Free English BENINCA ONE.2WB (01) PDF Document. Free English BENINCA ONE.2WB (01) PDF User Guide. Free English BENINCA ONE.2WB (01) PDF User Manual. Free English BENINCA ONE.2WB (01) PDF Owner Guide. Free English BENINCA ONE.2WB (01) PDF Owner Manual. Free English BENINCA ONE.2WB (01) PDF Reference Guide. Free English BENINCA ONE.2WB (01) PDF Instruction Guide. Free English BENINCA ONE.2WB (01) PDF Reference Manual. Free English BENINCA ONE.2WB (01) PDF Instruction Manual. Free English BENINCA ONE.2WB (01) PDF Operating Instructions.
CLICK HERE TO DOWNLOAD BENINCA ONE.2WB (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I program Channel 1 to Pulse on my BENINCA ONE.2WB Radio Receiver?
To set Channel 1 to Pulse mode on your BENINCA ONE.2WB, please follow these steps:
1. Press and release the P button once.
2. The LED will flash RED, then turn off.
3. The LED will then light up solid RED. Within 10 seconds, press the transmitter button. If you have more than one transmitter, you can press one after the other within the 10 seconds slot.
4. Leave the receiver to time out, which takes approximately 10 seconds.
How do I program Channel 2 to Pulse on my BENINCA ONE.2WB Radio Receiver?
To set Channel 2 to Pulse mode on your BENINCA ONE.2WB, please follow these steps:
1. Press and release the P button twice.
2. The LED will flash GREEN, then turn off.
3. The LED will then light up solid GREEN. Within 10 seconds, press the transmitter button. If you have more than one transmitter, you can press one after the other within the 10 seconds slot.
4. Leave the receiver to time out, which takes approximately 10 seconds.
How do I program Channel 1 to Latch on my BENINCA ONE.2WB Radio Receiver?
To set Channel 1 to Latch mode on your BENINCA ONE.2WB, please follow these steps:
1. Press and release the P button 4 times.
2. The LED will flash RED 5 times followed by one quick RED pulse.
3. Press and hold the P button for at least 3 seconds. Upon release, you will see two RED flashes.
4. Press and hold the P button for at least 3 seconds again. Upon release, you will see three RED flashes.
5. Press the P button momentarily. The BENINCA ONE.2WB receiver will now latch relay one on radio command.
How do I program Channel 2 to Latch on my BENINCA ONE.2WB Radio Receiver?
To set Channel 2 to Latch mode on your BENINCA ONE.2WB, please follow these steps:
1. Press and release the P button 5 times.
2. The LED will flash GREEN 5 times followed by one quick GREEN pulse.
3. Press and hold the P button for at least 3 seconds. Upon release, you will see two GREEN flashes.
4. Press and hold the P button for at least 3 seconds again. Upon release, you will see three GREEN flashes.
5. Press the P button momentarily. The BENINCA ONE.2WB receiver will now latch relay two on radio command.
What are the terminal connections for the BENINCA ONE.2WB Radio Receiver?
The terminal connections for the BENINCA ONE.2WB are as follows:
Terminals 1 & 2: CH 1 N.O. (Normally Open)
Terminals 3 & 4: CH 2 N.O. (Normally Open)
Terminal 5: – (Negative for 12-28Vdc power supply)
Terminal 6: + (Positive for 12-28Vdc or 21-28Vac power supply)
Terminal 7: SHI (Antenna Shield)
Terminal 8: ANT (Antenna Core)
CLICK HERE TO DOWNLOAD BENINCA ONE.2WB (01) PDF DOCUMENT