Click here to download AT&T TL92278 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** at&t User’s manual TL92278/TL92378/ TL92328 DECT 6.0 cordless answering system with Bluetooth wireless technology 3 at&t — DELETE PAUSE 44 at&t ANSWER 88 O Bluetm:jth REPEAT cuca SETUP ANNV

****** Page 2 ****** Model Type: Serial Congratulations on your purchase of this AT&T product. Before using this AT&T product, please read the Important safety information on pages XX-XX of this manual. Please thoroughly read this user’s manual for all the feature operations and troubleshooting information necessary to install and operate your new AT&T product. You can also visit our website at telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. TL92278 (two handsets) TL92378/TL92328 (three handsets) DECT 6.0 cordless telephone answering system with Bluetooth wireless technology Purchase date: Place of purchase: Both the model and serial number of your AT&T product can be found on the bottom of the telephone base. Save your sales receipt and original packaging in case jt is necessary to return your telephone for warranty service. The ENERGY STARO program (energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STARO label indicating it meets the latest energy efficiency guidelines. 0 2008 Advanced American Telephones. A I rights reserved AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, LP d/b/a AT&T Intellectual Property licensed to Advanced American Telephones. Printed in China

****** Page 3 ****** Before you begin you must install and charge the battery, see page XX for Battery installation instructions. Please read and follow these instructions carefully: • Use only the supplied rechargeable battery or replacement battery. • Observe the proper polarity orientation between the battery and handset during battery installation. • Do not dispose of the battery in a fire. Check with local codes for special disposal instructions. • Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. • Exercise care in handling batteries in order not to create a short circuit with conductive materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. • Charge the supplied battery or replacement battery with this product only in accordance with the instructions and limitations specified in this manual. • Do not disassemble your telephone. There are no user- serviceable parts inside. Refer to qualified service personnel for servicing. 3

****** Page 4 ****** Parts checklist Your telephone contains the following items. at&t 3.8 GHz #tal 5FtK•m BLUETOOTH’ wirQz.5 User’s manual at&t at&t 3.8 GHz digital with u-ETOOTH• wirdzs Quick start guide 3 atat Cordless handset (2 for TL92278) (3 for TL92378/ TL92328) atgt 88 Telephone base Battery compartment cover (2 for TL92278) (3 for TL92378/ TL92328) Charger for cordless handset with power adapter installed (1 for TL92278) (2 for TL92378/ TL92328) Wall mount bracket Battery for cordless handset (2 for TL92278) (3 for TL92378/ TL92328) Telephone line cord

****** Page 5 ****** User’s manual TL92278/TL92378/TL92328 …. ….35 . …20 . …51 DECT 6.0 cordless answering system with Bluetooth@ wireless technology Table of contents Getting started Quick reference guide handset. telephone base. Handset status icon Installation setup at&t are e e 6. O Chain dialing. Intercom at&t n•.snp 88 -.37 38 .3 4 6 5 .9 Call transfer using intercom ……40 Directory About the directory 31 Creating directory entries 32 Telephone base installation……… 6 Charger installation…………. . Battery installation & charging… Installation options….„………… .. …10 Expansion handset 15 Adding & registering handsets …..16 Replacing a handset Bluetooth Introducing Bluetooth 19 Directory review…….. Directory search……………. To dial, delete or edit entries Caller ID Caller ID operation .-34 -36 37 Glossary of terms Bluetooth setup Handset settings Handset main menu……………… Handset settings….. Telephone operation Handset operation Options while on calls…. 21 …22 28 .34 To review the caller ID h istory …………………………… Answering system About the answering system… Day & time announcement….. …42 Answering system mode. Outgoing announcements 45 Answering system setup…………..47 Message playback. Recording & playing memos-…..52 Message counter displays……… .53 Remote …54 5

****** Page 6 ****** Table of contents Appendix A, Alert tones and lights. Appendix B, Handset display screen messages 71 Appendix C, Maintenance 74 Appendix D, Important safety information ….75 Appendix E, FCC Part 68 and ACTA 78 Appendix F, FCC Part 15 80 Appendix G, Limited warranty…………………….81 Appendix H, Technical specifications 71 Appendix I, Troubleshooting. Index 80

****** Page 7 ****** Getting started Quick reference guide – handset CHARGE indicator On when the handset is charging in the telephone base or charger. DIR / CID Press t) DIR to display directory entries (page 34). Press to scroll up while in menus. While entering names or numbers, press to move the cursor to the right. Press to increase the listening volume when on a call. Press CID to display caller ID history (page 40). Press to scroll down while in menus. While entering names or numbers, press to move the cursor to the left. Press to decrease the listening volume when on a call. REDIAL/PAUSE Press to view redial memory (page 22). While entering numbers, press and hold to insert a dialing pause (page 32). ÆHOME/FLASH Press to make or answer a HOME call Flashes rapidly when there is an incoming HOME calL Flashes slowly when a HOME call is on hold. During a HOME call, press to REDIAL PAUSE ORS SPEAKER e at&t U/SELECT DIRA VOLUME CIDV DELETE MUTE CLEAR xyz C%LLULAR O HOLD OSPEAKER Press to turn on the handset MENU/SELECT Press to display the menu. While in the menu, press to select an item or save an entry or setting. DELETE/MUTE During a call, press to mute microphone (page 25). While reviewing the caller ID history, press to delete an individual entry, or press and hold to clear the caller ID history (page 40). While predialing, press to delete digits (page 21). ÉOFF/CLEAR During a HOME or CELLULAR line call, press to end the call. While in a menu, press to cancel an operation, back up to the previous menu, or exit the menu display. CELLULAR Press to make or answer a CELLULAR call. Flashes rapidly when there is an incoming CELLULAR call Flashes slowly when a CELLULAR call is on hold. During a CELLULAR call, press to receive an incoming call if call waiting is activated (page 57). HOLD Press to put the HOME or CELLULAR call on hold. receive an incoming call if call speakerphone. waiting is activated Press again to resume normal (page 57). handset use (page 21). 1

****** Page 8 ****** Getting started Quick reference guide – handset Feature menu The > symbol shows a highlighted menu item. 3 at&t Menu Feature menu DIRECTORY (page 34) CALL LOG (page 40) INTERCOM (page XX) RINGER VOLUME (page 16) RINGER TONE (page 17) KEY TONE (page 17) LANGUAGE (page 18) CLR VOICE MAIL (page 19) HOME AREA CODE (page XX) 2 Using menus or to scroll Press through menu items. Press MENU/SELECT to select or save changes to a highlighted menu item. Press É0FF/CLEAR to cancel an operation, back up to the previous menu, or exit the menu display. REDIAL DELETE PAUSE MUTE VOLUME

****** Page 9 ****** Getting started Quick reference guide – telephone base IN USE indicator On when the handset is in use, when the answering system is answering an incoming call or when you are registering a handset. Flashes when another telephone is in use on the same line, or you are deregistering handset(s) from the telephone base. Flashes quickly when there is an incoming call. MESSAGE COUNTER Number of messages (or during playback, message number currently playing). ANSWER ON Press to turn the answering system on or off (page 44). X/DELETE Press to delete the message currently playing. Press twice to delete all old messages when the phone is not in use (page 51). O BLUETOOTH Press to enable the Bluetooth feature on the telephone base. On when the telephone base is paired and connected with a cellular phone. Flashes when the telephone base is paired but not connected with a cellular phone. CLOCK Press to review or set the clock (page 42). at&t CEMAIL ANSWER ON d) O Bluetooth’ —IN USE CLOCK Pl-AWSTOP DELETE REPEAT HANDSET LOCATOR SKIP RECORD ) nswering System Functions at&t VOICEMAIL SWER ON d) IN USE CLOCK PLAY/STOP 88 DELETE SETUP REPEAT HANDSET LOCATOR ANNC. SKIP RECORD EXPANDABL SETUP Press to hear and change setup options (page 47). 3 VOICEMAIL indicator Flashes when you have new voicemail. Voicemail is a service offered by your local telephone company, and is different from answering system messages (page 19). HANDSET LOCATOR Press to make handsets beep so you can locate them (page 23). PLAY/STOP Press to start or stop message playback (page 51). «/REPEAT Press to repeat a message. Press twice to play the previous message (page 51). »/SKIP Press to skip a message (page 51). RECORD Press to record a memo (page 52) or, after pressing ANNC to record an outgoing announcement (page 45). ANNC. Press to review or record the outgoing announcement. Press again to end announcement playback or recording (page 45).

****** Page 10 ****** Getting started Handset status icons H HND 5 E T I 25 M155ED CHLL5 fiÆ(p) MUTE 10:21 MUTE NEW HOME line on steady when the HOME line is in use. CELLULAR line on steady when the CELLULAR line is in use. BLUETOOTH – on steady when a cellular phone is connected with the telephone base- NEW VOICE MAIL €- new voicemail received from the local telephone company. SPEAKERPHONE – the speakerphone is in use. Ringer off – the handset ringer is turned off Battery status battery is charging (animated display). Battery status – low battery (flashing); place handset in telephone base or charger to recharge. Microphone is muted. Missed and unreviewed calls. 4

****** Page 11 ****** Getting started Installation setup You must install and charge the handset battery before using the cordless handset. STOP/ See page 8 for easy instructions. Install the telephone base close to a telephone jack and a power outlet not controlled by a wall switch. The telephone base can be placed on a flat surface or vertically mounted on the wall (see page 10). For optimum range and better reception, place the telephone base in a central and open location. Depending on the environmental conditions, make sure that your Bluetooth enabled cellular phone is within 12 feet of where you install the telephone base in order to maintain a reliable connection between your Bluetooth cell phone, telephone base, and cell tower. If you subscribe to high-speed Internet service (Digital Subscriber Line -u DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack (see the following page). The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. Your product may be shipped with a protective sticker covering the handset or telephone base display – remove it before use. For customer service or product information, visit our website at wwwetelephones.attecom or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268 Avoid placing the telephone base too close to: • Communication devices such as: television sets, VCRs, or other cordless telephones. Excessive heat sources. • Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting. Excessive dust sources such as a workshop or garage. Excessive moisture. • Extremely low temperature. • Mechanical vibration or shock such as on top of the washing machine or work bench. 5

****** Page 12 ****** Getting started Telephone base installation Install the telephone base as shown below. Make sure that the electrical outlet is not controlled by a wall switch. If you subscribe to high-speed Internet service (Digital Subscriber Line -u DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack. The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. The telephone base is set for desktop use. If you want to change to wall mounting position, you will need to install the provided bracket to the telephone base, see page 10 for details. 1. Plug one end of the telephone line cord into the telephone jack at the bottom of the telephone base (if necessary). 5. Plug the large end of the power adapter into a power outlet not controlled by a wall switch. Power adapter 2. Plug the small end of the power adapter into the power Jack at the bottom of the telephone base. 3. Route cords through slots. 4. e e Plug the other end of the telephone line cord into a telephone Jack. e Telephone line cord DSL filter (not included), required if you have DSL high-speed Internet service. 6. Raise the antenna. •tat 6 at&t

****** Page 13 ****** Getting started Charger installation Plug the power adapter into an electrical outlet not controlled by a wall switch. IMPORTANT INFORMATION 1. Use only the power adapter(s) supplied with this product. To order a replacement power adapter, visit our website at telephones.att.com, or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268 2. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 7

****** Page 14 ****** Getting started Battery installation & charging Install the battery as shown below. After installing the battery, you can make and receive short calls, but replace the handset in the telephone base or charger when not in use. For optimal performance, charge the handset battery for at least 16 hours before use. When fully charged, the handset battery provides approximately five hours of talk time or three days of standby time. Step O Press the depression and slide the battery compartment cover downwards (if necessary). Step O Step Plug the battery securely into the connector inside the handset battery compartment, matching the color-coded label. Insert the supplied battery with the label THIS SIDE UP facing up as indicated. Step @ Align the cover flat against the battery compartment cover, then slide it upwards until it clicks into place. aut at&t 88 Charge the handset by placing it face up in the telephone base or charger. The CHARGE light will be on when charging. IMPORTANT INFORMATION Use only the supplied rechargeable battery or replacement battery (model BT8001). To order, visit our website at telephones.att.com or call 1 (800) 222- 3111. In Canada, dial 1 (866) 288-4268. 8

****** Page 15 ****** Getting started Installation options The telephone base is set for desktop use. It is possible to change to wall mounting position by installing the bracket provided. Wall mounting requires a telephone outlet wall mounting plate with mounting studs that may require professional installation. You can purchase the mounting plate from many hardware or consumer electronics retailers. Desktop to wall mount installation To change the telephone base to the wall mount position, make sure that you first unplug the telephone line cord and power adapter cord from the wall outlets before you begin. 1. Position the telephone base as shown below, and insert the extended tabs of the bracket into the slots under the telephone base. 2. Push down the telephone base until it clicks into the catches on both sides of the bracket. 9

****** Page 16 ****** Getting started Installation options Desktop to wall mount installation 3. Bundle the telephone line cord and power adapter cord, and secure them with a twist tie before placing them behind the telephone base as shown below. 4. Align the holes on the bracket with the standard wall plate and slide the bracket until the telephone is secured as shown below. Plug the telephone line cord into a telephone wall jack. Plug the power adapter into an power outlet not controlled by a wall switch. 10

****** Page 17 ****** Getting started Installation options Desktop to wall mount installation 5. Make sure the telephone is securely positioned as shown below. 11

****** Page 18 ****** Getting started Installation options Wall mount to desktop installation To change the telephone base to the desktop position, make sure that you first unplug the telephone line cord and power adapter cord from the wall outlets before you begin. 1. Remove the telephone base from the wall and untie the bundled telephone line cord and power adapter cord. 2. Press on the catches on both sides of the bracket (indicated by arrows below) to unlock the telephone base from the bracket. The catch on the side of the telephone base. 88 0 0 80Jetootih 3. Pull the telephone base up to detach it from the bracket. 12


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

AT&T TL92278 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.