PDF Content Summary:
****** Page 1 ****** Quick start guide CL82115/CL82215/CL82315/CL82415/CL82465/CL82515 This quick start guide provides you with basic instructions only. For more complete instructions, refer to your Abridged user’s manual provided in the package, or see the online Complete user’s manual at telephones.att.com/manuals. Quick reference guide – handset CHARGE light On when the handset is charging in the telephone base or charger. VCID/VOLUME • Press ‘CID to show caller ID log when the handset is not in use. Press to scroll down while in menus. Press to decrease the listening volume when on a call. REDIAL/PAUSE Press repeatedly to view the last ten numbers dialed. While entering numbers, ress and hold to insert a Quick reference guide – telephone base Message counter Shows the number of messages or other answering system information. X/DELETE Press to delete the message currently playing. Press twice to delete all old messages when the Telephone base installation Plug one end of the telephone line cord into a telephone jack or a DSL filter. If you have DSL high- speed Internet service, a DSL filter (not included) is required. Route the telephone line cord through this slot. Raise the antenna. Plug the other end of the Plug the large end of the telephone base power adapter into a power outlet not controlled by a wall switch. Route the power adapter cord through this slot. Plug the small end of the telephone base power adapter into the power adapter jack on the back of the telephone base. Charger installation Plug the power adapter into a power outlet not controlled by a wall switch. 11 CHARGE REDIAL PAUSE MENU j CANCEL ADIR/VOLUME Press ADIR to show directory entries when the handset is not in use. Press to scroll up while in menus. Press to increase the listening volume when on a call. MENU/SELECT When the handset is not in use, press to show the menu. While in the menu, press to select an item or save an entry or setting. ‘OFF/CANCEL During a call, press to hang up. While in a menu, press to cancel an operation, back up to the previous menu, or exit the menu display; or ress and hold this button to exit toi e mode. QUIET# (pound key) Press and hold to enter the QUIET mode setting screen, or to deactivate QUIET mode. During an outside call, intercom call, message or announcement playback, press to change the audio quality to best suit your hearing. MUTE/DELETE During a call, press to mute the microphone. Press to delete digit or character. IN USE indicator On when the handset is in use, or when the answering system is answering an incoming call. Flashes when another telephone is in use on the same line. IN IBSE «/REPEAT Press to repeat a message. Press twice to play the previous message. (b/ANS ON/OFF Press to turn the built-in answering system on or off. Initial settings Caner ‘D 88 88 telephone line cord into the telephonejack on the back of the telephone base. ia ing pause. kPHONE/FLASH Press to make or answer a call. Press and hold to set or dial your voicemail number. Press to switch to tone dialing temporarily during a call if you have pulse service. While entering names, press to change the next letter to upper or lower case. O/SPEAKER Press to make or answer a call using the speakerphone. Handset side view phone is not in use. »/SKIP Press to skip a message. >/MPLAY/STOP Press to start or stop message playback. C FIND HS While the phone is idle, press to page all handsets. VVOLUME and AVOLUME During message playback, press to adjust the listening volume. While in idle mode, press to adjust the base ringer volume. Caution: Use only the power adapter(s) provided with this product. To obtain a replacement, visit our website at telephones.att.com or call 1 (800) 222-3111 In Canada, 1 (866) 288-4268 Battery installation Install the battery, as shown below. Charge your handset(s) before initial use. The battery is fully charged after ten hours of continuous charging. Step 1 Plug the battery connector securely into the socket inside the handset battery compartment. Insert the supplied battery with the label THIS SIDE UP facing up, as indicated. Step 2 Align the cover flat against the battery compartment, then slide it upwards until it clicks into place. CHARGE light Step 3 MUTE DELETE PUSH TO TALK Press to initiate a one-to-one or one-to-group broadcast. Press and hold to broadcast to a group of system handsets. We recommend you program your telephone system before LISe. The following are a few examples of common features to set before using the telephone. Refer to the Handset settings and Answering system settings in the Abridged user’s manual or the online Complete user’s manual for detailed instructions on setting all telephone features. Set date/time Set the date/time before using the answering system. 1. MENU -> V or A -> Set date/time -> SELECT. 2. Enter the month, day and year using the dialing keys -> SELECT. 3. Enter the hour and minute using the dialing keys. 4. V or A to choose AM or PM -> SELECT. Basic answering system setup via voice guide Your can follow the voice guide to record your own announcement, set the number of rings, and set the message alert tone. Using a cordless handset: 1. MENU v or A Answering sys SELECT. 2. v or A Voice guide SELECT. 3. Set up your answering system by inputting the designated numbers, as instructed. 88 Charge the handset by placing it face forward in the telephone base or charger. The CHARGE light on the handset is on during charging. Use only the supplied rechargeable battery or replacement battery (model B T 183342/ BT283342).
****** Page 2 ****** Initial settings (continued) Record your own announcement Your outgoing announcement plays when calls are answered by the answering system. You can use the preset announcement to answer calls, or replace it with your own recorded announcement. 1. MENU -> V or A -> Answering sys -> SELECT. 2. SELECT to select Announcement. 3. SELECT to select Record annc. 4. Facing the handset, record your announcement and press 5 to end recording. Number of rings You can set the answering system to answer an incoming call after two, three, four, five or six rings, or toll saver. If you choose toll saver, the answering system answers a call after two rings if you have new messages, or after four rings when there are no new messages. This enables you to check for new messages and avoid paying unnecessary long distance charges if you are calling from out of your local area. If you want the built-in answering system instead of the voicemail to answer a call, you should set the answering system to answer a call at least two rings before the voicemail is set to answer. Contact your telephone service provider for information on your voicemail settings. 1. MENU -> V or A -> Answering sys -> SELECT. 2. V or A -> Ans sys setup -> SELECT. 3. V or A -> # of rings -> SELECT. 4. V or A to choose among 2, 3, 4, 5, 6 or Toll saver -> SELECT. Ringer volume You can set the ringer volume level to one of the six levels or turn the ringer off. 1. MENU V or A Ringers SELECT. 2. SELECT to select Ringer volume. 3. V or A to choose the desired level -> SELECT. Reset language to English If you have accidentally changed the screen display language and want to switch it back to English, follow the steps mentioned below. MENU in idle mode -> enter 364#. Telephone operation Caller ID This product supports caller ID services offered by most telephone service providers. The telephone stores caller ID information of the last 50 incoming calls in the telephone base. This information is common to all devices. Missed call indicator When a handset is in idle mode and has new or missed calls, its screen shows XX Missed calls. You can erase the missed call indicator either by reviewing the call log one by one, or by pressing and holding CANCEL in idle mode. Review and dial a number in the call log 1. CID in idle mode -> V or A to scroll through the list. 2. k PHONE or O/SPEAKER to call when the desired entry is displayed. Caller ID announce When this feature is on and you have an incoming call, the handset speaks “Call from…” and the name of the caller based on the directory or caller ID information. You can turn this feature off at the base or on each individual handset, or both. 1. MENU V or A Settings SELECT. 2. V or A Caller ID annc SELECT. 3. V or A to choose Set all On/Off, Local handset or Base -> SELECT. 4. V or A to choose On or Off -> SELECT. Call block If you have subcribed to caller ID service, you can use the call block feature to reject certain calls automatically. The call block list can store up to 20 entries. This feature is only available on the cordless handset. Operation Adding a call block entry Blocking calls without number Directory Steps 1. MENU V or A Call block SELECT. 2. SELECT to select Block list. 3. V or A -> Add new entry -> SELECT. 4.Enter a telephone number up to 30 digits -> SELECT. 5. Enter a name up to 15 characters -> SELECT. 1. MENU V or A Call block SELECT. 2. V or A Calls w/o num SELECT. 3. V or A to choose Not block or Block. Answering system About answering system and voicemail Your telephone has separate indicators for two different types of voice messages: those left on the built-in answering system and those left at your telephone service provider’s voicemail. To listen to messages recorded on the built-in answering system, refer to the Message playback section; to listen to voicemail, contact your telephone service provider for more information. Turn answering system on/off The answering system must be turned on to answer and record messages. 1. MENU. 2. V or A -> Answering sys -> SELECT. 3. V or A Answer ON/OFF SELECT. 4. V or A to choose On or Off -> SELECT. When the answering system is on, the handset shows ANS ON. Message alert tone When this feature is on, and there is at least one new message, the telephone base beeps every 10 seconds. 1. MENU -> V or A -> Answering sys -> SELECT. 2. V or A -> Ans sys setup -> SELECT. 3. V or A -> Msg alert tone -> SELECT. 4. V or A to choose On or Off -> SELECT. Call screening Use this feature to choose whether incoming messages can be heard over at the telephone base when they are being recorded. If you turn call screening on, you hear the incoming message at the telephone base. While monitoring an incoming message, you can answer the call by pressing k PHONE on the handset. 1. MENU -> V or A -> Answering sys -> SELECT. 2. V or A -> Ans sys setup -> SELECT. 3. SELECT to select Call screening. 4. V or A to choose On or Off -> SELECT. Message playback Using the telephone base: Press >/I/PLAY when the telephone base is in idle mode. Using a cordless handset: Press MENU twice when the handset is in idle mode. Operation Making a call On-hook dialing (predialing) Answering a call Ending a call Handset speakerphone Redial Volume control Call waiting (Requires subscription from telephone service provider) Steps Press kPHONE or O/SPEAKER Enter the telephone number. Enter the telephone number -> Press kPHONE or O/SPEAKER to call. Press kPHONE or O/SPEAKER, or press any dialing keys (0-9, TONE* or Press ‘)OFF or return the handset to the telephone base or charger. During a call, press O/SPEAKER to switch between handsfree speakerphone and normal handset use. Press REDIAL repeatedly to select the desired entry k PHONE or O/SPEAKER to call. Press V VOLUME to decrease or press A VOLUME to increase the listening volume during a call. Press FLASH to put current call on hold and to take the new call; press again to switch back and forth between calls. The directory can store up to 50 entries, which are shared by all system handsets. Options during playback Feature Adjust playback volume Stop playback Skip to the next message Repeat the message Play the previous message Delete the message On the telephone base Press ‘VOLUME or AVOLUME Press >/./STOP Press »/SKIP Press «/REPEAT Press «/REPEAT twice Press X/DELETE On a handset Press ‘VOLUME or AVOLUME Press 5 Press 6 Press 4 Press 4 twice Press DELETE Operation Adding an entry Searching/ dialing an entry Steps 1. MENU. 2. V or A Directory SELECT. 3. V or A Add contact SELECT. 4. Enter a telephone number up to 30 digits -> SELECT. 5. Enter a name up to 15 characters -> SELECT. 1. DIR in idle mode. 2. Press V or A to browse through the directory, or press the dialing keys (0-9) to start a name search. 3. Press kPHONE or O/SPEAKER on a handset to call. For more detailed instructions, please refer to the Abridged user’s manual provided in your package, or for a full set of installation and operation instructions, refer to the online CL82115/CL82215/CL82315/CL82415/CL82465/ CL82515 DECT 6.0 cordless telephone/answering system with caller ID/call waiting Complete user’s manual at telephones.att.com/manuals. For customer service or product information, visit our website at telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 0 2015-2017 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219. Printed in China. Issue 2.0 AT&T 03/17.
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL