Click here to download AT&T 983 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** at&t Quick start guide 983 Two-Line speakerphone LINE 0 e Line FL.e* w:uu 0 5)

****** Page 2 ****** Battery installation Before using the telephone, you should install four AA alkaline batteries (purchased separately). You can use the telephone without batteries to dial and receive calls. However, the line lights and the automatic redial feature will not work, and the speakerphone and optional headset may not work properly in all conditions. To use the speakerphone without batteries, you must press and hold OSPEAKER for one second. O NOTES: • If you do not install batteries, you will hear a low battery warning tone every time you lift the handset or press OSPEAKER. • Use disposable alkaline batteries only Do not use rechargeable batteries. CAUTION: Always unplug the line cord, before installing new batteries. 1. Press the tab as shown and flip into the down- ward position. 2. Push the tab as shown and lift to remove the battery cover. Insert four new AA alkaline batteries (purchased separately) following the polarity markings in the battery compartment. 3. Replace the battery cover. The following symptoms indicate that the batteries in your telephone are low and need to be replaced, even if there is no low battery warning yet: • The automatic redial feature does not work or is not working properly, or • HEADSET cannot be used to make or answer calls. If you experience either of these symptoms, try replacing the batteries following the instructions above.

****** Page 3 ****** Tabletop installation After installing the batteries, if you wish to use the telephone on a tabletop, flip the wall mounting bracket upward. A single two-line wall jack If there is a single two-line wall jack, use only the black (4-connector) line cord. Plug one end into the jack labeled LI or LI/L2 on the back of the telephone base. Plug the other end into the wall jack. Make sure the line cord is plugged firmly into the telephone base and the wall jack. Line I + Line 2 aut 00 1. Connect the line cord to the tele- phone base and wall jack. 2. Plug one end of the coiled handset cord into the handset. Plug the other end into the jack on the left side of the telephone base. NOTE: This product is designed to operate optimally with two telephone lines. If you choose to install only one telephone line; the telephone will continue to operate normally as long as the unused line is not selected. If you experience diffi- culty, make sure you have pressed the correct LINE key.

****** Page 4 ****** Tabletop installation Two one-line wall jacks If there are two one-line wall jacks, use both long line cords. Plug one end of the clear line cord into the jack labeled Ll or Ll/L2 on the back of the telephone base. Then, plug the other end into the wall jack for Line 1. Plug one end of the black line cord into the jack labeled L2 or DATA on the back of the telephone base. Then, plug the other end into the wall jack for Line 2. Make sure the line cords are plugged firmly into the telephone base and the wall jack. Line 1 Line 2 00 0 Connect the line cords to the 1. telephone base and wall jacks. Plug one end of the coiled handset 2. cord into the handset. Plug the other end into the jack on the left side of the telephone base. 3. To determine which line is in use, press LINE 1 and call one of the telephone numbers. If there is a busy signal, Line 1 is the number you called. If Line 2 rings, it is the number you called. NOTE: This product is designed to operate optimally with two telephone lines. If you choose to install only one telephone line, the telephone will continue to operate normally as long as the unused line is not selected. If you experience diffi- culty, make sure you have pressed the correct LINE key.

****** Page 5 ****** Quick reference guide One-touch ke s Press to dial the number stored. LINE 1, LINE 2 Press, then lift handset to make or answer a call on line 1 or 2 CONFERENCE Press to enter three-way conference call. (AUTO) REDIAL Lift the handset. Press to dial the last number dialed. FLASH During a call, press to receive an incoming call if call waiting is activated. at&t L ine LOWER Press LOWER, then the desired one- touch key to dial the number stored in lower locations. HOLD Press to place call on hold. PROGRAM Press to program memory dial numbers. PAUSE Press to insert a dialing pause. $VOLUME FLASH PAUSE ooo ooo MIC MIJTE During a call, press A or to adjust listening volume. HEADSET Press to activate headset. MUTE Press to silence the micro- phone. Press again to resume telephone conver- sation. SPEAKER Press to turn the speaker- phone on or off (begin or end a call). NOTE: For more information, please refer to the user’s manual.

****** Page 6 ****** at&t wwwetelephones.att.com 0 2008 Advanced American Telephones. All rights reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a AT&T Intellectual Property licensed to Advanced American Telephones. Printed in China. Issue 4 AT&T 04/08.

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



AT&T 983 (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.