Click here to download AT&T TL86109 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** at&t User’s manual TL86009 DECT 6.0 expansion handset for use with AT&T model TL86109 corded/cordless telephone/ answering system with BLUETOOTH@ wireless technology 3 at&t at&t

****** Page 2 ****** Congratulations on purchasing your new AT&T product. Before using this AT&T product, please read Important safety information on pages 24-26. For complete instructions, please refer to the manual provided with your TL86109 telephone. For customer service or product information, please visit our website at telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. This telephone meets the California Energy Commission regulations for energy consumption. Your telephone is set up to comply with the energy-conserving standards right out of the box. No further action is necessary. Model Type: Serial # Purchase date: Place of purchase: TL86009 DECT 6.0 expansion handset Both the model and serial numbers of your AT&T product can be found on the bottom of the charger. Save your sales receipt and original packaging in case it is necessary to return your telephone for warranty service. Compatible with Hearing Aid T-Coil TIA-1083 ENERGY STAR Telephones identified with this logo have reduced noise and interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license. The ENERGY STARS program (energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STARS label indicating it meets the latest energy efficiency guidelines. The Bluetooth’ word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by Advanced American Telephones and its parent, VTech Holdings Limited, is under license. VTech Holdings Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. 0 2010-2014 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219. Printed in China.

****** Page 3 ****** Parts checklist Your telephone package contains the following items. at&t User’s manual TLSSCOE CECT E.’ far un wtth ATAT madel TLEEIOE I.eph sisterr v.*i SLUETOOTHt• User’s manual Battery for cordless handset at&t Cordless handset Battery compartment cover Charger for cordless handset with power adapter installed 3 at8t Belt clip for cordless handset

****** Page 4 ****** Table of contents Getting started Installation 1 Quick reference guide …. ….. …… 2 Charger installation………………… 5 Battery installation and charging .6 Battery charging ………………….. 8 Belt clip & optional headset… 9 Adding handset to your telephone base Adding and registering handsets Expand your telephone Add and register a handset………………………………..ll Replace a handset …………………12 Appendix Troubleshooting Maintenance-……………………………23 Important safety information………………………………24 Safety information…………….24 Especially about corded telephones .. 25 User’s manual at&t TL86009 DECT 6.0 expansion handset for use with AT&T model TL86109 corded/cordless telephone/ answering system with BLUETOOTH@ wireless technology at&t .. 11 ……………………..13 38 Precautions for users of implanted cardiac pacemakers …. ….. ….. ….. .. ….. .. 26 Pacemaker patients………….26 Especially about telephone answering systems……………26 For C-UL compliance……………..27 Mesures de sécurité importantes…………………………27 FCC Part 68 and ACTA………….30 FCC Part 15 32 California Energy Commission battery charging testing instructions………………………………..33 Limited 34 Technical specifications ……….37 DECT 6.0 digital techno logy 37 Telephone operating 38 Extended range and

****** Page 5 ****** Getting started Installation You must install and charge the handset battery before using the cordless handset. See pages 6-8 for easy STOP! instructions. Your product may be shipped with a protective sticker covering the handset display – remove it before use. For customer service or product information, visit our website at telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Avoid placing the telephone base too close to: Communication devices such as television sets, VCRs, or other cordless telephones. Excessive heat sources. Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting. Excessive dust sources such as a workshop or garage. Excessive moisture. Extremely low temperature. Mechanical vibration or shock such as on top of the washing machine or work bench. 1

****** Page 6 ****** Getting started Quick reference guide Softkeys (2) Press to select a menu item displayed above the key. CHARGE light (blue ring around DIR/A/VOL/V/CID) On when the handset is charging in the charger. DIR/A/VOL Press to scroll up while in menus. Press to increase the volume level during a call. Press to show directory entries when the telephone is not in use. While entering names or numbers, press to move the cursor to the right. (P)CELL Press to make or answer a cell call. Flashes quickly when there is an incoming cell call. Flashes slowly when a cell call is on hold. LINE PORS at&t ABC JKL ..OFF/CLEAR While using menus, press to cancel an operation, back up to the previous menu, or exit the menu display. Press and hold to return to idle mode. While entering names or numbers, press to delete a digit or a character. During a call, press to hang up. VOL/Y/CID Press to scroll down while in menus. Press to decrease the volume level during a call. Press to show the caller ID history when the telephone is not in use. While entering names or numbers, press to move the cursor to the left. TONE SPEAKER HOLO O Bluetooth’ 2

****** Page 7 ****** Getting started Quick reference guide 1 While reviewing a caller ID history entry, press repeatedly to add or remove 1 in front of the telephone number before dialing or saving it in the directory. TONE Press to switch to tone dialing temporarily during a call if you have pulse service. O/SPEAKER Press to turn on the handset speakerphone. Press again to resume normal handset use. HOLD Press to put a call on hold. GHI PORS 3 at&t CIO ABC JKL OPER LINE DEF MNO REDIAL 1 LINE/FLASH/ 2 LINE/FLASH Press 1 LINE/FLASH to make or answer a call on line 1. During a call, press to answer an incoming call on line 1 when you receive a call waiting alert. Press 2 LINE/FLASH to make or answer a call on line 2. During a call, press to answer an incoming call on line 2 when you receive a call waiting alert. Press repeatedly to display other dialing options when reviewing a caller ID history entry. REDIAL/PAUSE Press to view the redial list. While entering numbers, press and hold to insert a dialing pause. 0 Bluetooth’ 3

****** Page 8 ****** Getting started Quick reference guide 1 at&t HANCEET MENi-i at&t During an outside call, intercom call, message or announcement playback, press to change the quality of the audio to best suit your hearing. Press the MENU softkey to enter the main menu which includes the following: PLAY MESSAGES ANSWERING SYS DIRECTORY CALL LOG INTERCOM RINGER SETTINGS WEBSITE 4

****** Page 9 ****** Getting started Charger installation Install the charger, as shown below. Plug the power adapter into an electrical outlet not controlled by a wall switch. IMPORTANT INFORMATION: 1. Use only the power adapter provided with this product. To obtain a replacement, visit our website at telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 2. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 5

****** Page 10 ****** Getting started Battery installation and charging Install the battery, as shown below. step 1 Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-coded label. Insert the supplied battery with the label THIS SIDE UP facing up, as indicated. step 3 Charge the handset by placing it face up in the charger. The CHARGE light is on when charging. 6 step 2 Align the cover flat against the battery compartment, then slide it upwards until it clicks into place. aut CHARGE light 3 at&t

****** Page 11 ****** Getting started Battery installation and charging After you install your telephone or power returns following a power outage, the handset SET will prompt you to set the date and time. To skip setting the date and time, press ø—OFF/CLEAR. EET SET TIME To replace the battery, press the tab and slide 3 at’ t the battery compartment cover downwards. Lift out the old battery and disconnect it from the handset. Follow the instructions on page 6 to install and charge the new battery. IZI IMPORTANT INFORMATION: 1. Use only the supplied rechargeable battery or replacement battery (model BT166342/BT266342). To order, visit our website at telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 2. If you do not use the handset for a long time, disconnect and remove the battery to prevent possible leakage. 7

****** Page 12 ****** Getting started Battery charging Once you have installed the battery, the screen indicates the battery status (see the following table). If necessary, place the handset in the charger to charge the battery. For best performance, keep the handset in the charger when not in use. The battery is fully charged after 16 hours of continuous charging. See the table on page 37 for battery operating times. If the screen shows Low battery, you need to charge the battery without interruption for at least 25 minutes to give the handset enough charge to use the telephone for a short time. The following table summarizes the battery charge indicators and actions to take. Battery indicators The screen is blank or shows Place in charger. The screen shows Low battery and flashes. The screen shows HANDSET X. Battery status The battery has very little or no charge. The handset cannot be used. Battery has enough charge to be used for a short time. Battery is charged. Action Charge without interruption until the screen shows Low battery or HANDSET X (at least five minutes). Charge without interruption until the screen shows HANDSET X (at least 25 minutes). To keep the battery charged, place it in the charger when not in use. NOTE: If you are on a phone call in low battery mode, you hear four short beeps every minute. 8

****** Page 13 ****** Getting started Belt clip & optional headset 3 at8t To attach the belt clip: Snap the belt clip into the slots on both sides of the handset, as shown in the figure. To remove the belt clip: Gently lift either of the belt clip tabs, shown in the figure, outwards to remove the belt clip from the handset. For handsfree telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results, use an AT&T 2.5 mm headset. To purchase a headset, visit our website telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Plug a 2.5 mm headset into the Jack on the side of handset (beneath the small plastic cover). Lift the plastic cover here. 1 1 Side of handset 9 3 at&t

****** Page 14 ****** Adding handset to your telephone base Adding and registering handsets Before using a new TL86009 handset, you must register it with the AT&T TL86109 telephone system (purchased separately). The AT&T TL86109 telephone system can accommodate up to 12 handsets. The handset provided with the TL86109 comes registered as HANDSET. You can register up to 11 additional handsets to the telephone base, and they will be assigned numbers in the order they are registered (HANDSET 2, HANDSET 3, HANDSET 4 and so on). Your first handset is then renamed as HANDSET 1. 10

****** Page 15 ****** Adding handset to your telephone base Expand your telephone system Add and register a handset When first purchased, each expansion handset shows Press [HOLD] on base for 4 sec, then press on handset after a battery is installed. Each handset should be charged without interruption for at least 25 minutes before registering to the telephone base. For more details on battery charging, see the table on page 8. To register a handset: 1. Press and hold HOLD on the telephone base for about four seconds until it shows Registering…Please wait. Then, release the button. 2. Press # (pound key) on the handset. Its screen shows Registering handset… and it takes up to 60 seconds to complete the registration. The handset and telephone base HOLD atat .4 show HANDSET X Registered (X represents the handset number assigned) and you hear a beep when the registration completed. O NOTES: If the registration fails, the handset shows Registration failed for a few seconds and then Press [HOLD] on base for 4 sec, then press on handset. Try the registration process again. • You cannot register a handset if any other system handset is in use. • You cannot register more than 12 handsets to the telephone base. Registration slots are full shows on the base screen while you are in step 2. 11

****** Page 16 ****** Adding handset to your telephone base Replace a handset If you want to replace a handset or reassign the designated handset number of a registered handset, you must deregister all the handsets and then individually register each handset. To make deregistration easier, read all of the instructions on this page before you begin. To deregister all handsets: 1. Press and hold FLASH on the telephone base for about 4 seconds until it shows Deregister all handsets? Then, release the button. 2. Press the Yes softkey to continue. You hear a confirmation tone from the telephone base. 3. The telephone base displays PLEASE WAIT… All system handsets show Out of range OR no power at base for a few seconds, and then you hear a confirmation tone from the handset. 4. All the handsets show Press [HOLD] on base for 4 sec, then press on handset when the deregistration completed. The deregistration process takes about 10 seconds to complete. If deregistration fails, you may need to reset the telephone and try again. To reset: • Unplug the power from the telephone base, then plug it back in. After deregistering, register each handset individually. See Add and register a handset on page 11. NOTES: • You cannot deregister the handset(s) if any other system handset is in use. During deregistration, your DECT 6.0 headset(s) will also be deregistered. 12

****** Page 17 ****** Appendix Troubleshooting If you have difficulty with your telephone, please try the following suggestions. For customer service, or to purchase accessories or replacement parts, visit our website at telephones.att.com, or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. My phone doesn’t work at all. • Make sure the power cord is securely plugged in. • Make sure that the battery connector is securely plugged into the cordless handset. • Make sure the telephone line cord is securely and firmly plugged into the telephone cord line and the telephone wall jack. • Charge the battery in the cordless handset for at least 16 hours. For optimum daily performance, return the cordless handset to the charger when not in use. • If the battery is depleted, it may take approximately five minutes to charge the handset before it shows Low battery. See page 8 for details. • Reset the telephone base. Unplug the electrical power. Wait for approximately 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset. • You may need to purchase a new battery. Please refer to Battery installation and charging (pages 6-7) in this user’s manual. 13

****** Page 18 ****** Appendix Troubleshooting The display shows NO LINE. I cannot get a dial tone. • First try all the suggestions, as mentioned above. • If the previous suggestions do not work, disconnect the telephone line cord from your telephone and connect the telephone line cord to another telephone. • If there is no dial tone on that telephone either, your telephone line cord may be defective. Install a new telephone line cord. • If changing the telephone line cord does not help, the wall jack (or the wiring to this wall jack) may be defective. Try using a different wall jack in your home to connect your TL86109 telephone, or contact your telephone service provider (charges may apply). I cannot dial out. • First try all the suggestions in the above entry. • Make sure you have a dial tone before dialing. The cordless handset may take a second or two to find the telephone base and produce a dial tone. This is normal. Wait an extra second before dialing. • Eliminate any background noise. Noise from a television, radio or other appliances may cause the phone to not dial out properly. If you cannot eliminate the background noise, first try muting the cordless handset before dialing, or dialing from another room in your home with less background noise. • If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your telephone service provider (charges may apply). 14

****** Page 19 ****** Appendix Troubleshooting My cordless handset isn’t performing normally. • Make sure the power cord is securely plugged into the telephone base. Plug the power adapter into a different working electrical outlet not controlled by a wall switch. • Move the cordless handset closer to the telephone base. You might have moved out of range. • Reset the telephone base. Unplug the electrical power. Wait for 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset. • Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices. The handset registration is unsuccessful. Follow the steps to register the handset again. 1. Make sure the handset is out of the charger and shows Press [HOLD] on base for 4 sec, then press on handset before you begin. 2. Press and hold HOLD on the telephone base for about four seconds until it shows Registering…Please wait. Then, release the button. 3. Press # (pound key) on the handset. Its screen shows Registering handset… and it takes up to 60 seconds to complete the registration. The handset shows HANDSET X Registered (X represents the handset number assigned) and you hear a beep when the registration completed. Refer to Add and register a handset on page 11 for details. 15

****** Page 20 ****** Appendix Troubleshooting Out of range OR no power at base appears on my cordless handset. • Ensure that the telephone base is powered up. • Move the cordless handset closer to the telephone base. You might have moved out of range. • Reset the telephone base. Unplug the electrical power. Wait for 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset. • Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices. The batteries do not hold a charge. • If the cordless handset is in the charger and the charge light does not come on, refer to The charge light is off (page 21) in this Troubleshooting guide. • Charge the battery in the cordless handset for at least 16 hours. For optimum daily performance, return the cordless handset to the charger when not in use. • If the battery is depleted, it may take approximately five minutes to charge the handset before it shows Low battery. See page 8 for details. • You may need to purchase a new battery. Please refer to Battery installation and charging (pages 6-7) in this user’s manual. 16

****** Page 21 ****** Appendix Troubleshooting I get noise, static, or a weak signal even when I’m near the telephone base. • If you subscribe to high-speed Internet service (DSL -I digital subscriber line) through your telephone lines, you must install a DSL filter between each telephone line cord and telephone wall jack. The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. • You may be able to improve the performance of your cordless phone by installing your new telephone base as far as possible from any other existing cordless telephone system that may already be installed. • Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices. • Do not install this phone near a microwave oven or on the same electrical outlet. You may experience decreased performance while the microwave oven is operating. • If your phone is plugged in with a modem or a surge protector, plug the phone (or modem/surge protector) into a different location. If this doesn’t solve the problem, relocate your phone or modem farther apart from one another, or use a different surge protector. • Relocate your phone to a higher location. The phone may have better reception when installed in a high area. • If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your telephone service provider (charges may apply). 17

****** Page 22 ****** Appendix Troubleshooting I experience poor sound quality when using the speakerphone. • For increased sound quality while using the speakerphone, place the handset on a flat surface with the dial pad facing up. • When using a speakerphone, controlling background noise in your environment is essential. While you are listening to your party, press the MUTE softkey to temporarily turn your microphone off. When it is your turn to speak, remember to press the MUTE softkey again to turn the microphone on. • Excessive background noise will cause a speakerphone to fade in and out. Try controlling the background noise by turning off any audio devices near the speakerphone. Also, try to avoid interrupting the person at the other end of the conversation while they are speaking. If background noise cannot be controlled, you should terminate speakerphone operation and return to normal handset mode. I hear other calls while using my phone. • Disconnect the telephone base from the telephone jack, and plug in a different telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your telephone service providen While on a call or playing messages, there is too much noise, or the voice sounds tinny, shrill or flat. • While on a call or playing messages, press the EQ button on the side of the handset until you find the settings that sounds the best. 18

****** Page 23 ****** Appendix Troubleshooting My cordless handset does not ring when I receive a call. • Make sure that the ringer is not turned off. Refer to Ringer volume on your user’s manual. • Make sure the telephone line cord is plugged securely into the telephone base and the telephone jack. Make sure the power cord is securely plugged in. • The cordless handset may be too far from the telephone base. • Charge the battery in the cordless handset for at least 16 hours. For optimum daily performance, return the cordless handset to the charger when not in use. • You may have too many extension phones on your telephone line to allow all of them to ring simultaneously. Try unplugging some of the other phones. • The layout of your home or office might be limiting the operating range. Try moving the telephone base to another location, preferably to a higher location. • If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your telephone service provider (charges may apply). • Test a working phone at the phone jack. If the other phone has the same problem, the problem is the phone jack. Contact your telephone service provider (charges may apply). • Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices. • Remove and install the battery again. Wait for the cordless handset to reestablish its connection with the telephone base. Allow up to one minute for this to take place. • Your line cord might be malfunctioning. Try installing a new line cord. 19

****** Page 24 ****** Appendix Troubleshooting My calls cut in and out while I’m using my cordless handset. • Other electronic products such as HAM radios and other DECT phones, can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices. • Do not install this phone near a microwave oven or on the same electrical outlet. You may experience decreased performance while the microwave oven is operating. • If you plug your phone in with a modem or surge protector, plug the phone (or modem/surge protector) into a different location. If this doesn’t solve the problem, relocate your phone or modem farther apart from one another, or use a different surge protector. • Relocate your telephone base to a higher location. The phone may have better reception when installed in a high area. • If the other phones in your home are having the same problem, the problem is in your wiring or local service. Contact your telephone service provider (charges may apply). • Excessive background noise will cause a speakerphone to fade in and out. Try controlling the background noise by turning off any audio devices near the speakerphone. Also, try to avoid interrupting the person at the other end of the conversation while they are speaking. If background noise cannot be controlled, you should stop speakerphone operation and return to normal handset mode. • When using a speakerphone, controlling background noise in your environment is essential. While you are listening to your party, press the MUTE softkey to temporarily turn your microphone off. When it is your turn to speak, remember to press the MUTE softkey to turn the microphone on. 20

****** Page 25 ****** Appendix Troubleshooting The charge light is off. • Make sure the power and line cords are plugged in correctly and securely. • Unplug the electrical power. Wait for 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and telephone base to reset. • Clean the cordless handset and charger charging contacts each month using a pencil eraser or cloth. My caller ID isn’t working. • Caller ID is a subscription service. You must subscribe to this service from your telephone service provider for this feature to work on your phone. • The caller must be calling from an area that supports caller ID. • Both your and your caller’s telephone service providers must use caller ID compatible equipment. • If you subscribe to high-speed Internet service (DSL – digital subscriber line) through your telephone lines, you must install a DSL filter between each telephone line cord and telephone wall jack. The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. My telephone does not receive caller ID when on a call. • Make sure you subscribe to caller ID with call waiting features provided by your telephone service provider. Caller ID features work only if both you and the caller are in areas offering caller ID service, and if both telephone companies use compatible equipment. 21

****** Page 26 ****** Appendix Troubleshooting I subscribe to a nontraditional telephone service that uses my computer to establish connections, and my telephone does not work. • Make sure your computer is powered on. • Make sure your Internet connection is working properly. • Make sure that the software is installed and running for your nontraditional telephone service. • Make sure to plug your USB telephone adapter into a dedicated USB port on your computer Do not plug into a multiple port USB hub (USB splitter) that is not powered. • In a few rare instances, the USB port on your computer may not have enough power. In these instances, try using a USB hub with its own external power supply. • If you are using a firewall, it may prevent access to your nontraditional telephone service provider. Contact your service provider for more information. Common cure for electronic equipment: If the telephone is not responding normally, try resetting the telephone. Do the following in the order listed: 1. Disconnect the power to the telephone base. Disconnect the cordless handset battery. 2. 3. Wait a few minutes. 4. Connect power to the telephone base. 5. Install the battery again. 6. Wait for the cordless handset to reestablish its connection with the telephone base. Allow up to one minute for this to take place. 22

****** Page 27 ****** Appendix Maintenance Taking care of your telephone • Your cordless telephone contains sophisticated electronic parts, so it must be treated with care. • Avoid rough treatment. • Place the handset down gently. • Save the original packing materials to protect your telephone if you ever need to ship it. Avoid water • Your telephone can be damaged if it gets wet. Do not use the handset in the rain, or handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower. Electrical storms • Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take caution when using electric appliances during storms. Cleaning your telephone • Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft cloth slightly dampened with water or a mild soap. • Do not use excess water or cleaning solvents of any kind. Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then, pull the telephone out by the unplugged cords. 23

****** Page 28 ****** Appendix Important safety information This symbol is to alert you to important operating or servicing instructions that may appear in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock. Safety information • Read and understand all instructions in the user’s manual. Observe all markings on the product. Avoid using a telephone during a thunderstorm. There might be a slight chance of electric shock from lightning. Do not use a telephone in the vicinity of a gas leak. If you suspect a gas leak, report it immediately, but use a telephone away from the area where gas is leaking. If this product is a cordless model, make sure the base is also away from the area. Do not use this product near water, or when you are wet. For example, do not use it in a wet basement or shower, or next to a swimming pool, bathtub, kitchen sink, or laundry tub. Do not use liquids or aerosol sprays for cleaning. If the product comes in contact with any liquids, unplug any line or power cord immediately. Do not plug the product back in until it has dried thoroughly. Install this product in a protected location where no one can trip over any line or power cords. Protect cords from damage or abrasion. If this product does not operate normally, read the Troubleshooting section on pages 13-22 of this user’s manual. If you cannot solve the problem, or if the product is damaged, refer to the Limited warranty section on pages 34-36. Do not open this product except as may be directed in your user’s manual. Opening the product or reassembling it incorrectly may expose you to hazardous voltages or other risks. Replace batteries only as described in your user’s manual (pages 6-7). Do not burn or puncture batteries — they contain caustic chemicals. This power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under-the-table/cabinet outlet. 24

****** Page 29 ****** Appendix Important safety information CAUTIONS: • Use only the power adapter provided with this product. To obtain a replacement, visit our website at telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. • Use only the supplied rechargeable battery or replacement battery (model BT166342/BT266342). To order, visit our website at telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. • To prevent risk of fire or battery explosion, replace with the correct battery type. Dispose of used batteries according to the instructions. Especially about cordless telephones Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the handset by radio waves, so there is a possibility that your cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones. Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet which is not controlled by a wall switch. Calls cannot be made from the handset if the telephone base is unplugged, switched off or if the electrical power is interrupted. Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to TVs and VCRs. To minimize or prevent such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference. Rechargeable batteries: This product contains nickel-metal hydride rechargeable batteries. Exercise care in handling batteries in order not to create a short circuit with conductive material such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger. Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury. 25

****** Page 30 ****** Appendix Important safety information R BRC Ni-MH The RBRC@ Seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle nickel-metal hydride rechargeable batteries when taken out of service within the United States. These batteries may be taken to a participating local retailer of replacement batteries or recycling center. Or you may call 1-800-8-BATTERY@ for locations accepting spent Ni-MH batteries. RBRC@ and 1-800-8-BATTERY@ are registered trademarks of the Rechargeable Battery Recycling Corporation. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that: Pacemaker patients • Should keep wireless telephones at least six inches from the pacemaker. Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON. Should use the wireless telephone at the ear opposite the pacemaker. WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones. Especially about telephone answering systems Two-way recording: This unit does not sound warning beeps to inform the other party that the call is being recorded. To ensure that you are in compliance with any federal or state regulations regarding recording a telephone call, you should start the recording process and then inform the other party that you are recording the conversation. SAVE THESE INSTRUCTIONS 26

****** Page 31 ****** Appendix For C-UL compliance In compliance with the bilingual requirements for safety, caution, and warning markings of Canadian Federal and Provincial/ Territorial statutes and regulations, the French version of Important safety information is included. Mesures de sécurité importantes Ce symbole vous alertera d’informations importantes ou d’instructions d’entretien pouvant apparattre dans ce guide d’utilisation. Respectez touJours les mesures de sécurité et de sécurité de base lorsque vous utilisez ce produit, afin de réduire les risques de blessures, d’incendie, ou d’électrocution. Information relative ä la sécurité Veuillez lire et comprendre toutes les instructions de ce guide d’utilisation. Relectez toutes les inscriptions apparaissant sur le produit. Évitez d’utiliser le téléphone pendant un orage. II pourrait y avoir un faible risque d’électrocution. N’utilisez pas un téléphone proximité d’une fuite de gaz. Si vous soupconnez la présence d’une fuite de gaz, rapportez-la immédiatement, mais utilisez un téléphone situé dans un autre endroit que celui de la fuite de gaz. Si ce produit est un modéle sans fil, assurez-vous que le socle du téléphone se trouve également ä l’extérieur de cet endroit. N’utilisez pas ce produit prés de l’eau ou lorsque vous étes mouillés. Par exemple, ne l’utilisez pas dans des sous-sols humides ou sous la douche, ou prés d’une piscine, d’un bain, d’un évier de cuisine, ou d’une cuve de lavage. N’utilisez pas de liquides, ou de vaporisateurs aérosol de nettoyage. Si le produit entre en contact avec du liquide, débranchez immédiatement le fil téléphonique ou le cordon d’alimentation. Ne rebranchez pas le produit avant qu’il soit complétement sec. Installez cet appareil dans un endroit protégé oü personne ne peut trébucher sur les cordons d’alimentation ou la ligne téléphonique. Protégez les cäbles contre les dommages ou l’abrasion. Si le produit ne fonctionne pas correctement, consultez la section Dépannage (Troubleshooting) des pages 13-22 de ce guide d’utilisation. Si vous ne pouvez pas régler le probléme, ou si le produit est endommagé, consultez la section Garantie limitée (Limited warranty) des pages 34-36. N’ouvrez pas ce produit, sauf tel qu’indiqué dans le guide d’utilisation. L’ouverture du produit ou le remontage inadéquat pourrait vous exposer ä des tensions dangereuses ou autres dangers. Remplacez les piles uniquement tel que décrit dans votre guide d’utilisation (pages 6-7). N’incinérez pas et ne percez pas les piles elles contiennent des produits chimiques caustiques. L’adaptateur de courant est conqu pour étre orienté verticalement ou installé sur le plancher. Les broches ne sont pas conques pour se maintenir en place si la fiche est branchée dans une prise de courant au plafond, sous la table ou sous une armoire. 27

****** Page 32 ****** Appendix For C-UL compliance MISES EN GARDE: N’utilisez seulement l’adaptateur inclus avec ce produit. Pour obtenir une piéce de rechange, visitez notre site web au telephones.att.com ou composez le 1-800-222—3111. Au Canada, composez le 1-866-288-4268. N’utilisez que la pile de rechargeable incluse ou une pile de rechange (modéle BT166342/BT266342). Pour commander, visitez notre site Web telephones.att.com ou composez le 1-800-222-3111. Au Canada, le 1-866-288-4268. Afin de prévenir les risques d’incendie ou d’explosion de la pile, replacez la pile avec une pile du méme type. Jetez les piles épuisées en respectant les instructions. Spécifiquement en rapport avec les téléphones sans fil Confidentialité : Les mémes caractéristiques qui rendent les téléphones sans fil si pratiques créent également des restrictions. Les appels téléphoniques sont transmis entre le socle du téléphone et le combiné par le biais d’ondes radio, et il se peut que vos conversations téléphoniques soient interceptées par d’autres équipements de réception d’ondes radio au sein de la portée du téléphone sans fil. Pour cette raison, vous ne devez pas considérer les conversations sur un téléphone sans fil comme étant aussi confidentielles que celles d’un téléphone cordon. Alimentation électrique : La base de ce téléphone sans fil doit étre branchée une prise de courant électrique fonctionnelle. La prise électrique ne doit pas étre contrölée par un interrupteur mural. Les appels ne peuvent pas étre effectués ä partir du combiné si la base n’est pas branchée, si elle est hors fonction ou si le courant électrique est coupé. Interférences potentielles aux téléviseurs : Certains téléphones sans fil fonctionnent sur des fréquences pouvant causer des interférences aux téléviseurs et magnétoscopes. Pour réduire ou prévenir de tels parasites, ne pas déposer la base du téléphone sans fil ä proximité d’un téléviseur ou magnétoscope, ni directement sur celui-ci. Si votre téléviseur affiche des interférences, éloignez le téléphone sans fil de celui-ci afin de réduire les parasites. Piles rechargeables : Vous devez recycler ou Jeter les piles de maniére écologique. Ne pas Jeter dans les rebuts domestiques. Ne pas brüler ni percer les piles. Comme pour les autres piles du méme type, si elles sont brülées ou percées, des matiéres corrosives peuvent s’en échapper, ce qui risque de causer des brülures ou autres blessures corporelles. Piles rechargeables ä l’hydrure métallique de nickel : Jetez ces piles de maniére sécuritaire. N’incinérez pas et ne peercez pas les piles. Comme pour les autres piles du méme type, si elles sont brülées ou percées, des matiéres corrosives peuvent s’en échapper, ce qui risque de causer des brülures ou autres blessures corporelles. 28

****** Page 33 ****** Appendix For C-UL Ni-MH compliance Le sceau de l’organisme de recyclage RBRCMO sur les piles l’hydrure métallique de nickel signifie que le fabricant de cet appareil participe volontairement au programme industriel visant reprendre et recycler ce type de piles lorsqu’elles ne servent plus, au sein du territoire des États-Unis et du Canada. Vous devez apporter ces piles chez un détaillant participant ou le centre de recyclage le plus prés de chez vous. Ou vous pouvez composer le 1-800-8-BATTERYMD afin de connaTtre les endroits qui acceptent les piles l’hydrure métallique de nickel mortes. RBRCMO et 1-800-8-BATTERYMO sont des marques déposées de Rechargeable Battery Recycling Corporation. Mesures préventives pour les utilisateurs de stimulateurs cardiaques implantés dans l’organisme Stimulateurs cardiaques (ne s’applique qu’aux téléphones sans fil numériques) : L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États- unis, la firme WTR recommande aux médecins : Avis aux détenteurs de stimulateurs cardiaques Ils doivent tenir le téléphone sans fil une distance d’au moins six pouces du stimulateur cardiaque. Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en fonction. Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction opposée au stimulateur cardiaque. L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causé par les gens qui utilisent un téléphone sans fil proximité de ceux-ci. Spécifiquement en rapport avec les répondeurs téléphoniques Enregistrement deux voies : Cet appareil n’émet pas de bips d’avertissement qui permettent de prévenir l’autre partie que vous enregistrez la conversation. Pour assurer votre conformité aux réglements fédéraux ou provinciaux en rapport avec les enregistrements des conversations téléphoniques, vous devriez informer l’autre partie lorsque vous activez l’enregistrement. CONSERVEZ CES INSTRUCTIONS 29

****** Page 34 ****** Appendix FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your telephone service provider upon request. The plug and Jack used to connect this equipment to premises wiring and the telephone network must comply with the applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJII jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual. The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your telephone service provider. This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable the alarm equipment, consult your telephone service provider or a qualified installer. If this equipment is malfunctioning, it must be unplugged from the modular Jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty. If this equipment is causing harm to the telephone network, the telephone service provider may temporarily discontinue your telephone service. The telephone service provider is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone service provider is required to inform you of your right to file a complaint with the FCC. Your telephone service provider may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone service provider is required to notify you if such changes are planned. 30

****** Page 35 ****** Appendix FCC Part 68 and ACTA If this product is equipped with a corded or cordless handset, it is hearing aid compatible. If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please: Remain on the line and briefly explain the reason for the call before hanging up. Perform such activities in off-peak hours, such as early morning or late evening. Industry Canada Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation. The term “IC:” before the certification/registration number only signifies that the Industry Canada technical specifications were met. The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five. This product meets the applicable Industry Canada technical specifications. 31

****** Page 36 ****** Appendix FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the supplied AT&T belt clip. This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 For body worn operation, this handset has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of (Omm) from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. 32

****** Page 37 ****** Appendix California Energy Commission battery charging testing instructions This telephone is set up to comply with the energy-conserving standards right out of the box. These instructions are intended for California Energy Commission (CEC) compliance testing only. When the CEC battery charging testing mode is activated, all telephone functions on the cordless handsets, except battery charging, will be disabled. When first purchased and properly installed for charging (see Battery installation and charging on pages 6-7), put the handset in the handset charger to charge. The CEC battery charging testing mode is activated while charging. If you have registered the handset to the TL86109 base, below are the testing instructions. To activate the CEC battery charging testing mode: 1. 2. 3. When the phone is not in use, press and hold FLASH on the telephone base for about 4 seconds until it shows Deregister all handsets? Then, release the button. Press the YES softkey to continue. You hear a confirmation tone from the telephone base. The telephone base displays PLEASE WAIT… All system handsets show Out of range OR no power at base for a few seconds, and then you hear a confirmation tone from the handset. When the phone successfully enters the CEC battery charging testing mode, all handsets show Press [HOLD] on base for 4 sec, then press on handset When the phone fails to enter this mode, repeat all the steps mentioned above. To deactivate the CEC battery charging testing mode: 1. Unplug the telephone base power adapter from the power outlet, then plug it back in. The telephone base is powered up as normal. 2. Register your handsets back to the telephone base. See page 11 for handset registration instructions. BC 33

****** Page 38 ****** Appendix Limited warranty The AT&T brand is used under license – any repair, replacement or warranty service, and all questions about this product should be directed to: In the United States of America, call I (800) 222-3111 or visit telephones.att.com; in Canada, call 1 (866) 288-4268. What does this limited warranty cover? 1. The manufacturer of this AT&T-branded product warrants to the holder of a valid proof of purchase (“CONSUMER” or “you”) that the product and all accessories provided in the sales package (“PRODUCT”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the PRODUCT operating instructions. This limited warranty extends only to the CONSUMER for products purchased and used in the United States of America and Canada. What will be done if the PRODUCT is not free from defects in materials 2. and workmanship during the limited warranty period (“materially defective PRODUCT”)? During the limited warranty period, the manufacturer’s authorized service representative repairs or replaces at the manufacturer’s option, without charge, a materially defective PRODUCT. If the manufacturer repairs the PRODUCT, they may use new or refurbished replacement parts. If the manufacturer chooses to replace the PRODUCT, they may replace it with a new or refurbished PRODUCT of the same or similar design. The manufacturer retains the defective parts, modules, or equipment. Repair or replacement of the PRODUCT, at the manufacturer’s option, is your exclusive remedy. The manufacturer returns the repaired or replacement products to you in working condition. You should expect the repair or replacement to take approximately 30 days. How long is the limited warranty period? 3. The limited warranty period for the PRODUCT extends for ONE (1) YEAR from the date of purchase. If the manufacturer repairs or replaces a materially defective PRODUCT under the terms of this limited warranty, this limited warranty also applies to repaired or replacement PRODUCT for a period of either (a) 90 days from the date the repaired or replacement PRODUCT is shipped to you or (b) the time remaining on the original one-year limited warranty; whichever is longer. 34

****** Page 39 ****** Appendix Limited warranty 4. What is not covered by this limited warranty? This limited warranty does not cover: PRODUCT that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water, or other liquid intrusion; or PRODUCT that has been damaged due to repair, alteration, or modification by anyone other than an authorized service representative of the manufacturer; or PRODUCT to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or PRODUCT to the extent that the problem is caused by use with non-AT&T accessories; or PRODUCT whose warranty/quality stickers, PRODUCT serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or PRODUCT purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to products used for rental purposes); or PRODUCT returned without a valid proof of purchase (see item 6); or Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the unit. 5. How do you get warranty service? To obtain warranty service in the United States of America, visit telephones.att.com or call 1 (800) 222-3111; in Canada, please dial I (866) 288-4268. NOTE: Before calling for service, please review the user’s manual. A check of the PRODUCT’s controls and features might save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the PRODUCT(s) to the service location. The manufacturer will return repaired or replaced PRODUCT under this limited warranty. Transportation, delivery or handling charges are prepaid. The manufacturer assumes no risk for damage or loss of the PRODUCT in transit. If the PRODUCT failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, the manufacturer notifies you and requests that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of products that are not covered by this limited warranty. 35

****** Page 40 ****** Appendix Limited warranty 6. What must you return with the PRODUCT to get warranty service? You must: a. b. c. Return the entire original package and contents including the PRODUCT to the service location along with a description of the malfunction or difficulty; and Include “valid proof of purchase” (sales receipt) identifying the PRODUCT purchased (PRODUCT model) and the date of purchase or receipt; and Provide your name, complete and correct mailing address, and telephone number. 7. Other limitations This warranty is the complete and exclusive agreement between you and the manufacturer of this AT&T branded PRODUCT. It supersedes all other written or oral communications related to this PRODUCT. The manufacturer provides no other warranties for this PRODUCT. The warranty exclusively describes all of the manufacturer’s responsibilities regarding the PRODUCT. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you might also have other rights that vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the PRODUCT is fit for ordinary use) are limited to one year from date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation might not apply to you. In no event shall the manufacturer be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the PRODUCT or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this PRODUCT. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion might not apply to you. Please retain your original sales receipt as proof of purchase. 36

****** Page 41 ****** Appendix Technical specifications 1921.536MHz 1928.448MHz ooc 500C RF frequency band Channels Operating temperature Handset voltage Charger voltage (DC adapter output) Replacement battery Operating times* 5 320F — 1220F 2.4 — 3.2 VDC 6VDC @ 400mA 2.4V 750mAH Talk time (handset): up to seven hours Talk time (speakerphone): up to five hours Standby: up to seven days * Operating times vary depending on your actual use and the age of the battery. DECT 6.0 digital technology The AT&T DECT 6.0 products offer unsurpassed range performance and sound clarity. This is achieved through a unique antenna design and advances in noise-filtering technology. An independent laboratory has confirmed that AT&T DECT 6.0 products perform up to 45% better in range competitions. Now, calls can be taken in the basement, backyard and garage with exceptional sound quality. 37

****** Page 42 ****** Appendix Technical specifications Telephone operating range This cordless telephone operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base can communicate over a certain distance — which can vary with the locations of the telephone base and handset, the weather, and the construction of your home or office. Extended range and clarity This telephone base comes with an antenna which gives much better clarity and covers a longer range than before. 38

****** Page 43 ****** at&t telephones.att.com The Bluetooth’ word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by Advanced American Telephones and its parent, VTech Holdings Limited, is under license. VTech Holdings Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. 0 2010-2014 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219. RBRC@ and 1-800-8-BATTERY@ are registered trademarks of the Rechargeable Battery Recycling Corporation. Printed in China. Issue 6.1 AT&T 10/14.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

AT&T TL86109 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.