FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF USER GUIDE
FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF USER MANUAL
FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF OWNER GUIDE
FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF OWNER MANUAL
FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF REFERENCE GUIDE
FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF INSTRUCTION GUIDE
FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF REFERENCE MANUAL
FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF INSTRUCTION MANUAL
FREE ENGLISH BALBOA INSTRUMENTS VS500Z (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD BALBOA INSTRUMENTS VS500Z (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is J23 + W1 used for?
2-Speed Pump 1
OR 1-Speed Pump 1 with DIP Switch A5
What is J50 + W4 used for?
Audio Visual – always hot, no relay
What is J17/26 + W7 used for?
1-Speed Blower (W3 to J46)
OR Single-Speed Pump 2 or Pump 3 (W3 to J62)
What is J47 + W2 used for?
Circ Pump
What is J29 + W2 used for?
Ozone (Same voltage as Circ Pump, if used)
Note X-03 option board for retro fit
What is J20 used for?
Spa Light (12V only)
How to convert to 120V?
Add jumper from Red AC (J32) to White AC (J11) and set DIP switch A10 to ON.
What is X-P (PN 53544) used for?
Used for a 1-speed Pump output.
What is X-B (PN 53310) used for?
Used for a Blower output ONLY.
What is X-P231 (PN 53681) used for and how is it connected?
Can replace the X-P in cases where branch circuit protection is needed for high amperage devices that would over-burden power input fuse F5 (1-A) on the main PCBA.
J6 on the X-P231 connects directly to Black AC by using J66 or J65 on the main board (1-B).
Connect J7 wire on the X-P231 to J60 on the main board (7-E).
Connect W1 on the X-P231 to Red AC on the main board (2-D).
What is X-P332 (PN 55137) used for and how is it connected?
Used for an additional 2-speed Pump output.
J6 on the X-P332 connects directly to Black AC by using J66 or J65 on the main board (1-B).
Connect J7 wire on the X-P332 to J13 on the main board (9-E).
Connect W1 on the X-P332 to Red AC on the main board (2-D).
What is the X-2SP Kit (PN 53913) used for and how is it connected?
Adapter PN 25339 is used in conjunction with an X-03 to run a 2-speed pump 2. No Blower is available when this kit is used.
J4 connects to Black AC (3-A) using J61 or J62 on main board.
Connect 2-speed pump to J7 on X-03.
What is X-Mount P (PN 53933) used for?
Used for mounting any Expander Board in a plastic enclosure. Standoffs attach to heater mounting bracket.
How does J12 setting affect system compatibility?
When J12 on the Main Board is jumpered on pins 2 & 3, the system is in VS50XZ compatibility mode.
If J12 on the Main Board is jumpered on pins 1 & 2, the system is in VS51XZ/VS5xxSZ/VS5xxDZ compatibility mode.
CLICK HERE TO DOWNLOAD BALBOA INSTRUMENTS VS500Z (01) PDF MANUAL