Click here to download ASUSTEK H310I-IM-B (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** H3101-lM-B

****** Page 2 ****** El 6437 First Edition March 2020 Copyright 0 2020 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”). Product warranty or service will not be extended if: (1 ) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL “AS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR Loss ÖF PROFITS. LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY. AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Prodwts and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Offer to Provide Source Code of Certain Software This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product. Where the applicable license entitles you to the source code of such software and/or other additional data, you may obtain it for a period of three years after our last shipment of the product, either (1) for free by downloading it from https-//vmw.asus.com/support/ or (2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location where you want to have it shipped to, by sending a request to: ASUSTeK Computer lnc Legal Compliance Dept. IF., 15, Lide Rd , Beitou Dist. Taipei City 112 Taiwan In your request please provide the namer model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you. The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code. This offer is valid to anyone in receipt of this information. ASUSTeK is eager to duly provide complete source code as required under various Free Open Source Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address qpl@asus.com, stating the product and describing the problem (please DO NOT send large attachments such as source code archives, etc. to this email address) ii

****** Page 3 ****** Contents Chapter 1 Product overview 1-1 .. .. 1-2 ….. …… 2-2 2-4 2-5 1.1 1.2 1.3 Package contents Features ….. ….. ….. ….. ………………………………. Specifications .. Chapter 2 Motherboard information 2.1 2.2 2.3 2.4 2.5 2.6 Before you proceed . Motherboard layout………………………………………. Central Processing Unit (CPU) Installing the CPU 2.3.1 2.3.2 CPU heatsink and fan assembly installation System memory ……………….. . 2-9 Jumpers …………………………………………………………………………..2 10 Connectors 2-14 2.6.1 2.6.2 Chapter 3 Rear panel connectors 2-14 Internal connectors 2-16 BIOS setup 3.1 3.2 3.3 BIOS setup program 3-1 3.1.1 BIOS menu screen 3-2 Main menu 3 2 3.2.1 system Date [Day MM/DD/YYYY] 3.2.2 system Time 3-2 3-2 Advanced menu 3-3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 3.3.9 3.3.10 3.3.11 3.3.12 Start ASUS EzFlash 3-3 PCH-FW Configuration . Trusted Computing Platform Misc Configuration . 3-3 3-3 3-3 CPU Configuration 3-4 System Agent (SA) Configuration 3-5 PCH Storage Configuration . Onboard Devices Configuration. ACPI Settings . 3-6 3-6 3-8 LVDS Configuration 3-8 APM Configuration 3-8 NCT6110 super 10 Configuration . . 3-9

****** Page 4 ****** 3.3.13 3.3.14 3.3.15 3.3.16 3.3.17 3.3.18 3.3.19 NCT6116D HW Monitor ….. ….. ….. ………………… Serial Port Console Redirection……………………………… USB Configuration . NVMe Configuration. HDD Secure Erase . Dynamic Digital 10 Network Stack Configuration . 3-10 3-13 3-13 3-14 . 3-14 3-14 . 3-15 3-15 3.4 3.5 3.6 Save & Exit menu ……………………………………………………………..3 19 3.7 Security menu Boot menu 3-17 Event Logs 3.7.1 3.7.2 Appendix Notices Change Smbios Event Log Settings ….. ….. ….. ….. .. View Smbios Event Log 3-19 . 3-19 3-20

****** Page 5 ****** Chapter 1 Product overview 1.1 Package contents Check your industrial motherboard package for the following items. 1 ASUS H3101-lM-B Motherboard 1 x Serial 6.0 cables 2 x M.2 screw packages 1 ASUS 1/0 Shield NOTE: If any of the above items is damaged or missing, contact your distributor or sales representative immediately. 1.2 Features Intel@socket 1151 for the 9th/8th Gen InteP CoreTM i7/ i5/ i3, Pentium@, and Celeron@ processors Two Dual Channel DDR4 2666/2400/2133MHz Non-ECC so-DIMMs up to 32GB 4 x SATA 6.0 Gb/s, 4 x USB 3.2 Gen 1, 5 x USB 2.0, 4 x COM headers 1 x PCle x16 slotJ 1 x M.2 (Key E, 2230) for Wi-Fi/BT devices, 1 x M.2 (Key M, 2242/2260/2280) with PCle mode for SSD Mufti-display: 1 x DisplayPort, 1 x DVI-D, 1 x LVDS or eDP Chapter 1: General information 1-1

****** Page 6 ****** 1.3 CPU Specifications Chipset Memory Graphics Expansion slots Storage LAN Audio Rear panel 1/0 ports Internal 1/0 ports 1-2 InteP socket 1151 for / Gen InteP Corem i7/ i5/ i3, Pentiume, and Celerona processors Supports InteP 14nm CPU Supports up to 65W TDP InteP H310 Chipset 2 x SO-DIMMs, max.32GB, DDR4 2666/2400/2133 MHz SDRAM Integrated graphics processor – InteP HD Graphics support Multi-VGA output support: DP/DVl-D/LVDS/eDP ports – Supports DVI-D output with a maximum resolution of 1 920 x 1200 @ 60Hz Supports lx DisplayPort 1.2 output with a maximum resolution of 4096 x 2160 @ 60 Hz Supports LVDS output with a maximum resolution of 1920 x 1200 @ 60Hz Supports 2 lanes Embedded Display Port output with a maximum resolution of 1 920 x 1200 @ 60Hz (co-lay with LVDS) I x PCl Express 3.0/2.0 x16 slot I x M.2 socket I (Key E 2230) for WiFi/BT device supports PCIE and CNVi WiFi module 1 x M.2 socket 3 (Key M, 2242/2260/2280) with PCle mode 4 x SATA Gen3.0 up to 6.0 Gb/s ports Dual InteP Lan: 1 x InteP 121911, 1 x InteP i21 IAT Realtek ALC887-VD2 High Definition Audio I x DVI-D port I x DP port 2 x USB 3.2 Gen 1 ports 3 x USB 2.0 ports 2 x LAN (RJ45) ports 1 x P/S2 keyboard port 1 x P/S2 mouse port I x COM port (RS232/422/485) 2 x Audio jacks 3 x COM headers(3 x RS232) 1 x USB 3.2 Gen 1 header supports additional 2 USB 3.2 Gen 1 ports 1 x USB 2.0 header supports additional 2 USB 2.0 ports (continued on the next page) 1-13101-IM-B

****** Page 7 ****** Internal 1/0 ports GPIO Manageability Watch dog timer Power requirement Operation Temperature Non.Operation Temperature Relative Humidity OS support Certification Form Factor 1 x CPU Fan header (PWM mode) 1 x Chassis Fan header supports DC/PWM mode 1 x Chassis intrusion header 1 x Front panel audio header(AAFP) 1 x System panel header 1 x Clear CMOS jumper 1 x Speaker header 1 x LPC Debug header 1 x SIPDIF connector 1 x 12C header 1 x GPIO header 1 x AT/ATX mode selection header 1 x 24-pin ATX power connector 1 x 4-pin ATX power connector 1 x SPI TPM header 1 x WDT-EN header 1 x M.2 socket 1 (Key E, 2230) for WiFi/BT device supports PCIE and CNVi WiFi module 1 x M.2 socket 3 (Key M, 2242/2260/2280) with PCle mode 4 x SATA 6.0Gb/s connectors 1 x 8-bit GPIO header WIM 2.0, DMI 2.0, WOL by PME Yes AT/ATX mode DC in 12V 850 85 Windows@ 10 (64-bit) Windows@ 10 IoT Enterprise Ubuntu RedHat Enterprise Fedora Workstation OpenSUSE CE, FCC Mini-ITX Form Factor, 6.7″x 6.7″ (17.Ocm x 17.Ocm) NOTE: Specifications are subject to change without notice. Chapter 1: General information 1-3

****** Page 8 ****** 1-4 1-13101-IM-B

****** Page 9 ****** Chapter 2 Motherboard information 2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. CAUTION! Unplug the power cord from the wall socket before touching any component. Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity. Hold components by the edges to avoid touching the ICs on them. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component. Before you install or remove any component, always remove the AC power by unplugging the power cord from the power outlet. Failure to do so may cause severe damage to the motherboard, peripherals, or components. Chapter 2: Motherboard information 2-1

****** Page 10 ****** 2.2 Place thls slde towards the rear ot the chassls 2-2 Motherboard layout NOTE: Place four screws into the holes indicated by circles to secure the motherboard to the chassis. CAUTION! Do not overtighten the screws! Doing so can damage the motherboard. 17.Ocm(6.7in) cpu FAN • QüüOOüüQOOOO ATAEC 1 LIE 7B SATAE 2 SATAE S caus SATAEC_• 29 28 27 26 25 24 22 KBMS usag SEL USEI 12 o ATX12V 7 LGA1151 ODR4SO-OlMM Blf ODR4SO-OlMM PClEX16 CHA FAN TPM InteP 14310 O o Super MAWFI)- M. 2_ESOCkE aa•aaa 18 17 16 11 8 I-AN2 usa5ö LANI ua2G1 AUDIO 20 19 1-13101-IM-B

****** Page 11 ****** Connectors/Jumpers/Slots 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. CPU and chassis fan connectors (4-pin CPU FANJ 4-pin CHA FAN) Display panel VCC power selection (6-pin VCC_PWR_SEL) ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) USB 3.2 Gen I connector (20-1 pin U32Gl 12) SATA 6.OGb/s connectors (7-pin SATA6G_l -4) LPC debug header SPI TPM connector (14-1 pin SPI TPM) Serial port connectors (10-1 pin COM2J COM3J COM4) USB 2.0 connector (10-1 pin USB78) M.2 Wi-Fi Embedded DisplayPort (eDP) Speaker connector (4-1 pin SPEAKER) Chassis Intrusion header (4-pin CHASSIS) System panel connector (10-1 pin F_PANEL) M.2 socket 3 PC connector AT/ATX mode selection (3-pin AT_ATX_SEL) WDT Enbale jumper (2-pin WDT EN) Clear RTC RAM (2-pin CLRTC) Front panel audio connector (10-1 pin AAFP) DDR4 SO-DIMM slots IntePLGA1151 CPU socket RTC Battery header (2-pin BATT_CON) General purpose input/output connector (GPIO CON) Digital audio connector (4-1 pin SPDIF_OUT) LVDS connector (30-pin LVDS) Flat panel display brightness connector (6-pin LCD_BLKT_PANEL) Display panel backlight power selection (3-pin BKLT_PWR_SEL) Back Light power enable selection (3-pin BKLTEN SEL) Chapter 2: Motherboard information Page 2-18 2-11 2-25 2-16 2-19 2-22 2-18 2-23 2-17 2-21 2-16 2-20 2-13 2-19 2-21 2-22 2-11 2-12 2-10 2-24 2-9 2-4 2-20 2-17 2-24 2-20 2-23 2-10 2-12 2-3

****** Page 12 ****** Central Processing Unit (CPU) 2.3 The motherboard comes with a surface mount LGAI 151 socket designed for the InteP 9th/8th Generation CoreTM i7 / CoreTM i5 / CoreTM i3J Pentium@, and Celeron@ processors. O IMPORTANT: CAUTION! Unplug all power cables before installing the CPU. 2-4 Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. The manufacturer will shoulder the cost of repair only if the damage is shipment/trarEit-related. Keep the cap after installing the motherboard. The manufacturer will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGAI 151 socket. The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/ incorrect removal of the PnP cap. 1-13101-IM-B

****** Page 13 ****** 2.3.1 Installing the CPU CAUTION! LGAI 156 CPU is not compatible with the LGAI 151 socket. DO NOT install an LGAI 156 CPU on the LGAI 151 socket. Chapter 2: Motherboard information 2-5

****** Page 14 ****** -azz.-.-

****** Page 15 ****** 2.3.2 CPU heatsink and fan assembly installation CAUTION! Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary. To install the CPU heatsink and fan assembly 0 Chapter 2: Motherboard information o 2-7

****** Page 16 ****** To uninstall the CPU heatsink and fan assembly 2-8 1-13101-IM-B

****** Page 17 ****** 2.4 System memory This motherboard comes with two Double Data Rate 4 (DDR4) Small Outline Dual Inline Memory Module (SO-DIMM) sockets. The figure below illustrates the location of the DDR4 SO-DIMM sockets: SO-DIMM SO-DIMM Recommended memory configuration Installing a DIMM To remove a DIMM Chapter 2: Motherboard information Channel Channel A Channel B O Sockets SO-DIMM SO-DIMM O 2-9

****** Page 18 ****** 2.5 Jumpers 1. 2. 2-10 Clear RTC RAM (2.Pin CLRTC) This header allows you to clear the CMOS RTC RAM data of the system setup information such as date, time, and system passwords. CLRTC HEADER lx2p, 2.54mm pitch, sn Connector type To erase the RTC RAM: 1. 2. 3. 4. Turn OFF the computer and unplug the power cord. Use a metal object such a screwdriver to short the two pins. Plug the power cord and turn ON the computer. Hold down the key during the boot process and enter BIOS setup to re-enter data. NOTE: If the steps above do not help, remove the onboard battery and move the jumper again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery. Display panel backlight power selection (3•pin BLKT_PWR_SEL) BKLPWR_SEL 12V 5V (Default) Connector type 12V Pins 1-2 2-3 (Default) HEADER lx3p, 2.54mm pitch, SIT 1-13101-IM-B

****** Page 19 ****** 3. 4. Display panel VCC power selection (6•pin VCC_PWR_SEL) Setting 3.3V (Default) 12V 3.3V 12V (Default) Pins 1-2 3-4 5-6 HEADER 2 x 2.54mm pitch, SIT AT/ATX mode selection (3•pin AT_ATX_SEL) ATX mode (Default) ATX mode AT mode HEADER lx3p, 2.54mm pitch, sn AT mode Pins 1-2 (Default) 2-3 Connector type Chapter 2: Motherboard information 2-11

****** Page 20 ****** 5. 6. 2-12 WDT Enable jumper (2•pin WDT_EN) A watchdog timer is an electronic timer that is used to detect and recover from computer malfunctions. The HW WDT (watchdog timer) Enable jumper allows the HW watchdog resets the system automatically even when the system crashes. WDT EN HEADER lx2pj 2.54mm pitch, sn NOTE: By default, this jumper is set to HW WDT enabled with a jumper cap attached. Back Light power enable mode (B KLTEN_SEL) Pins 1-2 (Default) 2-3 Connector type BKLTEN SEL 123 High Active Low Active HEADER lx3p, 2.54mm pitch, SIT 1-13101-IM-B

****** Page 21 ****** 7. Chassis intrusion header (4•1 pin_CHASSlS) This header is for a chæsis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a low-level signal to this connector when a chæsis component is installed. The signal is then generated as a chassis intrusion event. CHASSIS Connector type Chassis Intruder – Close 3-4jumper removed (Default) HEADER4p,K2, 2S4mm pitch Chapter 2: Motherboard information Chæsis Intruder – Open 3-4jumper closed 2-13

****** Page 22 ****** 2.6 2.6.1 1 10 Connectors Rear panel connectors 2 0 00000 0 0000 o 3 7 9 8 7 6 4 5 1. 2. 3. 4. 5. 6. 2-14 PSD mouse port (green). This port is for a PS/2 mouse. Serial port connector (COM). This port connects a modem, or other devices that conform with serial specification. LAN (RJ•45) ports. These ports allow Gigabit connection to a Local Area Network (LAN) through a network hub. LAN port LED indications Activityn-ink LED Status Off Orange Orange (Blinking) Orange (Blinking then stea Speed LED Actlvlty I-Ink LED Speed LED Description No link Linked Data activity Ready to wake u from S5 mode Status OFF ORANGE GREEN Description 10Mbps connection 100Mbps connection 1 Gbps connection LAN port Line In port (light blue). This port connects to the tape, CD, DVD player, or other audio sources. Line Out port (lime). This port connects to a headphone or a speaker. In the 4.1, and 5.1 channel configurations, the function of this port becomes Front Speaker Out. USB 3.2 Gen 1 (up to 5Gbps) ports. These 9-pin Universal Serial Bus (USB) ports are for USB 3.2 Gen 1 devices. 1-13101-IM-B

****** Page 23 ****** 7. 8. 9. 10. USB 3.2 Gen 1 devices can only be used for data storage. We strongly recommend that you connect USB 3.2 Gen 1 devices to USB 3.2 Gen 1 ports for faster and better performance from your USB 3.2 Gen 1 devices. Due to the design of the InteP 300 series chipset, all USB devices connected to the USB 2.0 and USB 3.2 Gen 1 ports are controlled by the xHCl controller. Some legacy USB devices must update their firmware for better compatibility. USB 2.0 ports. These 4-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1 devices. DVI•D port. This port is for any DVI-D compatible device. DVI-D can not be converted to output from RGB Signal to CRT and is not compatible with DVI-I. DisplayPort. This port is for DisplayPort-compatible devices. PSD keyboard port (purple). This port is for a PS/2 keyboard. Chapter 2: Motherboard information 2-15

****** Page 24 ****** 2.62 Internal connectors 1. 2. 2-16 USB 3.2 Gen 1 connector (20-1 pin U32G1_12) Connect a USB 3.2 Gen 1 module to this connector for additional USB 3.2 Gen 1 front or rear panel ports. This connector complies with USB 3.2 Gen 1 specifications and provides faster data transfer speeds of up to 5 Gbps, fæter charging time for USB-chargeable devices, optimized power efficiency, and backward compatibility with USB 2.0. Connector type BOX HD mop, 2.0mm pitch Embedded DisplayPort (40- pin eDP) This connector is for an internal embedded DisplayPort connection. NC BLKT BLKT-PV/R NC NC S avo-TCTL I-CT ENÅBR-T CN GNO GNO GNO BOP HPO -GND GNO GNO GNO NC LCD VCC LCDÄ.’CC LCDÄ.’CC -GND SW OUT AUX C N SW CUT C SW-OUT-eæm-c SW CUT eDPIP C SW-OUT-BLF IN -c NC NC GNO NC NC GNO NC EDP PIN 1 Connector type WtoB CON 40p, 0.5mm pitch, R/A 1-13101-IM-B

****** Page 25 ****** 3. 4. USB 2.0 connector (10.pin USB78) This connector is for an USB 2.0 port. Connect the USB cable to this connector. This USB connector complies with USB 2.0 specification that supports up to 480 Mbps connection speed. USB78 PIN 1 Header 2x5p, K9, 2.54mm pitch CAUTION! Never connect a 1394 cable to the USB connector. Doing so will damage the motherboard. NOTE: The USB cable is purchased separately. General purpose input/output connector (GPIO CON) This connector is for a general purpose input/output module which allows you to customize the digital signal input/output. GPIO_CON +5VSB GP105 GP103 GPIOI GND GP108 GP106 GP104 GP102 Connector type WAFER HD 2x5p, 2.0mm pitch, SIT Chapter 2: Motherboard information 2-17

****** Page 26 ****** 5. 6. 2-18 CPU and chassis fan connectors (4•pin CPU_FAN, a-pin CHA_FAN) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. CPU CHA o GND 12V FAN IN FAN PIWI FAN WAFER HD 2.54mm pitch, SIT Connector type CAUTION: Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! TPM connector (14-1 pin SPI_TPM) This connector supports a Trusted Platform Module (TPM) system with a Serial Peripheral Interface (SPI), allowing you to securely store keys, digital certificates, passwords and data. A TPM system also enhances network security, protects digital identities, and ensures platform integrity. TPM Header 2x7p, KI 4, 2.0mm pitch 1-13101-IM-B

****** Page 27 ****** 7. 8. Front panel system panel connector (10-1 pin F_PANEL) This connector supports several chassis-mounted functions. F_pANEL GND PWRBTN# PANEL PLED PLED+ Header 2x5p, KI O, 2.54mm pitch Connector type System power LED (2.Pin *PWR LED) O RSTCON# GND HDD LED- R HDD LED+ PIN 1 PR This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity LED (2•pin +HDD_LED) This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The IDE LED lights up or flæhes when data is read from or written to the HDD. ATX power button/soft•off button (2•pin PWR BTN) This 2-pin connector is for the system power button. Reset button (2.Pin RESET) This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power. Serial ATA 6.0Gb/s connectors (7.pin SATA6G_112/3/4) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives or an optical drive via Serial ATA 6.0 Gb/s signal cables. SATA6G 1 SATA6G 2 SATA6G 3 SATA6G 4 WAFER HD 1.27mm pitch Chapter 2: Motherboard information 2-19

****** Page 28 ****** 9. 10. 11. 2-20 LVDS connector (30•pin LVDS) This connector is for an LCD monitor that supports Low Voltage Differential Signalling (LVDS) interface. L VDS O TX TDIN R I-iOS TX TCLKIN-R LV5s tx TCIN-R LVDSTTTBIN-R LVDSTVTAIN-R TX TOON R I-iOS TX I-VOS TX -rcou-a LVDSTX-TBOBER LVDS-TVTAON-R LCD vec -GNO GNO LCD VCC PIN I I-VOS TX TOIP R I-VOS-TX-TCLKIP R I-YOSTXÄCIP R- I-VOS-TX-TBIP-R GND I-VOS TX R I-hvos-TFTCLKÜP R I-VOS-TX-TCff3 R I-VOS-TX-TBCVR I-VOS-TX-TAVA DAV I-VOS-DOCTCL GND I VCC WAFER HD 2x15p, 1.25mm pitch Speaker connector (4•pin SPEAKER) The 4-pin connector is for the chæsis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. SPEAKER SPKO GND GND PIN I HEADER lx4p, 2.54mm pitch, SIT RTC battery connector (2•pin BATT_CON) This connector is for the lithium CMOS battery. BATT CON GND VBAT 1-13101-IM-B

****** Page 29 ****** 12. 13. M.2 socket 3 This socket allows you to install an M.2 SSD module. M .2(SOCKET3) zaao 0 o NOTES: • The M.2 SSD module is purchased separately. • This socket supports M Key and 2242/2260/2280 storage devices. M.2 WiFi This socket connects to an M.2 Wi-Fi device. M.2(WlFl) NOTE: The M .2 Wi-Fi module is purchased separately. Chapter 2: Motherboard information 2-21

****** Page 30 ****** 14. 15. 2-22 LPC Debug header This header allows connection to a LPC debug card. LPC_DEBUG QQQQt ddddi Connector type HEADER 2x5p, KIO, 2.0mm pitch IMPORTANT! Scan the QR code to view the meaning of each debug code. • Debug codes are only available for ASUS LPC debug card. Contact your region sales representative for LPC debug header ordering. 12C connector The PC (Inter-lntegrated Circuit) connector allows you to connect an PC compatible IoT security module. Connector type 12C PIN 1 Header 2x3p, K6, 2.0mm pitch 1-13101-IM-B

****** Page 31 ****** 16. 17. Serial port connectors (10•pin COM2, COM3, COM4) These connectors are for serial (COM) ports. Connect the serial port cables to these connectors, then install the module to a slot opening at the back of the system chassis. COM2, COM3s COM4 PIN 1 o BOX header 2x5p, KIO, 2.0mm pitch NOTE: The serial port cables are purchased separately. Flat panel display brightness connector (6•pin LCD_BLKT_PANEL) This connector is for the LCD panel brightness controls. LCD BLKT PANEL BKL BKLTWR LCD-ENABKLT CN LCD-BL PWM ON GND- GND Connector type WAFER 6p, 2.0mm pitch Chapter 2: Motherboard information 2-23

****** Page 32 ****** 18. 19. Digital audio connector (4-1 pin SPDIF OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chæsis. SPDIF OUT GND SPDIFO PIN I NOTE: HEADER lx4p, 2.54mm pitch The SPDIF Out module is purchased separately. Front panel audio connector (10•1 pin AAFP) This connector is for a chassis-mounted front panel audio 1/0 module that supports HD Audio standard. Connect one end of the front panel audio 1/0 module cable to this connector. 0 I..LI AAFP PIN I o I-L LL a— I o o a. 2-24 HEADER 2x5p, K8, 2.54mm pitch Connector type IMPORTANT! We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability. If you want to connect a high-definition front panel audio module to this connector. set the HD Audio Controller item in the BIOS setup to [Enabled]. 1-13101-IM-B

****** Page 33 ****** 20. ATX power connectors (24•pin EATXPWR, 4•pin ATX12V) Correctly orient the ATX power supply plugs into these connectors and push down firmly until the connectors completely fit. O EATXPWR z z zo PIN I Z Z Z Z 1.0 z o O ATX12V GND GND +12V_OPU +12V_OPU DC Mode EATXPWR Pins 1 2 3 4 5 6 7 8 9 10 11 12 DC Mode ATX12V Pins 1 2 Signal +3.3V OUT +3.3V OUT GND +5V OUT GND +5V OUT GND NC NC +12V IN +12V IN +3.3V OUT Signal GND GND Pins 13 14 15 16 17 18 19 20 21 22 23 24 Pins 3 4 Signal +3.3V OUT NC GND NC GND GND GND +12V OUT +5V OUT +5V OUT +5V OUT GND Signal +12V IN +12V IN Chapter 2: Motherboard information 2-25

****** Page 34 ****** 2-26 1-13101-IM-B

****** Page 35 ****** Chapter 3 BIOS setup Scan the QR code to view the BIOS update guide. 3.1 BIOS setup program Use the BIOS Setup program to update the BIOS or configure its pararneters. The BIOS screens include navigation keys and brief online help to guide you in using the BIOS Setup program. Entering BIOS Setup at startup To enter BIOS Setup at startup: Press or during the Power-On Self Test (POST). If you do not press or POST continues with its routines. Entering BIOS Setup after POST To enter BIOS setup after POST: • Press simultaneously. • Press the reset button on the system chassis. Press the power button to turn the system oft then back on. Do this option only if you failed to enter BIOS Setup using the first two options. NOTE: Using the power button, reset button, or the ++ keys to reboot a running operating system can cause damage to your data or system. Always shut down the system properly from the operating system. IMPORTANT: Visit the ASUS website at asus.com to download the latest BIOS file for this motherboard. The default BIOS settings for this motherboard apply to most working conditions and ensures optimal performance. If the system becomes unstable after changing any BIOS settings, load the default settings to regain system stability. Select the option Restore Defaults under the Exit Menu or press hotkey FS. The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen. Chapter 3: BIOS setup 3-1

****** Page 36 ****** 3.1.1 BIOS menu screen Menu bar The menu bar on top of the screen hæ the following main items: Main Advanced Security Boot Save & Exit Event Logs For changing the basic system configuration For changing the advanced system settings For configuring the system security settings For changing the system boot configuration. For selecting the save options and default options. For enabling easier troubleshooting by capturing useful system information. To select an item on the menu bar, press the right or left arrow key on the keyboard until the desired item is highlighted. 3.2 Main menu The Main menu provides you an overview of the basic system information, and alloys you to set the system date, time, language, and security settings. 3.2.1 System Date [Day MM/DD/YYYYI Allows you to set the system date. 3.2.2 System Time Allows you to set the system time. 3-2 1-13101-IM-B

****** Page 37 ****** 3.3 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. 3.3.1 Start ASUS EzFlash This item allows you to run EzFlash utility. When you press a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press to confirm your choice. 3.3.2 PCH-FW Configuration TPM Device Selection This item allows you to select the TPM device. Configuration options: [dTPM] [PTT] 3.3.3 Trusted Computing Security Device Support This item alloys you to enable or disable BIOS support for security devices. Configuration options: [Disabled] [Enabled] 3.3.4 Platform Misc Configuration The items in this menu allow you to configure the platform-related features. Native PCIE Enable The following item appears only when you set the Native PCIE Enable to [Enabled]. Native ASPM [Enabled] [Disabled] PCH • PCl Express PCH DMI ASPM OS controls the ASPM (active state power management) support for devices. BIOS controls the ASPM support for the device. This item allus you to control the Active State Power Management on both NB (NorthBridge) side and SB (SouthBridge) side of the DMI Link. Configuration options: [Disabled] [LOS] [Ll] [LOsL1] [Auto] ASPM O This item a110/S you to select the ASPM state for energy-saving conditions. Configuration options: [Disabled] [LOS] [L 1] [LOsL1] [Auto] Chapter 3: BIOS setup 3-3

****** Page 38 ****** 3-4 Ll Substates This item a110/S you to select the PCl Express Ll Substates settings. Configuration options: [Disabled] [Ll .1] [Ll .1 & Ll .2] SA • PCl Express DMI Link ASPM Control This item a110/S you to control the Active State Power Management on both CPU and PCH (platform controller hub) Both DMI link ASPM control items of the CPU and PCH sides must be enabled for the ASPM to take effect. Configuration options: [Disabled] [LOS] [L 1] [LOsL1] ASPM This item allows you to control ASPM for PEG 0. This hæ no effect if PEG is not the currently active device. Configuration options: [Disabled] [Auto] [ASPM LOS] [ASPM L 1] [ASPM LOsL1] 3.3.5 CPU Configuration The items in this menu show CPU-related information the BIOS automatically detects. The items shown in the submenu may be different depending on the type of CPU installed. Software Guard Extensions (SGX) This item enables/disables the Software Guard Extensions (SGX). Configuration options: [Disabled] [Software Controlled] [Enabled] Hardware Prefetcher This item allows you to turn on/off the MLC streamer prefetcher. Configuration options: [Disabled] [Enabled] Adjacent Cache Line Prefetcher This item allows you to turn on/off prefetching adjacent cache lines. Configuration options: [Disabled] [Enabled] Intel (VMX) Virtualization Technology When set to [Enabled], a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. Configuration options: [Disabled] [Enabled] Active Processor Cores This item a110/S you to select the number of CPU cores to activate in each processor package. Configuration options: [All] [1] [2] [3] [4] [5] For some CPU types, only [All] and [1] appear. 1-13101-IM-B

****** Page 39 ****** Hyper-threading The Intel Hyper-Threading Technology allows a hyper-threading processor to appear two logical processors to the operating system, allowing the operating system to schedule two threads or processes simultaneously. [Enabled] Two threads per activated core are enabled. Only one thread per activated core is enabled. [Disabled] CPU Power Management Control This item allows you to manage and configure the CPUS power. Boot performance mode This item allows you to select the CPU performance state that the BIOS will set starting from reset vector. Configuration options: [Max Battery] [Max Non-Turbo Performance] [Turo Performance] Intel(R) SpeedStep(tm) This item allows your system to support more than two frequency ranges. Configuration options: [Disabled] [Enabled] Intel(R) Speed Shift Technology This item allows you to enable or disable Intel(R) Speed Shift Technology support. When enabled, CPPC v2 interface allows hardware controlled P-state. Configuration options: [Disabled] [Enabled] Turbo Mode This item allows you to enable or disable Turbo Mode for your processor. Configuration options: [Enabled] [Disabled] Turbo Mode is available only when InteP Speed Step or InteP Speed Shift is enabled. 3.3.6 System Agent (SA) Configuration Graphics Configuration Allows you to select a primary display from IGFX, PEG and PCl graphical devices. Primary Display [Auto] Allows you to select which of the IGFX/PEG/PCI Graphics device should be the Primary Display or to select SG for switchable Gfx. Configuration options: [Auto] [IGFX] [PEG] VT.d [Disabled] Allows you to enable or disable VT-d function on MCH. Configuration options: [Enabled] [Disabled] Chapter 3: BIOS setup 3-5

****** Page 40 ****** 3.3.7 PCH Storage Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Empty if no SATA device is installed to the corresponding SATA port. SATA Controller(s) Enables or disables onboard the SATA device. Configuration options: [Disabled] [Enabled] The following items appear only when you set SATA Controller(s) to [Enabled] Smart Self Test This item a110/S you to enable or disable the SMART Self Test on all HDDs during POST. Configuration options: [Disabled] [Enabled] SATA Mode Selection This item allows you to set the SATA configuration. [AHCI] [Intel RST Premium With Intel Optane System Acceleration] Set to [AHCI] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands. Set to [Intel RST Premium With Intel Optane System Acceleration] when you want to create a RAID configuration from the SATA hard disk drives. Aggressive LPM Support This item is designed for LPM (link power management) support with a better energy saving conditions. When disabled, the hot plug function of SATA ports are disabled. Configuration options: [Disabled] [Enabled] Hot Plug These items allow you to enable/disable SATA Hot Plug Support. Configuration options: [Disabled] [Enabled] SATA6G_1 N4(Gray) Allow you to enable/disable the SATA6G_1-4 port. Configuration options: [Disabled] [Enabled] 3.3.8 Onboard Devices Configuration HD Audio Controller [Enabled] Enables the HD Audio Device. 3-6 1-13101-IM-B

****** Page 41 ****** [Disabled] Disables the HD Audio Device. Intel LAN Controller [Enabled] Enables the Intel LAN controller. [Disabled] Disables the controller. The following item appears only when you set Intel LAN Controller to [Enabled]. Intel LAN PXE OPROM This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the PXE Option ROM of the Intel LAN controller. Configuration options: [Disabled] [Enabled] Intel LAN2 Controller [Enabled] Enables the Intel LAN2 controller. [Disabled] Disables the controller. The following item appears only when you set Intel LAN2 Controller to [Enabled]. Intel LAN2 PXE OPROM This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the PXE Option ROM of the Intel LAN2 controller. Configuration options: [Disabled] [Enabled] M.2 WiFi(E.Key) Connectivity mode (Wi-Fi & Bluetooth) This item allows you to enable or disable the Wi-Fi and Bluetooth connectivity module. Configuration options: [Disabled] [Enabled] 12C1 Controller This item allows you to enable or disable the Serial 10 Controller. Configuration options: [Enabled] [Disabled] Chapter 3: BIOS setup 3-7

****** Page 42 ****** 3.3.9 ACP’ Settings Enbale ACPI Auto Configuration This item allus you to enable or disable BIOS ACPI auto configuration. Configuration options: [Enabled] [Disabled] Enbale Hibernation This item allows you to enable or disable the system’s Hibernation (OS/S4 Sleep State). Configuration options: [Enabled] [Disabled] This option may not be available on some operating systerrz ACPI Sleep State Allows you to select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. Configuration options: [Suspend Disabled] [S3 (Suspend to RAM)] Lock Legacy Resources Allows you to enable or disable Lock of Legacy Resources. Configuration options: [Enabled] [Disabled] 3.3.10 LVDS Configuration LVDS Support Allows you to enable or disable LVDS. Configuration options: [Enabled] [Disabled] 3.3.11 APM Configuration Restore AC Power Loss The system goes into on state after an AC power loss. The system goes into off state after an AC power loss. Power On BY PCl.E This item allows you to enable or disable the Wake-on-LAN function of the onboard LAN controller or other installed PCle LAN cards. Configuration options: [Disabled] [Enabled] Power On By PS/2 Keyboard Enables or disables the system to be powered on by a PS/2 keyboard. Configuration options: [Disabled] [Enabled] Power On By PS/2 Mouse Enables or disables the system to be powered on by a PS/2 mouse. Configuration options: [Disabled] [Enabled] 38 1-13101-IM-B

****** Page 43 ****** Power On By Ring [Enabled] Enables the Ring devices to generate a wake event. [Disabled] Disables the Ring devices to generate a wake event. Power On BY RTC [Enabled] [Disabled] When set to [Enabled], the items RTC Alarm Date(Days) and Hour/ Minute/Second are use-configurable with set values. Disables RTC to generate a wake event. 3.3.12 NCT6116D super 10 Configuration Serial Port 1 Configuration Serial Port Allows you to enable or disable the serial port (COM).Configuration options: [Disabled] [Enabled] The following items appear only when you set Serial Port to [Enabled]. Mode Select Allows you to select the Serial Port mode. Configuration options: [RS2321 IRS4221 IRS4851 Change Settings Allows you to select an optimal setting for Super 1/0 devices. Configuration options: [Autol 110=3F8h; 110=3F8h; 1 , 12;] [10=2F8h; I o, I I 2;] [10=3E8h; 1 0111.12;] [10=2E8h; Serial Port 2 Configuration Serial Port Allows you to enable or disable the serial port (COM).Configuration options: [Disabled] [Enabled] The following item appears only when you set Serial Port to [Enabled]. Change Settings Allows you to select an optimal setting for Super 1/0 devices. Configuration options: [Autol 110=2F8h; IRQ=3;] 110=3F8h; 0, 1 1 , 12;] [10=2F8h; 10,1 1 , 1 2;] 110=3E8h; 1 1, 12;] [10=2E8h; Serial Port 3 Configuration Serial Port Allows you to enable or disable the serial port (COM).Configuration options: [Disabled] [Enabled] The following item appears only when you set Serial Port to [Enabled]. Chapter 3: BIOS setup 3-9

****** Page 44 ****** Change Settings Allows you to select an optimal setting for Super 1/0 devices. Configuration 1 0111 , 12;] [10=2FOh; 1 1 2;] 110=2EOh; Serial Port 4 Configuration Serial Port Alloys you to enable or disable the serial port (COM).Configuration options: [Disabled] [Enabled] The following item appears only when you set Serial Port to [Enabled] Change Settings Allows you to select an optimal setting for Super 1/0 devices. Configuration 1 0111 , 12;] [10=2FOh; 1 1 1 2;] 110=2EOh; 3.3.13 NCT6116D HW Monitor Q•Fan Configuration CPU Q•Fan Control Disables the CPU Q-Fan control feature. [Disabled] [PWM Mode] Enable the CPU Q-Fan control in PWM mode for 4-pin CPU fan. CPU Fan step UP/Down This item appears only when you enable the CPU Q-Fan Control feature and allows you to set the CPU Fan Step Up/Down time. Configuration options: [0 sec] [2.1 sec] [2.8 secl [3.6 sec] [4.2 sec] [5.0 secl [6.3 sec] [8.5 sec] [12 sec] [25 sec] CPU Fan Speed Low Limit This item appears only when you enable the CPU Q-Fan Control feature and allows you to disable or set the CPU fan warning speed. Configuration options: [Ignore] [200RPM] [300 RPM] [400 RPM] [500 RPM] [600RPM] CPU Fan Profile [Standard] This item appears only when you enable the CPU Q-Fan Control feature and allows you to set the appropriate performance level of the CPU fan. [Standard] [Silent] [Turbo] [Manual] 3-10 Sets to [Standard] to make the CPU fan automatically adjust depending on the CPU temperature. Sets to [Silent] to minimize the fan speed for quiet CPU fan operation. Sets to [Turbo] to achieve maximum CPU fan speed. Sets to [Manual] to GSign detailed fan speed control parameters. 1-13101-IM-B

****** Page 45 ****** The following four items appear only when you set CPU Fan Profile to [Manual]. CPU Upper Temperature Use the and keys to adjust the upper limit of the CPU temperature. The CPU fan will operate at the maximum duty cycle when the CPU temperature is higher than the limit. CPU Fan Max. Duty Use the and keys to adjust the maximum CPU fan duty cycle. When the CPU temperature reaches the upper limit, the CPU fan will operate at the maximum duty cycle. CPU Middle Temperature Use the and keys to adjust the CPU middle temperature. CPU Fan Middle. Duty Use the or keys to adjust the CPU fan middle duty cycle. CPU Lower Temperature Use the or keys to adjust the lower limit of the CPU temperature. The CPU fan will operate at the minimum duty cycle when the CPU temperature is lower than the limit. CPU Fan Min. Duty Use the and keys to adjust the minimum CPU fan duty cycle. When the CPU temperature is lower than the lower limit, the CPU fan will operate at the minimum duty cycle. Chassis Fan(s) Configuration Chassis Fanl Q•Fan Control This item allows you to set the chassis fan operating mode. [PWM Mode I [DC Mode] [Disabled] Enables the Chassis Fan Q-Fan Control feature in PWM mode for 4-pin chassis fan. Enables the Chassis Fan a-Fan Control feature in DC mode for 3-pin chassis fan. Disables the Q-Fan control. Chassis Fanl Q•Fan Source The assigned fan will be controlled according to the selected temperature source. Configuration options: [CPU] [MotherBoard] Chapter 3: BIOS setup 3-11

****** Page 46 ****** Chassis Fanl Step UPDown This item a110/S you to set the Chassis Fan Step Up/Down time. Configuration options: [0 secl [12 sec] [25 sec] [51 sec] [76 sec] [102 secl [127 sec] [153 [178 sec] [204 sec] Chassis Fanl Speed Low Limit This item alloys you to disable or set the chæsis fan warning speed. Configuration options: [Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM] Chassis Fanl Profile This item a110/S you to set the appropriate performance level of the chæsis fan. [Standard] Sets to [Standard] to make the chassis fan automatically adjust depending on the chassis temperature. [Silent] operation. [Turbo] [Manual] Sets to [Silent] to minimize the fan speed for quiet chæsis fan Sets to [Turbo] to achieve maximum chassis fan speed. Sets to [Manual] to æsign detailed fan speed control parameters. The following items appear only when you set Chassis Fanl Profile to [Manual]. Chassis Fanl Upper Temperature Use the or keys to adjust the upper limit of the Chassis Fanl temperature. The Chassis Fanl will operate at the maximum duty cycle when the temperature source is higher than the limit. Chassis Fanl Max. Duty Cycle (%) Use the or keys to adjust the maximum Chassis Fanl duty cycle. When the temperature source reaches the upper limit, the Chæsis Fanl will operate at the maximum duty cycle. Chassis Fanl Middle Temperature Use the or keys to adjust the middle limit of the Chæsis Fanl temperature. Chassis Fanl Middle. Duty Cycle (%) Use the or keys to adjust the Chæsis Fanl middle duty cycle. Chassis Fanl Lower Temperature Use the or keys to adjust the lower limit of the Chassis Fanl temperature. The Chassis Fanl will operate at the minimum duty cycle when the temperature source is lower than the limit. 3-12 1-13101-IM-B

****** Page 47 ****** Chassis Fanl Min. Duty Cycle(%) Use the or keys to adjust the minimum Chassis Fanl duty cycle. When the temperature source is under the limit, the Chassis Fanl will operate at the minimum duty cycle. 3.3.14 Serial Port Console Redirection Console Redirection Allows you enable or disable the console redirection feature. Configuration options: [Enabled] [Disabled] Legacy Console Redirection Settings Redirection COM Port Allows you to select a COM port to display redirection of Legacy OS and Legacy OPROM Messages. Configuration options: [COMI] [COM2] [COM3] [COM4] [COM5 (Disabled)] [COM6 (Disabled)] Resolution This allows you to set the number of rows and columns supported on the Legacy os. Configuration options: [80×24] [80×25] Redirection After POST This setting allows you to specify if Bootloader is selected than Legacy console redirection. [Always Enable] [Bootloader] Legacy Console Redirection is enabled for Legacy OS. Legacy Console Redirection is disabled before booting to Legacy OS. 3.3.15 USB Configuration The USB Devices item lists auto-detected values. If no USB device is detected, the item shows None. Legacy USB Support [Enabled] [Disabled] [Auto] Enables the support for USB devices on legacy operating systems (OS). USB devices are only available when running BIOS Setup. Allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Chapter 3: BIOS setup 3-13

****** Page 48 ****** XHCI Hand-off This item is set to [Disabled] by default for the EHCI (enhanced host controller interface) support by XHCI drivers in operating systems. [Disabled] [Enabled] Support XHCI by XHCI drivers for operating systems with XHCI support. Support XHCI by BIOS for operating systems without XHCI support. 3-14 USB Mass Storage Driver Support Allows you to enable or disable the USB Mass Storage driver support. Configuration options: [Disabled] [Enabled] USB Port Disable Override Allows you to selectively enable or disable the corresponding USB port from reporting a Device connection to the controller. U32G1 1-4 Allows you to enable or disable USB port. Once set to [Disabled], any USB devices plugged into the connector will not be detected by BIOS or OS. Configuration options: [Disabled] [Enabled] USB5-9 Allows you to enable or disable USB port. Once set to [Disabled], any USB devices plugged into the connector will not be detected by BIOS or OS. Configuration options: [Disabled] [Enabled] 3.3.16 NVMe Configuration This menu displays the NVMe controller and drive information of the connected devices. 3.3.17 HDD Secure Erase This menu displays the HDD that supports Secure Erase function. 3.3.18 Dynamic Digital 10 The items listed in this screen configure Digital 10 settings. DIO Direction Configuration options: [Input] [Output] The following item appears only when you set DIO 00 to [Output]. 1-13101-IM-B

****** Page 49 ****** Output Level [H] Configuration options: [H] [L] 3.3.19 Network Stack Configuration Network Stack This item allows user to disable or enable the UEFI network stack. Configuration options: [Disabled] [Enabled] The following two items appear only when you set the previous item to [Enabled]. Ipv4 PXE Support This item allows user to disable or enable the Ipv4 PXE Boot support. Configuration options: [Disabled] [Enabled] Ipv6 PXE Support This item allows user to disable or enable the Ipv6 PXE Boot support. Configuration options: [Disabled] [Enabled] 3.4 Security menu This menu allows a new password to be created or a current password to be changed. The menu also enables or disables the Secure Boot state and lets the user configure the System Mode state. Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. To set an administrator password: 1. Select the Administrator Password item and press . 2. From the Create New Password box, key in a password, then press . 3. Confirm the password when prompted. To change an administrator password: 1. 2. 3. 4. Select the Administrator Password item and press . From the Enter Current Password box, key in the current password, then press . From the Create New Password box, key in a new password, then press . Confirm the password when prompted. To clear the administrator password, follow the same steps as in changing an administrator password, but press when prompted to create/confirm the password. Chapter 3: BIOS setup 3-15

****** Page 50 ****** 3-16 User Password If you have set a user password, you must enter the user password for accessing the system. The User Password item on top of the screen shows the default Not Installed. After you set a password, this item shows Installed To set a user password: 1. Select the User Password item and press . 2. From the Create New Password box, key in a password, then press . 3. Confirm the password when prompted. To change a user password: 1. Select the User Password item and press 2. From the Enter Current Password box, key in the current password, then press 3. From the Create New Password box. key in a new password, then press . 4. Confirm the password when prompted. To clear a user password: 1 Select the Clear User Password item and press . 2. Select Yes from the Warning message window then press . Secure Boot Secure Boot can be enabled if the system is running in User mode with enrolled platform Key (EPK) or if the CSM function is disabled. Configuration options: [Disabled] [Enabled] Key Management The Key Management item allows you to modify Secure Boot variables and set Key Management page. Restore Factory Keys Force System to User Mode. Configure NVRAM to contain OEM-defined factory default Secure Boot keys. Reset to Setup Mode Delete NVRAM content of all UEFI Secure Boot key databases. Export Secure Boot Variables Copy NVRAM content of source Boot variables to files in a root folder on a file system device. Platform Key (PK) Configuration options: [Details] [Export] [Update] [Delete] Key Exchange Keys / Authorized Signatures / Forbidden Signatures Configuration options: [Details] [Export] [Update] [Append] [Delete] 1-13101-IM-B

****** Page 51 ****** 3.5 Boot menu The Boot menu items allow you to change the system boot options. CSM Configuration CSM Support This option allows you to enable or disable CSM Support. Configuration options: [Disabled] [Enabled] Fast Boot [Enabled] Select to accelerate the boot speed. [Enabled] Select to go back to normal boot speed. [Disabled] The following item appears only when you set Fast Boot to [Enabled]. SATA Support [Last Boot SATA Devices Only] Only last boot SATA device will be available in POST. [All SATA Devices] All SATA devices will be available in OS and POST. [HDD only] NVMe Support This item allows you to enable or disable NVMe Support. Configuration options: [Disabled] [Enabled] VGA Support [Autol [EFI Driverl USB Support [Disabled] [Full Initiall [Partial Initial] Only installs the Legacy OpRom with Legacy OS and logo will not be shown during POST. EFI driver will still be installed with the EFI OS. All USB devices will NOT be available until after OS boot. All USB devices will be available in OS and POST. USB Mass Storage and specific USB port/device will NOT be available before OS boot. Network Stack Driver Support [Disabled] [Enabled] Network Stack Driver will be skipped. Network Stack Driver will not be skipped. Redirection Support Allows you to enable or disable the Redirection function. Configuration options: [Disabled] [Enabled] Setup Prompt Timeout Allows you to set the number of seconds to wait for setup activation key. 65535(OxFFFF) means indefinite waiting. Configuration options: [1] – [65535] Chapter 3: BIOS setup 3-17

****** Page 52 ****** Boot up NumLock State [On] [Off] Set the power-on state of the NumLock to [On]. Set the power-on state of the NumLock to [Off]. Chassis Intrusion Detection Allows you to enable or disable the chassis intrusion detection function. Configuration options: [Disabled] [Enabled] Wait For ‘Fl’ If Error When this item is set to [Enabled], the system waits for the Fl key to be pressed when error occurs. Configuration options: [Disabled] [Enabled] Quiet Boot Allows you to enable or disable the Quiet Boot option. Configuration options: [Disabled] [Enabled] Boot Option Priorities These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system. To select the boot device during system startup, press when ASUS Logo appears. 3-18 1-13101-IM-B

****** Page 53 ****** 3.6 Save & Exit menu The Save & Exit menu items allow you to save or discard your changes to the BIOS items. Discard Changes & Exit This option allows you to exit the Setup program without saving your changes. When you select this option or if you press a confirmation window appears. Select Yes to discard changes and exit. Save Changes & Reset This option allows you to exit the Setup program after saving changes. Restore Defaults Restore/load default values for all the setup options. 3.7 Event Logs A built-in event log enables eæier troubleshooting by capturing useful system information. 3.7.1 Change Smbios Event Log Settings Allows you to change the Smbios event log configuration. Smbios Event Log Configuration options: [Disabled] [Enabled] Erase Event Log Allows you to choose options for erasing Smbios Event Log. Configuration options: [No] [Yes, Next reset] [Yes, Every reset] When Log is Full Allows you to choose options for reactions to a full Smbios Event Log. Configuration options: [Do Nothing] [Erase Immediately] Log System Boot Event Allows you to enbale or disable logging of the system boot event. Configuration options: [Enabled] [Disabled] MECI Configuration options: [1] – [255] METW Configuration options: [0] – [99] Log EFI Status Code Configuration options: [Disabled] [Enabled] Convert EFI Status Codes to Standard Smbios Type Configuration options: [Disabled] [Enabled] Chapter 3: BIOS setup 3-19

****** Page 54 ****** 3.7.2 View Smbios Event Log Allows you to view all the events in the Smbios event logs. 3-20 1-13101-IM-B

****** Page 55 ****** Appendix Notices FCC Compliance Information Responsible Party: Asus Computer International Address: 48720 Kato Rd., Fremont, CA 94538, USA Phone/ Fax No: (510)739-3777 / (510)608-4555 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. Appendix

****** Page 56 ****** Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1 ) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAN Déclaration de conformité de Innovation, Sciences et Développement économique Canada (ISED) Le présent appareil est conforme aux CNR djlnnovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1 ) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de rappareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage est susceptible d’en compromettre le fonctionnement. CAN VCCI: Japan Compliance Statement Class B ITE VCCI—B KC: Korea Warning Statement B? 7171 01 7} Q 1-13101-IM-B

****** Page 57 ****** REACH Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at csr.asus.com/english/REACH.htm. DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products. DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste. ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutiorE for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to httpd!cscasus.com/engljshffak—khtm for detailed recycling information in different regions. Regional notice for California WARNING Cancer and Reproductive Harm – P65Warnings.ca.gov GoogleTM License Terms Copyright@ 2020 Google Inc. All Rights Reserved. Licensed under the Apache License, Version 2.0 (the “License”); you may not use this file except in compliance with the License. You may obtain a copy of the License at: apache.org/licenses/LlCENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KINDJ either express or implied See the License for the specific language governing permissions and limitations under the License. Appendix

****** Page 58 ****** English ASUSTeKComputer Inc. hereby declares that this device is in compliance with the essential requirements ard other provisions of related Directives. Full text of EU declaration of conformity is available at: asus.com/support Fransais AsusTekComputer Inc. déclare par la présente que cet appareil est conforme aux critéres essentiels et autres clauses pertinentes des directives concernées. La déclaration de conformité de [‘UE peut étre téléchargée partir du site Internet suivant asus.com/s,L11wi Deutsch ASUSTeK Computer Inc. erklärt hiermit, dass dieses Gerät mit den wesentlichen Anforderungen und anderen relevanten Bestimmungen der zugehörigen Richtlinien übereinstirnrnt. Der gesamte Text der EU- Konformitätserklärung iSt verfügbar untec Italiano ASUSTeK Computer lnc- con la presente dichiara Che questo dispositivoé conforme ai requisiti essenziali e alle altre dispositioni pertinenti con le direttive correlate, II testo completo della dichiarazione di conformitå IJE é disponibile alltndirizzo: asusxom/suppprt Kourm•ül.q ASUS no yczpoicno coo-rzerczzyer OCEOEENI ap•yT’Eü1 COOTETCTEP01.4HM cooneTCIFYF011.[.HX axipexrzz. Iloap06EY.n rwxæryäc•ra: cucrrpyrre Ha asus.com/support bbarapc„NH C ASLSTeK Computer Inc. tie zosa ycr•poäcno e B c’bctrzercrure cyc cyrqecrzeyytre H zpyryze ea c:Bbpsaærre rexcr Ha gernapaz.ur.qra sa ya EC e Ea azpec: asus.com/support Hrvatskl ASUSTeKComputer Inc. ovjrn iZjavljuje dajeovaj uredaj sukladan s bitnim zahtjevima i ostalim adgovarajuCim odredbama vezanih direktiva. Cijeli tekst EU izjave o sukladnosti dostupan je na: asus.com/support destina Spoletnost ASUSTeKComputer Inc. tfmto prohlasujer 2e toto zatlzenf spl huje zäkladnl p02adavky a dalil ptIsluSnå ustanovenf sm/visejlcfch smérnic. Plné znénf prohläienf o shodé EU je k dispozjci na adrese; esus.qom/swppqrt Dansk ASUSTeKComputer Inc. erklærer herrned, at denne enhed eri overenssternmelse med hovedkravene og andre relevante besternrnelser i de relaterede direktivet- Hele EU-overensstemmelseserklæringen kan findes på: Nederlands ASIJSTéKComputer Inc. verklaart hierbij dat ditapparaat voldoet aan de essentiéle vereisten en andere relevante bepalingen van de verwante richtli]nen. De volledige tekst van de EU-verklaring van conformitelt is beschikbaar op: asus.com/support Eestl Käesolevaga kinnitab ASUSTeK Computer Inc. et see seade vastab asjakohaste direktiivide oluliste nöueteleja teistele asjassepuutuvatele sätetele. EL vastavusdeklaratsiooni täieliktekst on saadaval järgmisel aadressil: asus.com/support Suomi ASUSTeK Computer Inc. ilmoittaa tätenrettä tämä laite on asiaankuuluvjen direktiivien olennaisten vaatimusten ja muiden tätä koskevien 5äädösten mukainen. EU-yhdenmukaisuusjlmoituksen koko teksti on luettavissa osoitteessa; asus.com/suppqrt ME to rrapOv, n AsuSTek Computer lnc- n OUOKEJJO OUPPOPQ(ÜVEtt11 EE- TO asus.corn/suppqrt Magyar Az ASUSTeK Computer Inc. ezennel kijelenti, hogy ezaz eszköz megfelel a kapcsolédö Irånyelvek lényeges követelményeinek és egyéb vonatkozö rendelkezéselnek. Az EU megfelelöségi nyllatkozat teljes szOvege innen Ietölthetå: asus.com/support Latvlskl ASUSTeKComputer Inc. arso pazioo, ka ierice atbilst salstito Direktivu bütiskajåm prasibäm un citiem citiem saistogajiem nosacj]umiem. PIIns ES atbilstibas pazloojuma teksts pieejams Belt: asus.com/support Lletuvlq *ASUSTeK Computer Inc.” Siuo tvirtina, kad Sis Irenginys atitinka pagrindinius reikalavimus ir kitas svarbias susijusiq direktyvq nuostatas.Visq ES atitikties deklaracijos tekstq galima rasti: asusucom/suplxbrj Norsk ASUSTeKComputer Inc. erklærer herved at denne enheten er i sarnsvar med hovedsaklige krav og andre relevante forskrifter i relaterte direktiver, Fullstendig tekst for EU-samsvarserklæringen finnes på.• asus.com/support Polskl FirmaASlJSTéKC0ß1PJter Inc. niniejszym urqdzenie to jest tgt)dne z zasadniczymi wymogami i innyrni wlagciwymi pstanowieniami powiqzanych dyrektyw, Pelny tekst deklaracji zgodnogci UE jest dostqpny pod adresern• wwwrasus.com/suppqt! Portuguås A ASUSTeK Computer Inc. declara que este dispositivoestä em conformidade corn os requisitos essenclais e outras disposl@es relevantes das Diret[vas relacionadas.Texto Integral da declaraqäo da IJE dispontvel asus.com/support Romånå ASUSTeKComputer Inc. declarå cä acestdispozitivseconformeazå cerinielor esentiale $ altor prevederi relevante ale directivelor conexe.Textul complet al declaratiei de conformitate a Uniunii Europene se gåse$e la: asus.com/support srpskl ASUSTeKComputer Inc. ovjm izjavljuje da je ovaj uredaj u saglasnosti sa osnovnjm zahtevima i drugim relevantnim odredbama povezanih Direktiva, Pun tekst EU deklaracije o usaglasenosti je dostupanda adrest esusr.om/suppprt Slovensky Spoloenost ASUSTeK Computer tyrnto vyhlasuje, toto zariadenie vyhovuje zåkladn9rn p02iadavkåm a ostatym prlsluSn9rn ustanoveniarn prisluSnych smern(c. Ce19 text vyhlåsenia 0 zhode pre Ståty EU je dostupn9 na adrese: Slovenstlna ASUSTeKComputer Inc. izjavlja,daje ta naprava skladna z bistvenimi zahtevami in drugimi ustreznirni dolotbarni povezanih direktiv, Celotno besedilo EU•izjave 0 skladnosti je na voljo na spletnem mestu: Iscorn/support Espanol Por la presente ASUSTeKCornputer Inc. declara que este dispos[tlvo cumple los requisitos bäsicos y Otras disposiciones pertinentes de las directivas relacionadas. EI texto completo de Ia declaraclön de la IJE de conformidad esta disponible en: asus.com/support Svenska ASUSTeKComputer Inc. förklarar härmed attdenna enhet överensstämmer med de grundläggande kraven och andra relevanta föreskrifter i relaterade direktiv. Fulltext av EU-försäkran om överensstämmelse finns pä: asus.com/support YepaiHtbKa ASLSTeK Computer Inc. wo gei npucrpli ElA110Et;ae mn:ora.u ra IHI.IIKM Axipexnm rexcr gexaapa41ä crangap-raM €C gocry’11HE•1i Ka : TOrkß AsusTek Computer Inc., bu aygltln ternel gereksinimlerle ve ilißili Yönergelerin diger ilgili k0#Jllaryla uyurnlu Olduounu beyan edet- AB uygunluk bildiriminin tam rrætni adreste bulunabilir: asusxom/suppprt Bosanskl ASUSTeKComputer Inc. ovim izjavl]uje da jeovaj ureda] uskladen sa bitnlrn zaht]evima I ostal[m odgovarajuCim odredbama vezanih direktiva Cijeli tekst EU izjave o uskladenosti dostupan je na: asus.com/support 1-13101-IM-B

****** Page 59 ****** ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax Web site Technical Support Telephone Online support IF. No. 15, Lide Rd.. Beitou Dist., Taipei City 112, Taiwan +886-2-2894-3447 +886-2-2890-7798 httpsdlasus.com +86-21-38429911 qr.asus.com/techserv ASUS COMPUTER INTERNATIONAL (America) Address Telephone Fax Web site Technical Support Support fax Telephone Online support 48720 Kato Rd., Fremont, CA 94538, USA +1-510-739-3777 +1-510-608-4555 asus.com/us/ +1-812-284-0883 +1-812-282-2787 qr.asus.com/techserv ASUS COMPUTER GmbH (Germany and Austria) Address Web site Online contact Technical Support Telephone (DE) Telephone (AT) Online support Appendix Harkortstrasse 21-23. 40880 Ratingen, Germany asus.com/de asus.com/support/Product/ContactUs/ Services/questionform/?lang=de-de +49-2102 5789 557 +43 1360 2775 461 asus.com/de/support


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

ASUSTEK H310I-IM-B (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.