Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** ana Installation clearances: Electric Dryer PRODUCT MODEL NUMBERS NED4600Y, NED4700Y, NED4655E, NED4705E Minimum spacing for recessed area or closet installation The location must be large enough to allow the dryer door to open fully. Dryer Dimensions 433/811 (1102 mm) (660 mm) 433/ (1102 mm) *273/4 (705 mm) 223/ (578 mm) (1102 mm) *273/411 (705 mm) 223/ II (578 mm) 433/811 (1102 mm) *273/4 (705 mm 223/4″ (578 mm) (737 mm) 133/411 (349 mm) 2911 (737 mm) (457 mm) Minimum Required Spacing 14″ max.* (S 48in.& (310cmf (’55 cm)2 2911 (737 mm) .e-—-— 2911 (737 mm) c (25mm) (737 mm) (Emm) æmnMmnrn) (140 mm) A. Recessed area B. Side view – closet or confined area C. Closet door with vents *Additional spacing recommended (76 m) c *Most installations require a minimum 51/2″ (140 mm) clearance behind the dryer for the exhaust vent with elbow. See “Venting Requirements.” Installation spacing for recessed area or closet installation The dimensions shown following are for the minimum spacing allowed. Additional spacing should be considered for ease of installation and servicing. • Additional clearances might be required for wall, door, and floor moldings. Additional spacing of 1 (25 mm) on all sides of the dryer is recommended to reduce noise transfer. For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation opening are acceptable. Companion appliance spacing should also be considered. WI 0514172A 02/2015
****** Page 2 ****** ELECTRICAL REQUIREMENTS To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. VENTING REQUIREMENTS Exhaust venting: Exhaust your dryer to the outside. 4″ (102 mm) diameter vent is required. Rigid or flexible metal exhaust vent must be used. Do not use plastic or metal foil vet. Exhaust hood must be at least 12″ (305 mm) from the ground or any object that may be in the path of the exhaust. The Vent System Chart provides venting requirements that will help achieve best drying performance. Vent System Chart Exhaust hoods: Recommended Styles: Louvered Hood Acceptable Style: Angled Hood Determine vent path: Box Hood Number of 900 turns or elbows O I 2 3 4 Type of vent Rigid metal Rigid metal Rigid metal Rigid metal Rigid metal Box/louvered hoods 64 ft. (20 m) 54 ft. (16.5 m) 44 ft. (13.4 m) 35 ft. (10.7 m) 27 ft. (8.2 m) Angled hoods 58 ft. (17.7 m) 48 ft. (14.6 m) 38 ft. (11.6 m) 29 ft. (8.8 m) 21 ft. (6.4 m) Vent System Chart (Long Vent Models Only) Select route that will provide straightest and most direct path outdoors. Plan installation to use fewest number of elbows and turns. When using elbows or making turns, allow as much room as possible. Bend vent gradually to avoid kinking. Use as few 900 turns as possible. Determine vent length and elbows needed for best drying performance: Use following Vent System Chart to determine type of vent material and hood combinations acceptable to use. NOTE: Do not use vent runs longer than those specified in Vent System Chart. Exhaust systems longer than those specified will: • Shorten life of dryer. Reduce performance, resulting in longer drying times and increased energy usage. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Number of 900 turns or elbows 1 2 3 4 5 Type of vent Rigid metal Rigid metal Rigid metal Rigid metal Rigid metal Rigid metal Box/louvered, or Angled hoods 120 ft. (36.6 m) 110 ft. (33.5 m) 100 ft. (30.5 m) 90 ft. (27.4 m) 80 ft. (24.4 m) 70 ft. (21.3 m) NOTE: Bottom exhaust installations have a 900 turn inside the dryer. To determine maximum exhaust length, add one 900 turn to the chart. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL