Click here to download ASUS VN279 (01) PDF MANUAL

PDF Content Summary:

****** Page 1 ****** VN279 series LCD Monitor User Guide

****** Page 2 ****** First Edition May 2013 Copyright 0 2013 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”) Product warranty or service will not be extended if: (1) the product is repaired, modified or alered, unless such repair, modification of alteration is authorized in writing byASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND. EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS. LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation nd to the owners’ benefit, without intent to infringe.

****** Page 3 ****** Contents Notices…………………………………………………………………………………………… • Safety information Care & Cleaning vi Takeback Services vii Chapter 1: Product introduction . …. ….. ….. ….. 1-2 1-2 Back view ….. ….. ….. ….. ……………….. . 1-3 1-4 (for VESA wall mount) ….. ….. ….. ….. ………………………………… ….. … 2-2 2-4 . …. …………. 3-5 3-9 1.1 1.2 1.3 Welcome! Package contents Monitor introduction ….. ….. ….. ….. …………………. 1.3.1 1.3.2 1.3.3 Chapter 2: Front view . QuickFit Function Setup 2.1 2.2 2.3 2.4 2.5 2.6 Assembling the monitor arm/base ………… Adjusting the monitor Detaching the arm/base Using the connector cover………………………….. Connecting the cables Turning on the monitor Chapter 3: General instructions 3.1 3.2 3.2 3.3 OSD (On-Screen Display) menu 3.1.1 How to reconfigure 3.1.2 OSD function introduction ….. ….. ….. …. Specifications summary (VN279H)…………………… Specifications summary (VN279Q)…………………………… Troubleshooting (FAQ) 3-10 Supported operating modes iii

****** Page 4 ****** Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment hæ been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reæonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following meæures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. As an Energy Stare Partner, our company hæ determined that this product meets the Energy Star guidelines for energy efficiency. ENERGY STAR Canadian Department of Communications Statement This digital apparatus does not exceed the Clæs B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. This Class B digital apparatus meets all requirements of the Canadian Interference – Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouiller du Canada. iv

****** Page 5 ****** Safety information Before setting up the monitor, carefully read all the documentation that came with the package. To prevent fire or shock hazard, never expose the monitor to rain or moisture. Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury. If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer. Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately. Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over a radiator or heat source unless proper ventilation is provided. The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. Use the appropriate power plug which complies with your local power standard. Do not overload power strips and extention cords. Overloading can result in fire or electric shock. Avoid dustJ humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface. Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges. Never push objects or spill liquid of any kind into the slots on the monitor cabinet. To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC. If you encounter technical problems with the monitor, contact a qualified service technician or your retailer. This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment, and mercury-containing button cell battery) should not be placed in municipal waste. Please check local regulations for disposal of electronic products.

****** Page 6 ****** Care & Cleaning Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor J grasp the edges of the monitor. Do not lift the display by the stand or the cord. Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with mild cleaner. Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the monitor. Never spray cleaner directly on the screem as it may drip inside the monitor and cause an electric shock. The following symptoms are normal with the monitor: The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again to make sure that the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours. When the screen becomes black or flæhes, or cannot work anymore, contact your dealer or service center to fix it. Do not repair the screen by yourself! Conventions used in this guide WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you MUST follow to complete a tæk. NOTE: Tips and additional information to aid in completing a tæk. vi

****** Page 7 ****** Where to find more information Refer to the following sources for additional information and for product and software updates. 1. 2. ASUS websites The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to Optional documentation Your product package may include optional documentation that may have been added by your dealer. These documents are not part of the standard package. Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components well the packaging materials. Pleæe go to csr.æ for detail recycling information in different region. vii

****** Page 8 ****** viii

****** Page 9 ****** 1.1 Welcome! Thank you for purchasing the ASUS@LCD monitor! The latest widescreen LCD monitor from ASUS provides a broader, brighter and crystal-clear display, plus a host of features that enhance your viewing experience. With these features, you can enjoy the convenience and delightful visual experience that the monitor brings to you! 1.2 Package contents Check your package for the following items: LCD monitor Monitor Base Quick start guide Warranty card Power cord VGA cable MHL cable (optional) HDMI cable (optional) HDMI-DVI cable (optional) DisplayPort cable (optional) Audio cable If any of the above items is damaged or missing, contact your retailer immediately. ASUS VN279 Series LCD Monitor 1-1

****** Page 10 ****** 1.3 1.3.1 Monitor introduction O Front view O O MENU O O O O 1. 2. 3. 4. 1-2 @QuickFit Button: • Activates the QuickFit function designed for alignment. The QuickFit function contains 7 pages of common grid patterns, paper sizes, and photo sizes. e / g Button: Use this hotkey to switch from six video preset modes (Scenery, Standard, Theater, Game Night View, and sRGB Mode) with SPLENDIDTM Video Intelligence Technology Exits the OSD menu or goes back to the previous menu when the OSD menu is active. Automatically adjusts the image to its optimized position, clock, and phæe by pressing this Button for 2-4 seconds (for VGA mode only). O/V Button: Decreases values or moves your selection left/down. Volume hotkey. MENU Button: • Turns on the OSD menu. • Enacts the selected OSD menu item. Chapter 1: Product introduction

****** Page 11 ****** 5. 7. Toggles the Key Lock function between on and off with a long press for 5 seconds. Button: Increases values or moves your selection right/up. • Brightness hotkey. -O Input Select Button: Selects an available input source. Press -a Button (Input Select Button) to display VGA, HDMI/MHL-I (VN279H), HDMI/MHL-2 (VN279H), DisplayPort (VN279Q) signals after you connect VGA, HDMI/MHL, or DisplayPort cable with the monitor. d.) Power Button/Power Indicator Turns the monitor ON/OFF. The color definition of the power indicator is the below table. 1.3.2 Status White Amber Off Back view VN279H o Description ON Standby mode OFF HDMI/ HDMI IMHL-2 VGA oo o ooo 1. 2. 3. AC-IN port. This port connects the power cord. DisplayPort. This port is for connection for a DisplayPort compatible device. HDMI/MHL port. This port is for connection with an HDMI/MHL compatible device. ASUS VN279 Series LCD Monitor 1-3

****** Page 12 ****** 4. 5. 6. 7. 8. VGA port. This 1 5-pin port is for PC VGA connection. Audio-in port. This port connects PC audio source by the bundled audio cable. Earphone jack. This port is only available when an HDMI/DisplayPort cable is connected. Kensington lock slot. Control Buttons 1-4 1.3.3 QuickFit Function The QuickFit function contains three kinds of patterns: (1) Grid patterns (2) Paper size (3) Photo size. To activate the patterns, press the QuickFit hotkey. Press the Button again until a desired pattern is selected. 1. Grid patterns The grid patterns facilitate designers and users to organize content and layout on a page and achieve a consistent look and feel. Alignment Grid Alig ment Grid 2. Paper size QuickFit provides numerous commonly used standard paper sizes for users to view their documents in real size on the screen. Letter Letter Chapter 1: Product introduction

****** Page 13 ****** 3. Photo size The various real photo sizes displayed in the QuickFit function provides photographers and other users to accurately view and edit their photos in real size on the screen. Photo 4×6, 3×5, 2×2 x Photo 8×10, 5×7 8×10 5×7 When QuickFit is activated, press the control Buttons to make adjustments. The QuickFit OSD displayed in the lower right corner of the screen will guide users to make selections. EXIT QuickFit The QuickFit OSD shown on the screen is not accessible by tapping on it. ASUS VN279 Series LCD Monitor 1-5

****** Page 14 ****** 1-6 Chapter 1: Product introduction

****** Page 15 ****** 2.1 Assembling the monitor arm/base To æsemble the monitor base: Have the front of the monitor face down on a table. 2. Attach the base into the armJ making sure the tab on the arm fits into the groove on the base. 3. Fix the base to the arm by fætening the bundled screw. We recommend that you cover the table surface with soft cloth to prevent damage to the monitor. D 2.2 Adjusting the monitor For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you. Hold the stand to prevent the monitor from falling when you change its angle. The recommended adjusting angle is +22 to -59. -50 to +220 It is normal that the monitor slightly shakes while you adjust the viewing angle. ASUS VN279 Series LCD Monitor 2-1

****** Page 16 ****** 2.3 Detaching the arm/base (for VESA wall mount) The detachable arm/bæe of this monitor is specially designed for VESA wall mount. To detach the arm/base: 1. 2. 3. 4. 5. Have the front of the monitor face down on a table. Remove the rubbers in the four screw holes. (Figure 1) Remove the base (Figure 2). Pry the rear hinge cover (Figure 3). Use a screwdriver to remove the four screws on the hinge (Figure 4), then remove the hinge. Fi ure 1 Figure 3 Fi ure 2 Figure 4 2-2 We recommend that you cover the table surface with soft cloth to prevent damage to the monitor. Hold the stand while removing the screws. The VESA wall mount kit (100 x 100 mm) is purchased separately. Use only the UL Listed Wall Mount Bracket with minimum weight/load 22.7kg (Screw size: M4 x 10 mm) Chapter 2: Setup

****** Page 17 ****** 2.4 Using the connector cover To remove the connector cover: a. Pull the connector cover downwards. b. Lift the connector cover form its center. To assemble the connector cover: a. Insert the 2 tabs on both sides of the cover into the monitor. b. Push the connector cover up to its original position. 2.5 Connecting the cables 1. Connect the cables as the following instructions: VN279H HDMI /MHL.I HDMI/ MHL.2 VN279Q DisplayPort AC-IN HDMI MHL HDMI VGA VGA VGA Earphone jack Audio-in To connect the power cord: connect one end of the power cord securely to the monitor’ AC input port, the other end to a power outlet. ASUS VN279 Series LCD Monitor 2-3

****** Page 18 ****** 2-4 To connect the VGA/HDMI (MHL)/DisplayPort cable: a. Plug one end of the VGA/HDMI (MHL)/DisplayPort cable to the monitor’s VGA/HDMI (MHL)/DisplayPort jack. b. Connect the other end of the VGA/HDMI (MHL)/DisplayPort cable to your computer or mobile device’s VGA/HDMI (MHL)/DisplayPort jack. c. Tighten the two screws to secure the VGA connector. To connect the audio cable: connect one end of the audio cable to the monitor’s Audio-in port, the other end to the computer’s audio-out port. To use the earphone: connect the end with plug type to the monitor’s earphone jack when an HDMI or DisplayPort signal is fed. When these cables are connected, you can choose the desired signal from the Input Select item in the OSD menu. 2.6 Turning on the monitor Press the power button d) . See page 1-2 for the location of the power button. The power indicator (b lights up in white to show that the monitor is ON. Chapter 2: Setup

****** Page 19 ****** ASUS VN279 Series LCD Monitor 2-5

****** Page 20 ****** 2-6 Chapter 2: Setup

****** Page 21 ****** 3.1 3.1.1 color OSD (On-Screen Display) menu How to reconfigure Press the MENU Button to activate the OSD menu. 2. Press O/ V and to navigate through the functions. Highlight the desired function and press the MENU Button to activate vrvz Spl d Select System Setup Theater Mode Night it. If the function selected hæ asub-menu, press O/ V and •Ä/A again to navigate through the sub-menu functions. Highlight the desired sub-menu function and press the MENU Button to activate it. 3. Press O/ V and to change the settings of the selected function. 4. To exit and save the OSD menu, press the / Button repeatedly until the OSD menu disappears. To adjust other functions, repeat steps 1-3. 3.1.2 OSD function introduction 1. Splendid This function contains six sub- functions you can select for your preference. Each mode has the Reset selection allowing you to maintain your setting or return to the preset mode. VN7 COIor 1 Mode Game Mode Night. View Mo•de Irun..rt Select Mode system setuo Menu Scenery Mode: best choice for scenery photo display with SPLENDIDTM Video Enhancement. Standard Mode: best choice for document editing with SPLENDIDTM Video Enhancement. Theater Mode: best choice for movies with SPLENDIDTM Video Enhancement. Game Mode: best choice for games playing with SPLENDIDTM Video Enhancement. Night View Mode: best choice for dark-scene games or movies with SPLENDIDTM Video Enhancement. sRGB: best choice for viewing photos and graphics from PCs. In the Standard Mode, the ASCR, Saturation ,Sharpness functions and Skin Tone are not user-configurable. In the sRGB Mode, the Saturation, Color Tempo Skin Tone, Sharpness, Brightness, Contrast and ASCR functions are not user- configurable. ASUS VN279 LCD Monitor 3-1

****** Page 22 ****** 2. 3. 3-2 Color You can adjust Brightness, SOIenOd color Contrast, Saturation, Color Temp. and Skin Tone from this menu. Input Select Brightness: the adjusting range is from 0 to 100. C’*ttrast Sat.wat:ion Ccdcw- V ernp. User Mode is a hotkey to activate System Setup this function. Contrast: the adjusting range is from 0 to 100. Saturation: the adjusting range is from 0 to 100. Color Temp.: contains four modes including Cool, Normal, Warm, and User Mode. Skin Tone: contains three color modes including Reddish, Natural, and Yellowish. In the User mode, colors of R (Red), G (Green), and B (Blue) are user- configurable; the adjusting range is from 0-100. Image You can adjust Sharpness, Trace Free, Aspect Control, VividPixeli ASCR, Position (VGA only) and Focus (VGA only) from this menu. Sharpness the adjusting range is from 0 to 100. Trace Free: adjusts the response time of the monitor. VN279 Sharpness Traca: Free Aspect Control ASCR Input Select System Setup Move so 60 Aspect Control: adjusts the æpect ratio to Full’] “4:30 or ttOverScan” (only available for the HDMI input). VividPixel: enhances the outline of the displayed picture and generates high-quality images on screen. ASCR: turns on/off the ASCR (ASUS Smart Contrast Ratio) function. Position (Only available for VGA input): adjusts the horizontal position (H-Position) and the vertical position (V-Position) of the image. The adjusting range is from 0 to 100. Focus (Only available for VGA input): reduces Horizonal-line noise and Vertical-line noise of the image by adjusting (Phase) and (Clock) separately. The adjusting range is from 0 to 100. • Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows horizontal disturbances. Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the image is not proportional. Chapter 3: General Instructions

****** Page 23 ****** 4. 5. Input Select In this function, you can select your desired input source. GamePlus The GamePlus Function provides a toolkit and creates a better gaming environment for users when playing different types of games. In addition, Aimpoint function is specially designed for new gamers or beginners interested in First Person Shooter (FPS) games. VN279 VGA HOMI/’+/L Ilvut Sekct system setup VGA color Irvut Select system setup VN279 Input Select Gan’i*Ph.i8 System Setup Move (VN279Q) (VN279H) Press O/ V and to select between Aimpoint and Timer function. Press MENU to confirm the function you choose, and — / to go back, off, and exit. ASUS VN279 LCD Monitor 3-3

****** Page 24 ****** GamePlus — Aimpoint 6. 3-4 GamePlus Main Menu g : Exit ‘Off : Select GamePlus — Timer 3Ü:ÜÜ : Exit/ Off Select System Setup Allows you to adjust the system. Splendid Demo Mode: splits the screen into two for Splendid modes comparison. Volume: the adjusting range is from 0 to 100. ECO Mode: reduces power consumption. OSD setup: o o GamePlus — Timer — Position : ivit / Off VN279 Splendid color input Select GamcPlus System Setup Splendid Oerno Mode Volume Mode key lock Information Language All Reset Move s 48 Exit English Adjusts the horizontal position (H-Position)/the vertical position (V-Position) of the OSD from 0 to 100. Adjusts the OSD timeout from 10 to 120 seconds. Enables or disables the DDC/CI function. Adjusts the OSD background from opaque to transparent. Keylock: enables the key lock function. A long press for 5 seconds on the MENU Button to disable the key lock function. Information: shows the monitor information. Language: there are 21 languages for your selection, including English, French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech, Croatia, Polish, Romanian, Hungarian, Turkey, Simplified Chinese, Traditional Chinese Japanese, Korean, Thai, Indonesia, Persian. All Reset: “Yes” allows you to restore the default settings. Chapter 3: General Instructions

****** Page 25 ****** 3.2 Specifications summary (VN279H) Panel Type Panel size Max. Resolution Pixel pitch Brightness (Typical) Contrast Ratio (Typical) Contrast Ratio (Max.) Viewing angle(H/V) CR>IO Display colors Response time SPLENDIDTM Video Enhancement SPLENDIDTM selection Auto adjustment Color temperature selection Analog input Digital input Earphone jack Colors Speaker (Built-in) Power LED Tilt lock Voltage rating Power consumption Temperature (Operating) Temperature (Non-operating) Weight (Esti.) Multi-languages Accessories ASUS VN279 LCD Monitor TFT LCD 27″W (16:9, 68.6 cm) wide screen 1920 x 1080 0.311 mm 300 cd/m2 3000: 1 (with ASCR on) 17871780 16.7 M 5 ms (Gray to gray) Yes 6 video preset modes (by hotkey) Yes 4 color temperatures D-sub HDMI VI .4 (MHL) Yes Black 2 Stereo, RMS White (On)/Amber (Standby) +229- -59 Yes AC: 100-240V Power On: < 35 W Standby: IO Display colors Response time SPLENDIDTM Video Enhancement SPLENDIDTM selection Auto adjustment Color temperature selection Analog input Digital input Earphone jack Colors Speaker (Built-in) Power LED Tilt lock Voltage rating Power consumption Temperature (Operating) Temperature (Non-operating) Weight (Esti.) Multi-languages Accessories ASUS VN279 LCD Monitor TFT LCD 27″W (16:9, 68.6 cm) wide screen 1920 x 1080 0.311 mm 300 cd/m2 3000: 1 (with ASCR on) 17871780 16.7 M 5 ms (Gray to gray) Yes 6 video preset modes (by hotkey) Yes 4 color temperatures D-sub HDMI VI .4 (MHL)I DisplayPort Yes Black 2 Stereo, RMS White (On)/Amber (Standby) +229- -59 Yes AC: 100-240V Power On: < 35 W Standby: < 0.5 W (Typical), Power Off: 0.3 W (Switch off) ooc-40•c -20gc-+60gc 619.2 mm x 440.4 mm x 209.8 mm (machine) 706 mm x 536 mm x 188 mm (package) 4.8 kg (Net); 7.5 kg (Gross) 21 languages (English, French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech, Croatia, Polish, Romanian, Hungarian, Turkey, Simplified Chinese, Traditional Chinese, Japanese, Korean, Thai, Indonesia, Persian) VGA cable, MHL cable (optional), HDMI-DVI cable (optional), HDMI cable (optional), DP cable (optional), Audio cable, Power cord, Quick start guide, Warranty card 3-7 ****** Page 28 ****** Regulation approvals Energy Stare, China Energy Level 1, UL/cULj CE, Erp, FCC (Class B), CCC, BSMI, CU, C-TickJ VCCI, UkrSEPRO, TC06.OJ ISO 9241 307, J-MOSS, ROHS, WEEE, PSE, WHQL for Windows 7 and Windows 8 *Without audio and USB hub connection. **Specifications are subject to change without notice. 3-8 Chapter 3: General Instructions ****** Page 29 ****** 3.3 Troubleshooting (FAQ) Problem Power LED is not ON The power LED lights amber and there is no screen image Screen image is too light or dark Screen image is not centered or sized properly Screen image bounces or a wave pattern is • present in the image Screen image has color defects (white does • not look white) Screen image is blurry or fuzzy No sound or sound is low ASUS VN279 LCD Monitor Possible Solution Press the e.) Button to check if the monitor is in the ON mode. Check if the power cord is properly connected to the monitor and the power outlet. Check if the monitor and the computer are in the ON mode. Make sure the signal cable is properly connected the monitor and the computer. Inspect the signal cable and make sure none of the pins are bent. Connect the computer with another available monitor to check if the computer is properly working. Adjust the Contrast and Brightness settings via OSD. Press the g / Button for 2-4 seconds to automatically adjust the image (for VGA mode only). Adjust the H-Position or V-Position settings via OSD. Make sure the signal cable is properly connected to the monitor and the computer. Move electrical devices that may cause electrical interference. Inspect the signal cable and make sure that none of the pins are bent. Perform All Reset via OSD. Adjust the R/G/B color settings or select the Color Temperature via OSD. Press the g / g Button for 2-4 seconds to automatically adjust the image (for VGA mode only). Adjust the Phase and Clock settings via OSD. Ensure that the HDMI cable is properly connected to the monitor and the computer. Adjust the volume settings of both your monitor and HDMI device. Ensure that the computer sound card driver is ro erl installed and activated. 3-9 ****** Page 30 ****** 3.4 Supported operating modes Resolution Frequency 1024×768 1024×768 1024×768 1 152×864 1280×720 1280×768 1280×800 1280×960 1280×1024 1280×1024 1360×768 1366×768 1440×900 1600×1200 1680×1050 1920×1080 (Primary) Horizontal Frequency (KHz) 31.5 35.0 37.9 37.5 31.5 35.16 37.9 48.1 46.9 49.7 48.4 56.5 60.0 67.5 45 47.78 49.7 60.0 63.4 79.97 47.71 47.71 55.94 75.0 65.3 67.5 Vertical Frequency Pixel (MHz) (Hz) 60 67 72 75 70 56 60 72 75 75 60 70 75 75 60 60 60 60 60 75 60 60 60 60 60 60 25.18 30.24 31.50 31.50 28.32 36.00 40.00 66.75 49.50 57.28 65.00 75.00 78.50 108.00 75.25 79.50 83.50 108.00 108.00 135.00 85.50 85.50 106.50 162.00 146.25 148.50 * Modes not listed in the table may not be supported. For optimal resolution, we recommend that you choose a mode listed in the table above. * This monitor supports full HD (480p, 576p, 720p, 1080i/p) video content from game consoles, DVD players and other consumer video devices via HDMI. 3-10 Chapter 3: General Instructions








Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.