Click here to download AUDIOVOX FRS-1000 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** AUDIOVOXN CORPORATION FRS/Weather Model: FRS-I OOO Base Station With NOAA Weather Alert Owner’s Manual Mufti Radio Station FRS•WFWHFR r CHIVOL -1 For Customer Service Visit Our Website At audiovox.com Product Information, Photos, FAQs, Owners Manuals AUDIOVOX Hauppauge, Customer Service/Service 1-800-290-6650 NY 11788 0 2001 Audiovox Electronics Corp. Printed in Korea 128-6032

****** Page 2 ****** CAUTION NEVER ATTEMPT TO CHARGE ALKALINE OR DRY CELL BATTERIES. WHEN RECHARGING, USE ONLY THE RECHARGEABLE BATTERIES SUPPLIED WITH YOUR TRANSCEIVER. USE OF OTHER BATTERIES WILL CAUSE DAMAGE TO YOUR FRS-IOOO WEATHER RADIO TRANS- CEIVER. OTHER TYPES OF BATTERIES MAY BURST CAUSING PER- SONAL INJURY. AVOID INSTALLING THE FRS-IOOO TRANSCEIVER IN AN AREA WHERE IT MAY BE SUBJECTED FOR PROLONGED PERIODS OF TIME TO Dl- RECT SUNLIGHT OR TEMPERATURES BELOW -40 F (-200 C) OR ABOVE 140 0 F (600 C). KEEP THE ANTENNA AT LEAST 1 INCH (2.5 cm) AWAY FROM YOUR HEAD AND BODY. DO NOT USE YOUR FRS-IOOO RADIO TRANS- CEIVER WITH A DAMAGED ANTENNA. Family Radio Service: The Family Radio Service (FRS) 2-way base (fixed) station “transceiver” (“transmitter and receiver”) radio has been designed for family and friends to keep in touch without the need for a license. It provides safety and convenience indoors for two-way radio operation between home base and other mobile FRS units, and operates on Family Radio Service designated frequencies. The FCC has established the license free, short -range two- way radio service for family and individual recreational use. The optimal range for this 2-way radio is approximately 2 miles in open areas; less in areas with buildings, dense foliage, and mountains. 2

****** Page 3 ****** Model FRS-IOOO 1 2 3 4 5 6 7 8 9 10 11 12 1. Battery CHARGE On/Off Switch 2. Liquid Crystal Display (LCD) 3. Alert (ALT) LED (Red) 4. Antenna (Retractable) 5. Transmit LED (Green) 6. Battery Door 7. Voice-Operated Transmission (VOX) Button 8. Weather/FRS Button 9. SCAN/Lock Button 10. Built-in Speaker 11. Built-in Microphone 13 14 15 16 17 18 19 20 21 ACDIO’OX 12. CALL Button 13. 15. 16. 18. 19. 20. 21. 3 DC12V Power Jack 14. Charging (CHG.) LED (Red) Up/Down Channel/Volume Buttons Weather Alert Button 17. MODE Button LCD Backlight/Monitor (LIMON) Button Power On/Off and Function Set Button External Speaker(SPK)/Micro- phone (MIC) Jacks Push-To-Talk (PTT) Button

****** Page 4 ****** Model FRS-IOOO DISPLAY 1 2 3 4 5 6 7 HI LO ooo CAN VOX 8 9 10 11 12 13 14 1. 2. 3. 4. 5. 6. 7. 8. 9. Button (Key) Tone Beep On/Off Indicator: This icon appears when the beep key tone is on, and disappears when tone is not in use. Key Lock Indicator: Icon appears when keypad is locked. This function disables keys such as channel up/down and MODE. Monitor Indicator: Icon appears when the Monitor (LIMON) button is pressed and the channel monitor function is activated. Signal Strength Indicator: Icon appears when a signal is being received. The icon consists of five bars to indicate the received signal level. The icon also represents transmit signal power when transmitting. Continuous Tone Coded Squelch System (CTCSS) Indicator: Icon appears when the CTCSS tone function is active. Large Segment Display: Indicates the FRS channel number in use. Scan Indicator: This function allows the user to scan a channel and/or a tone code every .5 second to search for a valid signal Battery Level Indicator: Icon indicates the battery charge level. HI/LO Indicators: Appropriate icon appears when the transmit power is set to desired output power. 4

****** Page 5 ****** 10. 11. 12. 13. 14. Weather Mode Indicator: Icon appears steady when weather mode is active; it flashes when weather alert is active in the FRS mode. Roger Beep Tone Indicator: Icon appears when the roger beep tone is enabled, signifying transmission has been terminated. Icon disappears when tone is disabled. Small Segment Display: Displays the CTCSS tone option for a given channel from (01-38). Dual Watch Mode Indicator: Icon appears when dual watch mode is active. Voice Activated Transmission (VOX) Indicator: This function allows hands-free conversation. The icon appears when the VOX mode is activated. Powering the transceiver: The primary power source for Your FRS-IOOO base station is the AC wall adapter. The FRS-1000 is also supplied with a battery back-up, should you experience loss of household current. The FRS-1000 will automatically switch to battery back-up when AC power is interrupted. The rechargeable batteries, Part Number FRSRBAT, are charged in the radio transceiver using the AC power adapter, which is also supplied with the unit. Installing the Back-Up Batteries: The four AA batteries are installed in the compartment at the right rear of the transceiver; the compartment is fitted with a removable cover. Install the batteries as follows: 1 . Press down with the thumb at the arrow, and slide the battery cover off the side of the unit. 2. Insert the four AA rechargable batteries, Part Number FRSRBAT, provided. (Alternate positive ends (+) as shown in battery compartment layout.) Replace the cover. 5

****** Page 6 ****** BATTERY INSTALLATION POLARITY -c -c BATTERY COMPARTMENT COVER BATTERY COMPARTMENT COVER ARROW The following guidelines will improve performance and provide longer operating times for the FRS-1000: 1 2. 3. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (Ni-MH)batteries. If the unit is not to be used for an extended period of time, remove the batteries. Old or leaking batteries can cause damage to the unit and will void the warranty. Charging FRS-IOOO Batteries PIN FRSRBAT: The rechargeable batteries, Part Number FRSRBAT, supplied with the unit, are charged by connecting the AC Adapter plug to the DC12V jack on the top of the unit, and setting the CHARGE switch to the ON position. Use only the AC Wall Adapter, Part Number FRSI -AD, that is supplied with the base unit. The CHG. LED indicator below the LCD display lights red during battery charge operation. 6

****** Page 7 ****** The battery charge indicator icon displays the battery charge level when the AC adpter is unplugged. When the AC adapter is connected and in use, the indicator icon will indicate a full charge as shown below. Full Battery – three segments are illuminated. Low Battery – one segment is illuminated. Approximately 20—24 hours are required to fully charge the batteries. The red LED charging indicator (14) will light whenever the batteries are charging. A flashing red LED charging indicator denotes batteries are not installed. You must set the CHARGE switch to the OFF position, when using any batteries other than the ones provided. Failure to do this may cause damage to batteries resulting in personal injury and/or damage to the unit. Caution: The charging adapter is intended for use with the supplied rechargeable Ni-MH batteries Part Number FRSRBAT. Do not attempt to recharge any other type batteries. AC ADAPTER CHARGE ONIOFF SWITCH ADAPTER PLUG DC12V JACK BASE UNIT 7

****** Page 8 ****** FRS-IOOO OPERATIONAL MODES WEATHER BAND CHANNEL SELECT (WX/MODE/CH) BUTTON BEEP (WX/MODE,MODE/ On/0F) NOTE: FRS BAND CHANNEL SELECT CTCSS SELECT POWER SELECT DUAL WATCH KEY TONE ROGER BEEP CALL SELECT To switch between FRS and Weather Band modes, momentarily press the FRS/WX button. To differentiate between operating modesi look for HI or LO indication below the battery power level indicator when in FRS mode. In Weather Band mode, these indications are not present. Refer to the appropriate section of this manual for detailed operating instructions for each mode. 8

****** Page 9 ****** Controls: Power On/Off (19) Button Press and hold the power on/off button (Ö ) for at least 2 seconds. You will hear a confirming melody to indicate the unit is on. To turn the unit off, press and hold the button for at least 2 seconds. Adjusting the Volume With the unit powered on, press the Up Channel/Volume button ( A) to increase volume and the Down Channel/Volume button ( V ) to decrease volume. The display will indicate the current volume level by the small number adjacent to the icon( LIL ) Monitor/Display (UMON) Button (18) This button is used to to check activity on the current frequency before transmitting. Check activity by pressing the Monitor (LIMON) Button longer than 2 seconds; the icon will apppear on the display and you will hear static if frequency is clear. Do not transmit if you hear conversation. Hold down the LIMON Button again longer than 2 seconds and the icon will disapppear from the display. The monitor function will temporarily bypass the squelch setting and play all signals on a given channel. This feature is useful when comunicating with other parties at extreme range. By pressing the monitor button momentarily, the LCD backlight is turned on; the LCD backlight will turn off automatically in about 5 seconds, or when the LIMON button is pressed momentarily once again. Push To Talk (PTT) Button (21) Pressing and holding this button will allow you to speak to any transceiver that is set to the same channel and privacy code setting as yours. After you have finished speaking, release the PTT Button to allow reception of incoming signals. It is not possible to transmit and receive at the same time. The Transmit (TX) LED at the lower left corner below the LCD Panel (2) will light red while the PTT Button is pressed, and the signal strength indicator will display the relative strength of the transmitted signal. Releasing the button 9

****** Page 10 ****** allows the unit to revert to standby mode. When receiving an incoming signal, the received signal strength indicator ( ) will display the relative strength of the signal CALL Button (12) The CALL Button can also be used as a two-way call ringer. Pressing the button will call another party on the same channel. The Transmit LED will light red for approximately 3 seconds and then go out. Up Channel/Volume Button (15) In the FRS standby mode, pressing this button ( A ) will increment the listening volume. When in function edit mode, this button will be used to adjust the unit’s settings. Down Channel/Volume Button (15) In the FRS standby mode, pressing this button (Y ) will decrement the listening volume. When in function edit mode this button will be used to adjust the unit’s settings. Mode Button (17) In the FRS standby mode, pressing this button momentarily will enter the function edit mode. Subsequent presses will cycle to each mode. The MODE button is used to select various features for adjustment in both the FRS and weather modes. External Speaker (SPK)/Microphone (MIC) Jacks (20) This set of jacks accepts an Audiovox headset/microphone connector. Refer to FRS-IOOO Operational Modes. Scan/Lock Mode Button (9) Press this Button momentarily to enable or disable the scan mode. 10 Press

****** Page 11 ****** and hold Button for more than 1 second to lock or unlock keypad functions, except PTT and Monitor (LIMON). When the keypad is locked, the ( icon will appear in the upper right corner of the display. FRS Operation Channel Selection In order to communicate with other FRS units, both transmitting and re- ceiving party must be on the same frequency. The FRS-IOOO has 14 channels (frequencies 1-14) indicated by the large digits on the LCD display panel. Communication with Audiovox FRS and compatible units is possible on these 14 channels. Before transmitting on the selected channel, press the Monitor (LIMON) Button (18) to check the activity on that channel. If there is activity on the selected channel, change to another channel that is clear. To change the FRS channel, From FRS standby mode, press the MODE button (17) until the chan- nel number flashes. Press the Up Button ( A ) briefly to move to the next higher main channel number. – Press the Down Button ( V ) briefly to move to the next lower main channel number. Continuous Tone Coded Squelch System (CTCSS) Mode (Sub- Channel) Selection The Coded Tone Controlled Squelch System (CTCSS) consists of 38 Sub-Fre- quencies. This feature allows you to utilize the coded squelch tones (01-38) within each main channel (1-14). This enables you to communicate with another party on the same main channel using the same subcode. The 11

****** Page 12 ****** CTCSS filters out unwanted transmissions without the same coded squelch tone). To change the CTCSS Sub-channel, – From the FRS standby mode, press the MODE Button twice; the sub- channel number will flash as it is displayed. If OF is displayed, press the Up or Down button to enable the CTCSS mode; the CTC icon will appear steady on the display with the flashing sub-channel number. – Then press the Up or Down button to select the desired sub-channel for use. – Press the Power On/Off button momentarily to confirm selection. The CTCSS mode can be turned off by selecting the OF icon with the Up or Down button. NOTE: To communicate with other FRS units, they must be switched to the same channel and CTCSS subcode. To communicate with other FRS units that do not have subcodes, switch your unit to the same channel with the subcode set to OF The CTCSS subcodes do not prevent others from hearing your transmission. This will only allow you to ignore all traffic on a given channel not using the same subcode. Transmit Power Selection Mode This feature permits selection of the transmitting power level at high or low. When set to low, the transmit range of the unit will be less; however, battery life will be increased. To access the transmitter power selection function: Press the Mode Button 3 times until the Po icon appears with a flashing HI or Lo indication on the display. Press the Up or Down button to toggle between the High and Low se- lections. Momentarily press the Power Button to confirm selection. The display will indicate the current setting in standby mode. 12

****** Page 13 ****** Dual Watch Mode This feature allows you to monitor two channels. While in dual watch mode, the unit will continuously monitor both the primary and dual watch channel. Received signals will be played for 5 seconds then the other channel will be scanned. Pressing the PTT button during a received transmission will set the unit to transmit on the same channel. Pressing the PTT button when no signal is received will set the unit to transmit on the primary channel. To set the Dual Watch Mode. From the FRS standby mode, press the MODE button 4 times; the DW icon flashes on the display. If the dual watch mode is off, the OF icon will also appear flashing. To enable the dual watch mode press the Up or Down button; the dual watch channel number will flash and start to increment up or down as the Up or Down button is pressed. The DW icon appears steady on the display. Press the MODE button again to enter the CTCSS function and select the desired CTCSS code for the dual watch channel previously en- tered. Press the Power On/Off button to confirm selection of the dual watch channel. The display will now alternate between the primary channel and the dual watch channel just selected. Momentarily press the SCAN button to exit the dual watch selection mode. Key Tone This feature allows the transceiver to sound a tone whenever the following keys are pressed: Monitor (LIMON) Button, Up/Down Buttons, MODE But- ton, or SCAN Button. To turn the key tones on or off, From the FRS standby mode, press the MODE Button 5 times until bp, the Bell ( ) icon, and On or OF flash on the LCD display. Press the Up or Down Button to toggle the key tone feature On or Off. Momentarily press the Power Button to confirm your selection. 13

****** Page 14 ****** When the key tone feature is on, the Bell icon appears steady on the display, and the beep tones sound in response to each button activation Roger Beep Tone The Roger Beep is a tone which is automatically transmitted whenever the PTT button is released . This tone alerts the receiving party that the trans- mission has been terminated intentionally. To enable and disable the Roger Beep tone. From the FRS standby mode, press the Mode Button 6 times until rb appears on the display with the flashing Roger Beep icon (t ) and On or OF. Press the Up or Down Button to select the tone on or off as desired. – Momentarily press the Power On/Off Button to confirm selection. When enabled, the tone icon ( J” ) appears steady on the display. Call Ringer Selection Mode The transceiver provides 5 user-selectable call ringer melodies to alert you to an incoming call. To select your favorite call ringer melody: From the FRS standby mode, press the MODE button 7 times; CA will appear on the display, together with a flashing number between 1 and 5, and an appropriate call ring. Press the Up or Down Button to preview and hear the 5 available call melodies. – Momentarily press the Power On/Off button to confirm your selection. VOX Selection Mode This option enables you to have hands-free conversation. Your voice or other relatively loud noises are detected and the radio transmits without the need to press the PTT button. To set radio for VOX operation, 14

****** Page 15 ****** From FRS standby mode, press the VOX button; Vo appears steady and VOX icon and sensitivity level (if VOX is enabled) flashes on the display. Press the Up or Down button to select the desired VOX sensitivity level (1 is the most sensitive, 5 is the least sensitive, OF represents off). Momentarily press the Power On/Off button to confirm the VOX se- lection. The VOX icon will appear steady on the LCD display whenever the VOX feature is in use. VOX can be turned off by selecting OF as the setting. NOTE: When the unit is transmitting in the VOX mode, no functions on the unit will operate. To regain control of the functions, it may be necessary to reduce ambient noises. Scan Operation This feature allows you to monitor all channels and tone codes (CTCSS) automatically for valid signals. While scanning, you can transmit and re- ceive. During reception, the scan function is interrupted and will return to the scan mode after 5 seconds. To enable the channel scan mode, Momentarily press the SCAN Button; (SCAN) will appear on the LCD display. – The radio will display each channel (1-14) in order as the scan mode operates to find an active main channel. – When unit doesn’t find any signals and you want to transmit, press the PTT switch to return to home channel operation. The transceiver will automatically resume scanning approximately 5 seconds after the transmission is completed. If there is no activity and you want to leave the scan mode, press the SCAN button momentarily and the unit will return to normal operation; (SCAN) icon will disappear from the LCD display. 15

****** Page 16 ****** CTCSS Scan Operation This feature will scan all CTCSS codes for a single channel. It will pause to play any active transmissions then resume scanning 5 seconds after end- ing transmission. When in CTCSS scan mode the receiver will ignore uncoded transmissions. This feature is useful to establish communications with other users utilizing CTCSS coded transmissions. To activate the tone code (CTCSS) scan mode, From FRS standby mode, press the MODE button twice to select the CTCSS function. Press the SCAN button; the radio will begin scanning for all tone codes (01-38) relative to the current main channel selection. To disable the tone code scarm press the SCAN button again, and the radio will return to normal operation with the same tone code at which the CTCSS scan function was stopped. Auto Key Lock Selection Mode This feature prevents accidental channel change to the preferred settings of the unit. The Auto Key Lock function temporarily disables the Up, Down and Mode Buttons. To access the Auto Key Lock selection menu: From the FRS standby mode, press and hold the SCAN Button for over 2 seconds to Lock the Auto Key function; the ( ) icon appears on the display. – To unlock the Auto Key function, press and hold the SCAN button for at least 2 seconds; the ( ) icon disappears from the display. The PTT and Monitor Buttons are not effected. 16

****** Page 17 ****** Weather Band Operation Channel Selection This feature provides access to 10 channels within the weather band (7 NOAA channels and 3 Canadian marine channels). The radio must be in the weather channel mode. ( Refer to FRS-IOOO Operational Modes.) To change the channel: – From the Weather band standby mode, press the MODE button once until the channel number flashes. Press the Up button briefly to move to the next higher main channel number. Press the Down button briefly to move to the next lower main channel number. Weather Alert Mode Whether the unit is in FRS or weather band mode, if a weather alert signal is received, the unit will generate a warning tone. Press any key except the PTT button. The unit will then revert to a previously selected weather channel for monitoring purposes. To access the weather alert function: – From FRS or Weather Band standby mode, press the ALT button to access the weather alert function; the weather alert icon (R ) appears flashing on the display, and the ALT LED lights red. Momentarily press the ALT button again to exit the Weather Alert function.

****** Page 18 ****** Additional Functions When one or more segments of the battery ( ) icon appear(s) flashing on the LCD panel, recharge unit or install new Audiovox approved recharge- able batteries. If this icon continues to flash on the LCD, please contact your authorized service center. Prior to contacting your authorized service cen- tery please check the following 1 . Check the operating procedures. 2. Verify correct battery installation. 3. Install new, charged Alkaline batteries and check functions. 4. Check that AC adapter is plugged into a working AC power outlet. NOTES FOR GOOD COMMUNICATION 1. 2. The FRS-IOOO 14 channels are shared on a “take turns” basis. This means other groups may be talking on any of the channels. A common code of ethics/courtesy is to switch to another vacant channel and not to attempt to talk over someone who is already using the channel you first selected. The FRS-IOOO has been designed to maximize performance and improve transmission range to field units. To avoid interference, it is 18

****** Page 19 ****** recommended that you do not use base and field units closer than 5 feet apart. 3. For best transmission results, always keep your mouth about 2- 3 inches from the microphone (11) and speak slowly in a normal voice. Warning • Remove the batteries from the transceiver if it is not expected to be used for long periods. This will eliminate the possibility of chemicals leaking from the batteries and corroding the transceiver. • Avoid exposing the transceiver to water or extremes of temperature. • Do not use this device in or near a mining facility, which uses remotely triggered explosives or in areas labeled “Blasting Area”. Premature or accidental detonation may result. • Do not attempt to modify or in any way increase the output of this transceiver. Its output is designed to meet the legal limits set by the FCC. • Do not use this device or change its batteries in potentially explosive atmospheres as sparks in such areas could result in an explosion. • Turn your transceiver off wherever posted notices restrict the use of radios or cellular telephones. Facilities such as hospitals may use equipment that is sensitive to RF energy. Troubleshooting Problem No transmission while pressing the PTT Button Possible cause Weak batteries Incorrect battery polarity 19 Correction Char e orre lace batteries Install the batteries following the directions in paragraph Installing the Batteries.

****** Page 20 ****** Troubleshooting (Cont.) Problem Weak or no signal received Unit beeps, but will not function when turned on Reception of unwanted signals Charge light flashes Possible cause Weak batteries Channel and privacy code not set the same as target transceiver Volume level too low PTT Button inadvertently de ressed Excessive radio interference on a particular channel Obstruction of radio signal Batteries extremely discharged CTCSS privacy mode not on Interference from electronic devices such as computers or TVs Batteries are not installed and CHARGE switch (1) is on 20 Correction Char e or re lace batteries Adjust the transceiver’s settings to match those settings of the target Increase volume level Release PTT Button Change to a different channel Avoid operating in or near lar e buildin s or vehicles Charge or replace batteries Turn on the CTCSS privacy mode and set code number to match the setting of the tar et transceiver. Turn the devices off or move farther away from them. Install Audiovox approved batteries

****** Page 21 ****** Technical Specifications: General Frequency Range: FRS/Weather FRS Channels Privacy Codes Dimensions (W x H x D) (Without Antenna) Power Supply Power Source Battery Backup Operating Time Battery Backup Receiver Useable Sensitivity Maximum Audio Output Power Modulation Distortion Transmitter Maximum RF Output Power High Low Range Maximum Deviation Modulation Distortion Refer to frequency charts 38 for each main channel 4.625 in x 6.875 in x 2.375 in 117.5 mm x 173.4 mm x 60.3 mm AC/DC Adapter Input: 120 Vac Output 12 Vdc, 0.5 Amp Ni-MH rechargeable, AA (4), 4.8 VDC, 1300 mA 30 hours (Transmit: Receive: Standby) (5: 5: 90 ratio) >0.22 UV > 300 mw (8 Ohm ) < 5% (1 kHz 70%) 0.5 Watt ERP 0.5 Watt 0.15 Watt maximum Up to 2 miles +1-2.5 kHz < (1 kHz 70%) 21 ****** Page 22 ****** This transceiver complies with FCC regulations for use in the United States of America. Use in other countries may be prohibited or restricted by local regulation. Please check with the local regulating agency before using this device outside the United States of America. FRS Channel Frequencies: Channel 1 2 3 4 5 6 7 Freq. MHz 462.5625 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 Weather Channel Fre Channel 1 2 3 4 5 Freq. MHz 162.550 162.400 162.475 162.425 162.450 Channel 8 9 10 11 12 13 14 uencies: Channel 6 7 8* 9* Freq. MHz 467.5625 467.5825 467.6125 467.6375 467.6625 467.6875 467.7125 Freq. MHz 162.500 162.525 161.650 161.775 163.275 *Canadian Marine 22 ****** Page 23 ****** Continuous Tone Coded Squelch System Tone Frequencies (in Hz) CTCSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Freq. Hz 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 CTCSS 20 21 22 23 24 25 26 28 29 30 31 32 33 34 35 36 37 38 oF = No Tone 23 Freq. Hz 131.8 136.5 141.3 146.2 151.4 156.7 162.2 167.9 173.8 179.9 186.2 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3 ****** Page 24 ****** 90 DAY LIMITED WARRANTY Applies to Audiovox Family Radio and General Mobile Service Products. AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the warranty center at the address shown below. The Company disclaims liability for communications range of this product. This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/barcode label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in ælnection with the sale of this product. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 1-800-290-6650 128-5385A


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

AUDIOVOX FRS-1000 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.