BEAUTIFUL PERFECT GRIND 19332 (01) PDF MANUAL

BEAUTIFUL PERFECT GRIND 19332 (01) PDF SUMMARY:

How do I set the current time on the Perfect Grind™ Single Serve Coffee Maker?

Plug the power cord into a 120V AC electrical outlet. When the Coffee Maker is plugged in, an audible tone will sound, and the control panel will illuminate. 12:00 AM will begin to flash on the display. Press the BREW/OFF button. The DELAY/MENU and HOUR/MINUTE buttons will illuminate. Press the HOUR/ MINUTE buttons to adjust the hours, holding the button down to scroll through the digits quickly. Press DELAY/MENU to confirm the set hour. Pay attention to the AM and PM setting. Press the HOUR/ MINUTE buttons to adjust the minutes, holding the button down to scroll through digits quickly. Press DELAY/MENU to confirm the set minutes. If DELAY/MENU is not pressed to confirm, the Coffee Maker will remain in current mode and turn off after 5 minutes. To adjust the time after brewing, press and hold DELAY/MENU for 1.5 seconds. Press the HOUR/MINUTE button when it appears on the toggling display. Follow the instructions previously described to set and confirm both HOURS and MINUTES.

---

How do I set up a brew using whole bean coffee?

Ensure the water reservoir is filled to a sufficient level, but never add water to exceed the MAX line. Ensure the coffee bean hopper is full of coffee beans, with a max capacity of up to 180g, depending on the type and size of coffee bean being used. If the Grinder Off icon flashes three times and the unit returns to standby mode, this indicates that the grinder protective cover is not locked in the correct position. Make sure to remove the protective cover and then reposition it correctly into place. Remove the brew chamber drawer by pulling it outwards and ensure the gold tone filter basket is free of ground coffee or any residue. If there is any remaining ground coffee from the last brew, empty the gold tone filter basket and wash, rinse and dry. Replace the gold tone filter basket, push the top cover down, and reinsert the brew chamber drawer. Do not use a paper filter with this unit, as there are no compatible size paper filters available. The gold tone filter included with this unit is custom designed for optimal performance and best brew quality and taste with this coffee maker. Failing to remove pre-existing coffee grounds can result in the Coffee Maker overflowing. Place an empty cup or mug onto the drip tray, removing the drip tray to accommodate up to a 7” tumbler. Press BREW SIZE until the desired size appears on the display, choosing from 6 sizes: 6 oz., 8 oz., 10 oz., 12 oz., 14 oz., or 16 oz. Adjust BREW STRENGTH if desired by pressing BOLD/OVER ICE for a more robust brew or for brewing iced beverages. BOLD or OVER ICE brew strength is displayed. Press BREW/OFF to grind and brew coffee with the selected settings shown on the display. The Coffee Maker will display a circling animation during the brew cycle. The display will show FILL H2o if there is no water in the water tank. Add water up to the MAX line, and press Brew/Off to continue brewing within 5 minutes. If the brew chamber drawer has not been removed since the last brew, 3 audible tones will sound and FULL, OPEN, DOOR will appear on the display. Once the brew chamber drawer has been removed, the gold tone filter basket emptied, and brew chamber drawer has been replaced, the Coffee Maker will return to the standby status. To avoid the risk of injury, do not open the brew chamber drawer while coffee is brewing, as scalding may occur if the drawer is opened during the BREW cycle. It is not recommended to grind and brew more than 4 times consecutively. Wait at least 15 minutes before grinding and brewing again to allow the motor to properly cool down so that it will not overheat.

---

How do I set up a brew using ground coffee?

Ensure the water reservoir is filled to a sufficient level, but never add water to exceed the MAX line. Open the brew chamber drawer by pulling it outwards and ensure the gold tone filter basket is free of ground coffee or any residue. If there is any remaining ground coffee from the last brew, empty the gold tone filter basket and wash, rinse and dry. Failing to remove pre-existing coffee grounds can result in the Coffee Maker overflowing. Add the amount of coffee to the gold tone filter basket based on the desired cup size as indicated in the chart, but do not add more than 40g of coffee. Do not use a paper filter with this unit, as there are no compatible size paper filters available. The gold tone filter included with this unit is custom designed for optimal performance and best brew quality and taste with this coffee maker. Fold the gold tone filter basket cover down, place it into the brew chamber drawer and re-insert it into the Coffee Maker. Place an empty cup or mug onto the drip tray, removing the drip tray to accommodate up to a 7” tumbler. Press GRINDER OFF to turn off the grinder, so GRINDER OFF is displayed. Press BREW SIZE until the desired size appears on the display, choosing from 6 sizes: 6 oz., 8 oz., 10 oz., 12 oz., 14 oz., or 16 oz. Adjust BREW STRENGTH if desired by pressing BOLD/OVER ICE for brewing iced beverages, so OVER ICE brew strength is displayed. Press BREW/OFF to brew coffee with the selected settings shown on the display. The Coffee Maker will display a circling animation during the brew cycle. If the brew chamber drawer has not been removed since the last brew, 3 audible tones will sound and FULL, OPEN, DOOR will appear on the display. Once the brew chamber drawer has been removed, the gold tone filter basket emptied, and brew chamber drawer has been replaced, the Coffee Maker will return to the standby status. To avoid the risk of injury, do not open the brew chamber drawer while coffee is brewing, as scalding may occur if the drawer is opened during the BREW cycle.

---

How much ground coffee should I use for each brew size?

• 6oz: 2 scoops, 10 g
• 8oz: 2.5 scoops, 12.5 g
• 10oz: 3.5 scoops, 17.5 g
• 12oz: 4 scoops, 20 g
• 14oz: 4.5 scoops, 22.5 g
• 16oz: 5.5 scoops, 27.5 g

---

How do I grind and brew coffee later?

The Coffee Maker can be programmed to begin grinding & brewing up to 24 hours in the future. Make sure the Coffee Maker is set up to brew coffee. Press DELAY/MENU to begin the process, so the FUTURE BREW TIME will appear on the display with flashing hours and the DELAY Indicator will appear flashing. Press HOUR/ MINUTE to adjust the HOURS, holding the button down to scroll through the digits quickly. Press DELAY/MENU to confirm the set hour, and pay attention to the AM and PM setting. Press HOUR/ MINUTE to adjust MINUTES, holding the button down to scroll through digits quickly. Press DELAY/MENU to confirm the desired FUTURE BREW TIME. The BREW SIZE, BOLD/OVER ICE and GRINDER OFF buttons will illuminate. Press BREW SIZE until the desired size appears on the display. Adjust BREW STRENGTH if desired by pressing BOLD/OVER ICE for a more robust brew or for brewing iced beverages, so BOLD or OVER ICE brew strength is displayed. If using ground coffee is desired instead of whole beans, press GRINDER OFF to turn off the grinder, so GRINDER OFF is displayed. With the desired settings selected, press DELAY/MENU to confirm the program, so the DELAY Indicator will appear solid on the display along with current time. If DELAY/MENU is not pressed to confirm, the Coffee Maker will rest in this state and turn OFF after 5 minutes. The Coffee Maker will not be ready to brew in the future. If the brew chamber drawer has not been removed since the last brew, 3 audible tones will sound and FULL, OPEN, DOOR will appear on the display. Once the brew chamber drawer has been removed, the gold tone filter basket emptied, and brew chamber drawer has been replaced, the Coffee Maker will return to the standby status. While the program set, the user can view the FUTURE BREW TIME and future brew settings. The program can also be cancelled if desired by pressing and holding DELAY/MENU for 1.5 seconds. While the program is set, the Coffee Maker is unable to brew coffee until the program has been completed or cancelled. Press DELAY/MENU to view the FUTURE BREW TIME. Press DELAY/MENU again to view the future brew settings. When the pre-programmed time is reached, the Coffee Maker will grind & brew coffee. When using the Delay Brew function, always make sure to empty the filter basket after your last brew. If the brew basket is not emptied, Full Open Door message will be displayed on the screen.

---

What are some hints for great tasting coffee?

A clean Coffee Maker is essential for brewing great tasting coffee. Regular cleaning is suggested monthly or whenever brewing becomes sluggish or the flavor is off, following detailed procedures described in the Brew Clean: Decalcification and Grinder Auto Clean sections of this instruction manual. Always use fresh, filtered or distilled cold water in your Coffee Maker. Press BOLD/OVER ICE for a more robust brew. Reheating coffee is not recommended. Coffee is at its peak flavor immediately after brewing. Small oil droplets on the surface of brewed, black coffee is due to the extraction of oil from the coffee grounds. Oiliness may occur more frequently if heavily roasted coffees are used. Overextraction may also cause oiliness, indicating a need to clean your Coffee Maker.

---

How do I care for and clean the Perfect Grind™ Single Serve Coffee Maker?

Always make sure the Coffee Maker is unplugged and cool before attempting to clean. Thoroughly clean the removable brew chamber drawer, gold tone filter basket and coffee scoop in hot, sudsy water. Rinse and dry. Replace disassembled parts. Wipe the coffee bean lid and hopper with a clean, dry paper towel. The gold tone filter basket is top-rack dishwasher safe. The coffee scoop should be placed in the dishwasher alongside the cutlery. Wipe the Coffee Maker exterior with a damp cloth to remove superficial stains. For stubborn stains, use a nylon or plastic pad with a non-abrasive cleanser. Do not use metal scouring pads or abrasive cleansers on any parts or surfaces of the Coffee Maker. Dry and replace disassembled parts. Insert the clean gold tone filter basket into the brew chamber drawer. Push the gold tone filter basket cover down. Close the brew chamber drawer.

---

How do I perform brew clean decalcification?

Minerals in water can detract from the flavor of the coffee and possibly lengthen brew time. To assure optimal flavor and performance, it is recommended that the CLEAN cycle be performed when the CLEAN indicator illuminates.

• CLEAN will flash on the display.
• Before running the CLEAN cycle, remove the charcoal filter and filter holder from the water reservoir and set aside for later use.
• Always remove the gold tone filter basket before running the CLEAN cycle.

Remove the drip tray and insert a large container with a capacity of at least 64 oz. underneath the brew chamber drawer. Press and hold DELAY/MENU for 1.5 seconds. Press the BREW SIZE button when it appears on the toggling display to enter CLEAN mode. When the BREW SIZE button is flashing and the message FILL, CLn is displayed, fill the reservoir with the cleaning solution: 2 parts water and 1 part vinegar. With the reservoir filled with cleaning solution, press BREW SIZE to begin the CLEAN cycle. Press and Hold BREW/OFF for 1.5 seconds at any time to turn the Coffee Maker OFF. Once the Coffee Maker has cycled all of the cleaning solution, carefully empty the container into the sink. The cleaning solution will be hot, so use extreme care when handling and emptying the container. When the BREW SIZE button is flashing and the message FILL, H2O is displayed, fill the reservoir with clean, cold water. With the reservoir filled with water, press BREW SIZE to continue the CLEAN cycle. Press BREW/OFF at any time to turn the Coffee Maker OFF. Once the Coffee Maker has cycled all of the water, carefully empty the container into the sink. The water will be hot, so use extreme care when handling and emptying the container. The CLEAN cycle is now complete. The unit will return to the home screen and the CLEAN indicator will disappear until the next time it is recommended to be run. Dry parts thoroughly. Replace the gold tone filter basket into the brew chamber drawer and reinstall it into the Coffee Maker. Reinstall the charcoal filter and filter holder into the water reservoir.

---

How do I clean the grinder door and channel?

It is recommended to clean the grinder door and channel every two weeks or as needed. Ensure the brew chamber drawer is installed and securely locked in the Coffee Maker. To access the internal grinder channel, press and hold GRINDER OFF for 1.5 seconds. The Coffee Maker will display a circling animation while the door is opening. If the brew chamber drawer is not securely locked, 3 audible tones will sound and PUSH DOOR will appear on the display. Once the brew chamber drawer is securely locked, the Coffee Maker will return to the home screen. When the brew chamber drawer is not securely locked, the GRINDER OFF button can’t be pressed. Once the door is fully open the message OPEN will be displayed. The brew chamber drawer can now be removed to access the grinder door and channel. Use the cleaning brush to clear any residual coffee from around the grinder door. Use the cleaning brush to clear any residual coffee from the grinder channel by sweeping outwards, towards the front of the Coffee Maker. Reinstall the brew chamber drawer and ensure it is securely locked. Press and hold GRINDER OFF for 1.5 seconds. The Coffee Maker will display a circling animation when the door is opening. If the brew chamber drawer is not securely locked, 3 audible tones will sound and PUSH DOOR will appear on the display. Once the brew chamber drawer is securely locked, the Coffee Maker will return to the home screen.

---

How do I perform the grinder auto clean?

It is recommended to clean the grinder every week or as needed. The bean hopper must be completely empty of coffee beans before running the Grinder Auto Clean cycle. Unplug the Coffee Maker power cord. Lift to remove the bean hopper lid and check to make sure the bean hopper is free from coffee beans and any debris. Turn the Grinder Protective Cover counterclockwise to unlock and remove from the Coffee Maker. Lift up the metal handle on the Top Grinder Burr, grasping firmly, and rotate the Top Grinder Burr counterclockwise to unlock and remove from the Coffee Maker. Using the cleaning brush, clear any residual coffee and debris from the grinder chamber. Using the cleaning brush, clear any residual coffee from both top and bottom grinding burrs. Replace the Top Grinder Burr by rotating clockwise to lock in place. Replace the Grinder Protective cover by rotating clockwise. Ensure the Grinder Protective Cover is fully installed, and there will be a tactile click when the cover is fully installed. Do not use excessive force when reinstalled the Grinder Protective Cover. Replace the lid and plug the unit in to 120V AC power. Ensure the gold tone filter basket and brew chamber drawer are installed. Press and hold DELAY/MENU for 1.5 seconds. Press the GRINDER OFF button when it appears on the toggling display to enter Grinder Auto Clean mode. When the GRINDER OFF button is flashing and the message CLr is displayed, press GRINDER OFF to run the Grinder Auto Clean cycle. The grinder will run for 20 seconds to clean the bean hopper channel. Remove the brew chamber drawer and empty any ground coffee from the gold tone filter basket and reinstall the brew chamber drawer. If the brew chamber drawer is not securely locked, 3 audible tones will sound and PUSH DOOR will appear on the display. Once the brew chamber drawer is securely locked, the Coffee Maker will return to the home screen.

---

What do the alert messages on the display mean?

ALERT MESSAGES APPEARING ON DISPLAY	REASON	SOLUTION
FULL OPEN DOOR	Drawer has not been removed & filter cleaned out from the last brew cycle	Remove drawer, empty coffee grinds from the filter basket. Clean and replace.
FILL H2O	Unit ran out of water during brewing	Refill reservoir with clean cold water and press BREW/OFF within 10 minutes. Note: After 10 minutes of inactivity, the coffee maker will return to sleep mode.
PUSH DOOR	Drawer is not inserted properly into unit	Push drawer until fully inserted
“GRINDER OFF” light flashing & beeping 3 times	Grinder protective cover is not properly inserted into place	Ensure that your grinder protective cover is securely locked in place

---

How should I store the Perfect Grind™ Single Serve Coffee Maker?

Never store the Coffee Maker while it is still plugged in. Ensure the water reservoir is complete empty before storing. Unplug the Coffee Maker and allow it to cool before storing. Store the Coffee Maker fully assembled, with the gold tone filter basket installed. Close the brew chamber drawer and make sure the bean hopper lid is in place. Store Coffee Maker in its box or in a cool, dry place. Store Coffee Maker in its upright position – not on its side or upside down.

---

My Perfect Grind™ Coffee Maker stopped working. What should I do?

• Check to ensure the unit is properly plugged in
• Make sure the water reservoir is filled past the min line and under the max line
• Make sure there are enough coffee beans in the bean hopper but never fill with more than 180g/6oz of coffee beans (approximately half a standard size bag of coffee beans)
• Clean the grinder door / grinder channel
• Grinder auto clean
• Descale the coffee maker
• Be sure to descale the unit when the clean icon appears on your screen for optimal performance or as needed

---

My Perfect Grind™ Coffee Maker no longer grinds coffee beans / is clogged. What should I do?

• Make sure there are enough coffee beans in the bean hopper but never fill with more than 180g/6oz of coffee beans (approximately half a standard size bag of coffee beans)
• Clean the grinder door / grinder channel
• Grinder Auto Clean

---

My Perfect Grind™ Grinder Door is jammed. What should I do?

Clean the grinder door / grinder channel.

---

My coffee isn’t strong enough / my coffee tastes too weak. What should I do?

• Press BOLD/OVER ICE for a more robust brew
• Always use freshly roasted coffee beans for optimal strength & flavor
• Make sure the cover of the permanent gold tone filter basket is securely in place
• Clean the grinder door / grinder channel
• Grinder Auto Clean
• Descale the coffee maker

---

My coffee isn’t hot enough. What should I do?

• Brew water through the coffee maker to preheat the unit & heat your cup, remembering to turn “GRINDER OFF” when doing this step
• Descale the coffee maker

---

No coffee came out while brewing / stopped brewing mid cycle. What should I do?

• If “Fill H2O” appears on the display, re-fill reservoir with clean cold water to the max line and press BREW/OFF within 10 minutes to continue the brew cycle
• Always check to ensure there is a sufficient amount of beans in the bean hopper or it will result in weak tasting coffee or will not brew properly

---

How often should I clean my Perfect Grind™ Coffee Maker?

• Clean the grinder door / grinder channel and surrounding area every 2 weeks or as needed for optimal performance
• Clean the grinder (grinder auto clean function) weekly for optimal performance & to avoid clogging the grinder
• Descale the coffee maker when the “clean” icon illuminates on your Perfect Grind™ display

---

How often do I have to replace my charcoal water filter?

Replace the charcoal filter every 60 days or every 60 water tank refills. If you live in areas where you have hard water, it should be replaced more frequently. It is compatible with most standard size charcoal water filters for coffee makers.

---

Are any parts dishwasher safe?

The gold tone filter basket & 2-in-1 cleaning brush measuring scoop are dishwasher safe.

---

Can I use a paper filter?

Do not use a paper filter with this unit, as there are no compatible size paper filters available. The gold tone filter included with this unit is custom designed for optimal performance and best brew quality and taste with this coffee maker.

---

What are some tips for best tasting coffee?

• Make sure your Perfect Grind™ coffee maker is clean
• It is recommended to use light or medium roasted coffee beans
• It is recommended that you use freshly roasted coffee beans to ensure optimal flavor
• Store coffee beans in a cool, air tight dark container
• Always use fresh cold water
• Reheating coffee is not recommended, since coffee is at its peak flavor immediately after brewing.
• If using pre-ground coffee, it is recommended to use medium ground coffee. Using a fine ground coffee can result in overflow, while using coarse ground coffee can result in weak tasting flavor.

---

What does the Beautiful Perfect Grind™ Single Serve Coffee Maker warranty cover?

For a period of TWO YEARS from the date of purchase, this product will be free from mechanical defects in material and workmanship, and for 90 days in respect to non-mechanical parts. At its sole discretion, Sensio Inc. dba Made by Gather™ will either repair or replace the product found to be defective, or issue a refund on the product during the warranty period. The warranty is only valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt, as proof of purchase is required to obtain warranty validation. Retail stores selling this product do not have the right to alter, modify, or in any way revise the terms and conditions of the warranty.

---

What does the Beautiful Perfect Grind™ Single Serve Coffee Maker warranty exclude?

The warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use of the product, use of improper voltage or current, improper routine maintenance, use contrary to the operating instructions, disassembly, repair, or alteration by anyone other than qualified Sensio Inc. dba Made by Gather™ personnel. Also, the warranty does not cover Acts of God such as fire, floods, hurricanes, or tornadoes.

---

How do I obtain warranty service?

Contact Customer Service at the toll-free number: 1-877-775-3564. A Customer Service Representative will attempt to resolve warranty issues over the phone. If the Customer Service Representative is unable to resolve the problem, you will be provided with a case number and asked to return the product to Sensio Inc. dba Made by Gather™. Attach a tag to the product that includes your name, address, daytime contact telephone number, case number, and description of the problem. Also, include a copy of the original sales receipt. Carefully package the tagged product with the sales receipt, and send it (with shipping and insurance prepaid) to SENSIO Inc.’s address. Sensio Inc. dba Made by Gather™ shall bear no responsibility or liability for the returned product while in transit to Sensio Inc. dba Made by Gather™ Customer Service Center.