ALPINE PWE-V80 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD ALPINE PWE-V80 (01) PDF MANUAL


PDF Content Summary: SPECIFICATION MAX POWER OUTPUT............................................... 160W CROSSOVER .............................................................. 30-160Hz (-12dB/oct) PHASE ......................................................................... 0°,180° INPUT SENSITIVITY 80mV-0.5V (Line Input) 0.9V-6V (Speaker Input) OPERATIONAL VOLTAGE .......................................... DC 14.4V (Operational between: 11~16V) DIMENSIONS .............................................................. 342mmX238mmX80mm WEIGHT....................................................................... 5 Kg SUBWOOFER INSTALLATION 1. Mount the installation bracket onto the bottom of the subwoofer (4 brackets, 4 screws). 8 INCH SUPER COMPACT ACTIVE SUBWOOFER PWE-V80

Subwoofer Installation Place Under the seat Under the seat In the trunk Caution: Subwoofer warms up during continuous usage. Please make sure that it is not covered and the installation place provides free space to the unit. Installation place and method must not damage electrical wirings, gasoline tank and other objects which might cause short circuit, fire, etc. ACCESSORIES Line controller 10P connection couple (Power line, remote start wire, speaker input wire, ground wire) 5M power extension coupler (12AWG) Speaker output wire 2. Fix the brackets on the body of the vehicle (4 brackets, 4 screws). Subwoofer PWE-V80 Brackets and screws Remote start wire Mounting bracket Fixed screw (locking vehicle) Fixed screw (locking body) Instruction Manual

1. CONNECTION 2. ADJUSTMENT

This product cannot be used in cars fitted with a common negative speaker system. To prevent external noise from entering the audio system: Locate the unit and route the leads at least 10 cm away from the car harness. Keep the power lines as far away from other leads as possible. Connect the ground lead securely and safely to a bare metal spot (remove the coating if necessary) of the car chassis. If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine Dealer can provide various noise suppressor solutions, contact them for further information. 1 Disconnect the cable from the negative terminal of the car battery. Your Alpine Dealer knows best about noise prevention measures so consult your dealer for further information. Ensure secure connections. Any unused connections should be insulated with electrical insulation tape. If the on-board computer or similar device, such as the ECU, contains security code, you may loose the memory when connecting the negative lead. CAUTION If there is distortion or you hear a popping sound from the subwoofer, the input level is too high. If the subwoofer has prolonged use in this condition, this may result in deterioration of performance or may cause damage to the subwoofer.

2 Connect CONNECTIONS FOR SPEAKER LEVEL INPUT If your head unit does not have this lead, then please

CONNECTIONS FOR RCA INPUT Head Unit connect to the the ACC lead of the vehicle. The lead that supplies power when the key is at the ACC position. Remote start (blank without) Ground connection Black

L R R R L L e e i i g g f f White t t h h S S t t S S p p e e p p a a e e k k a a e e k k RCA lead (L TYPE) r r e e O O r r O O u u t t u u p p t t u u p p t t u u t t Please connect to either the rear or front speaker output leads. Connect the ground lead securely and safely to a bare metal point on the vehicle chassis. Battery extension lead Yellow POWER INDICATOR Yellow

RCA lead (sold separately) Red R Pre-out L Head Unit - Caution The output of the subwoofer will be affected by the head unit fader settings. White White/black FUSE (10A) Always use the extension cable supplied for connecting the +VE battery terminal. DO NOT connect this lead to the head unit. INPUT GAIN ADJUSTMENT LOW PASS FILTER ADJUSTMENT PHASE SELECTOR Remote start Ground connection Yellow Yellow Black FUSE Blue/White Remote start Connect to the ACC line if the head unit has no remote start lead. Connect the ground lead securely and safely to a bare metal point on the vehicle chassis. Always use the extension Ash Ash/black Left Speaker DO NOT modify this cable. It may cause malfunction and damage to the product 1. Set the gain to MIN, Phase to NORM.LPF to CENTER before swithing on the system. 2. Set the Bass/Treble adjustment to zero on the head unit. Set the volume to your average listening level. lt may help to use a music source that is familiar. 3. Next, gradually increase the gain level and system volume to a

(10V) Battery extension lead cable supplied for connecting the +VE battery terminal. DO NOT connect this lead to the head unit. DO NOT modify this cable. It may cause malfunction and damage to the product Right Speaker point where system balance is achieved. If the gain level is set too high, the subwoofer may begin to distort. Distortion may also occur if the volume is set too high on the head unit. Check that the other speakers have not begun to distort before proceeding with the adjustment. If the entire speaker system in the car is distorting, reduce the volume of the head unit.

Failure to do so may result in fire, accident or electrical shock. POWER SUPPLY & SPEAKER LEVEL INPUT POWER SUPPLY & SPEAKER LEVEL INPUT 4. Once the gain has been set, adjust the L.P.F (Low Pass Filter) at afrequency which compliments your speaker system. (We recommend using CENTER as a starting point.) 5. Adjusting the L.P.F will change the output volume of the

Bolts or nuts used for the brake or steering systems (or any other safety related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire, etc. Remote on subwoofer. Repeat procedures 3 and 4 until the ideal setting is found.

Type of Lead Connect to the remote start lead of the head unit. Additional Information Right speaker Ground wire Power supply 6. The final adjustment is the PHASE of the subwoofer. While sitting in the driver's seat and with music playing, switch to a better setting between NORM and REV - The ideal PHASE

Remote turn on lead Ground lead Power line • If your head unit does not have this lead, then please connect to the the ACC lead of the vehicle. The lead supplies power when the key is in the ACC position. Attach securely and safely to a bare metal spot on the car's chassis. Connect directly to the positive terminal of the car's battery. input Left speaker input setting varies from car to car, depending on the location of the subwoofer and the interior acoustic characteristics of the car.


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply