ADVENT TOCLS-OE100 (01) PDF MANUAL

Never install this unit where operation and viewing could interfere with safe driving conditions.

To reduce the risk of a traffic accident (except when using for rear view video camera) never use the video display function while driving the vehicle. This is a violation of federal law.

To prevent injury from shock or fire, never expose this unit to moisture or water.

Never disassemble the unit.

Never use irregular discs.

To prevent damage to the mechanism inside this unit, avoid impact to the unit’s monitor.

Using an improper fuse may cause damage to the unit and result in a fire.

Bluetooth – Bluetooth hands-free profile for safety / convenience and A2DP profile for streaming music from a PDA / PMP

Navigation Ready

Infrared Remote Control

Two Composite Video Outputs for Additional Screens

One Audio /Video Auxiliary Inputs

Rotary Encoder Audio Control

Seven-Band EQ with Eleven Preset EQ Curves

Rear Camera Input

Aspect Ratio – 16:9 or 4:3

Fast Forward, Fast Reverse – 2X, 4X, 8X and 16X

Play, Pause, Stop, Next Chapter and Previous Chapter

Direct Track Access via Remote control

Audible Forward / Reverse Track Search

Random, Repeat and Intro

Play, Pause, Stop, Next Track and Previous Track

Station Presets (15 FM1, 15 FM2, 15 FM3, 15 AM)

Auto Stereo/Mono

Auto Store/Preview Scan

Yes, it is compatible with XM and Sirius Tuners (Sold Separately).

Satellite Channel Name, Artist, Song and Categories are displayed on the Monitor.

Access iPod Playlists, Artists, Albums, Songs, *Photos and *Video (* Requires Photo or Video iPod).

Power Management Charges iPod while Connected.

iPod Interface Cable (included).

USB – Supports Hard Drives and Flash Memory Drives.

3.5mm Audio Only Input.

RCA Audio /Video Input.

The TOCLS-100/TOCLJ-100 provides turn-by-turn guidance with a large map and points-of-interest data base.

Yes, the TOCLS-100/TOCLJ-100 is “camera ready.”

Press the front panel PWR button to turn the unit on. The unit can also be turned on by pressing the front remote control power button. To turn the unit off, press and hold the front panel PWR button for 3 seconds (or 2 seconds according to page 7) or press the front remote control power button.

To increase the volume, rotate the front panel PWR-VOL knob clockwise or press the VOL+ button on the front remote control. To decrease the volume, rotate the knob counter-clockwise or press the VOL- button on the remote. The volume level (0 to 40) is displayed for 3 seconds.

Press the MUTE button on the front panel or the PWR VOL button on the front panel or the mute button on the remote control. “MUTE” (or a speaker icon with a slash) is displayed. Press the MUTE button again, adjust the volume, or use an audio setup feature to restore the audio. Pressing the front panel PWR button also unmutes.

Press the Eject button (▲). Disc play stops, the disc is ejected, and the unit changes to radio operation. If the disc isn’t removed within 10 seconds, it will be automatically re-loaded. If the button is pressed again while the disc is out, it will re-load.

In Radio mode, pressing these buttons acquires the next available frequency up (▲) or down (▼). In iPod/MP3/USB/SD player mode or Satellite radio mode, they select the next (▲) or previous (▼) song or channel.

In Radio mode, pressing the knob acquires the next or previous available frequency. In iPod/MP3/USB/SD player mode, it selects a song. In Satellite radio mode, it selects a channel.

Press the NAV button on the front panel. Alternatively, access the Main Menu and select the NAV icon.

This is a shortcut to access the Navigation mode and enter a desired destination.

Press to repeat the voice guidance or instructions while in Navigation mode.

Press the MENU button on the front panel or press MENU on the front panel remote control.

It is a 3.5mm jack providing an audio or video input.

To correct a system halt or other illegal operation, use the tip of a pen to press the reset button located on the front bottom right corner of the unit.

The microphone is located on the left side of the unit. Speak loudly and clearly for best reception.

Press to switch between the various audio sources (e.g., Radio, CD, USB). Press and hold for 2 seconds to turn the audio off.

Press FAV to access AM, FM, and Satellite Radio presets directly. If you switch modes (e.g., from Sat. Radio to DVD) and press FAV, it returns to Sat. Radio presets. Press repeatedly to cycle through preset groups (1-6, 5 presets each). To save a channel as a favorite, tune to the desired channel, access the desired preset group and location, then press and hold the location for 2 seconds.

Press the front panel TUNE SEL knob or press SEL on the remote control to access the Equalizer Control Menu.

Use the right/left cursor buttons under “EQ SETTING” to select one of eleven preset modes: User, Flat, Jazz, Pop, Classical, Rock, News, Urban, Rave, Movie, Techno.

When “EQ SETTING” is set to USER, you can adjust Bass, Treble, Balance, Fade, and Subwoofer levels.

Select the feature (e.g., BASS) using the TUNE SEL knob or remote buttons.

Press and hold the left/right cursor buttons next to the feature name to adjust its value (shown numerically).

Bass and Treble levels cannot be changed when a preset sound (Flat, Jazz, etc.) is selected.

Press the TUNE SEL Knob to exit the equalizer menu screen.

1. Access the Main Menu (press MENU button on unit or remote).

2. Press the SETUP icon.

3. In the SETUP menu, press the CLOCK icon.

4. In the CLOCK submenu, press the SET TIME icon.

5. A keyboard will appear. Enter the time in HH:MM format.

6. Press the AM or PM icon.

7. Press OK.

8. Optionally, press the 12/24 HOUR FORMAT icon and select the desired format.

AM/FM: Access AM/FM TUNER mode.

CD/DVD: Access CD/DVD mode (Disc must be inserted).

SD CARD: Access SD Card contents (SD card must be inserted).

USB: Access USB thumb drive contents (USB drive must be connected).

BLUETOOTH: Access the Bluetooth menu.

CAMERA: Access signal from an external camera.

REAR: Display DVD video on rear monitors (if equipped).

SETUP: Access the unit’s setup menu (General, Video, Audio, etc.).

AV 2: Access the AV2 audio/video input (iPod, USB, 3.5mm jack via interface module). Icon changes to iPod if connected.

AV 1: Access the AUX INPUT mode (front panel 3.5mm jack).

NAV: Access the navigation mode.

SAT: Access the satellite radio function (Icon shows XM or SIRIUS logo depending on service).

Press the unit’s front panel MENU button or the MENU button on the front remote control. Then press the SETUP icon. Press the BLUETOOTH icon in the GENERAL Submenu and set the Bluetooth to ON.

Note: Procedures may vary slightly by phone manufacturer.

1. On your phone, select the Bluetooth setup option.

2. Turn Bluetooth ON and set your phone’s discover mode to ON (may have a time limit).

3. Use your phone’s “add new device” feature. The unit (e.g., “Advent”) should appear.

4. Select the unit on your phone. If prompted for a passkey or pairing code on the phone, enter “1234”. (The unit’s default code is 1234. Some phones default to “0000”. Ensure the unit’s pairing code setting matches if needed).

5. A prompt to pair/bond should appear on your phone. Accept the request.

6. A prompt asking to connect to the unit (Yes/No) may appear. Select Yes.

7. Pairing should be successful. The Bluetooth main menu appearing on the unit’s screen confirms pairing.

1. Press the front panel MENU button, then the BLUETOOTH icon.

2. On your phone, enable Bluetooth and set it to discoverable mode.

3. On the unit’s Bluetooth main menu, press the DEVICES icon.

4. On the DEVICES screen, press the ADD icon. The unit will start searching.

5. When your phone name appears under “Device Found”, select it and press the CONNECT icon.

6. A keypad may appear on the unit. Enter the PIN/Passkey for your phone (often “0000” or check phone manual) and press OK.

7. Your phone should display a prompt like “Pairing request from [Unit Name]… Accept? Yes/No”. Select Yes.

8. Your phone may then prompt you to enter the unit’s PIN/Passkey. Enter “1234” and confirm (ENTER, OK, etc.).

9. A “Connecting…” message appears on the unit, followed by “[Phone Name] Connected!”. Press Close.

10. The Bluetooth main menu reappears, confirming the pairing.

11. If pairing fails (e.g., “PIN code error”), a message appears. Press RETRY and repeat steps 7-9.

When connected via Bluetooth, the unit mutes audio output, pauses CD play, and shows the Bluetooth call screen when a call is received. The incoming number or name appears, an audible tone sounds, and a graphic display appears.

Press the green phone icon on the screen. Speak loudly and clearly towards the microphone on the lower left side of the unit. To end the call, press the red phone icon.

Press the red phone icon on the screen. The call reverts to your wireless phone for voicemail.

1. Access the Bluetooth main menu (MENU > BLUETOOTH icon).

2. The Phone screen with a keypad appears.

3. Use the 0-9, */+, # buttons to input the phone number. Press ‘C’ to clear the last digit or the entire number.

4. Press the green phone icon to dial.

5. To end the call, press the red phone icon.

1. Access the Bluetooth main menu (MENU > BLUETOOTH icon).

2. Press the CONTACTS icon.

3. Use the scroll arrows (▲/▼) or the letter buttons (A-L, M-X, Y-Z toggled by center arrows) to find the desired contact.

4. Press the contact name, then press the phone number icon next to the name to dial.

5. To end the call, press the red phone icon.

The Contacts List is a copy of the contact list from your paired wireless phone. You can scroll through contacts using arrows or jump to letters using the center key board letters (A-L, M-X, Y-Z). The outer arrows scroll the list in groups of five.

Connect your iPod using the adapter cable to the AV2 Interface Module. Select AV2 from the Main Menu (icon changes to iPod).

Navigation: Use the menu on the right (Playlists, Artists, Albums, Genres, Songs, Composers, Audiobooks, Podcasts) to browse content. Pressing a category lists items; pressing an item starts playback.

Playback Controls:

SCAN: Plays the first 10 seconds of each track.

►/|| (Play/Pause): Start or pause playback.

Shuffle Icon: Plays tracks in random order.

Previous Icon: Go to the previous item/track.

Repeat Icon (Sכ): Press once to repeat current song. Press again (Aכ) to repeat all in the current directory/list. Press again to turn off repeat.

Preset List Next/Previous Icons: Navigate pages in the menu list.

Mute/Un-mute Icon: Mute or unmute audio.

<< / >> Icons: Show/hide additional bottom-row buttons.

■ (Stop): Stop playback. Press play to resume.

►► (Next): Go to the next item/track.

Music/Video Icons: Switch between audio and video menus/modes (if iPod supports video).

Video Menu (Requires Video iPod): Access Movies, Music Videos, TV Shows, Video Podcasts, Rentals lists.

Keyboard Icon/Direct Tuning: Press the keyboard icon. Enter the track number corresponding to the menu list using the numeric keypad and press OK to play that item directly.

1. Connect your device’s output (Yellow=Video, Red=Right Audio, White=Left Audio RCA jacks) to the AVIN 3.5mm jack on the front panel using an appropriate adapter cable.

2. Turn on the source component.

3. Press the unit’s MENU button and select AV1.

4. Use the source device’s controls for playback.

5. Note: For video display, the vehicle’s parking brake must be engaged. Otherwise, a warning screen appears.

The AV2 input uses the AV2 Interface Module (location may vary). It accepts USB devices, a 3.5mm jack input, or an iPod via the iPod adapter cable (connects to USB and AV2 ports on the module).

1. Connect your device to the appropriate port on the AV2 Interface Module.

2. Turn on the source component (if necessary).

3. Press the unit’s MENU button and select AV2 (icon may change based on device).

4. Use the source device controls or the unit’s controls (for iPod/USB) for playback.

5. If no video signal is present, “VIDEO NOT DETECTED” appears. For video display, the vehicle’s parking brake must be engaged. Otherwise, a warning screen appears.

1. Select Navigation mode (NAV button or Main Menu > NAV icon). The software will load.

2. Read the “PLEASE DRIVE SAFELY” warning and press “Press to accept”.

3. The Navigation main menu appears. Press the “Go To…” icon.

4. Select a destination method (e.g., Point of Interest).

5. Choose criteria (e.g., State/Province > By Category > Airport > Sort by Distance).

6. Select the specific destination (e.g., the desired airport).

7. The system calculates the route. Follow the visual guidance on the map and audible instructions.

8. The system will announce when you have arrived at your destination.

Select SAT from the Main Menu (XM logo shown).

Menu Icons:

CHANNELS: Press to view the channel list. Use arrows (▲/▼) to navigate. Current channel highlighted.

CATEGORY: Press to view categories (jazz, rock, etc.). Use arrows (▲/▼) to navigate.

PRESETS: Press to view stored preset channels. Use arrows (▲/▼) to view available presets. Press and hold a preset slot for ~2 seconds to save the current channel.

Other Icons:

Preset List Next/Previous: Navigate pages in the menu list.

Mute/Un-mute: Mute/unmute audio.

Next/Previous Category (◄ / ►): Advance to the next/previous available category.

Jump: Switch between the current and previously tuned channel.

Keyboard Icon (Direct Tune): Press icon, enter channel number using keypad, press OK.

XM Radio ID: Press Keyboard icon, enter 0, press OK. The 8-character alphanumeric ID will be displayed.

Select SAT from the Main Menu (SIRIUS logo shown).

Menu Icons:

Channels: Press to view the channel list. Use arrows (▲/▼) to navigate.

Presets: Press to view stored preset channels. Use arrows (▲/▼) to view. Press and hold a preset slot for ~2 seconds to save current channel.

Categories: Press to view categories. Use arrows (▲/▼) to navigate.

Settings: Access SIRIUS Radio ID, Parental Control, Password Edit, Version Info.

Other Icons:

Preset List Next/Previous: Navigate pages in the menu list.

Mute/Un-mute: Mute/unmute audio.

Next/Previous Category (◄ / ►): Advance to the next/previous available category.

Jump Icon: Switch between current and previous channel.

Keyboard Icon (Direct Tune): Press icon, enter channel number (0-223) using keypad, press OK.

SIRIUS Radio ID: Go to Settings > Press SID icon. The 12-digit ID is displayed.

SIRIUS Version: Go to Settings > Press Sirius Version icon.

1. Go to Menu > Settings > Parental Control.

2. Press Lock/UnLock Channels.

3. Enter the password (default is 0000) and press OK.

4. A list of channels appears. Channels with a lock icon (🔒) are blocked and not accessible.

5. To lock a channel, press the channel name/icon. The lock icon will appear.

6. To unlock a channel, press the channel name/icon with the lock. The lock will open/disappear, making the channel accessible.

1. Go to Menu > Settings > Parental Control.

2. Press Edit Password.

3. Enter the current password (default is 0000) and press OK.

4. Enter the new four-digit password you want to use and press OK.

5. Enter the new four-digit password again to confirm and press OK.

6. The password is now changed.