Click here to download AUDIO-TECHNICA ATW-R3210 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** 3000 Series User Manual UHF Wireless Systems ATW-R3210 Receiver ATW-T3201 Body-Pack Transmitter ATW-T3202 Handheld Transmitter UHF SYNTHESIZH) (IVERSITV RECEIVER audio-technica SYNC audio-tech’ic.a BACK ATW-R3210 PUSH ENTER audio-technica

****** Page 2 ****** How to insert batteries……………………………………………………….g ATW-T3201 . ATW-T3202 … .. 8 How to attach and detach the interchangeable microphone capsule (only for ATW-T3202)…………………………………. How to attach How to remove . How to read the display ….. ….. ….. ….. ……………… ATW-R3210. ATW-T3201/ATW-T3202….. How to operate………………………………………… …… ………………13 Basic operation Using QUICK SYNC…… Settings ………………………………………………………………………….14 ATW-R3210. ATW-T3201/ATW-T3202….. Setting ATW-R3210 ….. ….. ….. ….. ….. …. List of setting items . Setting the operating frequency Setting the channel (receiver) name Setting the audio output level. Scanning for open channels ….. ….. ………………… Setting transmitters via IR SYNC . 16 Setting the squelch level… Setting the system-related functions…………………………………………………… 17 Setting ATW-T3201/ATW-T3202…………………………. List of setting items Setting the transmission frequency Setting the channel (transmitter) name 20 Setting the gain… Setting the RF transmission output Setting HPF (High-Pass Setting lock Setting the function for the function button…. Setting the mute mode (only for ATW-T3201) ….. ….. ….. ….. . 22 Setting the system-related functions…. How to attach the transmitter (ATW-T3201) ….. ….. ….. .. Making connections (basic connections) ….. ….. ….. .. ……………..24 Using IR SYNC………………………………. Achieving stable reception ………………………………………………..25 Contents Introduction ………………………………………………………………………2 Rack-mounting the receiver……………………………………………….25 Important information ………………………………………………………..2 Troubleshooting ……………………………………………………………….26 ……3 ATW-T3201/ATW-T3202 26 Dimensions……………………………………………………………………..27 ATW-T3201 28 ATW-T3202 .. 28 Specifications ………………………………………………………………….29 Overall system 29 ATW-R3210. 29 ……….10 15 .. ….. 15 ……20 ….. ….. 21 .. ….. 21 … ……24 ……..25 Notes on use …………………………………………………………………….3 Part names and functions……………………………………………………4 ATW-T3202 ATW-R3210. ATW-T3201 . .4 10 12 13 13 14 15 15 16 16 17 .20 .20 .21 .21 .21 .22 ATW-R3210. ATW-R3210. ATW-T3201 . ATW-T3202 .26 27 .29 .30

****** Page 3 ****** Introduction Thank you for purchasing this Audio-Technica product. Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future Important information Warning: • To prevent fire or shock hazard, do not expose this apparatus to rain or moisture. Caution: Do not expose this apparatus to drips or splashes. • To avoid electric shock, do not open the cabinet. Refer servicing to qualified personnel only. • Do not expose this apparatus to excessive heat such as that generated by sunshine, fire or other heat sources. Do not subject this apparatus to strong impact. • This apparatus should be located close enough to the AC outlet so that you can easily grasp the AC adapter at any time. In case of emergency, disconnect the AC adapter quickly. • Do not place any objects filled with liquids, such as vases, on this apparatus. • To prevent fire, do not place any naked flame sources (such as lighted candles) on this apparatus. Do not install this apparatus in a confined space such as a bookcase or similar unit. Install this apparatus only in the places with good ventilation. • The rating label is put on the bottom of this apparatus. Battery caution: • Keep batteries out of the reach of children. • Observe correct polarity as marked. • Do not expose the battery to excessive heat such as sunshine, fire or the like. • Always consider the environment issues and follow local regulations when disposing of batteries. • Remove depleted battery immediately. • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Use only disposable LR06(AA) alkaline or NiMH batteries. • Do not use new batteries and old one at the same time. • Do not use different battery types or models. • Do not use a leaking battery. If battery leakage occurs, avoid contact with skin. If contact occurs, immediately wash thoroughly with soap and water. • If battery leakage comes into contact with your eyes, immediately flush with water and seek medical attention. For customers in the USA FCC Notice Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. For customers in Canada IC statement CAN RSS-Gen/CNR-Gen This device complies with INDUSTRY CANADA R.S.S. 210. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference which may cause undesired operation. This device complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. 2

****** Page 4 ****** Notes on use • Be sure to read the user manual for any microphone or cable that you attach to the product. • Disconnect the AC adapter from the outlet when this product is not in use. • Turn off the power of this product before connecting or disconnecting cables. • If you use the product near a TV or radio antenna, you may hear unwanted noise in the television or radio. If this occurs, move the product away from the device. • Two waves of the same frequency can’t be used simultaneously. • Be careful of interference noise caused by the surrounding radio wave environment and use of multiple systems. • Wireless systems may be affected by the spark noise of vehicles, dimmer of lighting apparatus, computers, office automation apparatus and electronic musical instruments. Place and use the product where it is less likely to be affected by the above. • Be sure to use this product in combination with components specified by our company. • Be sure the connected cable is plugged all the way into the product. • When you connect the product with a mixer, turn off the phantom power source. • If you use the product close to an electronic or communications device (such as a mobile phone), the product may produce unwanted noise. If this occurs, move the product away from the device. • When setting up the product, make sure there are no obstacles between the transmitter and the receiver that might block the signal. •To prevent the batteries from wearing out, turn the transmitter off when not in use. • Over time, discoloration may occur due to ultraviolet rays (especially direct sunlight) and friction. • It is legally prohibited to dismantle and modify this product. In addition, this product is so precisely manufactured that dismantling it could cause electric shock, failure or fire. Never dismantle this product. Using multiple wireless systems • If you use more than one device at the same time, use them in the same group. • When using multiple units simultaneously, maintain 1 meter or more between individual transmitters and 3 meters or more between transmitters and receivers’ antennas. • When using multiple units, power on transmitters one by one, making sure there is no unwanted noise. • When a howling (beeping or squealing) sound is produced during use, turn down the output volume of the connected mixer/amplifier. Maintenance • If the product becomes stained or covered with dust, be sure to disconnect the power plug before wiping it off with a dry and soft cloth. • Do not use benzine, thinner or electrical contact cleaner, etc. They may deform or otherwise damage the product, or cause operational failure. 3

****** Page 5 ****** Part names and functions ATW-R3210 Front panel audio-technica UHF SYNTHESIZED DIVERSITY RECEIVER ATW-R3210 O SYNC 0 BACK PUSH ENTER Power button ( (b ) Use to turn the receiver on or off. IR sync window Use to IR SYNC with the transmitter (ATW-T3201, ATW-T3202). Display Displays the receiver state and setting menus. BACK button Press to take the display back one screen. Returns to the Main screen when pressed and held. Control dial Switches the screen when you turn the dial. Displays the setting menu when you press the dial. Turn the dial to select a setting and press to confirm. When you press and hold the dial, QUICK SYNC is started. 4

****** Page 6 ****** Part names and functions Rear panel 121/ — 80mA ANT B O Antenna input jack Each jack supplies DC 12 V to a connected antenna. 12V 80mA ANT E! O UNBAL o BAL AF OUTPUT O LIFT o GND 12V IA O 9 Additionally other compatible accessories (sold separately) can be connected. Unbalanced output terminal (6.3 mm mono jack) Balanced output jack (XLR 3-pin male) GND BAL Ground lift switch HOT COLD This switch isolates the GND pin of the balanced/unbalanced output from the ground. Normally this is kept in the GND position, but if a hum develops due to a ground loop, switch to the LIFT side. DC input terminal Connect DC plug from the included AC adapter. AC adapter cord hook Hang the power cord of the AC adapter to prevent it from pulling loose accidentally. 5

****** Page 7 ****** Part names and functions ATW-T3201 o Transmission antenna MUTE switch ATW-T3?01 czc:z O 10 12 13 o 14 O 15 SYNC button O Switches audio mute on and off. Indicator LED that shows the status of the transmitter. When the power is turned ON: Solid green When the transmitter is muted: Solid red Function button Press briefly to turn the screen back on if it shuts off. Press and hold to perform preselected function. Input connector Connect a microphone, a headworn microphone, a guitar cable, etc. Pin 1: GND Pin 2: Instrument input Display Shows the current status. Pin 4: +5 V output Pin 3: Microphone input Use to IR SYNC with the receiver (ATW-R3210). UP button Use to select various settings. BACK button Press to return to the previous screen. Returns to the Main screen when pressed and held. Power switch Use to turn the power on or off. SET button Press to confirm a selection. DOWN button Use to select various settings. Battery cover IR sync window Use to IR SYNC with the receiver (ATW-R3210). Charging terminal If no buttons are pressed for a period of 30 seconds, the display will turn off. 6

****** Page 8 ****** Part names and functions ATW-T3202 O 0 o 11 SYNC button 12 14 O O Interchangeable microphone capsule Display Shows the current status. If no buttons are pressed for a period of 30 seconds, the display will turn off. Grip case UP button Use to select various settings. BACK button Press to return to the previous screen. Returns to the Main screen when pressed and held. IR sync window Use to IR SYNC with the receiver (ATW-R3210). DOWN button Use to select various settings. ET button Press to confirm a selection. 12 7 Use to IR SYNC with the receiver (ATW-R3210). Power switch Use to turn the power on or off. Battery cover Function button Press to turn the screen back on if it shuts off. Press and hold to perform preselected function. Indicator LED that shows the status of the transmitter. When the power is turned ON: Solid green When the transmitter is muted: Solid red Charging terminal

****** Page 9 ****** How to insert batteries ATW-T3201 ATW-T3202 1. 2. 3. Slide the battery cover latches down. [4) Open the battery cover while the latches are slid. Insert the batteries according to the plus (+) and minus (-) marks found inside the battery compartment. o o 1. 2. 3. Rotate the grip case of the battery compartment. Open the battery cover. • Put your finger on the hook of the battery cover and pull it to open the battery cover. Insert the batteries according to the plus (+) and minus (-) marks found inside the battery compartment. 8

****** Page 10 ****** How to attach and detach the interchangeable microphone capsule (only for ATW-T3202) How to attach 1. 2. 1. 2. Attach the microphone capsule to the body of the transmitter. Rotate the microphone capsule clockwise to tighten it. How to remove Rotate the microphone capsule counterclockwise to loosen it. Detach the microphone capsule from the body of the transmitter. • Do not directly touch or scratch the connection surface. • Be sure to turn off the power of the transmitter before attaching/ detaching the microphone capsule. • Do not forcibly attach the microphone capsule. Doing so may damage the transmitter or microphone capsule. 9

****** Page 11 ****** How to read the display ATW-R3210 Main screen O a TX HPF 30mW O Transmitter information display area VOCALI G:06 c •12 O O MHz O o o Information on the connected transmitter is displayed. Refer to “Transmitter information display area” (p. 10) for screen display. RF level indicator Displays the strength of RF reception for antennas A & B. Name display Displays the specified name. O Frequency indicator Displays the set frequency. Receiver mute indicator A speaker icon with a slash through it is displayed when the receiver is muted. AF level indicator Displays the strength of the received audio signal. Transmitter information display area Group indicator Channel indicator Backup frequency indicator “BU” icon is displayed when the backup frequency mode is ON. Lock status indicator Antenna input power indicator Icon is displayed when the antenna power supply is ON. O a TX 30mW Normal O a TX MUTE Muted O Battery level indicator Transmitter mute indicator O a -rx Non-communication O Lock status indicator @ High-pass filter indicator 0 RF transmission output indicator A microphone with a slash through it is displayed when the transmitter is muted. o Transmitter non-communication indicator 10

****** Page 12 ****** How to read the display Level meter screen O TX-RF PWR 30mw B RX o -92 -86 -80 -74 dBm O-30-24-18-15-12-10 -8 -6 -4 -2 0 +2 +4 +6 dBu O RF transmission output indicator (transmitter) Marker (when the minimum hold function is on) Shows the minimum level at which the RF is held. Mute indicator A speaker icon with a slash through it is displayed when transmitter is muted. Minimum hold function Audio output indicator (receiver) Gain indicator (transmitter) Overload (excessive input) indicator If you press the BACK button on the level meter screen, the minimum hold function turns on and its marker is displayed. • The marker indicates the lowest level of RF signal received from the transmitter. • The marker does not move if the input RF level is higher than the marker position. • If the RF level input is lower than the marker position, the marker moves in tandem with the RF level. •To reset the marker position, press the BACK button again. Switching between screens The screen is switched every time the control dial is rotated right or left. TX B HPF 30mW VOCALI 000.000MHz G:06 c: 12 Main screen -92 -80 -74 dBm TX-RF PWR 30mw B m+12dB m-10dB -40-30-24-18-15-12-10 -8 -6 -4 -2 0 +2 +4 +6 dBu Level meter screen 11

****** Page 13 ****** How to read the display ATW-T3201/ATW-T3202 The main screen is displayed when the power is switched on. If you press the UP/Down button on the main screen, the screen display is switched. o 000. OO O VOC Ll 0 12 /L….IX Gr:02 Ch•.05 O 0 O RF transmission output indicator : RF Power High (30 mW) : RF Power Low (10 mW) : RF Power Off High-pass filter indicator Name display Displays the specified name. Group indicator Channel indicator o O Frequency indicator Displays the set frequency. @ Lock status indicator @ Battery level indicator 75% or more battery power remaining. [11* : 50 to 75% battery power remaining. : 25 to 50% battery power remaining. 25% or less battery power remaining. (Flicker): Replace the batteries.

****** Page 14 ****** How to operate Basic operation 1. 2. 3. 4. 5. 6. Turn on the power button of the receiver (ATW-R3210). • The display lights and the main screen is displayed. SYNC Set the operating frequency. Using QUICK SYNC You can easily send the frequency and the channel name of the receiver with QUICK SYNC. m w•H2’t 1. 2. 13 Press and hold (for approximately 2 seconds) the control dial on the main screen. Select [Sync] and press the control dial. • Communication function is in standby. Refer to “Using IR SYNC” (p. 25) for subsequent steps. Turn on the power switch of the transmitter (ATW-T3201/ATW- T3202). • The indicator lights and the display shows the main screen. ATW-T3201 UHF Set the transmission frequency. ATW-T3202 Check the RF level indicator on the receiver. • Check that antenna A or B lights up. Speak into the microphone. • Make sure the AF level indicator lights up on the receiver.

****** Page 15 ****** Settings Various settings can be made from the menu screen shown on the display. ATW-R3210 Press the control dial. • The main menu screen appears. @ CD SYNC ancK 3. Press the SET button to display the settings screen for the selected item. • Press the BACK button to go back one screen. • To cancel partway through making a setting, press the BACK button. • While on the settings screen, the display will return to the main screen if approximately 30 seconds pass without a button being used. 2. 3. Turn the control dial to select the item you wish to set. a TX B HPF 30mW VOCALI UTILITIES 000.00 FREQUENCY NAME G:06 C: 12 XXXN//////////Y AF Press the control dial to open the settings menu of the selected item. • Press the BACK button to go back one screen. • To cancel partway through making a setting, press the BACK button. • While on the settings screen, the display will return to the main screen if approximately 60 seconds pass without a button or the control dial being used. ATW-T3201/ATW-T3202 Press the SET button. • The menu screen appears. ATW-T3201 LT’W-TIZ4′ ATW-T3202 2. Press the UP/DOWN button to select the item you wish to set. FREQUENCY Selected menu item OOO. OOO MHz Current setting value 14

****** Page 16 ****** Setting ATW-R3210 List of setting items Setting by group/channel FREQUENCY MANUAL Gr/Ch NAME AUDIO GROUP SCAN TX SYNC SQUELCH UTILITIES Set the operating frequency. Set the channel name. Set the audio output level. Scan for open channels. Set transmitters via IR SYNC. Set the squelch level. Set this function to prevent the receiver settings from being changed Set whether to turn power on or off to the antenna input terminals. Edit the channel allocation for user groups (Ul and U2). Set the backup frequency. Set the item prominently displayed at the center of the main screen. Switch the level meter on the main screen between receiver and transmitter. Set the display brightness. Set the user access level. This returns the receiver settings to their factory defaults. This function displays product information such as the version of the receiver. 1 2. 3. 4. AUTO MANUAL LOCK ANT PWR Gr/Ch EDIT BACKUP FREO DISPLAY AF METER BRIGHTNESS ACCESS RES VERSION From the menu screen, turn the control dial, select [FREQUENCY] and then press the control dial. Select [Gr/Ch] and press the control dial. Turn the control dial to set the group. When finished setting it, press the control dial. Turn the control dial to set the channel. When finished setting it, press the control dial. • The setting is complete. Setting the channel (receiver) name The following characters can be entered: The maximum number of characters that can be entered is 8. Alphabetic (uppercase letters) Numeric Setting the operating frequency Manual setting 2. 3. 4. Symbols (+, —, #, &, period) Space From the menu screen, turn the control dial, select [NAME] and then press the control dial. Turn the control dial, select the desired character and then press the control dial. • Tho character is input and the cursor moves. Repeat the operation in Step 2 to enter all characters. Turn the control dial, select [End] and then press the control dial. • The setting is complete. 2. 3. 4. From the menu screen, turn the control dial, select [FREQUENCY] and then press the control dial. Select [MANUAL] and press the control dial. Turn the control dial to set the first 3 digits. When finished setting them, press the control dial. Turn the control dial to set the last 3 digits. When finished setting them, press the control dial. • The setting is complete. 15

****** Page 17 ****** Setting ATW-R3210 Setting the audio output level Setting transmitters via IR SYNC This function allows you to make transmitter settings on the receiver and then automatically configure the transmitter via IR SYNC. The following are the available settings and setting values: 2. 3. From the menu screen, turn the control dial, select [AUDIO] and then press the control dial. Turn the control dial to set the audio output level. • The level changes 2dB +/- each time you turn the control dial. • It can be set from -60 to OdB. Press the control dial. • The setting is complete. Settings Freq Name RF Pwr Gain Lock Batt HPF Setting values Current setting value, NoChange Current setting value, NoChange Low: 10mW, High:30mW, NoChange -10 to +20dB, NoChange Lock, Unlock, NoChange Alkaline, Ni-MH, NoChange OFF, ON, NoChange Scanning for open channels Scan for unused channels in the current environment for use. 2. 3. 4. 5. From the menu screen, turn the control dial, select [GROUP SCAN] and then press the control dial. Turn the control dial to select the group you want to scan. After selecting a group, press the control dial. Turn the control dial to select the preferred threshold. After selecting the threshold, press the control dial. • You can select [Normal], [Highl or [Lowl sensitivity: High: Prioritize the number of channels. Normal Low: Prioritize stable operation. • Scan starts. Confirm the scan result by selecting [0K] and then pressing the control dial. • If you want to scan over again, select [Retry]. Available channels and frequencies are shown in a list. Turn the control dial, select an available channel and then press the control dial. • The setting is complete. 1 2. 3. 4. 5. From the menu screen, turn the control dial, select [TX SYNC] and then press the control dial. Turn the control dial to select a setting you would like to sync to the transmitter and then press the control dial. Turn the control dial to select the setting value and then press the control dial. Repeat Steps 2 and 3 for each setting you would like to sync to the transmitter. Turn the control dial, select [SYNC START] and then press the control dial. • Communication function is in standby. Refer to “Using IR SYNC” (p. 25) for subsequent steps. 16

****** Page 18 ****** Setting ATW-R3210 Setting the squelch level Setting automatically Setting the system-related functions Setting the lock Set this function to prevent the receiver settings from being changed • The default setting is [Unlock]. 2. 3. 4. From the menu screen, turn the control dial, select [SQUELCH] and then press the control dial. Turn the control dial, select [AUTO] and then press the control dial. Turn the control dial, select [Normal], [High] or [Low] and then press the control dial. • You can select one from [Normal], [Highl or [Low]. High: Prioritize tho sound/voice quality. Normal Low: Prioritize the available range. • If an error message is displayed, change the operating frequency. The error indicates that the current frequency is already in use or that there is excessive noise. Scan starts. The scan result is shown. Press the control dial. • The setting is complete. 1 2. 3. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [LOCK] and then press the control dial. Turn the control dial to select [Lock] or [Unlock], and then press the control dial. • Tho setting is complete. Setting the antenna power Set whether to turn power on or off to the antenna input terminals. 2. 3. Setting manually The default setting is IOFFI. If set to [ONI, power is supplied to both antennas A and B. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [ANT PWR] and then press the control dial. Turn the control dial, select [ONI or [OFF] and then press the control dial. • The setting is complete. 2. 3. 4. From the menu screen, turn the control dial, select [SQUELCH] and then press the control dial. Turn the control dial, select [MANUAL] and then press the control dial. Turn the control dial to select the value you wish to set. • The meter indicates the RF level. • It can be set from levels 1 to 13. • While the available range of the transmitter becomes wider as the squelch level is lower, there may be cases when noises occur under the influence of other radio waves. While the available range of the transmitter becomes narrower as the squelch level is made higher, noises are less likely to occur due to the less influence of other radio waves. Press the control dial. • The setting is complete. 17

****** Page 19 ****** Setting ATW-R3210 Setting user-defined scan groups Aside from the ten preset groups, there are two additional user-defined scan groups: IJI and IJ2. Both Ul and U2 can be edited with up to 32 frequencies. Setting the backup frequency mode If you set the backup frequency in advance, you can switch the frequency of the transmitter and receiver with the transmitter. It is convenient to set this function when you want to switch the frequency easily. • The default setting is [OFF]. 2. 3. 4. 5. 6. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [Gr/Ch EDIT] and then press the control dial. Turn the control dial to select group [Ull or IU2] and then press the control dial. Turn the control dial, select a channel and then press the control dial. Turn the control dial, select [SET] or [RESET] and then press the control dial. • By pressing ISETI, you can set the frequency of tho selected channel. • If you press [RESET], the frequency of the selected channel becomes blank. After setting all channels, turn the control dial, select [Sync] or [Save] and then press the control dial. • If you press [Save], the setting is completed. • If you press [Sync], the screen turns to an IR SYNC standby screen. Execute IR SYNC. 2. 3. 4. 5. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [BACKUP FREQ] and then press the control dial. Turn the control dial, select [ON] and then press the control dial. Turn the control dial, select [Manual] or IGr/Ch] and then press the control dial. • If you select [Manual], you can set the frequency. • If you select IGr/Chl, you can set tho group/channel. After setting each item, turn the control dial, select [Set] or [Sync] and then press the control dial. • If you press [SET], the setting is completed but you must still sync the setting with the transmitter or set the backup frequency manually on the transmitter in order to use tho backup frequency. • If you press ISyncl, the screen turns to an IR SYNC standby screen, Execute IR SYNC. Setting the layout of the main screen Select the item to be prominently displayed at the center of the main screen. The default setting is [Frequency]. 2. 3. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [DISPLAY] and then press the control dial. Turn the control dial, select [Frequency] or [Name] or [Gr/Ch] and then press the control dial. • The setting is complete. 18

****** Page 20 ****** Setting ATW-R3210 Setting the AF level meter on the main screen Switch the AF level meter on the main screen between [Receiver (Rx)] and [Transmitter (TX)]. • The default setting is [RX]. Resetting This returns the receiver settings to their factory defaults. 2. 3. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [AF METER] and then press the control dial. Turn the control dial, select [RX] or [TX] and then press the control dial. • The setting is complete. 2. 3. 4. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [RESET] and then press the control dial. Turn the control dial, select [Yes] and then press the control dial. After the confirmation screen is displayed, turn the control dial again to select [Yes] and then press the control dial. • Reset starts. Setting the display brightness 2. 3. The default setting is [High]. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [BRIGHTNESS] and then press the control dial. Turn the control dial, select [High] or [Low] and then press the control dial. • The setting is complete. Checking the receiver information This function displays the receiver information. 2. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [VERSION]. Setting the user access level Set the user access level. • The default setting is [Free Tuning]. 2. 3. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [ACCESS] and then press the control dial. Turn the control dial, select [Free Tuning] or [User Group Only] and then press the control dial. Free Tuning User Group Only No limit Selection of frequency can be made only from user groups (Ul and IJ2). • The setting is complete. 19

****** Page 21 ****** Setting ATW-T3201/ATW-T3202 List of setting items Setting by group/channel FREQUENCY MANUAL Gr/Ch NAME GAIN RF POWER HPF LOCK Fn BUTTON MUTE MODE (ATW-T3201 Set the transmission frequency. Set the channel name. Set the gain. Set the transmission output. Set HPF (High-Pass Filter). Set a lock. Set the function allocation for function button. Set the mute mode. Set the type of batteries used. Set whether to constantly keep indicator turned on or off. Set the user access level. This returns the transmitter settings to their factory defaults. It shows the version of the transmitter. 1 2. From the menu screen, press the UP/DOWN button to select [FREQUENCY], and then press the SET button. FREQUENCY OOO . OOO MHz After selecting [Gr/Ch], press the SET button. only) UTILITIES BATTERY LED ACCESS RESET VERSION Setting the transmission frequency Setting manually From the menu screen, press the UP/DOWN button to select FREQUENCY Gr/Ch 3. Press the UP/DOWN button to set the group. After completing the setting, press the SET button. 4. Press the UP/DOWN button to set the channel. After completing the setting, press the SET button. • The setting is complete. Setting the channel (transmitter) name The following characters can be entered: e maximum number of characters that can be entered is 8. 2. 3. 4. [FREQUENCY], and then press the SET button. FREQUENCY OOO .OOO MHz After selecting [MANUAL], press the SET button. FREQUENCY MANUAL Press the UP/DOWN button to set the first 3 digits. After completing the setting, press the SET button. Press the UP/DOWN button to set the last 3 digits. After completing the setting, press the SET button. • The setting is complete. Alphabetic (Uppercase letters) Numeric 2. 3. 4. 5. Symbols (+, —, #, &, period) Space From the menu screen, press the UP/DOWN button to select [NAME], and then press the SET button. NAME Press the UP/DOWN to select a desired character and press the SET button. • The character is input and the cursor moves. Repeat the operation in Step 2 to enter all characters. • If you donlt enter 8 characters, press the UP/DOWN button and select [Endl and then press the SET button. After entering the 8th character, press the SET button. • [Endl is displayed. Press the SET button. • The setting is complete. 20

****** Page 22 ****** Setting ATW-T3201/ATW-T3202 Setting the gain Setting lock 2. 3. From the menu screen, press the UP/DOWN button to select [GAIN], and then press the SET button. GAIN OdB Press the UP/DOWN button to select the gain you wish to set. • The level changes 2dB +/- each time you press the UP/DOWN button. • It can be set from -10 to +20 dB. Press the SET button. • The setting is complete. From the menu screen, press the UP/DOWN button to select [LOCK], and then press the SET button. LOCK Unlock Press the UP/DOWN button to select [Lock] or [Unlock]. 2. 3. Lock Unlock Locks transmitter buttons Unlocks transmitter buttons Press the SET button. • The setting is complete. Setting the RF transmission output 2. 3. From the menu screen, press the UP/DOWN button to select [RF POWER], and then press the SET button. RF POWER High:30mW Press the UP/DOWN button and select [High:30mW], [Low:10mWl or [Off]. Press the SET button. • The setting is complete. Setting the function for the function button Select the function to be performed when the function button is pressed and held. From the menu screen, press the UP/DOWN button to select [Fn BUTTON], and then press the SET button. Fn BUTTON Disable 2. Press the UP/DOWN button to select the function you wish to Setting HPF (High-Pass Filter) set. Disable Mute (only for ATW-T3202) MuteOnLock (only for ATW-T3202) Bkup Freq R F Off No function Mutes the transmitter Mutes the transmitter (even when transmitter buttons are locked) Switches to backup frequency (When selected, set the frequency, group, and channel.) Turns off RF transmission output 2. 3. From the menu screen, press the UP/DOWN button to select [HPF], and then press the SET button. HPF Off Press the UP/DOWN button to select [On] or [Off]. Press the SET button. • The setting is complete. 3. 21 Press the SET button. • The setting is complete.

****** Page 23 ****** Setting ATW-T3201/ATW-T3202 Set the function of the MUTE switch. From the menu screen, press the UP/DOWN button to select [MUTE MODE], and then press the SET button. MUTE MODE Mute 2. Press the UP/DOWN button to select the mode you wish to set. Setting the indicator The indicator LED can be turned [Onl or [Off]. Mute MuteOnLock Disable Mutes the transmitter Mutes the transmitter (even when transmitter buttons are locked) Disables the MUTE switch 3. Press the SET button. • The setting is complete. 1 2. 3. 4. The default setting is IOnl. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button. UTILITIES Press the UP/DOWN button to select [LED] and press the SET button. LED On Press the UP/DOWN button to select [On] or [Off]. Press the SET button. • The setting is complete. Setting the system-related functions Setting the battery type Set the type of batteries used. • The default setting is [Alkaline]. Setting the user access level Set the user access level. The default setting is [Free]. 2. 3. 4. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button. UTILITIES Press the UP/DOWN button to select [BATTERY] and press the SET button. BATTERY Alkaline Press the UP/DOWN button to select the battery you wish to set. 1 2. 3. 4. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button. UTILITIES Press the UP/DOWN button to select [ACCESS] and press the SET button. ACCESS Free Press the UP/DOWN button to select [Free] or [UserGroup]. Free UserGroup Alkaline NiMH Select when using alkaline batteries. Select when using nickel—metal hydride batteries. No limit Selection of frequency can be made only from user groups (Ul and U2). Press the SET button. • The setting is complete. • If the appropriate setting is not made for the batteries used, the battery power indicator will not display the correct information. Always set the type of battery according to the batteries used. Press the SET button. • The setting is complete. 22

****** Page 24 ****** Setting ATW-T3201/ATW-T3202 Resetting This returns the transmitter settings to their factory defaults. 2. 3. 4. 5. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button. UTILITIES Press the UP/DOWN button to select [RESET] and press the SET button. RESET No Press the UP/DOWN button to select [Yes]. When the confirmation screen is shown, press the UP/DOWN button again to select [Yes]. Press the SET button. • Reset starts. Checking the transmitter information This function displays the firmware version for the transmitter. 2. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button. UTILITIES Press the UP/DOWN button to select [VERSIONI and press the SET button. • The version is shown. VERSION ooo.ooo.ooo 23

****** Page 25 ****** How to attach the transmitter (ATW-T3201 ) The ATW-T3201 transmitter is equipped with a clip that can be used to attach the transmitter to a belt, etc. You can reverse the direction of the input connector by attaching the clip in the opposite direction. Pull both sides of the clip firmly to the outside to remove the clip from the product. Making connections (basic connections) This is an example of connections made when using one receiver. When connecting more than one receiver via a distributor (sold separately), refer to the distributor’s user manual. Whip antenna O ANT B Whip antenna UNBAL O o LIFT GND BAL AF OUTPUT 12V ANT 24 Mixer input AC adapter

****** Page 26 ****** Using IR SYNC This function allows you to make settings on the receiver that are specified for the transmitter. 1. 2. 3. 4. When IR SYNC is started as part of setting the receiver, the “Communication in standby” screen is displayed. Position the IR sync windows of the receiver and transmitter so they face each other. Press the SYNC button on the transmitter. • Wait several seconds until communication is established. When the SYNC is complete, the “completed” screen is displayed. • The settings made on the receiver are automatically synced to the transmitter. • If an error occurs in the SYNC process, an error screen opens and then the display returns to the menu screen. Check the IR SYNC windows of the receiver and transmitter and then SYNC again. • To cancel the SYNC process, press the BACK button on the receiver. You will be returned to the previous screen. Achieving stable reception Low RF signal may result if there are obstructions between receiver antennas and transmitter(s). In such a case, reposition the antennas to get better reception. Use external antennas (sold separately) if the installation space is limited. Rack-mounting the receiver • Screws for rack-mounting the receiver are not included. • Consider ventilation when rack-mounting to avoid heat building up in the rack. 25

****** Page 27 ****** Troubleshooting ATW-R3210 Symptoms The power cant be turned on. There is no voice output. The voice output level is low. Sound is distorted. There is unwanted noise. ATW-T3201/ATW-T3202 Symptoms The power can’t be turned on. There is no voice output. The voice output level is low. Sound is distorted. There is unwanted noise. Causes and countermeasures Confirm that the AC adapter is correctly connected. Confirm that the transmitter/receiver channels are correct Confirm that the power buttons of the transmitter/receiver are not turned OFF. Confirm that the antennas are correctly connected. Confirm that all connected components, such as a mixer, are correctly connected to tho receiver Confirm that the audio output isn’t set to the minimum level. Confirm that the audio output level of connected components (such as a mixer) is not minimized. Confirm that the audio output level isnlt too high. Confirm that the volume of any connected component isn’t too high. Confirm that there is no noise source, such as a fluorescent lamp or electric component, near the receiver. Confirm that each transmitter is using a different frequency: Confirm that the output terminal of the receiver is correctly connected. Confirm that the receiver isnlt taking power from an electrical outlet that is also being used by another noisy component. Confirm that there isn’t any other nearby wireless system using the same frequency band. Adjust the squelch level. Causes and countermeasures Confirm that batteries are in place. Confirm that batteries are not depleted Confirm that batteries are inserted in the right direction. Confirm that the transmitter/receiver channels are correct Confirm that the power switch is not turned OFE Confirm that RF Power isn’t OFF. Confirm that the transmitter isn’t in mute mode. Confirm that the transmission output of the transmitter is not too low. Confirm that the microphone or the guitar cable is not disconnected (only for ATW- T3201). Confirm that the output volume of the musical instrument, such as a guitar, isnlt set at the minimum level, Confirm that the microphone capsule is connected properly (only for ATW-T3202). Confirm that the gain setting of the transmitter is not too high. Confirm that there is no noise source, such as a fluorescent lamp, LED lamp, or electric component, near the transmitter. Confirm that each transmitter is using a different frequency. Confirm that the transmission output setting of the transmitter is not too high. 26 Reference page p. 15, p. 20 p. 13 p. 16 p. 16 p. 24 p. 17 Reference page p. 15, p. 20 p. 13 p. 21 p. 21 p. 21 p. 21 p. 21

****** Page 28 ****** Dimensions ATW-R3210 ANT D SYNC UNBAL 210.0 27 LIFT GND BAL AF OUTPUT UHF SYNTHESIZED RECEIVER BACK AIW-m•tO PUSH ENTER (Unit: mm)

****** Page 29 ****** Dimensions ATW-T3201 (D G) ATW-T3Z01 UHF TRANSMITTER audio-technica ATW-T3202 193 28 (Unit: mm) (Unit: mm)

****** Page 30 ****** Specifications Overall system specifications Operating frequencies” Band DE2: Band EEI. Band EFI : Band FGI: Minimum frequency step Modulation mode Maximum deviation Dynamic range Total harmonic distortion Operating range’? Frequency response *3 Maximum simultaneous use (recommended)’4 Frequency range 470.125 to 529.975 MHz 530.000 to 589.975 MHz 590.000 to 649.975 MI-Iz 650.000 to 699.875 MHz Number of frequencies 2,395 2,400 2,400 1 996 25 kHz ATW-T3201: +38 kHz (THD•.IOO/O) ATW-T3202: +36 kHz ATW-T3201 Mic input: 115 dB or higher (A-weighted), typical ATW-T3201 Inst input: 112 dB or higher (A-weighted), typical ATW-T3202: 115 dB or hiqher (A-weiqhted), typical I -0 % or less (at I kl-lz, ± 17.5 kHz deviation) 100 m (328) ATVV-T3201: 31 Hz to 15,500 Hz ATW-T3202: 25 Hz to 16,700 Hz 40 channels per band ‘5 *I Please note that some frequency bands might not be available in your territory or could come with a limited tuning bandwidth/transmitting power due to local regulations. *2 Open range environment with no interfering signals. *3 Frequency response depends on attached microphone element. *4 For assistance with mufti-band operation or other frequency coordination issues, Contact your local audio-technica dealeL *5 Region and band dependent ATW-R3210 Receiving system Image rejection RF sensitivity Maximum output level Antenna input Antenna power Power supply Operating temperature range Dimensions Weight (without accessories) Included accessories ATW-T3201 RF output power Spurious emissions Input connection 2 High-pass (low-freq. roll-off) Batteries Battery life* Dimensions Weight (without batteries) Operating temperature range True diversity 60 dB nominal 20 dBuV at 60 dBA S/N ratio (50 ohms termination) XLR, Balanced, +14 dBV 6.3 mm (1/4″) , Unbalanced, +8 dBV BNC-type, 50 ohms 12 V DC, 160 mA (combined) 100 to 240 V AC (50/60 Hz) to 12V DC 1 A (center positive) switched mode external power supply -5 oc to +45 oc (23 0 Fto 113 OF) 210.0 mm (8.27′) x 191 .O mm (7.52′) x 43.4 mm (1.71″) (W x D x H) 1,100 g (38.8 oz) Rack-mount (large, small), Rack-mount screw set, Flexible UHF antenna x 2, AC adapter (country dependent) 4 3 High: 30 mVV, Low: 10 mw (switchable), at 50 ohms Following federal and national regulations Four pin locking connector Pin 1: GND Pin 3: MIC INPUT 125 1-4zr 12 dB/octave Two 1.5V AA, not included High: 8.0 hours (alkaline) High: 9.0 hours (Ni-MH 11900 mAh) Pin 2: INST INPUT Pin 4: DC BIAS +5 V Low: 9.0 hours (alkaline) Low: 9.5 hours (Ni-MH 11900 mAh) 64 mm (2.52′) x 82 mm (3.22’) x 23 mm (0.91″) (W x D x H) 102 g (3.6 oz) -5 oc to +45 oc (23 0 F to 113 OF) * Depending on battery type, usage and environmental conditions. 29

****** Page 31 ****** Specifications ATW-T3202 RF output power Spurious emissions Microphone capsule High-pass (low-freq. roll-oft) Batteries Battery life* Dimensions Weight (without batteries) Operating temperature range Included accessories High: 30 mW, Low: 10 mw (switchable), at 50 ohms Following federal and national regulations Interchangable industry standard thread 1 50 6dB/octave Two 1.5V AA, not included High: 8.0 hours (alkaline) High: 9.0 hours (Ni-MH) Low: 9.0 hours (alkaline) Low: 9.5 hours (Ni-MH) ATW-T3202 (without capsule): 193 mm (7.60″) long, 37 mm (I .46″) maximum diameter AIW-T3202/C510: 265 mm (10.43″) long, 54 mm (2.13″) maximum diameter AIW-T3202/C710: 271 mm (10.67′) long, 50 mm (1.97″) maximum diameter AIW-T3202 (without capsule): 200 g (7.1 oz) AIW-T3202/C510: 330 g (1 1.6 oz) AIW-T3202/C710: 314 g (11.1 oz) -5 oc to +45 oc (23 0 Fto 113 OF) AT8456a Quiet-Flex TM stand clamp (5/80-27 male to 3/80-16 female threaded screw adapter) * Depending on battery type, usage and environmental conditions. For product improvement, the product is subject to modification without notice. 30

****** Page 32 ****** Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan audio-technica.com 02018 Audio-Technica Corporation Global Support Contact: at-globalsupport.com 2324169600201 ver.1 2018.04.15

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



AUDIO-TECHNICA ATW-R3210 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.