Click here to download AUDIO-TECHNICA ES925C24-FM5 (01) PDF MANUAL

PDF Content Summary:

****** Page 1 ****** Introduction Thank you for purchasing this product. Before using the product, read through the user manual to ensure that you will use the product correctly, Please keep this manual for future reference. Features e Modular microphone system comprised of an ES Series capsule, gooseneck assembly, and power module. • RGB LEDs built into both the flush-mount power module and gooseneck assembly indicate the on/off status of the microphone. • Includes external control function for device control from the capacitive touch switch. Safety precautions Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product. Cautions for the product • Do not subject the product to strong impact to avoid malfunction. e Do not disassemble, modify or attempt to repair the product • Do not handle the product with wet hands to avoid electric shock or injury. • Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place. ES925C6/FM5 ES925C12/FM5 ES925C15/FM5 ES925C18/FM5 ES925C21/FM5 ES925C24/FM5 User Manual CARDIOID CONDENSER MODULAR GOOSENECK MICROPHONE WITH 5-PIN FLUSH-MOUNT POWER MODULE audio-technica Notes on use • Check the strength of the mounting area. Insufficient strength or poor mounting will cause objects to fall or become damaged. • The circuitry in the microphone takes about 30 seconds to stabilize after power is supplied. You may hear some audio disturbance during startup. • Install the microphone on a flat, unobstructed mounting surface, • Depending on the surface finish of a table, the isolators may leave marks on the table. • Do not excessively bend the gooseneck assembly, rotate the ends of the capsule, or pull on them. Doing so may cause disconnection or malfunction. • The product is a modular system comprised of a microphone element, gooseneck assembly and power module. Make sure the parts are firmly attached before use. • Do not remove the rubber O-ring on the power module connecting part at the lower section of the gooseneck assembly. • When attaching parts, remove the black cap on the capsule connecting part of the gooseneck assembly. Do not remove the silicone part at the end of the capsule connecting part. Silicone part Do not remove

****** Page 2 ****** Assembly • Insert the gooseneck assembly (c) while rotating it into the flush-mount power module (d). • Tlghten until it does not rotate, and use the hex wrench (i) to tighten the set screw (h) and set the gooseneck assembly in place. • Connect the capsule (b) to the gooseneck assembly, and attach the windscreen (a). * If the parts are not sufficiently tightened together, problems may occur such as the LED colors of the gooseneck assembly and power module not matching or sound is not output. e Refer to the LED table to the right and set the LED color before attaching to the mounting surface. • If you are installing the flush-mount power module on a table without the isolators, you must make a hole with a diameter of 20.5 mm in the mounting surface. • If you are installing with the isolators, the hole must have a diameter of 23.5 mm. Inserting the isolators between the mounting surface and power module allows you to separate the flush-mount power module from the mounting surface, • Attach the upper part isolator (e) to the mounting surface, and attach the flush- mount power module (d). Attach the lower isolator (f) to the reverse side of the mounting surface, and then tighten the nut (g). a b c d f Switch setting and functions 5 4 1 . Action OFF 4 BLUE Wiring PINI (Ground} PIN2 (Hot) Contact Closure GND 3. Audio status MIC 2 4. LED color LED COLOR 2. Contact closure status RED 5 MAGENTA MIC OFF 5 3 2 GREEN 6 CYAN 5 3 5. LED status 3 YELLOW 7 WHITE PINS {LED PIN4 (Contact closure) PIN3 (Cold} 2

****** Page 3 ****** Specifications ES925Cx/FM5 Element Polar pattern Frequency response Open circuit sensitivity Impedance Maximum input sound level Dynamic range Signal-to-noise ratio Phantom power requirements Contact closure Closure input voltage Maximum permissible power On-resistance LED control Active low voltage Maximum permissible input power Maximum permissible power Weight Dimensions OUIPUt connector Optional interchangeable elements Included accessories x = 6/12/15/1821124 back plate. permanently polarized condenser Cardioid 30 – 20,000 Hz -40 dB (10.0 mV) (OdB=1V/Pa, 1kHz) 130 ohms 140 dB SPL (1kHz at 1% THC)) 112 dB at Max SPLI 66 dB (1 kHz at IPa, A-weighted} 22 – 52 V DC, 7.6 mA 0.5 – v 200 mw 100 ohms Active high (+5 V DC) TTL compatible 1.2 V or lower -0.5 – 5.5 v 200 mw ES925C6/FM5: 109 g (3.8 ES925C12/FM5: 133 g (4.7 ES925C15/FM5: 138 g (4.9 ES925C18/FM5: 143 g (5.0 ES925C21/FM5: 148 g (5.2 ES925C24/FM5: 153 g (5.4 ES925C6/FM5: 207.6 mm (8.2″) x 38 mm (1.5″) x 48 mm (1.9″) Polar pattern 270* 240* 210• 180* LEGEND 120′ 150+ SCALE IS 5 DECIBELS PER DIVISION Frequency response 20 5k 20k Frequency in Hertz Dimensions — 2001-12 1 kHz 5 kHz 8 kHz LEGEND oat 50crn o o ES925C12/FM5: 315 mm (12.4″) x 38 mm (1.5″ ) x 48 mm (1.9″) o O o O ES925Cl 5/FM5: 391.2 mm (15.4″ ES925C18/FM5: 467.4 mm (18.4″ ES925C21/FM5: 5/13.6 mm (21.4″ ES925C24/FM5: 619.8 mm (24.4″ (HxWxD} 5-Pin XLRM-type ) x 38 mm (1.5″) x 48 mm (1.9″) ) x 38 mm (1.5″) x 48 mm (1.9″) ) x 38 mm (1.5″) x 48 mm (1.9″) ) x 38 mm (1.5″) x 48 mm (1.9″) ESE-Ha ESE0a (3600), ESE-MLa (900) Isolator 1 pair, Nut, Windscreen AT8109a, Set screw (M2x2 mm (0.08″}) 2 pcs., Hex wrench (089 mm (0.04″}) 08.4 ES925C12/FM5 ES925C15/FM5 20.0 ES925C18/FM5 ES8755RC (FM5) ES925C21/FM5 ES925C6/FM5 Audio-Technica Corporation 246-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan @2020 Audio-Technica Corporation Global Support Contact: Made in Japan 38.0 ES925C24/FM5 (unit: mm) ver-1 2019.06.01 1424198100202 ver.2 2020.07.15 3








Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.