Click here to download AUDIOVOX AVGMTG10U (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** 10-lnch Roof-Mount DVD Player With DVD/CD/MP3 SYSTEM AVXMTGIOU Audiovo INSTALLATION GUIDE

****** Page 3 ****** TABLE OF CONTENTS Important Notices Materials Included in this Package Removing and Installing Snap On Covers .. General Vehicle Installation Approach Connecting the Dome Lights 10

****** Page 4 ****** IMPORTANT NOTICES Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes anchor points in A, B, C or D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants. If you have any question regarding routing in a vehicle, please contact Audiovox Technical support at 1-800-225-6074. An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver only if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied. When connecting power and ground in a mobile video installation, insure that the ACC wire is fused at the point where it is connected to the vehiclés ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product. An LCD panel and/or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. WARNINGS • Do not use any solvents or cleaning materials when cleaning the video monitor. Do not use any abrasive cleaners, they may scratch the screen. Use only lightly dampened lint free cloth to wipe the screen if it is dirty. Lock the LCD screen in fully closed position when not in use. • Before putting on headphones, always adjust the volume setting to OFF or lowest position. Remember to leave the dome light switch in the off or auto position when the vehicle is unattended, as the dome lights, if left on, can drain the vehicle battery. • Do not put pressure on the screen. Caution children to avoid touching or scratching the screen, as it may become dirty or damaged. Safety Precautions For safety reasons, when changing video media, it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system. System adjustments can be accomplished using the remote control, while seat-belts remain fastened. Enjoy your AUDIOVOX entertainment system but remember that the safety of all passengers remains the number one priority. Licensed under one or more of the following patents, Patent Numbers and 2

****** Page 5 ****** MATERIALS INCLUDED IN THIS PACKAGE 1 5 9 2 6 10 3 7 11 10″ LCD Overhead Monitor with DVD player 6 Pin Power Harness 2. 2 Pin Power /Wire Harness with Choke 3. 4 3 RCA Jack Pigtail 4. Hardware Package 5. M5*9 TA4*9 Remote Control 6 Mounting Bracket 7. Snap-on Shroud 8. 8 Snap-on Screen Cover 9. Pry Tool 10. II. 3.5mmTIP/3RCA JACK PIGTAIL 12. Trim Ring 12 (1 pc) (l pc) (1 pc) (1 pc) (4 pcs) (6 pcs) (1 pc) (1 pc) (2 pcs)* (2 pcs)* (l pc) (1 pc) (3 pcs) *Note: The AVXMTGIOU is supplied with a black snap-on shroud and screen cover. To install the pewter or shale snap-on shroud or screen cover, the black snap- on shroud and screen cover must be removed first. See the following page for the removal process. 3

****** Page 6 ****** REMOVING AND INSTALLING SNAP-ON COVERS Preparation Place the unit on a soft surface to avoid damaging the plastic. Materials Required 2. Shroud 3, Screen Cover 4. Pry Tool ICY Overhead LCD Monitor with DVD Player Disconnecting the Screen Cover 1. 2. Open the LCD screen. Insert the supplied pry tool between the LCD screen and snap on screen cover at locations “At and “C” and gently pry the cover away from the screen. 4

****** Page 7 ****** Installing the Screen Cover 1. 2. 3. Open the LCD screen. Hook the two tabs “D” at the bottom edge of the screen cover into the notches on the bottom edge of the LCD screen. Snap the opposite side of the screen cover over the hinges.. Disconnecting the Shroud (fastener} 1. 2. Open the LCD screen. Insert the supplied pry tool between the unit and shroud at fastener location “E” and gently pry the shroud away from the unit. 5

****** Page 8 ****** Installing the Shroud 1. 2. Open the LCD screen. Slide the shroud over the unit. The shroud will snap into place at locations “F! 6

****** Page 9 ****** GENERAL VEHICLE INSTALLATION APPROACH 1. 2. 3. 4. 5. 6. 7. 8. 9. Decide upon the system configuration and options that will be installed. Review all manuals to become familiar with electrical requirements and hookups. Decide upon the mounting locations of all components and the method of mounting. Prep the vehicle. Remove any interior trim necessary to gain access to vehicle’s wiring, as well as all areas where interconnecting wire harnesses will be located. If any access holes need to be cut into the vehicle, do this now. Route the wiring harnesses in the vehicle as necessary. Refer to the wiring diagrams in this manual, as well as the wiring instructions for the individual components and accessory options being installed Ensure that the wiring is protected from sharp edges. Ensure that all wiring is not pinched when all components and interio trim are fully installed. Leave enough slack in the wiring at each component to allow working room. Remove all AN system components from their packaging and place them loosely in the vehicle at their respective locations. Connect all components together and verify the proper operation of all system functions. Note: This is best done BEFORE components have been permanently mounted. After verifying proper operation ofthe system, proceed to mount each component. When all components are mounted, recheck the function of the entire system. Ensure that no wiring was pinched or connected improperly during final installation. 7

****** Page 10 ****** GENERAL VEHICLE INSTALLATION APPROACH Installing Unit to Roof 8 Roof Roof Suppolt Headliner Mounting Bracket Selfdrilling Screws Video Unit M5 Screw

****** Page 11 ****** GENERAL VEHICLE INSTALLATION APPROACH 00 o To Dome Lights See “Connecting the Dome Lights” 2 Pin Power Wire Harness with Choke o o 6 Pin Power Harness o AV IN 3 RCA Jack Pigtail 9 *Optional Relay Box Signal Harness

****** Page 12 ****** CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle’s wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on. Negative switched systems apply ground to illuminate the bulbs. To determine which system you have, you must locate the wires at the dome light. On a positive switched system, with all the doors closed and lights out, both wires at the dome light will rest at ground. When the light is activated, one of these wires will switch to +12 VDC. This is the vehicle’s switching wire. On a negative switched system, with all the doors closed and lights outf both wires at the dome light will rest at +12 VDC When the light is activated, one of these wires will switch to ground. This is the switching wire. For positive systems, connect the purple/brown (Lamp auto) wire to the vehicle’s switched wire. Then connect the red/black (Lamp on) wire to a fused constant 1 2 volt source and the black/red (Lamp common) wire to a good ground. Positive systems are commonly found on Ford vehicles. For negative systems, connect the purple/brown (Lamp auto) wire to the vehicle’s switched wire. Then connect the red/black (Lamp on) wire to a good ground and the black/red (Lamp common) wire to fused constant 1 2 volt source. Negative systems are commonly found on General Motors and import vehicles. Note: Some vehicles which incorporate transistorized control of the dome light circuit, such as the 1999 Dodge Caravan, may require that the purple/brown (Lamp auto) wire be connected to the door pin switch wire, as the additional current draw of the Monitor’s lights may not be supported by the output of the vehicle’s body control computer.. 10

****** Page 13 ****** Positive Switched Dome Lighting To 6 pin connector on Monitor To constant +12 VDC Red/bIack-Lamp on Black/red-Lam common Pur le/brown-Lam Auto Factory Door Ajar Switch or Body Control Computer II To constant +12 VDC

****** Page 14 ****** Negative Switched Dome Lighting To 6 pin connector Red/bIack-Lam on Black/red-Lam common Pur Ie/brown-Lam Auto Factory Door Ajar Switch or Body Control Computer 12 To constant +1 2 VDC To constant +1 2 VDC

****** Page 15 ****** This page intentionally left blank. 13

****** Page 16 ****** 0 2010 AUDIOVOX,150 Marcus Blvd. Hauppauge, NY 1 1788 For Customer Service Visit Our Website At mobile.audiovox.com Product Information, Photos, FAQ’s Owner’s Manuals 128-8902

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



AUDIOVOX AVGMTG10U (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.