ARUBA CAMPUS AP-504 (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD ARUBA CAMPUS AP-504 (01) PDF MANUAL


PDF Content Summary: Aruba 500 Series Campus Access Points Installation Guide The Aruba 500 Series campus access points (AP-504 and AP-505) are high-performance, dual-radio wireless devices that can be deployed in either controller-based (ArubaOS) or controllerless (Aruba Instant) network environments. These access points deliver high performance concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi functionality with MIMO radios (2x2 in 2.4 GHz, 2x2 in 5 GHz), while also supporting legacy 802.11a/b/g/n/ac wireless services. In addition to both Wi-Fi radios, these APs also incorporate a Bluetooth Low Energy (BLE) and Zigbee radio, supporting a variety of use-cases and services, such as locationing and IoT. A mount kit (sold separately) is needed to mount the AP. Make sure to purchase the correct mount kit for the intended deployment of the AP. Package Contents ● Aruba 500 Series access point (with a pre-installed mount bracket) The AP mount bracket attaches to a variety of mount kits (sold separately). Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Hardware Overview The following sections outline the hardware components of the 500 Series access points. Figure 1 AP-505 Front View Rev01 | July 2019 1 Figure 2 AP-504 Front View External Antenna Connectors The AP-504 access points are equipped with two external antenna connectors located on the front corners of the access point (see Figure 2). Antenna ports A0 and A1(corresponding with radio chain 0 and 1), are used for both radios and bands (RF signals are diplexed). ! External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other Aruba-certified technician, using manufacturer-approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are required to record the antenna gain for this device in the system management software. A list of approved antennas can be found at: arubanetworks.com/assets/og/OG_AP-500Series.pdf. Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba (ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant. Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine. Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système. Une liste d'antennes approuvées peut être trouvée à arubanetworks.com/assets/og/OG_AP- 500Series.pdf. 2 Aruba 500 Series Campus Access Points | Installation Guide Figure 3 LEDs (AP-505 shown) LEDs System Status The System Status LED indicates the operating condition of the access point. Table 1 System Status LED Color/State Meaning Off Device Powered off Green- solid Device ready, fully functional, no network restrictions

Green- blinking 1 Device booting, not ready Green- flashing off 2 Device ready, fully functional, uplink negotiated in sub-optimal speed (<1Gbps) Green- flashing on 3 Device in deep-sleep mode

Amber- solid Device ready, restricted power mode (IPM restrictions applied), no network restrictions Amber- flashing off Device in sub-optimal ready, restricted speed (<1Gbps) power mode (IPM restrictions applied), uplink negotiated Red System error condition - Immediate action required 1. Blinking: one second on, one second off, 2 seconds cycle. 2. Flashing off: mostly on, fraction of a second off, 2 seconds cycle. 3. Flashing on: mostly off, fraction of a second on, 2 seconds cycle. Radio Status The Radio Status LED indicates the operating mode of the access point’s radios. Table 2 Radio Status LEDs Color/State Meaning Off Device powered off, or both radios disabled Green- solid Both radios enabled in access mode Green- blinking One radio enabled in access mode, other disabled Amber- solid Both radios enabled in monitor mode Aruba 500 Series Campus Access Points | Installation Guide 3 Color/State Meaning Amber- blinking One radio enabled in monitor mode, other disabled Green/Amber- alternating1 Green: one radio in access mode Amber: one radio in monitor mode 1. Alternating: one second each color, 2 seconds cycle. LED Display Settings The LEDs have three operating modes that can be selected in the system management software: ● Normal mode: Refer to Table 1and Table 2 ● Off mode: LEDs are off ● Blink mode: LEDs blink green (synchronized) Figure 4 AP-505 Rear View Reset Button USB 2.0 Interface DC Power Interface Console Interface Kensington Lock Slot E0 Cable Guide The cable guide on the rear of the access point is used to organize cables, as shown in Figure 5. The use of the cable guide is optional and does not support all types of cables and plugs. 4 Aruba 500 Series Campus Access Points | Installation Guide Figure 5 Cable Guide Bluetooth Low Energy and Zigbee Radio 500 Series access points are equipped with an integrated BLE and Zigbee radio that provide the following capabilities: ● location beacon applications ● wireless console access ● IOT gateway applications Console Port The console port is a Micro-B connector located on the back of this device. A proprietary serial adapter cable (AP- CBL-SERU) is needed to use this interface. It is sold separately to connect the AP to a serial terminal or a laptop for direct local management (a standard USB cable cannot be used for this interface). Ethernet Port The Aruba 500 Series is equipped with a 10/100/1000Base-T auto-sensing MDI/MDX Ethernet port (E0). This E0 port supports IEEE 802.3af and 802.3at Power over Ethernet compliance, accepting power from a Power Sourcing Equipment (PSE) such as a PoE midspan injector, or network infrastructure that support PoE. Kensington Lock Slot The 500 Series is equipped with a Kensington lock slot for additional physical security. USB 2.0 Interface The top of this access point is equipped with a USB-A port that is compatible with selected cellular modems and other peripherals. When active, this port can supply up to 5W/1A to a connected device. Reset Button The reset button located on the back of the device can be used to reset the access point to factory default settings or turn off/on the LED display. There are two ways to reset the access point to factory default settings: Reset the AP during normal operation press and hold down the reset button using a small, narrow object such as a paper clip for more than 10 Aruba 500 Series Campus Access Points | Installation Guide 5

seconds during normal operation. Reset the AP while powering up 1. Press and hold down the reset button using a small, narrow object such as a paper clip while the access point is not powered on (either via DC power or PoE). 2. Connect the power supply (DC or PoE) to the access point while the reset button is being held down. 3. Release the reset button on the access point after 15 seconds. To turn off/on the LED display, press and release the reset button using a small, narrow object, such as a paperclip for less than 10 seconds during normal operation of the access point. Power E0 port supports PoE-in (AP is a PoE-PD device), allowing the device to draw power from compliant PoE power sources. If PoE is not available, a proprietary AP-AC-12V30B power adapter (sold separately) can be used to power the access point. When both PoE and DC power sources are available, the DC power source takes precedence. In that case, the access point simultaneously draws a minimal current from the PoE source. In the event that the DC source fails, the access point switches to the PoE sources. The Intelligent Power Monitoring (IPM) feature may also be used to manage the power consumption preferences for this device. When enabled, the user may enable/disable power restrictions for the access point using Aruba’s AP management software. Table 3 lists operational restrictions when the access point is powered by different power options. Table 3 Power Options and Operational Restrictions Power Source IPM Restrictions DC power n/a No restrictions, all capabilities available PoE 802.3at n/a No restrictions, all capabilities available PoE 802.3af enabled All configuration) capabilities available (features may be disabled per IPM PoE 802.3af disabled USB disabled The 500 Series access points support a deep-sleep mode to deliver significant power and cost savings. Before You Begin Refer to the sections below before beginning the installation process. ! FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).

Pre-Installation Checklist Before installing your Aruba 500 Series access point, be sure that you have the following (not included with the AP): ● A mount kit compatible with the AP and mount surface ● Cat5E or better UTP cable with network access ● One or more external antennas (when using the AP-504) ● (Optional) a compatible 12V AC-to-DC power adapter with power cord ● (Optional) a compatible PoE midspan injector with power cord ● (Optional) a compatible snap-on front cover (for easy aesthetic customization) ● (Optional) an AP-CBL-SERU console cable Also make sure that (at least) one of the following network services is supported: 6 Aruba 500 Series Campus Access Points | Installation Guide ● Aruba Discovery Protocol (ADP) ● DNS server with an “A” record ● DHCP Server with vendor-specific options The Aruba 500 Series access point is designed in compliance with governmental requirements so that only authorized network administrators can change the settings. For more information about access point configuration, refer to the AP Software Quick Start Guide. Identifying Specific Installation Locations Use the access point placement map generated by Aruba RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/ interference sources will impact RF propagation and should be accounted for during the planning phase and adjusted for in RF plan. ! Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally. Identifying Known RF Absorbers/Reflectors/Interference Sources Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. RF absorbers include: ● Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals. ● Natural Items—Fish tanks, water fountains, ponds, and trees ● Brick RF reflectors include: ● Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets. ● Do not place an access point between two air conditioning/heating ducts. Make sure that access points are placed below ducts to avoid RF disturbances. RF interference sources include: ● Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones) ● Cordless headset such as those used in call centers or lunch rooms ! Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the performance of this equipment could result. ! Access Point Installation the Aruba 500 Series access points are designed for ceiling or wall mounted deployments. Several optional RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches (35cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Déclaration sur les limites d'exposition aux radiofréquences : cet équipement est conforme aux limites d'exposition aux rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance minimale de 35 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs. Aruba 500 Series Campus Access Points | Installation Guide 7 mount kits are available to attach the Aruba 500 Series access point to a variety of surfaces. These mount kits are available as accessories and must be ordered separately. Refer to the online ordering guide at arubanetworks.com/assets/og/OG_AP-500Series.pdf All Aruba access points should be professionally installed by an Aruba-Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Failure to properly install this product may result in physical injury and/or damage to property. ! Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures corporelles et / ou des dommages matériels. ! The installer is responsible for securing the access point onto the ceiling tile rail. Failure to properly install this product may result in physical injury and/or damage to property. ! Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and result in improper operation. Software For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick Start Guide. ! Aruba access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their country’s regulations. For a complete list of approved channels in your country, refer to the Aruba Downloadable Regulatory Table at support.arubanetworks.com. Verifying Post-Installation Connectivity The integrated LED on the access point can be used to verify that the access point access point is receiving power and initializing successfully (see Table 1-Table 2). Refer to the AP Software Quick Start Guide for further details on verifying post-installation network connectivity. Electrical and Environmental Specifications For additional specifications on this product, please refer to the product data sheet at arubanetworks.com Electrical ● Ethernet: ∎ E0 port: 10/100/1000BaseT auto-sensing MDI/MDX wired RJ45 network connectivity port ● Power: ∎ 12V DC power interface, support powering through AC-to-DC power adapter (AP-AC-12V30B) ∎ Power over Ethernet (PoE): 802.3af or 802.3at compliant source If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an output rated 12V DC, minimum 0.75A, marked “LPS” and “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada. Environmental ● Operating: 8 Aruba 500 Series Campus Access Points | Installation Guide ∎ Temperature: 0°C to +50°C (+32°F to +122°F) ∎ Humidity: 5% to 93% non-condensing ● Storage and transport: ∎ Temperature: -40°C to +70°C (-40°F to +158°F) ∎ Humidity: 5% to 93% non-condensing ! The Aruba 500 Series access points are for indoor use only. The access point, AC adapter, and all connected cables are not designed for outdoor use. ! This device is intended for stationary use in partly temperature controlled weather-protected environments. Regulatory Model Name The following regulatory model numbers (RMN) apply to the 500 Series: ● AP-504 RMN: APIN0504 ● AP-505 RMN: APIN0505 Safety and Regulatory Compliance ! RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 13.78 inches (35cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Déclaration de la concernant l’exposition aux rayonnements à fréquence radioélectrique (FR): Cet ! appareil est conforme aux limites d’exposition aux rayonnements FR établies. Il doit être installé et utilisé à une distance minimale de 35 cm (13,78 pouces) entre le radiateur et votre corps, qu’il opère sur la bande 2,4 GHz ou 5 GHz. Cet émetteur ne doit pas être installé ou utilisé à proximité immédiate d’une autre antenne ni d’un autre transmetteur. ! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. ! Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité est susceptible d'annuler son droit d'utilisation. Federal Communication Commission This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. Aruba 500 Series Campus Access Points | Installation Guide 9 ● Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio or TV technician for help. Industry Canada This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations. In accordance with Industry Canada regulations, this radio transmitter and receiver may only be used with an antenna, the maximum type and gain of which must be approved by Industry Canada. To reduce potential radio interference, the type of antenna and its gain shall be chosen so that the equivalent isotropic radiated power (EIRP) does not exceed the values necessary for effective communication. This device complies with Industry Canada's license-exempt RSS regulations. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Déclaration d’Industrie Canada Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une communication efficace. Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement. En cas d'utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé en intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même canal. Canadian Caution This radio transmitter model APIN0504/APIN0505 has been approved by Industry Canada to operate with the antenna types listed in the table in the online ordering guide (link provided below) with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. arubanetworks.com/assets/og/OG_AP-500Series.pdf Le présent transmetteur radio modèle APIN0504/APIN0505 a été approuvé par Industrie Canada pour fonctionner avec les types d'antennes indiqués dans le tableau du guide de commande en ligne (lien fourni ci- dessous) avec le gain permissible maximum indiqué. Il est strictement défendu d'utiliser avec cet appareil les types d'antennes non inclus dans cette liste, ayant un gain supérieur au gain maximum indiqué pour ce type. arubanetworks.com/assets/og/OG_AP-500Series.pdf European Union Regulatory Conformance The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU is available for viewing at: hpe.com/eu/certificates. Select the document that corresponds to your device’s model number as it is indicated on the product label This radio transmitter model has been approved to operate with the antenna types listed in the online ordering guide (link provided below) with the maximum permissible gain indicated. Antenna types not included in this list, having a greater gain than the maximum gain indicated for the type, are strictly prohibited for use with this device. Compliance is only assured if the Aruba approved accessories as listed in the ordering guide are used. arubanetworks.com/assets/og/OG_AP-500Series.pdf Wireless Channel Restrictions 5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia 10 Aruba 500 Series Campus Access Points | Installation Guide (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK). Radio Frequency Range MHz Max EIRP BLE/Zigbee 2402-2480 9 dBm Wi-Fi Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Aruba approval. Brazil Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. 2412-2472 20 dBm 5150-5250 23 dBm 5250-5350 23 dBm 5470-5725 30 dBm 5725-5850 14 dBm ! Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/ Instant User Guide for details on restrictions. This device is intended for indoor use in professional healthcare facilities. This device has no IEC/EN60601-1-2 essential performance. ! Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally. Compliance is based on the use of Aruba approved accessories. Refer to the ordering guide for this access point at arubanetworks.com/assets/og/OG_AP-500Series.pdf. ! Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and result in improper operation. ! Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the performance of this equipment could result. Aruba 500 Series Campus Access Points | Installation Guide 11 Japan México La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. Este equipo ha sido diseñado para operar con las antenas que enseguida se enlistan, en los puntos 3 de: https:/ / arubanetworks.com/assets/og/OG_AP-500Series.pdf y para una ganancia máxima de antena de 7.5 dBi. El uso con este equipo de antenas no incluidas en esta lista o que tengan una ganancia mayor que 7.5 dBi quedan prohibidas. La impedancia requerida de la antena es de 50 ohms. Morocco Нормативные требования Евразийского Экономического Союза Russia HPE Russia: ООО "Хьюлетт Паккард Энтерпрайз" Российская Федерация, 125171, г. Москва, Ленинградское шоссе, 16А, стр.3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677 'HPE Kazakhstan': TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г. Алматы, Бостандыкский район, проспект Аль-Фараби, 77/7, Телефон/факс: + 7 727 355 35 50 Kazakhstan ЖШС "Хьюлетт Паккард Энтерпрайз" Ресей Федерациясы, 125171, Мәскеу, Ленинград тас жолы, 16A блок 3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677 ЖШС «Хьюлетт-Паккард (К)», Қазақстан Республикасы, 050040, Алматы к., Бостандык ауданы, Әл-Фараби даңғ ылы, 77/7, Телефон/факс: +7 (727) 355 35 50 Taiwan 第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功 能。第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使 用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電 機設備之干擾。 12 Aruba 500 Series Campus Access Points | Installation Guide Contact Aruba Main Site arubanetworks.com Support Site support.arubanetworks.com Airheads Social Forums and Knowledge Base community.arubanetworks.com/ North America Telephone 1-800-943-4526 1-408-754-1200 International Telephone arubanetworks.com/support-services/contact-support/ Software Licensing Site hpe.com/networking/support End-of-Life Information arubanetworks.com/support-services/end-of-life/ Security Incident Response Team (SIRT) arubanetworks.com/support-service/security-bulletins/ Email: aruba-sirt@hpe.com Copyright © Copyright 2019 Hewlett Packard Enterprise Development LP Open Source Code This product includes code licensed under the GNU General PublicLicense, the GNU Lesser General Public License, and/or certain other open source licenses. A complete machine-readable copy of the source code corresponding to such code is available upon request. This offer is valid to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to: Hewlett Packard Enterprise Company Attn: General Counsel 6280 America Center Drive San Jose, CA 94089 USAWarranty This hardware product is protected by an Aruba warranty. For more details, visit hpe.com/us/en/support.html Aruba 500 Series Campus Access Points | Installation Guide 13


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply