail store paging system. Channel #1 of the CMA30 is set for input from the telephone paging line. The telephone system also provides a paging contact closure which is wired to the Mute/Chime terminals of the CMA30. Channel #2 of the CMA30 is set for input from the line-level digital message repeater, and is assigned both as a priority channel and manual muting of -20dB. Channel #3 of the CMA30 is set for input from the line-level background music source, and is assigned manual and auto muting of -10dB. Channel #1 of the CMA120 is set for input from the warehouse paging microphone, which also has a push-to-talk switch wired to the Mute/Chime terminals of the CMA120. Channel #6 of the CMA120 is set for input from the line-level Pre Out of the CMA30, and is assigned manual muting of -40dB. Therefore, the digital message repeater will automatically mute only the background music (-10dB), whereas, telephone paging will manually mute both the background music (-10dB) and the digital message repeater (-20dB). These combined signals from the CMA30 are then fed to the CMA120 in the warehouse, where they are manually muted by any warehouse paging (-40dB). RP-L2 potentiometers are wired to the Remote Level terminals of both the CMA30 and CMA120, providing remote control of store and warehouse levels. The CMA30 and CMA120 are set for 'xfmr' output and are connected to 70V distributed speaker systems. WARNING: THE ABOVE DIAGRAM SHOWS THE OUTPUT TERMINAL COVER REMOVED FOR CLARITY ONLY. THE COVER MUST BE INSTALLED WHEN THE UNIT IS ENERGIZED. 10 APPLICATIONS Multi-Floor Office/Hospital Paging System DA28R

27V ~ DA28R OUTPUTS INPUTS

50/60 Hz BIAMP SYSTEMS Portland, Oregon c i c i

m m g g an affiliate of Rauland-Borg Corp. o o

l o l o trim trim pad

level level level level level level level level pad

tr ev n i t n a hp tr ev n i t n a hp +10 +10

12 watts 2 1 class 2 wiring logic inputs logic inputs output 8 output 4 output 7 output 6 output 5 output 3 output 2 output 1 CH 2 CH 1

input/output assignment background music to Floors #1~3 CMA60 (Floor #1) H H C C all-call paging to Floors #1~3 background music source

60 watt output BIAMP SYSTEMS an affiliate of send/return channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

Rauland-Borg Corp xfmr direct chime max phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute

E158021 4 com level line min rec amp pre level -40 -20 trim nominalmin level -40 -20 level -40 -20 level -40 -20 level -40 -20 level -40 -20

70V R LISTED 2 Z 91 COMMERCIAL AUDIO EQUIP R out 8 out in max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin out max

distributed C 6.3A - 115V 25V compressor auto mute priority on off line priority on off line priority on off line priority on off line priority on off line priority on off line Floor #1

50V out min threshold adjust max min mic mic mic mic mic mic local

70V remote mute/ tel

level stacking in

speaker system (Floor #1) 3.15A -230V USE ONLY WITH 250V FUSE ~ 115/230V AC 50/60 Hz 375 VA +10V c chime + + + + + + + paging mic

CMA60 (Floor #2) 60 watt output BIAMP SYSTEMS an affiliate of send/return all-call paging background music channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

Rauland-Borg Corp xfmr direct chime max phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute

E158021 4 com level line min rec amp pre level -40 -20 trim nominalmin level -40 -20 level -40 -20 level -40 -20 level -40 -20 level -40 -20

70V R LISTED 2 Z 91 COMMERCIAL AUDIO EQUIP R out 8 out in max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin out max

distributed C 6.3A - 115V 25V compressor auto mute priority on off line priority on off line priority on off line priority on off line priority on off line priority on off line Floor #2

50V out min threshold adjust max min mic mic mic mic mic mic local

70V remote mute/ tel

level stacking in

speaker system (Floor #2) 3.15A -230V USE ONLY WITH 250V FUSE ~ 115/230V AC 50/60 Hz 375 VA +10V c chime + + + + + + + paging mic

CMA60 (Floor #3) 60 watt output BIAMP SYSTEMS an affiliate of send/return all-call paging background music channel 6 channel 5 channel 4 channel 3 channel 2 channel 1

Rauland-Borg Corp xfmr direct chime max phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute phantom pwr auto mute manual mute mute

E158021 4 com level line min rec amp pre level -40 -20 trim nominalmin level -40 -20 level -40 -20 level -40 -20 level -40 -20 level -40 -20

70V R LISTED 2 Z 91 COMMERCIAL AUDIO EQUIP R out 8 out in max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin max trim nominalmin out max

distributed C 6.3A - 115V 25V compressor auto mute priority on off line priority on off line priority on off line priority on off line priority on off line priority on off line Floor #3

50V out min threshold adjust max min mic mic mic mic mic mic local

70V remote mute/ tel

level stacking in

speaker system (Floor #3) 3.15A -230V USE ONLY WITH 250V FUSE ~ 115/230V AC 50/60 Hz 375 VA +10V c chime + + + + + + + paging mic

This application shows three CMA60s being used in a multi-floor office/hospital paging system. An all-call paging microphone and a background music source are connected to a BIAMP DA28R, which distributes those signals independently to the three CMA60s. Channel #1 of each CMA60 is set for input from line-level all-call paging, and is assigned as a priority channel. Channel #2 of each CMA60 is set for input from the respective floor paging microphone, and is assigned auto muting of -40dB. The push-to-talk switch of each floor paging microphone is wired to the Mute/Chime terminals of the respective CMA60. Channel #3 of each CMA60 is set for input from line-level background music, and is assigned manual and auto muting of -20dB. Therefore, local paging will manually mute the background music only on that floor (-20dB), whereas, all-call paging will automatically mute background music (-20dB) and local paging (-40dB) on all floors. The CMA60s are set for 'xfmr' output and are connected to 70V distributed speaker systems for each floor. WARNING: THE ABOVE DIAGRAM SHOWS THE OUTPUT TERMINAL COVER REMOVED FOR CLARITY ONLY. THE COVER MUST BE INSTALLED WHEN THE UNIT IS ENERGIZED. 11 SPECIFICATIONS CMA30, CMA60, & CMA120 Output Power: Input Impedance / Sensitivity CMA 30 30 Watts mic inputs 6kΩ / -77dBu (110µV) CMA 60 60 Watts line inputs 15kΩ / -37dBu (14mV) CMA 120 120 Watts telephone inputs 600Ω / -60dBu (775µV) Power Bandwidth (THD < 0.4%): amplifier input 10kΩ / +4dBu (1.2V) direct output 20Hz~20kHz stacking input 20kΩ / -8dBu (300mV) transformer output 50Hz~20kHz patch/return input 10kΩ / -8dBu (300mV) Frequency Response (+0/-1.5dB): Output Impedance / Level: direct output 20Hz~20kHz preamp output & line output 200Ω / +4dBu (1.2V) transformer output 50Hz~20kHz record output 200Ω / +4dBu (1.2V) Total Harmonic Distortion (1kHz @ rated power): < 0.2% patch/send output 50Ω / -8dBu (300mV) Output Regulation (no load to full load) < 0.5dB Amplifier Output Impedance / Level: Equivalent Input Noise (mic in, 150Ω termination): -123dBu CMA 30 CMA 60 CMA 120 Signal-to-Noise Ratio (20Hz-20kHz @ rated power): 4Ω / 11V 4Ω / 16V 4Ω / 22V line inputs 78dB 8Ω / 16V 8Ω / 22V 8Ω / 31V telephone inputs 78dB 20.8Ω / 25V 10.4Ω / 25V 5.2Ω / 25V master level off 98dB 83.3Ω / 50V 41.7Ω / 50V 20.8Ω / 50V Compressor: 163.3Ω / 70V 81.7Ω / 70V 40.8Ω / 70V attack time < 1mSecond 333.3Ω / 100V (export) 166.7Ω / 100V (export) 83.3Ω / 100V (export) release time > 1 Second Power Consumption (120VAC 60Hz / 240VAC 50Hz): compression ratio 4 : 1 CMA 30 CMA 60 CMA 120 threshold adjust range 15dB < 90W < 220W < 375W Dimensions (all models; includes rack/handles & feet): Weight: height (two rack spaces) 3.68" (93.5mm) CMA 30 17.64 lbs. (8kg) width 19" (482mm) CMA 60 22 lbs. (10kg) depth 14.33" (364mm) CMA 120 26.45 lbs. (12kg) CMA350 Output Power: 350 Watts Output Impedance / Level: Power Bandwidth (THD < 0.5%): record output, preamp output, & line output 200Ω / +4dBu (1.2V) direct output 20Hz~20kHz patch/send output 50Ω / -8dBu (300mV) transformer output 50Hz~20kHz Amplifier Output Impedance / Level: Frequency Response (+0/-1.5dB): 4Ω / 37.4V direct output 20Hz~20kHz 8Ω / 53V transformer output 50Hz~20kHz 1.8Ω / 25V THD + Noise (1kHz @ rated power): < 0.25% 7.1Ω / 50V Output Regulation (no load to full load) < 0.5dB 14Ω / 70V (28.6Ω / 100V export) Equivalent Input Noise (mic in, 150Ω termination): -123dBu Compressor: Signal-to-Noise Ratio (20Hz-20kHz @ rated power): attack time < 1mSecond line inputs & telephone input 78dB release time > 1 Second master level off 98dB compression ratio 4 : 1 Input Impedance / Sensitivity threshold adjust range 15dB mic inputs 6kΩ / -77dBu (110µV) Power Consumption (120/240VAC 60/50Hz): < 760 Watts line inputs 15kΩ / -37dBu (14mV) Dimensions (includes rack/handles & feet): telephone inputs 600Ω / -60dBu (775µV) height (three rack spaces) 5.24" (133mm) amplifier input 10kΩ / +4dBu (1.2V) width 19" (483mm) stacking input 20kΩ / -8dBu (300mV) depth 14" (356mm) patch/return input 10kΩ / -8dBu (300mV) Weight: 51 lbs. (23.13kg) 12 BLOCK DIAGRAM CMA30, CMA60, CMA120

input xformer Channel 1 + (mic/line/tel) mic/ tele phonephtm. trim e e t t u u y m m t i . . r o n x t o CMA 120 Block Diagram send/

line power ir a u i return

level - p a m m loudness bass treble

-40dB -20dB -10dB priority auto. mute man. mute rec out threshold stacking input + - level amp inpre out

input xformer (option) Channels chime trim compressor signal peak fault

2 thru 6 + remote

(mic/line) mic/ linephtm. control

- power -40dB -20dB -10dB auto. mute level priority threshold auto. mute mute/ chime master level +10V C low-cut power amplifier line out 4Ω 8Ω 25V 50V 70V* com

input xformer Channel 1 + (mic/line/tel) mic/ line tele phonephtm. power man. mute trim CMA350 y t i r o i r e t u m . o tu e t u m . n a *100V output available (export option) CMA 350 Block Diagram send/ x return i

level - p a m m loudness bass treble

-40dB -20dB -10dB priority auto. mute man. mute rec out threshold stacking input + - level amp inpre out

+ Channels 2 thru 6 (mic/line) mic/ linephtm. chime trim remote control compressor signal peak fault

- power -40dB -20dB -10dB auto. mute level priority threshold auto. mute mute/ chime master level +10V C low-cut power amplifier line out 4Ω 8Ω 25V 50V 70V* com

man. mute *100V output available (export option)

13 WARRANTY BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL.

BIAMP Systems expressly warrants this product to be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase as a new product from an authorized BIAMP Systems dealer under the following conditions. 1. In the event the warranted BIAMP Systems product requires service during the warranty period, BIAMP Systems will repair or replace, at its option, defective materials, provided you have identified yourself as the original purchaser of the product to any authorized BIAMP Systems Service Center. Transportation and insurance charges to and from an authorized Service Center or the BIAMP Systems factory for warranted products or components thereof to obtain repairs shall be the responsibility of the purchaser. 2. This warranty will be VOIDED if the serial number has been removed or defaced; or if the product has been subjected to accidental damage, abuse, rental usage, alterations, or attempted repair by any person not authorized by BIAMP Systems to make repairs; or if the product has been installed contrary to BIAMP Systems's recommendations. 3. Electro-mechanical fans, electrolytic capacitors, and the normal wear and tear of appearance items such as paint, knobs, handles, and covers are not covered under this warranty. 4. BIAMP SYSTEMS SHALL NOT IN ANY EVENT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING LOST PROFITS, LOSS OF USE, PROPERTY DAMAGE, INJURY TO GOODWILL, OR OTHER ECONOMIC LOSS OF ANY SORT. EXCEPT AS EXPRESSLY PROVIDED HEREIN, BIAMP SYSTEMS DISCLAIMS ALL OTHER LIABILITY TO PURCHASER OR ANY OTHER PERSONS ARISING OUT OF USE OR PERFORMANCE OF THE PRODUCT, INCLUDING LIABILITY FOR NEGLIGENCE OR STRICT LIABILITY IN TORT. 5. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. BIAMP SYSTEMS EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE REMEDIES SET FORTH HEREIN SHALL BE THE PURCHASER'S SOLE AND EXCLUSIVE REMEDIES WITH RESPECT TO ANY DEFECTIVE PRODUCT. THE AGENTS, EMPLOYEES, DISTRIBUTORS, AND DEALERS OF BIAMP SYSTEMS ARE NOT AUTHORIZED TO MODIFY THIS WARRANTY OR TO MAKE ADDITIONAL WARRANTIES BINDING ON BIAMP SYSTEMS. ACCORDINGLY, ADDITIONAL STATEMENTS SUCH AS DEALER ADVERTISEMENTS OR REPRESENTATIONS DO NOT CONSTITUTE WARRANTIES BY BIAMP SYSTEMS. 6. No action for breach of this warranty may be commenced more than one year after the expiration of this warranty.

Thank you for purchasing BIAMP SYSTEMS... AMERICAN SOUND CRAFTSMANSHIP Biamp Systems 10074 S.W. Arctic Drive Beaverton, Oregon 97005 (503) 641-7287 585.8030.00


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply