PDF Content Summary:
****** Page 1 ****** ATEN CAMLIVE HDMI to USB-C UVC Video Capture User Manual aten.com
****** Page 2 ****** CAMLIVE User Manual EMC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. RoHS This product is RoHS compliant.
****** Page 3 ****** CAMLIVE User Manual User Information Online Registration Be sure to register your product at our online support center: International eservice.aten.com Telephone Support For telephone support, call this number: International China Japan Korea North America User Notice 886-2-8692-6959 86-400-810-0-810 81-3-5615-5811 82-2-467-6789 1-888-999-ATEN ext 4988 All information, documentation, and specifications contained in this manual are subject to change without prior notification by the manufacturer. The manufacturer makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the manufacturer’s software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not the manufacturer i its distributor, or its dealer), assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any defect in the software. The manufacturer of this system is not responsible for any radio and/or TV interference caused by unauthorized modifications to this device. It is the responsibility of the user to correct such interference. The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE.
****** Page 4 ****** CAMLIVE User Manual Package Contents 1 CAMLIVE HDMI to USB-C UVC Video Capture 1 USB-C to USB-A Adapter* 1 User Instructions *When using the adapter, if you are only detecting MJPG video, please disconnect the USB-C head from the adapter, flip the USB-C head around and reconnect it to the adapter. Please refer to Using USB-A Adapter on page 14 for more details. Note: Make sure that all of the components are present and in good order. If anything is missing or was damaged in shipping, contact your dealer.
****** Page 5 ****** CAMLIVE User Manual Table of Contents .. . .viii 1. 2. 3. 4. EMC Information RoHS. User Information … .. Online Registration Telephone Support User Notice . Package Contents About this Manual Conventions Product Information.. Introduction Overview Features Planning the Installation Requirements . Supported Operating System and Requirements Components . Hardware Setup Connecting the CAMLIVE Unit . Software Android Smartphone Livestream I Record Setup Livestream / Record Platform . Discovering CAMLIVE on your System.. Video and Audio Setup .. Discovering CAMLIVE on your Android Device . Using USB-A Adapter .. The Firmware Upgrade Utility Overview Downloading the Firmware Upgrade Package Preparation . Starting the Upgrade Upgrading the CAMLIVE to Support Android Smartphone Upgrading the CAMLIVE to Support PC Appendix Safety Instructions. ii ii vii .. viii 1 2 2 .2 .3 .3 .5 .6 .6 6 .9 .13 . 14 17 .18 19 19 .22 25
****** Page 6 ****** CAMLIVE User Manual General Technical Support International North America Specifications Limited Warranty vi 25 27 27 27 28 30
****** Page 7 ****** CAMLIVE User Manual About this Manual This user manual is provided to help you get the most from the CAMLIVE unit. It covers all aspects of installation, configuration, and operation. An overview of the information found in the manual is provided below. Chapter 1, Introduction introduces you to the HDMI to USB-C UVC Video Capture. Its purpose, features, installation considerations, and panel components are presented and described. Chapter 2, Hardware Setup describes the steps that are necessary to quickly and safely set up your installation Chapter 3, Livestream I Record Setup explains how to find CAMLIVE on your system and presents how to setup video and audio source using an example live-stream/record software/platform. Chapter 4, The Firmware Upgrade Utility explains how to download the CAMLIVEs firmware and upgrade the device using the utility. Appendix provides a list of safety instructions and precautions, contact information for ATEN technical support, product specifications, and other technical information Note: Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit or any connected devices. ATEN regularly updates its product documentation for new features and fixes. For an up-to-date CAMLIVE documentation, visit aten.com/global/en/ vii
****** Page 8 ****** CAMLIVE User Manual Conventions This manual uses the following conventions: Monospaced Indicates text that you should key in. Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them: [Ctrl+Alt]. Numbered lists represent procedures with sequential steps. Bullet lists provide information, but do not involve sequential steps. Indicates selecting the option (on a menu or dialog box, for example), that comes next. For example, Start -+ Run means to open the Stan menu, and then select Run. Indicates critical information. Product Information For information about all ATEN products and how they can help you connect without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller. Visit ATEN on the Web for a list of locations and telephone numbers: International North America viii aten.com aten-usa.com
****** Page 9 ****** Chapter 1 Introduction Overview “CAMLIVE” is an HDMI UVC Video Capture device that sends unencrypted HDMI video to your USB-C or Thunderbolt 3 laptop (or USB-A with the included adapter), or an UVC capture ready Android smartphone. It’s compliant with latest USB 3.1 Type-C specification. CAMLIVE is designed to Plug & Play. Its built-in UVC and UAC standard support allows system operation without installing drivers and, at the same time, delivers eye-popping, high-quality video on Windows and Mac systems at 1080/ 60fps. By sending captured RAW data, you can enjoy video editing or live streaming with various popular third-party video-editing software/platforms – Open Broadcaster Software (OBS), Xsplit, Twitch, YouTube, Facebook, Camerafi, to name a few. Having a slim and aesthetic design, CAMLIVE provides you with an enjoyable, high-quality live streaming/video editing experience with style whether at work or on the go.
****** Page 10 ****** CAMLIVE User Manual Features Captures unencrypted HDMI video signal such as camcorder or DSLR up to 1080P @ Supports live video streaming, webcasting and video conferencing Compatible with popular streaming software, such as OBS, Xsplit, YouTube, Facebook and Twitch Plug & Play – Supports UVC/UAC vl .1 Compatible with USB3.1 Genl Type-C standard Works with all major operating systems: Windows@ and OS X@ Works with UVC capture ready Android smartphone *CAMLIVE cannot display or capture HDCP protected content Planning the Installation Requirements Prepare the following before installing the CAMLIVE unit: • 1 HDMI and/or VGA source device • 1 Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable 2
****** Page 11 ****** Chapter 1. Introduction Supported Operating System and Requirements Operating System Windows 7 with Win7 driver installed Windows 10 or later OS X 10.13 or later Minimum Hardware Requirement CPU: Intel@ i3 Dual Core 2.8Ghz or higher RAM: 4GB or more One USB-C Interface or USB-A Interface Android 5.0.1 or later with UVC support Android smartphone with UVC and USB-C Interface Note: For Windows 7 users, please download and install the Win7_driver from on our website. To download the driver, see Downloading the Firmware Upgrade Package, page 17. Components No. 1 2 m z Component HDMI Port USB-C Host Connector Description Connects to an HDMI input. Connects to the host for video capture or firmware upgrade. 3
****** Page 12 ****** CAMLIVE User Manual This Page Intentionally Left Blank 4
****** Page 13 ****** Chapter 2 Hardware Setup Please review the safety information regarding the placement of this device in Safety Instructions, page 25. Connecting the CAMLIVE Unit Follow the steps below to connect the CAMLIVE to an HDMI source and the host. or HDMI (unencrypted) CAMLIVE 1. 2. 3. Power on your host (e.g. laptop or Android smartphone). Connect the USB-C Host Connector to the host. If your laptop only has a USB-A interface, connect the (included) USB-C to USB-A adapter* between the host and the USB-C Host connector. Connect your HDMI source device to the CAMLIVEs HDMI port.** *When using the adapter, if you are only detecting MJPG video, please disconnect the USB-C head from the adapter, flip the USB-C head around and reconnect it to the adapter. Please refer to Using IJSB-A Adapter on page 14 for more details. **UC3020 cannot display or capture HDCP protected content 5
****** Page 14 ****** CAMLIVE User Manual Software To enable CAMLIVE, please download and install a suitable video recording or live streaming software for your requirement. Below lists some examples of supported video recording / live streaming software for PC. All trademarks are property of their respective owners. OBS: obsproiect.com Xsplit: xsplit.com youtube.com facebook.com Android Smartphone Below is an example of supported vide recording / live streaming for Android smartphone. All trademarks are property of their respective owners. play.google.com/store/apps/details?id=com.vaultmicro.camerafi&hl=en A general reference of how to go about using CAMLIVE is described in the next chapter. 6
****** Page 15 ****** Chapter 3 Livestream I Record Setup Livestream I Record Platform Below lists a few of the available live-streaming or recording software/platforms: OBS: obsproject.com Xsplit: xsplit.com youtube.com facebook.com All trademarks are property of their respective owners. Discovering CAMLIVE on your System CAMLIVE is a plug-and-play device, please make sure your system is able to discover it. After connecting CAMLIVE as shown in Connecting the CAMLIVE Unit on page 5, refer to the MacOS example below on how your system may discover CAMLIVE: 1. On the desktop, click to select “Go” followed by “Utilities” sect oxt to osc OXA OXU OXG
****** Page 16 ****** CAMLIVE User Manual 2. 3. On the “Utilities” window, double-click ‘System Information” to bring up the system window. View GO S hot WirdNv “-klp LRi’Äies Numbers Ph’O•t0 Ptw•man Pre.ie”‘ Croati.•e Cloud auk;tdim•:• •e “USB” System Go to the USB page by clicking saws.ÅTÅ pr under “Hardware”. 0.0 r•as.. Mac 1.5 HO magic Disa teet Shot 18-01-0….a,42AM S net snot 4. Under “USB 3.0 Bus”, you should see an “HDMI to l.J3 capture”. This indicates that your system has successfully discovered CAMLIVE.
****** Page 17 ****** Chapter 3. Livestream / Record Setup MacBook Pro .1 USB Device Tree v USB 3.0 Bus HDMI to 03 capture V Hardware ATA Audio Bluetooth Camera Card Reader Diagnostics Disc Burning Ethernet Cards Fibre Channel FireWire Graphics/Displays Hardware RAID Memory NVMExpress PCl Parallel Power Printers SAS SATA/SATA Express SPI Storage Thunderbolt iBridge iBridge USB 3.1 Bus USB 3.1 Bus USB 3.0 Bus: Host Controller Driver: PCl Device 10: PCl Revision D: PCl Vendor ‘D: AppleUSBXHClSPTLP Ox9d2f ox0021 ox8086 HDMI to U3 capture: Product ID: Vendor ID: Version; Serial Number: Speed: Manufacturer: Location ID: Current Available (mA): Current Required (mA): Ox701f Oxle4e (Etron Technology, Inc.) 1.00 20000130041415 Up to 480 Mb/sec Video Grabber ox14300000 / 1 500 150 Extra Operating Current (mA): O Go to the next section for an example of how to setup both video and audio for live-streaming and recording using CAMLIVE. Video and Audio Setup After your system discovers CAMLIVE, choose your livestream/record platform. You will need to setup the video and audio source coming from CAMLIVE. Follow the steps below to setup your video and audio sources (separately). Note: OBS software is the example used in the setup steps below. O Dritm Cr«tiv• Files 3700T-UEB.00kPt— O Disc Mi#ian PfX’t•o Plt To select an installation folder, click Browse, or click Next to continue. Device Upgrade Select Installation Folder x The installer will install Device Upgrade to the following folder. To install in this folder. click ‘ ‘Next”. To install to a different folder* nter it below or “Browse”. Folder: Disk cost… Install Smattphne Suppott for yourself, or for anyone who this connpLiET: @Everyone C) Just me Next >
****** Page 29 ****** 4. 5. Chapter 4. The Firmware Upgrade Utility A confirmation screen appears, click Next to perform the upgrade Device Upgrade Confirm Installation The installer is ready to install Device Upgrade on your computer. Cl’ck “Next’ • to start the installation. Cancel After the upgrade has completed, click Close to close the Firmware Upgrade Utility. 21
****** Page 30 ****** CAMLIVE User Manual Upgrading the CAMLIVE to Support PC To upgrade the CAMLIVE to support PC video capture: 1. Extract and open the downloaded firmware upgrade package file, right click on the Setup icon, and select Run as administrator as shown in the picture below. 9’wre View asy •cess • Cam Com Dekte rte to • _J uc.nn Deeice_lJpyü X o Open Select see•ct D Seych Device_ Oat’ Type OneDrive 30 Ace 9′ Run 7.z,p Shye ken wa:h to Sexd tc Cree:’ 2. The Firmware Upgrade Utility welcome screen appears, and select Next. Smattphone Support Welcome to the Smartphone Support Setup Wizard The installer will guide you through the steps required to ‘nstall Smartphone Support on your computer. WARNING: This computer program i: protected by copyright law and international treaties X Unauthorized duplication or dl$tnbution of this program, or any portion of it, may result in severe civil or criminal penalties, and will be prosecuted to the maximum extent possible under the law. Next > 22
****** Page 31 ****** Chapter 4. The Firmware Upgrade Utility To select an installation folder, click Browse, or click Next to continue. 3. 4. 5. Smartphone Support Select Installation Folder X The installer Will install Srnartphone Support to the following folder. To install in this folder, click “Next”. To install to a different folder, nter it below or click “Browse”. Folder: Oi$k Cost… Install Smartphone Support fu yourself or for anyone who uses this computer: @Everyone C) Just Next) A confirmation screen appears, click Next to perform the upgrade. Smartphone Support Confirm Installation The installer is ready to install Snwtphone Support on your cmputer, Click ‘ ‘Next” to start the installation. x Next > After the upgrade has completed, click Close to close the Firmware Upgrade Utility. Note: For Windows 7 users, please download and install the Win7 driver from on our website after the upgrade is successful. See Downloading the Firmware Upgrade Package, page 17. 23
****** Page 32 ****** CAMLIVE User Manual This Page Intentionally Left Blank 24
****** Page 33 ****** Appendix Safety Instructions General • This product is for indoor use only. Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result. Do not use the device near water. Do not place the device near, or over, radiators or heat registers. The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered. The device should never be placed on a soft surface (bed, sofa, rug etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided. Never spill liquid of any kind on the device. Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. The device is designed for IT power distribution systems with 230V phase- to-phase voltage. To prevent damage to your installation it is important that all devices are properly grounded. The device is equipped with a 3-wire grounding type plug. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not attempt to defeat the purpose of the grounding-type plug. Always follow your local/national wiring codes. Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over. If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the 25
****** Page 34 ****** CAMLIVE User Manual • • 26 extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS). Position system cables and power cables carefully; Be sure that nothing rests on any cables. Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock. Do not attempt to service the device yourself. Refer all servicing to qualified service personnel. If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair. The power cord or plug has become damaged or frayed. Liquid has been spilled into the device. The device has been exposed to rain or water. The device has been dropped, or the cabinet has been damaged. The device exhibits a distinct change in performance, indicating a need for service. The device does not operate normally when the operating instructions are followed. Only adjust those controls that are covered in the operating instructions. Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.
****** Page 35 ****** Appendix Technical Support International • For online technical support including troubleshooting, documentation, and software updates: support.aten.com • For telephone support, see Telephone Suppott, page iii: North America Email Support Online Technical Troubleshooting Support Documentation Software Updates Telephone Support firstname.lastname@example.org aten-usa.com/support 1-888-999-ATEN ext 4988 When you contact us, please have the following information ready beforehand: Product model number, serial number, and date of purchase Your computer configuration, including operating system, revision level, expansion cards, and software Any error messages displayed at the time the error occurred The sequence of operations that led up to the error Any other information you feel may be of help 27
****** Page 36 ****** CAMLIVE User Manual Specifications Function Connectors Video In USB Port Video Input Compliance Video Resolution Color Space Audio Sampling Output Environmental Operating Temperature Storage Temperature Humidity 28 CAMLIVE 1 x HDMI Type A Female (Black) USB 3.1 Genl Type-C Male (White) or USB 3.1 Genl Type-A Male (via Dongle, Black) HDMI 1.4b, support 480p@60, 720p@60, and 1080p@60 (non-HDCP) 480p@60, 720p@60, and 1080p@60 YUV2, RGB 16-bit PCM audio, 32KHz, 44.1 KHz and 48KHz Up to 1080P UVC video stream with UAC audio (Uncompressed video stream is only available on USB3.1 connection) 0-40 oc -20 – 60 oc 0 – 80% RH, Non-Condensing
****** Page 37 ****** Function Minimum Hardware Requirement OS Support Physical Properties Housing Weight Dimensions (L x W x H) Appendix CAMLIVE PC/Mac: CPU: Intel@ i3 Dual Core 2.8Ghz or higher RAM: 4GB or more One USB-C Interface or USB-A Interface Smartphone: Android smartphone with UVC and USB-C interface Note: 1 . Latest IJC3020 firmware upgrade for smartphone support is required. 2. For detail UVC compatible device list, please review the following link of third part App camerafi.com/supported-devices/ Windows 7 and above with UVC support Mac OS X 10.13 and above with UVC support Android 5.0.1 and above with UVC support Note: 1 . Latest IJC3020 firmware upgrade for smartphone support is required. 2. For Windows 7 users, please download and install the Win7 driver from on our website. To download the driver, see Downloading the Firmware Upgrade Package, page 17. Aluminum 0.042kg (0.091b) 7.30 x 4.20 x 1.40 cm (2.87 x 1.65 x 0.55 in.) 29
****** Page 38 ****** CAMLIVE User Manual Limited Warranty ATEN warrants its hardware in the country of purchase against flaws in materials and workmanship for a Warranty Period of two  years (warranty period may vary in certain regions/countries) commencing on the date of original purchase. This warranty period includes the LCD panel of ATEN LCD KVM switches. Select products are warranted for an additional year (see A+ Warranty for further details). Cables and accessories are not covered by the Standard Warranty. What is covered by the Limited Hardware Warranty ATEN will provide a repair service, without charge, during the Warranty Period. If a product is detective, ATEN will, at its discretion, have the option to (1 ) repair said product with new or repaired components, or (2) replace the entire product with an identical product or with a similar product which fulfills the same function as the defective product. Replaced products assume the warranty of the original product for the remaining period or a period of 90 days, whichever is longer. When the products or components are replaced, the replacing articles shall become customer property and the replaced articles shall become the property of ATEN To learn more about our warranty policies, please visit our website: aten.com/global/en/legal/policies/warranty-policy 30
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL