Free English AIRLIVE 2.5GE XPON ONU (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD AIRLIVE 2.5GE XPON ONU (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What do the panel lights on the AIRLIVE 2.5GE XPON ONU indicate?
The panel lights on your AIRLIVE 2.5GE XPON ONU provide information about the device’s status. The following table explains the meaning of each light:
| LED | Mark | Status | Description |
|---|---|---|---|
| System | SYS | On / Off | System is not running or fatal error. |
| Blink | Normal running. | ||
| Registration | PON | On | The device is registered to the PON system. |
| Off | The device is not registered to the PON system. | ||
| Blink | The device is registering. | ||
| Optical signal loss | LOS | Blink | Device does not receive optical signal. |
| Off | Device receives optical signal. | ||
| LAN | LAN1 LAN2 | On | Port is connected properly. |
| Off | Port connection exception or not connected. | ||
| Blink | Port is sending or/and receiving data. |
What are the functions of the ports and buttons on the interface panel of the AIRLIVE 2.5GE XPON ONU?
The interface panel on the back of the AIRLIVE 2.5GE XPON ONU has several ports and a button, each with a specific function as described in the table below:
| Name | Function |
|---|---|
| 1: PON | Connect to OLT by SC type fiber connector, single mode optical fiber cable. |
| 2/3: LAN1/2 | The blue LAN2 is 2.5GbE port and the yellow LAN1 is 1GE port. Connect to PC or other devices with Ethernet port by Cat5/Cat5E cable, RJ-45 connector. |
| 4: RST | Press RST button over 10 seconds, ONU restores factory default and reboots. |
| 5: DC 12V | Connect with power adapter. DC 12V, 0.5A. |
What is included in the packing list for the AIRLIVE 2.5GE XPON ONU?
| Contents | Quantity |
|---|---|
| 2.5GE XPON ONU | 1 pcs |
| Power adapter | 1 pcs |
| Installation Guide | 1 pcs |
What are the installation environment requirements for the AIRLIVE 2.5GE XPON ONU?
The AIRLIVE 2.5GE XPON ONU equipment must be installed indoors. Please ensure the following conditions are met:
• Confirmation at the ONU installation at sufficient space to facilitate cooling machine.
• ONU suitable operating temperature of -5 °C ~ 55 °C, humidity 10% to 90%.
• Device workplace should avoid radio transmitters, radar stations, and high-frequency interference from power equipment.
How do I install the AIRLIVE 2.5GE XPON ONU on a desktop?
To install the AIRLIVE 2.5GE XPON ONU on a desktop, place the ONU on a clean bench and observe the following:
• Ensure a smooth surface.
• There is enough space around the device for heat dissipation.
• Do not place objects on the device.
How do I mount the AIRLIVE 2.5GE XPON ONU on a wall?
To mount the AIRLIVE 2.5GE XPON ONU on a wall, follow these steps:
1. The ONU chassis has two recesses on the back. In accordance with the position of the groove, install two screws in the wall.
2. The two mounting screws gently snap into the recesses when aligned.
3. Slowly let go, so that the device under the support of the screws is hanging on the wall.
How do I complete the hardware connections for the AIRLIVE 2.5GE XPON ONU?
After placing the AIRLIVE 2.5GE XPON ONU in its desired location (desktop or wall-mounted), connect the fiber, network cable, and power adapter to the corresponding interfaces, and then turn on the power of the product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD AIRLIVE 2.5GE XPON ONU (01) PDF DOCUMENT