Free English BENQ V3251 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD BENQ V3251 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I unpack the BENQ V3251?
The display carton disconnects from its base and lifts off over the top of the display. Follow the instructions on the carton to remove the upper carton from the base. Carefully unpack the display and accessories from the delivery carton by lifting the display from the base while being careful to avoid damage to the display.
What safety precautions should I take when installing the BENQ V3251?
Observe the following points when installing the BENQ V3251:
Do not place the display on an uneven, sloping or unstable surface.
Do not place the display near water, such as a spa or pool, or where splashing or spraying of water can occur.
Do not place the display near or above sources of heat, such as radiators, heaters, or fuel stoves.
Do not place the display in direct sun or where direct sun or spot lighting will shine onto the display.
If recessed into a wall opening, leave at least 50 to 100 mm of free space both top and bottom for ventilation.
If wall mounting, allow at least 30 mm of space on top for attaching the display to the wall bracket.
Do not cover or block the vents and openings while the display is switched on.
Do not place the display in an enclosed place without allowing for ventilation.
How do I connect the antenna cable to the BENQ V3251?
Connect a TV antenna cable fly-lead from your TV antenna system or Cable TV system to the antenna input on the rear of the BENQ V3251.
How do I connect the power cable to the BENQ V3251?
Step 1. Locate the power cable from the packaging and plug the appropriate end into the AC input socket on the rear of the BENQ V3251.
Step 2. Connect the other end into a wall power outlet and switch it on. The display will enter standby mode and the power indicator on the front lower right will light up red.
How do I activate the remote control for the BENQ V3251?
Step 1. Turn the remote control end up and open the battery compartment lid by using a small coin to rotate the slot 90 degrees anticlockwise.
Step 2. Insert the batteries ensuring the positive and negative terminals match the (+) and (-) marks in the compartment.
Step 3. Refit the lid by inserting the hinge into the recess and levering it down.
Step 4. Use a small coin to rotate the locking slot 90 degrees clockwise to lock the lid in place.
How do I initialize the BENQ V3251?
When first turned on, the First Turn On menu will appear. Use the left, right, up, and down buttons on the remote control or display to navigate, and the OK button or Input button to make selections. Select your language, country, and TV standard. Then, select the Auto Installation menu item and press the OK button to allow the BENQ V3251 to search for, tune, sort, and store available programs.
How do I clean the screen of the BENQ V3251?
Always turn off the BENQ V3251 before cleaning. Do not use cream, liquid, aerosol, or spray cleaners. Use only a slightly damp, lint-free, clean soft cloth and lightly wipe the display. If necessary, use a pH-neutral liquid dish-washing detergent diluted with water on a separate lint-free cloth to remove oil or grease marks, then wipe again with a clean dry lint-free cloth.
How do I use the BENQ V3251 PIP function?
If the BENQ V3251 is connected to both a video and a graphic source, press the PIP button to display both images simultaneously. Select between Full Screen or Video On Graphic mode in the Window menu.
What should I do if the BENQ V3251 power does not turn on?
Check that the power plug is securely inserted into both the AC Mains socket on the display and the wall outlet, and that the wall outlet is switched on. Also, check that power is available from the wall outlet by testing it with another appliance.
What does it mean if the power indicator on the BENQ V3251 flashes red?
This indicates that the PC cable is disconnected, the PC input has been selected with no PC source signal available, or the BENQ V3251 has been placed in PC standby mode.
What are the signal input options for the BENQ V3251?
The BENQ V3251 supports the following input sources:
Analog TV source: 1 x Coaxial analog TV Antenna (BNL).
Video source inputs: 2 x S-Video, 2 x Composite Video, 2 x SCART.
Graphic source inputs: 2 x Component Video (Y/Pb/Pr) or (Y/Cb/Cr), 1 x HDMI/DVI, 1 x PC D-Sub.
How can I perform a manual program installation on the BENQ V3251?
Access the TV menu and select Manual Installation. From here, you can select the TV standard, set the program channel (Selected PR), input the frequency, fine-tune the signal, configure decoder settings (Decode) for SCART inputs, select the text code format for Teletext, and store the program into memory.
How do I enable the child lock on the BENQ V3251?
In the TV menu, select Child Lock and enter your password (default is 0000). Set the Child Lock Activate option to On.
What are the SCART output signal capabilities of the BENQ V3251?
The SCART terminals on the BENQ V3251 can output different signals depending on the input source selected. The following table summarizes these outputs:
| Selected input | Corresponding AV1 SCART output | Corresponding AV2 SCART output |
|---|---|---|
| ATV | ATV | ATV |
| AV1 (Composite Video) | ATV | AV1 (Composite Video) |
| AV1 RGB | ATV | ATV |
| AV2 (Composite/S-Video) | ATV | ATV |
| AV3/AV4 (Composite/S-Video) | ATV | AV3/AV4 (S-Video recombined as Composite Video) |
| Component 1/2 | ATV | ATV |
| PC | ATV | ATV |
| HDMI (DVI) | ATV | ATV |
CLICK HERE TO DOWNLOAD BENQ V3251 (01) PDF DOCUMENT