BAKERS PRIDE BPSP (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD BAKERS PRIDE BPSP (01) PDF MANUAL


PDF Content Summary: OPERATION MANUAL RESTAURANT SERIES EQUIPMENT: SALAMANDER, CHEESEMELTER, & STOCKPOT SERIES: BPSBi, BPCMi, BPSP BUILT BY CRAFTSMEN. TESTED BY TIME ®. C-SERIES OPERATION MANUAL C-SERIES RESTAURANT EQUIPMENT Models: BPSP – Stockpot BPCMi – Cheese Melter BPSBi – Salamander All gas operated Bakers Pride® cheese melters and salamanders are intended for use with the type of gas specified on the rating plate and for installation will be in accordance with National Fuel Gas Code ANSI Z223.1 (latest edition). Please retain this manual for future references. This equipment is design engineered for commercial use only. CAUTION Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. NOTICE Instructions to be followed in the event the user smells gas must be posted in a prominent location in the kitchen area. This information shall be obtained from the local gas supplier. WARNING FOR YOUR SAFETY: Do not store or use gasoline WARNING or other flammable vapors or liquids in the vicinity of this or any other appliance. California Residents Only WARNING: This product can expose you to chemicals including chromium which is known to WARNING the State of California to cause cancer and birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. IMPORTANT INSTRUCTIONS: After the gas supply has been connected to your unit, it is extremely important to check piping for possible leaks. To do this, use soap and water solution or solutions that are expressly made for this purpose. DO NOT USE matches, candles, flames, or other sources of ignition since these methods are extremely dangerous. Post in a prominent location instructions to be followed in the event you smell gas. Obtain these instructions from your local gas supplier. BAKERS PRIDE OVEN COMPANY, LLC. 1307 N. Watters Rd., Suite 180 Allen, TX 75013 Phone: 800.527.2100 | Fax: 914.576.0605 | bakerspride.com P/N 373712 REV A 4/19 RESTAURANT SERIES OPERATION MANUAL TABLE OF CONTENTS INSTALLATION INSTRUCTIONS 1 OPERATING INSTRUCTIONS 2 1 MAINTENANCE INSTRUCTIONS 4 WARRANTY 6 INSTALLATION INSTRUCTIONS • Installation of the equipment should be performed by qualified, certified, and authorized personnel who are familiar and experienced with local installation codes. • Before Installation please read instructions completely and carefully. • Do not remove permanently affixed labels, warnings or plates from the product. • Installation must conform with local codes, or in the absence of local codes, the National Fuel Gas Code, ANS1 Z223.1 (latest edition). In Canada, installation should conform to installation codes for gas burning appliances and equipment standard CAN/ CGA-B149.1 or the Propane installation code, CAN/ CGA-B149.2, as applicable. • Electrical wiring to the appliance must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Shipping Damage Claim Procedure The equipment is inspected and crated carefully Code ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2, as applicable. by skilled personnel before leaving our factory. • A manual gas shut-off valve must be installed in The transportation company assumes full the gas supply line ahead of the appliance and gas responsibility for safe delivery upon acceptance of pressure regulator for safety and ease in servicing. this equipment. If shipment arrives damaged: • The gas pressure regulator supplied must be installed 1. Visible loss or damage: Note on freight bill or on the appliance prior to connecting the equipment express delivery and signed by person making to the gas line. Failure to install a regulator could delivery. be potentially hazardous and will void the appliance 2. File claim for damages immediately: warranty. Regardless of extent of damages. • The appliance and its individual shut off valve must 3. Concealed loss or damage: If damage is noticed after unpacking, notify Transportation Company immediately and file “Concealed be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.45kpa). Damage” claim with the transportation carrier. • The appliance must be Isolated from gas supply This should be done within fifteen (15) days piping system, by closing its individual manual shut from the date delivery and receipt of goods. off valve during any pressure testing of the gas supply Retain container for inspection. piping system at test pressures equal to or less than 1/2 psi (3.45kpa) • Please observe all local and national codes and ordinances RESTAURANT SERIES OPERATION MANUAL 2 OPERATING INSTRUCTIONS Operating Instructions Rating Plate Operation of this equipment must be performed by Information on this plate includes the model, serial qualified or authorized personnel who have read and are number, BTU / hour input of the burners, operating familiar with the functions of the equipment. gas pressure in inches WC, and whether the appliance is orificed for natural or propane gas. When Maintenance communicating with factory about a unit or requesting To perform maintenance and repairs of the appliance, please contact the factory, the factory representative, or for special parts or information, rating plate data is essential for proper identification. the nearest authorized local service company. CAUTION Appliances must be connected only to the type of gas identified on the rating plate. Clearances The appliance area must be kept free and clear of all combustibles. Equipment Bakers Pride Model Combustible Non-Combustible Rear Sides Rear Sides Manual Griddle BPMG-C 8” 10” 0” 0” Thermostatic Griddle BPTG-C 8” 10” 0” 0” Radiant Char Broiler BPRB-C N/A N/A 0” 0” Hot Plate BPHP-C 8” 10” 0” 0” Stock Pot Range BPSP-C 17” 15” 0” 0” Lava Rock Char Broiler BPEB-C 8” 10” 0” 0” Cheese Melter BPCM 4” 4” 0” 0” Salamander BPSB 4” 4” 0” 0” Air Supply And Ventilation The area in front of, around and above the appliance must be kept clear to avoid any obstruction of the flow of combustion and ventilation air. Adequate clearance must be maintained around the appliance for easy servicing. Provision should be made for any commercial, heavy duty cooking appliance exhaust combustion waste products to the outside of the building. Usual practice is to place the appliance under an exhaust hood, which should be constructed in accordance to the local codes. Strong exhaust fans in this hood or in the overall air conditioning system can produce a slight vacuum in the room and / or cause air drafts, either of which can interfere with the pilot or burner performance and could be difficult to diagnose. Air movement should be checked during installation. Air openings or baffles may have to be provided in the room, if pilot or burner outage problem persists. Gas Connection The gas supply (service) line must be the same size or greater than the inlet line of the appliance. Appliances use a 3/4” NPT inlet. Sealant on all pipe joints must be resistive to LP gas. Manual Shut Off Valve This installer supplied valve must be in the gas service line ahead of the appliance regulator in the gas stream and in a position accessible in the event of an emergency. RESTAURANT SERIES OPERATION MANUAL OPERATING INSTRUCTIONS Pressure Regulator the factory, effectively matching them to sea level Commercial cooking equipment must have a pressure regulator on the incoming service line for safe and efficient operation, since service pressures may fluctuate on local demand. A pressure regulator is packed inside every gas appliance. 3 conditions. Adjustments and calibrations to assure proper operation may be necessary on installation to meet local conditions, low gas characteristics; correct possible problems caused by rough handling or vibration during shipment and are to be performed only by qualified service personnel. These adjustments are the NOTICE responsibility of the customer and / or dealer and are not covered by our warranty. Failure to install the pressure regulator will void Check all gas connections for leaks with a soapy water the appliance warranty. solution before lighting any pilots. The regulators supplied will have 3/4” inlet/outlet openings and are adjusted at the factory for 5” WC Lighting & Shutdown • Turn all valves to OFF position. (natural gas) or 10” WC (propane gas) depending on • Wait for 5 minutes. customer’s ordering instructions. Prior to connecting the regulator, check the incoming line pressure, as these regulators can only withstand a maximum pressure of 1/2’’ psi (14” WC). If the line pressure is beyond this • Turn pilot valve(s) adjusting screw counter clockwise, then light standing pilot and adjust flame 1/4 inch high. limit, a step-down regulator will be required. • Turn ON gas valve(s) to light main burner. The arrow shown on the bottom of the regulator body • For complete shutdown, shut OFF gas valve(s) and shows the gas flow direction, it should point downstream turn pilot valve(s) adjusting screw clockwise to shut to the appliance. The red air vent cap on the top is part off gas to the pilot(s). of the regulator and should not be removed. Before First Use Any adjustments to the regulator should be made by qualified service personnel only with the proper equipment. • Clean the griddle surface thoroughly with hot, soapy water to remove factory applied protective oil coating. Connections • Rinse with a mixture of 1/4 cup vinegar to one quart Please check installer supplied intake pipes visually water. and / or blow them with compressed air to clear any • Spread unsalted solid shortening or liquid frying dirt particles, threading chips or any other foreign compound evenly over the entire griddle surface. matter before installing a service line. When gas pressure is applied, these particles could clog orifices. All connections must be sealed with a joint compound suitable for LP gas, and all connections must be tested • Turn all griddle burners to medium and wait until the shortening begins to smoke, then turn the burners OFF. with a soapy water solution before lighting any pilots. • Rub the now melted shortening into the griddle Initial Pilot Lighting surface with burlap, moving in the direction of the surface’s polish marks and covering the entire All appliances are adjusted and tested before leaving surface. • Allow the griddle to cool. When lighting pilots and checking for leaks, do not stand with your face close to the combustion • When the griddle is cool after the second seasoning, wipe it with a thin film of shortening or cooking oil. chamber. CAUTION RESTAURANT SERIES OPERATION MANUAL MAINTENANCE INSTRUCTIONS Cleaning & Maintenance Stainless Steel Any equipment works better and lasts longer when All Stainless Steel body parts should be wiped regularly maintained properly. Cooking equipment is no with hot soapy water during the day and with a liquid exception. Your appliance must be kept clean too on a cleaner designed for this material at the end of each daily basis. day. DO NOT USE steel wool, abrasive cloth, or powders Daily Maintenance to clean Stainless surfaces. If it is necessary to scrape Stainless steel to remove encrusted materials, soak in Open Burners hot water to loosen the material, then use a wood or 1. Remove all top grates. nylon scraper. DO NOT USE a metal knife, spatula, or any other metal tool to scrape Stainless Steel. Scratches 2. Lift off the burner heads and venturies by raising are almost impossible to remove. the head slightly, sliding to the rear of the range and lifting upwards. • Wash with hot, soapy water, then rinse with vinegar 3. Wash off the above in hot soapy water. and water. 4. Re-install burner parts in the reverse order. • Rinse again with clear water. Griddles • Re-oil with shortening or liquid frying compound. 1. Scrape with a nylon griddle scraper to remove the • DO NOT FLOOD A HOT GRIDDLE WITH COLD cooked spills. When absolutely necessary use a WATER. This could cause warping and griddle plate fine-grained stone to scrape. to crack. 2. Wipe away any griddle stone dust and food particles with burlap. Ovens • Remove the baking racks. Wash in hot soapy water, 3. Wash with hot, soapy water, then rinse with vinegar and replace after the oven is fully cleaned. and water. 4. Rinse again with clear water. • Remove the oven bottom by lifting it out from the front, then sliding forward, out of the oven. 5. Re-oil with shortening or liquid frying compound. • Scrape off any food particles with a nylon griddle 6. DO NOT FLOOD A HOT GRIDDLE WITH COLD scrapper. Be very careful about scratching the WATER. This could cause warping and griddle plate porcelain finish on the oven liner panels. to crack. • Wash all the above with hot soapy water, then reassemble. • Baked on spills may be loosened and stubborn stains removed with ordinary household ammonia and scrubbing with a nylon pad in a cold oven only. • Do not allow spray type oven cleaners to come into contact with the temperature probe in the oven. • After cleaning the oven, rinse well with 1/4 cup of vinegar to one quart of clean water solution to neutralize any caustic residue of the cleaning compound. Wipe dry. 4 RESTAURANT SERIES OPERATION MANUAL MAINTENANCE INSTRUCTIONS Periodic Cleaning Check the ventilation system periodically to see that nothing has fallen down into the stub back, high riser or high shelf exhaust vents. Lubricate the pivot pins of the WARNING Contact the factory, factory representative or a local service company to perform all Maintenance and Service Repairs.oven door hinge where the right and left arms connect to the door. Use lubricating oil. Ensure your appliance is checked by a qualified technician once a year for efficient operation of the appliance. Stainless Steel All stainless steel body parts should be wiped regularly with hot soapy water during the day and with a liquid cleaner designed for this material at the end of each day. DO NOT USE steel wool, abrasive cloth, or powders to clean stainless surfaces. If it is necessary to scrape stainless steel to remove encrusted materials, soak in hot water to loosen the material, then use a wood or nylon scraper. DO NOT USE a metal knife, spatula, or any other metal tool to scrape stainless steel. Scratches are almost impossible to remove. 5 RESTAURANT SERIES OPERATION MANUAL BAKERS PRIDE LIMITED WARRANTY WHAT IS COVERED This warranty covers defects in material and workmanship under normal use, and applies only to the original purchaser providing that: • The equipment has not been accidentally or intentionally damaged, altered or misused; • The equipment is properly installed, adjusted, operated and maintained in accordance with National and local codes and in accordance with the installation instruction provided with the product; • The serial number rating plate affixed to the equipment has not been defaced or removed. WHO IS COVERED This warranty is extended to the original purchaser and applies only to equipment purchased for use in the U.S.A. COVERAGE PERIOD Cyclone Convection Ovens: BCO Models: One (1) Year limited parts and labor; (1) Year limited door warranty. GDCO Models: Two (2) Year limited parts and labor; (2) Year limited door warranty. CO11 Models: Two (2) Year limited parts and labor; (5) Year limited door warranty. All Other Products: One (1) Year limited parts and labor. Warranty period begins the date of dealer invoice to customer or ninety (90) days after shipment date from Bakers Pride - whichever comes first. WARRANTY This warranty covers on-site labor, parts and reasonable travel time and travel expenses of the authorized service COVERAGE Representative up to (100) miles, round trip, and (2) hours travel time. The purchaser, however, shall be responsible for all expenses related to travel, including time, mileage and shipping expenses on smaller counter models that may be carried into a Factory Authorized Service Center, including the following models: PX-14, PX-16, P18, P22S, P24S, PD-4, PDC, WS Series and BK-18. EXCEPTIONS All removable parts in Bakers Pride® commercial cooking equipment, including but not limited to: Burners, Grates, Radiants, Stones and Valves, are covered for a period of SIX MONTHS. All Ceramic Baking Decks are covered for a period of THREE MONTHS. The installation of these replacement decks is the responsibility of the purchaser. The extended Cyclone door warranty years 3 through 5 is a parts only warranty and does not include labor, travel, mileage or any other charges.

EXCLUSIONS 6 • Negligence or acts of God, • Failures caused by erratic voltages or gas supplies, • Thermostats and safety valves with broken capillary tubes, • Thermostats and safety valves with broken capillary tubes, • Thermostat calibrations after (30) days from equipment installation date, • Unauthorized repair by anyone other than a Bakers Pride Factory Authorized Service Center, • Air and Gas adjustments, • Damage in shipment, • Light bulbs, • Alteration, misuse or improper installation, • Glass doors and door adjustments, • Fuses, • Char-broiler work decks and cutting boards, • Tightening of conveyor chains, • Adjustments to burner flames and cleaning of pilot burners, • Tightening of screws or fasteners, • Accessories — spatulas, forks, steak turners, grate lifters, oven brushes, scrapers, peels. etc., • Freight — other than normal UPS charges, • Ordinary wear and tear.

INSTALLATION Leveling and installation of decks as well as proper installation and check out of all new equipment —per appropriate installation and use materials — is the responsibility of the dealer or installer, not the manufacturer. REPLACEMENT PARTS Bakers Pride genuine Factory OEM parts receive a (90) day materials warranty effective from the date of installation by a Bakers Pride Factory Authorized Service Center. This Warranty is in lieu of all other warranties, expressed or implied, and all other obligations or liabilities on the manufacturer’s part. Bakers Pride shall in no event be liable for any special, indirect or consequential damages, or in any event for damages in excess of the purchase price of the unit. The repair or replacement of proven defective parts shall constitute a fulfillment of all obligations under the terms of this warranty. Form #U4177A 1/07 NOTES IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or Parts, this information is required. Model Number Serial Number Date Purchased 7 1307 N. Watters Rd, Ste. 180 Allen,Texas 75013 Phone 800.527.2100 | Fax 914.576.0605 | bakerspride.com Be sure to keep up with new product announcements and events on social media! Social iconSquare Only use blue and/or white.For more details check out our Brand Guidelines. 4.15.2019


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply