AVALLON AFR152SSODLH (01) PDF Document

To reduce the risk of fire, electric shock, or injury when using your AVALLON AFR152SSODLH, please read and follow this safety information:

• Do not exceed the power outlet ratings.

• It is recommended the refrigerator be connected on its own circuit.

• The unit must be installed in accordance with state and local electrical codes.

• A standard electrical supply (115 V, 60Hz), that is properly grounded in accordance with the National Electrical Code and local codes and ordinances is required.

• Use outlets that cannot be turned off by a switch or pull chain.

• Always turn the unit off and unplug it from the outlet when cleaning.

• Unplug the unit if it is not going to be used for an extended period of time.

• Do not operate the unit with a power plug missing the ground plug, a damaged cord, or a loose socket.

• Be sure the refrigerator is properly grounded.

• Never plug or unplug the unit with wet hands.

• Do not bypass, cut, or remove the grounding plug.

• Do not use extension cords or power strips with this unit. You may need to contact your electrician if it is necessary to use a longer cord or if you do not have a grounded outlet. Do not modify the power cord’s length or share the outlet with other appliances.

• Do not start or stop the unit by switching the circuit’s power on and off.

• If the power cord is damaged, it must be replaced by the manufacturer or a qualified technician.

• Never repair the unit while it is plugged in.

• Immediately unplug the unit if it makes strange sounds, emits smells, or smoke comes out of it, and contact customer service.

• Do not remove any part of the casing unless you are instructed to do so by an authorized technician.

• You should never attempt to repair the unit yourself.

• To prevent injuries, use at least two people to move and install the refrigerator.

• This appliance is not intended for use by persons, including children, with reduced physical, sensory or mental capabilities, unless they have been given supervision or instruction concerning the use of the appliance by the person(s) responsible for their safety.

• Install the refrigerator in a well-ventilated area where the ambient temperature is above 50° F and below 90° F.

• The temperature range for this refrigerator is optimized for perishable food items.

• Do not place hot or warm items into the refrigerator before they cool down to room temperature.

• This unit is not intended to be used by children.

• Children should be supervised to ensure that they do not play with this product.

• Never allow children to crawl inside the refrigerator. If you are disposing of the unit, remove the door.

• Do not use this appliance near flammable gas or combustibles such as gasoline, benzene, or thinner.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

• Do not place the unit near heat sources such as ovens, grills, or direct sunlight.

• Only use in an upright position on a flat, level surface and provide proper ventilation.

• Do not pinch or kink the power supply line between the unit and cabinet.

• Do not leave any cleaning solutions in the unit.

• Do not use solvent-based cleaning agents or abrasive solutions to clean the unit as they may damage the interior and exterior.

• Do not place any other appliances on top of the unit.

• Do not turn the unit upside down, on its side, or at an angle off level.

• If your model of refrigerator is equipped with a lock, keep the keys away from children.

• Do not move the unit without emptying the contents and securing the door in a closed position.

• This appliance is meant for use in the household or outdoors.

• Keep all ventilation openings clear of obstruction.

• Do not use mechanical devices or other means to accelerate the defrosting process.

• Do not damage the refrigerant circuit.

• Do not use other appliances inside the refrigerator unless recommended by the manufacturer.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified individual.

Warning: Flammable Refrigerant Used! When handling, moving, and using the refrigerator, make sure to avoid either damaging the refrigerant tubing or increasing the risk of a leak.

Warning: Risk of child entrapment. Before you throw away your old refrigerator or freezer, take off the doors and leave the shelves in place so that children may not easily climb inside.

Before use, make sure all packaging labels and materials are removed from the unit. Be sure to keep track of all included parts and pieces before discarding the packaging materials. It is advised that you keep the original box and packaging materials in case you ever need to move or ship the appliance in the future.

Let the unit stand for at least 24 hours before you use it; this allows the cooling components time to settle from transit. The instruction manual should be read before use.

1. Have all packing materials and tape been removed from the interior and exterior of the refrigerator?

2. Have the installation instructions been followed, including connecting the machine to electricity? And has proper grounding been installed for the refrigerator?

3. Has the machine been leveled?

4. Is the refrigerator in a site where the ambient temperature is between 50° F and 90° F all year round?

5. Is there a clearance of at least 1- 2” at the rear, 1/4” at the top, and 1/4” at the sides for proper air circulation?

The main parts of the AVALLON AFR152SSODLH are:

Open View:

• Control Panel

• Carbon Filter

• Internal Fan

• Shelf

• Door Rack

Closed View:

• Stainless Door

• Handle

• Front Vent

• Door Lock

• Leveling Leg

Back View:

• Cabinet

• Rating Label

• Power Cord

The AVALLON AFR152SSODLH has a built-in carbon filter that protects your contents by acting as a natural barrier against harmful odors.

The carbon filter should be replaced every 3 – 6 months depending on the unit’s exposure level to odor. If the unit is placed in the kitchen, regular replacement every 3 months is ideal.

The AVALLON AFR152SSODLH is an air-cooled unit equipped with an internal fan that maintains a consistent internal temperature.

Warning: Use two or more people to move and install the refrigerator. Failure to do so can result in back or other injury. Carefully remove the packaging materials. Remove any shipping tape and glue from your refrigerator before use. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.

Also, do not remove any safety, warning, or product information labels from your refrigerator.

Yes, the AVALLON AFR152SSODLH has been designed for freestanding or built-in installation. In each case, there must be adequate ventilation and access for service.

Freestanding Installation:

A freestanding installation will allow you to install the refrigerator in almost any place you desire. You must follow the stated instructions for electrical requirements and leveling the refrigerator.

Built-in Installation:

A built-in installation will allow you to install the refrigerator under a counter as long as the required clearance space around the refrigerator is provided. It is necessary to allow adequate ventilation space around the unit, including at the back of the unit.

The following additional items must be observed:

1. Place the refrigerator in front of the installation location. Adjust the feet and place the unit flat on the floor or on a platform depending on your installation requirements.

2. If the electrical outlet for the refrigerator is behind the cabinet, plug in the refrigerator.

3. Push the refrigerator into position.

Warning: DO NOT install the refrigerator behind a closed cabinet door.

When installing the refrigerator under a counter, follow the recommended spacing dimensions shown.

To ensure proper service access and ventilation, allow at least 1-2” of clearance at the back, 1/4” at the top, and 1/4” at the sides. If the door side is against a wall, allow at least 2 1/16” of clearance. The installation should allow the unit to be pulled forward for servicing, if necessary.

Electrical Requirements:

• A standard electrical supply (115 V, 60Hz), properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required.

• It is recommended that a separate circuit, serving only your refrigerator, be provided. Use receptacles that cannot be turned off by a switch or pull chain.

• The fuse (or circuit breaker) size should be 15 Amps.

Recommended Grounding Method:

For your personal safety, this appliance must be grounded. It is equipped with a power supply cord that has a 3-pronged grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-pronged wall socket, and grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall socket is not available, it is the personal responsibility of the customer to have a properly grounded, 3-prong wall receptacle installed by a qualified electrician.

The refrigerator should be installed on a firm and level surface that will be able to support the entire weight of a fully loaded unit. It is important for the refrigerator to be leveled in order to work properly. It can be raised or lowered by rotating the plastic sheaths around each of the feet on the bottom of the machine. If you find that the surface is not level, rotate the feet until the refrigerator becomes level. You may need to make several adjustments to level it. We recommend using a carpenter’s level to check the machine. Turn the leveling feet to the right to lower that side of the refrigerator. Turn the leveling feet to the left to raise that side of the refrigerator.

Important: Once you are ready to install the unit in a cabinet or directly on the floor, you must adjust the feet to level the refrigerator.

To install the door handle:

1. Open the door and carefully pull the door gasket around the area where the handle is to be installed.

2. Insert each Phillips head screw through the gasket side of the door until the screw passes through the door.

3. Align the handle with the screws and tighten using a Phillips head screwdriver until the handle is flush against the door frame.

4. Carefully press the door gasket into its original position.

Caution: Do not over-tighten the screws as this may cause damage to the handle or to the stainless steel door.

This unit comes with four (4) casters. These are an optional accessory to assemble if you would like to make the unit more mobile. To install the casters:

1. Carefully lower the refrigerator onto a soft surface such as a blanket.

2. Separate the front casters and back casters. The front casters have a lever for a brake lock.

3. Place the top plate of the caster over the area of the removed leveling leg and align the opening to the screw hole openings.

4. Insert the screws to attach the caster to the cabinet.

5. Make sure the screws are tight so the caster is installed firmly.

To prevent damaging the door gasket, make sure to open the door fully before pulling the shelves off their tracks.

1. Open the door completely.

2. Ensure that the metal guide posts are attached to the back of the shelf.

3. While lifting the right side of the shelf up 45°, rest the left metal guide post on the shelf track.

4. Slowly push the shelf back until the right metal guide post reaches the vertical indentation in the cabinet.

5. Gently set the shelf down on the track.

1. Open the door completely.

2. Remove all of the contents loaded on the shelf, if applicable.

3. Ensure that the shelf is pushed back completely.

4. Carefully lift either the left or right side of the shelf up 45°.

5. Pull the shelf forward until it is completely removed from the inner compartment.

The control panel has the following functions:

• Power Button: Turns the unit on and off. Press and hold this button for approximately 3 seconds to adjust between power on and power off.

• Light Button: Press this button to alternate between the three internal light colors: Blue, white, and amber.

• Up Button: Press this button on the control panel to increase the temperature by 1 degree increments.

• Down Button: Press this button on the control panel to lower the temperature by 1 degree increments.

• Run Light: When lit, the unit is in cooling mode.

• Celsius (C) or Fahrenheit (F) indicator: This will be lit depending on which unit of temperature measurement is being used. To switch between C and F, press and hold both the Up and Down buttons simultaneously for approximately 3 seconds. A beep will sound and the indicator light will illuminate next to the desired temperature setting.

The AVALLON AFR152SSODLH has a temperature range of 34° F to 65° F.

This refrigerator is programmed with a Sabbath Mode. In Sabbath Mode, the refrigerator will continue to cool and maintain temperature. However, the refrigerator will no longer respond to user interactions. All lights, display(s), and indicators are turned off, and all alarms are disabled.

To enter Sabbath Mode, hold the Power button and press the Up button twice. The control panel will beep twice indicating that the refrigerator is in Sabbath Mode.

To exit Sabbath Mode, perform the same action and the control panel will beep twice indicating that the refrigerator is no longer in Sabbath mode. The refrigerator will return to normal operation.

This refrigerator is equipped with top and side internal lights that can be set to a blue, white, or amber color. The internal lights will illuminate each time the door is opened and fade off once the door is closed. This feature is triggered by a sensor located on the front vent. This sensor allows the refrigerator to recognize when the door is open or closed.

Note: We run test every unit that we produce in our factory. Because of this, your model may default to any of the above colors out of the box. Simply cycle through until you reach your desired internal light color.

Your new refrigerator may make noise during normal operation. Most of these sounds are normal. Hard surfaces like the floor and walls can make the sounds seem louder than they actually are.

The following describes several sounds you may hear and what may be making them:

• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the refrigerator can also make noises.

• The high efficiency compressor may make a pulsating or high-pitched sound.

• Water running from the evaporator to the water bin may make a splashing sound.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.

• You may hear air being forced over the condenser by the condenser fan.

If the interior temperature is higher than 73°F (23°C), “HI” is shown on the temperature control panel and the temperature alarm will sound continuously after one (1) hour. This indicates that the inner temperature is too high. If the inner temperature is lower than 25°F (-4°C), “LO” is shown on the temperature display panel and the temperature alarm will sound continuously after fifteen minutes. If one of these situations occurs please reference the troubleshooting section found in the manual.

This refrigerator includes a door ajar alarm, which will sound if the door is open for more than three (3) minutes. Leaving the door open for extended periods of time will cause poor cooling performance and may shorten the life of the refrigerator. Keep the doors closed as much as possible.

Under most refrigerating settings, the unit will automatically defrost under most ambient conditions. However, on colder settings, some frost may build up. Additionally, the more humid the ambient conditions, the more frost may build up. Keep the door closed as much as possible and avoid opening the door unnecessarily to minimize frost build-up.

If frost is preventing the door from closing properly, you may need to power the unit off until the frost melts. Use a soft absorbent towel to dry the unit.

Warning: Never attempt to remove frost with a sharp object!

If the refrigerator will not be used for a long time, or is to be moved to another place, it will be necessary to defrost the unit and dry the interior.

1. Disconnect the refrigerator from the power supply by removing the power plug from the wall socket.

2. Leave the door open to allow for air circulation and to prevent mold, mildew, and unpleasant smells.

3. Once the interior is dry and clean the unit will be ready for storage.

Caution: Store the unit out of reach from children. If you have children, you may want to take additional precautions such as removing the door to prevent a child from being trapped inside the refrigerator.

Exterior Cleaning

The door and cabinet may be cleaned with a mild detergent and lukewarm water solution such as 2 tablespoons of baking soda to 1 quart of water.

Do not use solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean towel to prevent water spotting. If the door panel is stainless steel, it can discolor when exposed to chlorine gas and moisture. Clean stainless steel using a cloth dampened with a mild detergent and warm water solution. Never use an abrasive or caustic cleaning agent.

Interior Cleaning

The refrigerator’s interior should be cleaned occasionally.

1. Disconnect power to the unit.

2. Open the door and remove the contents and shelves.

3. Wait until the unit defrosts.

4. With a clean cloth, wipe down the interior of the unit.

5. Reinsert the shelves and contents.

6. Reconnect power to the unit.

Technical data and performance information are provided for reference only. Specifications are subject to change. Check the rating label on the refrigerator for the most accurate information.

Note: Depth shown includes the handle. Depth without the handle is 23 5/8”.

If the unit appears to be malfunctioning, read through the “Operation” section of the manual first. If the problem persists, check the Troubleshooting Guide.