Post questions, comments, reviews or errors in the comment box below.
Your File is Ready … Download PDF
PDF Content Summary: HD90 QUICK START GUIDE About this Guide This guide is a quick reference for users to install and operate HD90 Night Vision HD Indoor/Outdoor Bullet Cameras. It provides only basic information regarding HD90 camera models. For further details on installation and operation, please refer to the User Manual. The HD90 Camera User Manual can be found on the included CD and at avertx.com CONTENTS Before proceeding, please check to confirm that the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact AvertX for assistance. HD90 Bullet Camera Hex Head Wrench Screws Anchors Quick Start Guide & Installation CD INSTALLATION All HD90 cameras can be installed directly onto a wall or ceiling. Be sure that the structure is strong enough to support the camera. 1. If passing the cord through a wall or ceiling, drill a 3/4” hole. 2. Connect the Ethernet cable to the dongle Remove Packaging on the camera. • Protect the network cable connection from water damage by running the cord inside a wall or ceiling, or through conduit. • For outdoor installations, seal any holes in the wall or ceiling with silicone Align Holes on Wall caulk to protect against water intrusion. 3. Affix the mounting bracket to the ceiling or wall with the included self-tapping screws and wall anchors. 4. Use the included hex-head wrench to loosen the bolt on the side of the bracket mount and on the camera housing. 5. Adjust the position of your camera. 6. Tighten the bolts to secure your camera. Adjust Aim 31629AC MICRO SD CARD NETWORK CABLE INSTALLATION & RESET BUTTON When installing your AvertX Night Vision HD Indoor/Outdoor Bullet Camera, it is important to consider how the network cable attached to the camera is arranged. Copyright © 2014 AvertX. All rights reserved. Information contained in this document is subject to change without prior notice. AvertX does its best to provide accurate information, but cannot be held responsible for typos or mistakes. Reset button • Your HD90 camera includes a Micro SD card slot (up to 16GB), which can be used for emergency video backup. Micro SD card is not included. • Protect the network cable connection from water damage by running the cord inside a wall or ceiling, or through conduit. • Press the reset button for 30 seconds to • If passing the cord through a wall or ceiling, drill a 3/4”” hole. return the camera to factory default settings, if • For outdoor installations, seal any holes in the wall or ceiling with silicone caulk to necessary. protect against water intrusion. • You must remove the cover of the HD90 camera to access the Micro SD card slot and the Reset button. Micro SD card slot FOCUSING THE CAMERA CONNECTING TO THE CAMERA For optimal image quality, you may need to manually focus your AvertX camera after If you are using this camera with an AvertX recorder, follow the instructions in the it has been installed. This card provides instructions for focusing your AvertX HD90 HDIP recorder user manual to connect to your camera. You can also set up your Night Vision HD Indoor/Outdoor Bullet Camera. camera over your network using an internet browser. Type the IP address of the 1. Remove the screw at the bottom of the 6. Tighten the set screw. camera in the address bar of your internet browser to connect to the camera. front lens cover. 7. Replace the rubber gasket. 2. Remove the front lens cover by gently tilting it up from the bottom. 8. Align the positioning pin at the top of the lens cover with the hole on the camera 3. Remove the rubber gasket. body and replace the cover. 4. Loosen the set screw. 5. Turn the lens to focus your camera. Set screw Remove lens cover 1-855-2avertX (1-855-228-3789) http://www.avertx.com 31629AC If your internet browser doesn’t install the camera viewer software, check the security settings or ActiveX controls and plug-in settings. If your internet browser asks for permission to install the ActiveX control, you must allow the ActiveX control to continue the installation. 9. Replace the screw at the bottom of the front lens cover. Default IP address: Tilt lens cover up to remove 192.168.0.250 User Name and Password: The username and password are case sensitive. AvertX strongly recommends chang- ing the password after the initial setup to prevent unauthorized access to the camera. Username – Admin Password – 1234 Screw Turn lens Remove to focus gasket
FREE ENGLISH PDF
USER GUIDE - USER MANUAL
OWNER GUIDE - OWNER MANUAL
REFERENCE GUIDE - REFERENCE MANUAL
INSTRUCTION GUIDE - INSTRUCTION MANUAL