Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** Acer Projector KI 30/L220/LK-W11 Series User’s Guide
****** Page 2 ****** Copyright 0 2011. Acer Incorporated. All Rights Reserved. Acer Projector K130/L220/LK-W11 Series User’s Guide Original Issue: 12/2011 Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose. Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your projector. All correspondence concern ing your unit should include the serial number, model number and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transm itted, in any form or by any means, electron ically, mechan ically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated. Acer Projector K130/L220/LK-W11 Series Model number: Serial number: Date of purchase: Place of purchase: Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies’ product names or trademarks are used herein for identification purposes only and belong to their respective companies. HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. “
****** Page 3 ****** ili Information for your safety and comfort Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Caution for plug as disconnecting device Observe the following guidelines when connecting and disconnecting power to the external power supply unit: Install the power supply unit before connecting the power cord to the AC power outlet. Unplug the power cord before removing the power supply unit from the projector. If the system has multiple sources of power, disconnect power from the system by unplugging all power cords from the power supplies. Caution for Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet. Warnings! Do not use this product near water. Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.
****** Page 4 ****** To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface. Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices. Using electrical power This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord. If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip’s input rating. This product’s AC adapter is equipped with a three-wire grounded plug. The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the AC adapter plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details. Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury. Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product. Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length.
****** Page 5 ****** Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel Unplug this product from the wall outlet and refer servicing to qualified service personnel when: the power cord or plug is damaged, cut or frayed liquid was spilled into the product the product was exposed to rain or water the product has been dropped or the case has been damaged the product exhibits a distinct change in performance, indicating a need for service the product does not operate normally after following the operating instructions Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Warning! For safety reasons, do not use non-compliant parts when adding or changing components. Consult your reseller for purchase options. Your device and its enhancements may contain small parts. Keep them out of the reach of small children. Additional safety information Do not look into the projector’s lens when the light is on. The bright may hurt your eyes. Turn on the projector first and then signal sources Do not place the product in following environments: Space that is poorly ventilated or confined. At least 50cm clearance from walls and free flow of air around the projector is necessary. Locations where temperatures may become excessively high, such as inside of a car with all windows rolled up. Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten ing the life span and darkening the image. Locations near fire alarms. Locations with an ambient temperature above 40 00104 OF. Locations where the altitudes are higher than 10000 feet. Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector. It
****** Page 6 ****** might cause fire or electric shock. In this case, unplug immediately and contact your dealer. Do not keep using this product to break or drop it. In this case contact your dealer for inspection. Do not face the projector lens to the sun. It can lead to fire. When switching the projector off, suggest to ensure the projector completes its cooling cycle before disconnecting power. Do not frequently turn off the main power abruptly or unplug the projector during operation. The best way is to wait for the fan to turn off before turning main power off. Do not touch air outlet grille and bottom plate which becomes hot. Clean the air filter frequently if have. The temperature inside may rise and cause damage when the filter/ventilation slots clogged with dirt or dust. Do not look into the air outlet grille when projector is operating. It may hurt your eyes. Always open the lens shutter or remove the lens cap when the projector is on. Do not block the projector lens with any object when the projector is under operation as this could cause the object to become heated and deformed or even cause a fire. Do not attempt to disassemble this projector. There are dangerous high voltages inside which may hurt you. Refer servicing only to suitable qualified professional service personnel. Do not stand the projector on end vertically. It may cause the projector to fall over, causing injury or damage. Caution for Listening To protect your hearing, follow these instructions. Increase the volume gradually until you can hear clearly and comfortably. Do not increase the volume level after your ears have adjusted. Do not listen to music at high volumes for extended periods. Do not increase the volume to block out noisy surroundings. Decrease the volume if you can’t hear people speaking near you.
****** Page 7 ****** Vli Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit acer-group.com/public/Sustainability/sustainability01.htm
****** Page 8 ****** VIII First things first Usage Notes Turn off the product before cleaning Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don’t: Block the slots and openings on the unit provided for ventilation. Use abrasive cleaners, waxes or solvents to clean the unit. Use under the following conditions: In extremely hot, cold or humid environments. In areas susceptible to excessive dust and dirt Near any appliance that generates a strong magnetic field. Place In direct sunlight. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s guide to maximize the life of your unit. Warning: Do not look into the projector’s lens when the light is on. The bright may hurt your eyes. To reduce the risk of fire or electric shock, do not expose th is product to rain or moisture. Please do not open or disassemble the product as th is may cause electric shock. When switch ing the projector off, please ensure the projector completes its cooling cycle before disconnecting power. Turn on the projector first and then the signal sources. Do not use lens cap when projector is in operation.
****** Page 9 ****** Information for your safety and comfort First things first Usage Notes Precautions Introduction Product Features Package Overview Projector Overview Projector Outlook Control Panel Remote Control Layout Getting Started Connecting the Projector Turning the Projector On/Off Turning on the Projector Turning the projector off Adjusting the Projected Image Adjusting the Height of Projected Image How to optimize image size and distance User Controls Installation menu Acer Empowering Technology Onscreen Display (OSD) Menus Color Image Setting Management Audio Language How to Play iPhone/iPod/iPad Media via 1<130/L220/LK WI 1 How to play photos iii viii VIII VIII 1 1 2 3 3 4 5 7 7 8 8 9 10 10 11 13 13 14 15 16 17 19 19 20 20 21 22 22 ****** Page 10 ****** How to play videos Appendices Troubleshooting LED & Alarm Definition Listing Specifications Compatibility modes Regulations and safety notices 24 25 25 29 30 32 36 ****** Page 11 ****** 1 Introduction Product Features This product is a single-chip DLP@ projector. Outstanding features include: DLP@ technology 1280 x 800 WXGA resolution 4:3/16:9/Full/L.Box aspect ratio supported Versatile display modes (Bright, Presentation, Standard,Video, Picture, Game, User) enable optimum performance in any situation NTSC/PAL/SECAM compatible and HDTV (480i/p, 576i/p, 720p, 1080i/p) supported Compact size projector facilitates business purposes and home entertainment. Acer EcoProjeciton Technology delivers Intelligent power management approach and physical efficiency improvement Empowering Key reveals Acer Empowering Technology utilities (Acer eView, eTimer, e3D, ePower Management) for easy adjustment of settings Equipped with HDMITM connection supporting HDCP Advanced digital keystone correction delivers optimum presentations Multi-language on screen display (OSD) menus 1.67x digital zoom and pan move function Environmental light source and longer life by LED solution. Enjoy media playback via USB, RAM and Micro SD card reader. Microsoft@ Windows@ 2000, XP, Vista Windows@ 7, Macintosh@ OS compliant ****** Page 12 ****** 2 Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if any thing is missing. Projector 3.5 mm jack AN cable Battery Adapter for iPod/iPhone/ iPad (Optional) Power cord Universal to D-sub and Audio out cable User's Guide x2 Carrying case (Optional) AC to DC power adapter öeo ooo 000 ooo Remote control Qu ick start guide ****** Page 13 ****** 3 Projector Overview Projector Outlook Front / upper side 4 5 6 3 1 2 3 2 Description Projection lens Tilt adjusting wheel Focus ring 1 Rear side 2 4 5 6 micros* Description Power button Control panel Remote control receiver USB 1 2 3 4 1 4 Description Remote control receiver MicroSD Card Slot USB connector 3 HDMI AV IN 5 6 DC IN 7 Description 5 6 7 HD MI connector AV Input Connector DC Input Un iversal connector for VGA/ Audio in/ Audio out connector ****** Page 14 ****** 4 Control Panel 4 5 SOURCE MENU 3 6 2 Icon 1 2 3 4 5 6 Function POWER MENU SOURCE LAMP TEMP Description Power button and Power Indicator LED. See the contents in "Turning the Projector On/Off" section. Press 'i MENU" to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu. Changes the active source. Lamp Indicator LED Temp Indicator LED Four directional select Use the keys to select items or make keys adjustments to your selection. ****** Page 15 ****** Remote Control Layout 2 3 5 8 10 – 12 15 F.ec Parex Electronics & Computer CO.,LTD. MADE IN CHINA VZ.JE600.001 ö€)01 peel escnp Ion 5 1 4 6 7 9 11 13 16 2 3 4 5 6 7 8 9 10 11 12 13 con O un Ion Infrared transm itter FREEZE POWER HIDE ASPECT RATIO RESYNC SOURCE STOP P ayæause MENU Four Irecüona select keys MEDIA Sends signals to the projector. To pause the screen image. Re er tot e "Turning t e Projector On/O " section. Momentari y turnso t e VI eo. Press "HIDE" to I et e image, press again to display the image. To pause t e screen mage. Automatica y sync romzest e proJector tot e Input source. Press "SOURCE" to c oose rom RGB, Component, S-VI eo, Composite, Video and HDTV sources. Press "Stop" to stop p ayqng me la I e. Press "P ay/Pause" to p ay/pause me la I e. Press VIMENU" to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu. Use up, own, e , mg t uttonsto se ect Items or ma e adjustments to your selection. Press "MEDIA" to toggle between USB A, Micro SD and RAM sources. This projector supports various file formats of photo/ audio/ video. Empowering ey Umque Acer unctions: eVlew, eTmer, e3D an ePower Management. Press "O" key under Micro SD/USB ARAM source, the setting page will be shown for user's adjustment. ****** Page 16 ****** 6 14 15 16 unction con O LANWIFI O HDMI/VGA AV Press Press Press escri tion "LANANIFI" to change source to LANMIFI. "HDMI MNGA" to change source to HDMITMNGA. "AVI' to change source to AV. ****** Page 17 ****** 7 Getting Started Connecting the Projector 101 microsz USB 10 8 9 escnptlon 1 AC to DC power adapter 2 Power cord USB disk/stick 3 USB WiFi adapter 4 Micro SD card 5 Adapter for iPod/iPhone/iPad HDMI 7 HDMI DVD player o: 2 iPod/iPhone/iPad O 6 escriptlon 6 7 8 9 10 3.5 mm jack AN HDMI cable Un iversal to D-sub and Audio out cable Un iversal to RCA cable Audio cable Jack/RCA Note: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector. ****** Page 18 ****** 8 Turning the Projector On/Off Turning on the Projector 1 2 3 Ensure that the power cord and signal cable are securely connected. The Power indicator LED will flash red Turn on the projector by pressing " Power" button on the control panel, and the Power indicator LED will turn blue.(lllustration #1) Turn on your source (computer, notebook, video player ,etc.). The projector will detect your source automatically. If the screen displays "No Signal", please make sure the signal cables are securely connected. If you connect to multiple sources at the same time, use the "Source " button on either control panel or the remote control or direct source key on the remote control to switch between inputs. Power button ****** Page 19 ****** 9 Turning the projector off 1 2 3 4 To turn the projector off, press the power button. This message appears: " Please press the power button again to complete the shutdown process. " Press the power button again. The LED power indicator will turn RED and blink rapidly after the projector is turned off, and the fan(s) will continue to operate for about 30 sec to ensure that the system cools properly. Once the system has finished cooling, the LED power indicator will stop blinking and turn solid red to indicate standby mode. It is now safe to unplug the power cord Warning indicators: " Projector Overheated. Will automatically turn off soon." This onscreen message indicates that the projector has overheated. The projector will automatically shut down. Contact your local dealer or service center. "Fan failed. Will automatically turn off soon." This onscreen message indicates that the fan has failed. The projector will automatically shut down. Contact your local dealer or service center. Note: Whenever the projector automatically shuts down, contact your local reseller or service center. ****** Page 20 ****** 10 Adjusting the Projected Image Adjusting the Height of Projected Image The projector is equipped with tilt adjusting wheel for adjusting the height of image. To raise/lower the image: 1 Use Tilt adjusting wheel to fine-tune the display angle. 1 1 1 1 Tilt adjusting wheel ****** Page 21 ****** 11 How to optimize image size and distance Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen. Example: If the projector is 1.34 m from the screen, good image quality is possible for image sizes 41.51' Note: Remind as below figure, the space of 56 cm height is required when located at 1.34 m distance. Screen size 41.5" Height: 56crn 1.34m Desired Distance ****** Page 22 ****** 12 Desired D istance (m) 0.97 I. 07 1.34 1.61 2.14 Screen size (Min zoom) Diagonal (inch) W (cm) x H (cm) 30.0 33.2 41.5 49.7 66.3 80.0 64 x 40 71 x 45 89 x 56 107 x 67 143 x 89 172 x 108 Top From base to top of image (cm) 40 45 56 67 89 108 2.58 Zoom Ratio: 1.0x ****** Page 23 ****** 13 User Controls Installation menu The installation menu provides an onscreen display (OSD) for projector installation and maintenance. Use the OSD only when the message " No signal input" is displayed on the screen. The menu options include settings and adjustments for screen size and distance, focus, keystone correction and more . 1 2 3 4 5 Turn on the projector by pressing "Power" button on the control pad Press the "MENU" button on the control pad to launch the OSD for projector installation and maintenance. nnn uvu uua Installation Projection Menu Location Auto Kerston• Keystone Language Reset Select English Enter The background pattern acts as a guide to adjusting the calibration and alignment settings, such as screen size and distance, focus and more . The Installation menu includes the following options: •Projection method •Menu location •Auto Keystone settings •Manual Keystone settings •Language settings •Reset to factory default function Use the up and down arrow keys to select an option, the left and right arrow keys to adjust selected option settings, and the right arrow key to enter a submenu for feature setting. The new settings will be saved automatically upon exiting the menu. Push the menu button anytime to exit the menu and return to the Acer welcome screen. ****** Page 24 ****** 14 Acer Empowering Technology Acer Empowering Key provide four Acer unique functions, they are " Acer eView Management" , "Acer eTimer Management" , "Acer ePower Management" and i' Acer e3D Management respectively. key to launch the Onscreen display main menu to modify its Press function. When the Empowering Menu is displayed, use the key to select the main menu. Acer eView Management e mpowering Menu Acer eView Management Game vser Acer eTimer Management e mpowering Menu Acer eTi1Tter Management start Alarm O Minutes Middle countdown Acer ePower Management e mpowering Menu Acer ePower Management CCC' Auto Acer e3D Management e mpowering Menu Acer e3D Management " Acer eView Management" is for display mode selection. Please refer to Onscreen Display Menus section for more detail. " Acer eTimer Management" provides the reminding function for presentation time controL Please refer to Onscreen Display Menus section for more detail. " Acer ePower Management" provides user one shortcut to save the projector life. Please refer to Onscreen Disp lay section for more detail. " Acer e3D Management" provides the 3D functions. Please refer to Onscreen Display Menus section for more detail. 30 S',mc melt 3D warn•ng Mess»ae invert ****** Page 25 ****** 15 Onscreen Display (OSD) Menus The projector has multilingual OSD that allow you to make image adjustments and change a variety of settings. Using the OSD menus To open the OSD menu, press "MENU" on the remote control. When the OSD is displayed, use the A v keys to select any item in the main menu. After selecting the desired main menu item, press to enter submenu for feature setting. Use the keys to select the desired item and adjust the settings by using the keys. Select the next item to be adjusted in the submenu and adjust as described above. Press "MENU " on the remote control, the screen will return to the main menu. To exit OSD, press "MENU" on the remote control again. The OSD menu will close and the projector will automatically save the new settings. Main menu J Color Chsolay Mode BngHness Ccnrest Sanrd:jcn Advanced Select Sub menu Standard 50 Press Setting ****** Page 26 ****** 16 Color Display Mode Wall color Brig htness Contrast Saturation Tint Color e:nn.ness COCO&V S*.rabon There are many factory presets optimized for various types of mages. Bright: For brightness optimization. Presentation: For meeting presentation. Standard: For common environment. Video: For playing video in a bright environment. Picture: For graphic picture. Game: For game content. User: Memorize user's settings. Use this function to choose a proper color according to the wall There are several choices, including white, light yellow, light blue, pink, dark green. It will compensate the color deviation due to the wall color to show the correct image tone. Adjust the brightness of the image. Press < to darken image. Press to lighten the image. "Contrast" controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press < to decrease the contrast. Press to increase the contrast. Adjusts a video image from black and white to fully saturated color. Press to decrease the amount of color in the image. Press to increase the amount of color in the image. Adjusts the color balance of red and green. Press to increase the amount of green in the image. Press to increase the amount of red in the image. ****** Page 27 ****** Advanced Image Projection Aspect Ratio 17 Color Temperature Adjust the color temperature. At higher color temperatures, the screen looks colder; at lower color temperatures, the screen looks warmer. Degamma Effects the representation of dark scenery. With greater gamma value, dark scenery will look brighter. Dynamic Black Choose "On " to automatically optim ize the display of dark movie scenes enabling them to be shown in incredible detail. Note: "Saturation" and "Tint" functions are not supported under computer mode or HDMI mode. Image Front-Desktop The factory default setting. Front-Ceiling • When you select this function, the projector inverts the image for ceiling-mounted projection. Rear-Desktop • When you select this function, the projector reverses the image so you can project from beh ind a translucent screen. Rear-Ceiling When you select this function, the projector reverses and inverts the image at same time. You can project from beh ind a translucent screen with ceiling mounted projection. Use this function to choose your desired aspect ratio. 16:9 Auto: Keep the image with original width-h igth ratio and maxi m ize the image to fit native horizontal or vertical pixels. 4:3: The image will be scaled to fit the screen and displayed using a 4:3 ratio. 16:9: The image will be scaled to fit the width of the screen and the height adjusted to display the image using a 16:10 ratio. Full: Resize image to fit full screen by width (1280 pixels) and height (800 pixels). L.Box: Keep original signal aspect ratio and zoom in by 1.333 times. ****** Page 28 ****** 18 Auto Keystone Manual Keystone Sharpeness H. Position (Horizontal position) V. Position (Vertical position) Frequency Tracking Automatically adjusts vertical image. Adjust image distortion caused by tilting projection. (±40 degrees) The Manual Keystone funcion is unavailable under Auto Keystone setting to “On ” . Adjusts the sharpness of the image. Press Press Press Press Press Press to decrease the sharpness. to increase the sharpness. to move the image left. to to move the image right. to move the image down. to move the image up. ” Frequency” changes the projector’s refresh rate to match the frequency of your computer’s graphics card. If you can see a vertical flickering bar in the projected image, use th is function to make the necessary adjustments. Synchron izes the signal tim ing of the projector with the graphics card. If you experience an unstable or flickering image, use this function to correct it. HDMI Color Range Adjust the color range of the HDMI image data to correct color display error. • Auto: Automatically adjust by information from player. Limited Range: Prosess the input image as limited color range data. Full Range: Prosess the input image as full color range data. HDMI Scan Info Adjust the overscan ratio of the HDMI image on screen. Auto: Automatically adjust by information from player. Underscan: Always no overscan on HDMI image. Overscan: Always keep overscan on HDMI image. Note: “H. Position “V. Position “Frequency” and “Tracking” functions are not supported under HDMI or Video mode. Note: “Sharpness” functions is not supported under HDMI and Computer mode. Note: “HDMI Color Range” and “HDMI Scan Info” functions are only supported under DVI mode.
****** Page 29 ****** Setting Menu Location Closed Caption Reset 19 Setting Ptess Choose the menu location on the display screen. Selects a preferred closed captioning mode from CCI, CC2, CC3, CC4, (CCI displays captions in the primary language in your area). Select “Off” to turn off the caption ing feature. This function is only available when a composite video or S-Video input signal is selected and its system format is NTSC. Set your screen aspect ratio to 4:3. Th is function is not available when the aspect ratio is ” 16:9″ or “Auto” . Press the button and choose “Yes” to return the parameters on all menus to the factory default settings. Management ECO Mode High Altitude Auto Shutdown LED Calibration Managemen Higrt Auto LEO 4) Choose “On” to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose “Off” to return normal mode. Choose “On” to turn on High Altitude mode. Operate the fans at full speed continuously to allow for proper high altitude cooling of the projector. The projector will automatically shutdown when there is no signal input after the allocated time. (in minutes) Press after choosing “Yes”, please wait for 10 seconds to finish the wh ite color fine tune process. It helps to adjust LED color performance.
****** Page 30 ****** 20 Audio Volume Mute Alarm Volume 3D Sync Invert Audio A*’rt Press to decrease the volume. Press to increase the volume. Choose “On” to mute the volume. Choose “Off” to restore the volume. Select this function to adjust the volume of any warn ing notifications. Choose ” On” to enable DLP 3D function. On: Choose this item while using DLP 3D glasses, quad buffer (NVIDIA/ATI…) graphic card and HQFS format file or DVD with corresponding SW player. • Off: Turn off 3D mode. If you see a discrete or overlapping image wh ile wearing DLP 3D glasses, you may need to execute ” Invert” to get best match of left/right image sequence to get the correct image (for DLP 3D).
****** Page 31 ****** 21 3D Warning Message Choose “On” to display the 3D warning message. Note: 30 display is now enabled. t. Please make sure you hate the correct 30 signalS ard glasses, 2. Rernernber to turn 30 of f you dent want to see 30 images. 3. Ifthe 30 display isnt correct, please to enable 3D Sync Invert. 4. Display nude options Will be disabled while mde, Note: It needs correct settings on graphic card 3D application program for correct 3D display. Note: The SW players, such as Stereoscopic Player and DDD TriDef Media Player can support 3D format files. You can download these three players on web page below, – Stereoscopic Player (Trial): http:/mww.3dtv.at/Downloads/lndex_en.aspx – DDD TriDef Media Player (Trial): http:mmww.tridef.com/download/TriDef-3-D-Experience-4.0.2.html Note: “3D Sync Invert” is only available when 3D is enabled Note: There has rem inder screen if 3D still enable when power on projector. Please adjust setting depended on your purpose. Language Language Language Cegtini’ Viano Ent*’ Choose the multilingual OSD menu. Use the to select your preferred menu language. Press to confirm the selection. key
****** Page 32 ****** 22 How to Play iPhone/iPod/iPad Media via KI 30/L220/LK-W11 Adjust K130/L220/LK-W11 source upto “AVI’ and make sure to plug adapter with iPod/iPhone/iPad well iPod/iPhone/iPad o AV IN 1 DC I 1 2 Description 3.5 mm jack AN cable Adapter for iPod/iPhone/iPad How to play photos If using iPhone, Follow below steps 1. Press application ” Photos” on main screen and choose album. 2. Press in thumbnail page. e If using iPod, otos 95 Photos 133 Photos About us 1 u Pnotos Anniversary 4′ Photos TOKYO Photos Settings . oo Photos Rings Time Per Slide Music Res:Eat Shuffle Photos ransitions TV Out TV Signal Off Oft On NTSC 429 Photos Note : Please make sure Photo setting in advance. If by iPod Nano: Photos Settings If by iPod Classic : Slideshow Settings a. TV Out: choose On b. TV Signal: choose NTSC
****** Page 33 ****** 23 Follow below steps 1. Choose photos and then choose which album you want. (ex. TOKYO) 2. If by iPod Nano Pod Video Playlists Extras Settings Sleep Shuffle Songs Now Playing press II when thumbnail mode. mtotos 2009.01.07wnmVJE 95 Photos 133 Photos About us IBO Photos Anniversary Photos TOKYO Settings . 422 Photos TOKYO Septernb•er 2. 200& 3. If by iPod Classic : press to enter i’ slideshow” mode and photo will be output automatically via K130/L220/LK-W11. TOKYO ’22 Photos Septernber 2. 2001 Video Playlists Extras Settings Sleep Shuffle Songs Now Playing If using iPad, 29 Follow below steps: 1. Press application 2. Press “Slideshow” 95 PLOIos 133 Ab.out us 180 Pnot0b Anniversary Phfit:-ys TOKYO Settings photos “Photos” on main screen. -5 ” Start Slideshow” Slideshow Options may Transition Start Slideshow
****** Page 34 ****** 24 How to play videos If using iPhone, Follow below steps 1. Press application “Videos” in main screen. 2. Press video clip you want in Video clip listing, then video will be output automatically via K130/L220/LK-W11. Videos MP2t7Ht ppgma•pao FREE Wi Remote csag If using iPad, Follow below steps: 1. Press application “Videos” on main screen 2. Press video clip you want in video clip listing and press then video will be output automatically via K130/L220/LK-W11 Info Chapters Videos
****** Page 35 ****** 25 Appendices Troubleshooting If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center. Image Problems and Solutions 2 Problem No image appears onscreen Partial, scrolling or incorrectly displayed image (For PC (Windows 95/98/2000/XP/ VistaANin7)) Solution Connected as described in the “Getting Started section. Ensure none of the connector pins are bent or broken. Make sure the projector is switched on. Press ‘IRE-SYNC’I on the remote control. For an incorrectly displayed image: Open “My Computer,” open the “Control Panel,” and then double-click the “Display” Icon. Select the “Settings” tab. Verify that your display resolution setting is lower than or equal to 1080P-ElA. Click the “Advanced Properties” button. If the problem still appears, change the monitor display you are using and follow the steps below: Verify that the resolution setting is lower than or equal to 1080P-ElA. Click the “Change” button under the “Monitor” tab. Click “Show all devices”. Next, select “Standard monitor types” under the SP box, and choose the resolution mode you need under the “Models” box. Verify that the resolution setting of the monitor display is lower than or equal to 1080P-ElA.
****** Page 36 ****** 26 3 4 5 6 7 8 Partial, scrolling or incorrectly displayed image (for notebooks) The screen of the notebook computer is not displaying your presentation Image is unstable or flickering Image has vertical flickering bar Image is out of focus Image is stretched when displaying a “widescreen ” DVD title Press “RESYNC” on the remote control. For an incorrectly displayed image: Follow the steps for item 2 (above) to adjust the resolution of your computer. Press the toggle output settings. Example: [Fn]+[F4], Compaq Dell Gateway IBM HP NEC Toshiba ] If you experience difficu Ity changing resolutions or your mon itor freezes, restart all equipment including the projector. If you are using a Microsoft@ Windowse based notebook: Some notebook PCs may deactivate their own screens when a second display device is in use. Each has a different way to be reactivated. Refer to your computer’s manual for detailed information. If you are using an AppleO Mace OS based notebook: In System Preferences, open Display and select Video Mirroring “On Adjust the “Tracking ” to correct it. Refer to the “Image” section for more information. Change the display color depth settings on your computer. Use “Frequency” to make an adjustment. Refer to the ” Image” section for more information. Check and reconfigure the display mode of your graph ics card to make it compatible with the projector. Adjusts the focus ring on the projector lens. Make sure the projection screen is within the required distance of 3.18-8.46 feet (0.97-2.58 meters) from the projector. Refer to the “How to Get a Preferred Image Size by Adjusting Distance and Zoom” section for more information. When you play a DVD encoded in anamorphic or 16:9 aspect ratio you may need to adjust the following settings: If you play a 4:3 format DVD title, please change the format to 4:3 in the projector OSD. If the image is still stretched, you will also need to adjust the aspect ratio. Set up the display format to 16:9 (wide) aspect ratio on your DVD player. If you play an Letterbox(LBX) format DVD title, please change the format to Letterbox(LBX) in the projector OSD.
****** Page 37 ****** 9 10 11 Image is too small or too large Image has slanted sides Image is reversed 27 Adjust the zoom ring on the top of the projector. Move the projector closer to or further from the screen Press “MENU” on the remote control or on the control panel. Go to ” Image –> Aspect Ratio” and try different settings. If possible, reposition the projector so that it is centered on the screen. Press the “Keystone” on the OSD until the sides are vertical. Select “Image –> Projection” on the OSD and adjust the projection direction. Problems with the Projector Condition The projector stops responding to all controls Solution If possible, turn off the projector, then unplug the power cord and wait at least 30 seconds before reconnecting power.
****** Page 38 ****** 28 OSD Messages Condition Message Message Reminder Fan Fail – the system fan is not working Fan Fai Lamp Will automatical y turn off soon. Projector Overheated – the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Projector Overheated, Lamp will automatical y turn off soon.
****** Page 39 ****** LED & Alarm Definition Listing LED Messages Message Input Power Plug Standy by Power buttom on Lamp retry Power off (cooling State) Power button OFF; Cooling completed; Standby Mode) Error (Thermal fail) Error (Fan Lock) Erro (Lamp Break down) Meun BLUE ON Isec then off Lamp (UP/Down LED) BLUE Flash On to OFF IOOms ON Isec then off ON Temp (Left/Right LED) BLUE Flash On to OFF IOOms ON Isec then off ON Quick Flashing Power LED RED Flash On to OFF IOOms ON Quick Flashing ON 29 Power LED BLUE ON Qu ick Flashing ON ON ON Note: When power on, click any key, Menu/Up/Down/Left/Right key LED will all be trigger.
****** Page 40 ****** 30 Specifications The specifications listed below are subject to change without notice. For final specs, please refer to Acer’s published marketing specifications. Projection system Resolution Computer compatibility Video compatibility Aspect ratio Displayable colors Projection lens Projection screen size (diagonal) Projection distance Throw ratio Horizontal scan rate Vertical refresh scan rate Keystone correction Weight Dimensions (W x D x H) Power supply Power consumption Operating temperature 1/0 connectors DLP@ WXGA (1280 x 800) IBM PC and compatibles, Apple Macintosh, iMac and VESA standards: SXGA, XGA, SVGA, VGA, WXGA NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/ K/KI/L), HDTV (720p, 1080i, 1080p), EDTV (480p, 576p), SDTV (480i, 576i) Full, 4:3, 16:9, L.Box 16.7 million colors YMIOI, fixed lens, F/2.O 30″ (0.76 m) – 80″ (2.03 m) 3.18′ (0.97 m) -8.46′ (2.58 m) 30k- 100 kHz 50 – 120 Hz +/- 40 degrees 0.43 Kg (0.95 lbs) 140 mm x 116 mm x 41 mm (5.51″ x4.57″ x 1.61″) AC 100 – 240 V, 50-60 Hz Normal mode: 51.5 W +/- 20% @ 110Vac (Bright mode @ full power) ECO mode: 42 W +/-20% @ 1 IOVac (Video mode @ eco power) Standby < 0.5 W 50C to 350C / 4 IOF to 950F DC input xl Micro SD xl USB xl: for multimedia HDMI xl Un iversal input xl AudioNideo input xl ****** Page 41 ****** 31 Standard package contents Power cord xl AC to DC power adapter xl 3.5 mm jack AN cable xl Un iversal to D-sub and Audio out cable xl Remote control xl Battery x 1 (for remote control) User's Gu ide (CD-ROM) xl (for projector function) User's Guide (CD-ROM) xl (for multi-media function) Qu ick start guide xl * Design and specifications are subject to change without notice. ****** Page 42 ****** 32 Compatibility modes A. VGA Analog 1 VGA Analog – PC Signal Modes VGA SVGA XGA SXGA QuadVGA SXGA+ PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 i Mac DV (G3) Resolution 640×480 640×480 640×480 640×480 640×480 800×600 800×600 800×600 800×600 800×600 800×600 1024×768 1024×768 1024×768 1024×768 1024×768 1152×864 1152×864 1 152×864 1280×1024 1280×1024 1280K 1024 1280×960 1280×960 1400×1050 640×480 640×480 800×600 1024×768 1152×870 1280×960 1024×768 V.Frequency [Hz] 60 72 75 85 120 56 60 72 75 85 120 60 70 75 85 120 70 75 85 60 72 75 60 75 60 60 66.6 (67) 60 60 75 75 75 H.Frequency [KHz] 31.5 37.9 37.5 43.3 61.9 35.1 37.9 48.1 46.9 53.7 77.4 48.4 56.5 60.0 68.7 99.0 63.8 67.5 77.1 64.0 77 .o 80.0 60.0 75.2 65.3 3 1.4 34.9 37.9 48.4 68.7 75.0 60.0 ****** Page 43 ****** 2 3 1 VGA Analog – Extended Wide timing Modes WXGA WSXGA+ VGA Analog Modes 480i 576i 480p 576p 720p nop 1080i 1080i 1080p 1080p Resolution 1280×768 1280×768 1280×768 1280×720 1280×800 1440×900 1680×1050 x (Red uced V.Frequency [Hz] Blanking Timing 1366×768 Component Signal 60 75 85 60 60 60 60 60 60 B. HDMI Digital HDMI – PC Signal Modes VGA SVGA Resolution 720×480 720×576 720×480 720×576 1280×720 1280×720 1920K 1080 1920×1080 1920K 1080 1920×1080 Resolution 640×480 640×480 640×480 640×480 640×480 800×600 800×600 800×600 800×600 800×600 800×600 V.Frequency [Hz] 59.94(29.97) 50(25) 59.94 50 60 50 60 (30) 50 (25) 60 50 LFrequency [Hz] 60 72 75 85 120 56 60 72 75 85 120 33 H.Frequency [KHz] 47.8 60.3 68.6 44.8 49.6 59.9 65.3 66.6 47.7 H.Frequency [KHz] 15.7 15.6 31.5 31.3 45.0 37.5 33.8 28.1 67.5 56.3 H.Frequency (KHz] 31.5 37.9 37.5 43.3 61.9 35.1 37.9 48.1 53.7 77.4 ****** Page 44 ****** 34 2 XGA SXGA QuadVGA SXGA+ PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 i Mac DV (G3) 1024×768 1024×768 1024×768 1024×768 1024×768 1152×864 1 152×864 1152×864 1280×1024 1280K 1024 1280×1024 1280×960 1280×960 1400×1050 640×480 640×480 800×600 1024×768 1152×870 1280×960 1024×768 HDMI – Extended Wide timing Modes WXGA WSXGA+ Resolution 1280×768 1280×768 1280×768 1280×720 1280×800 1440×900 1680×1050 1920×1080 (Reduced Blanking Timin ) 1366×768 60 70 75 85 120 70 75 85 60 72 75 60 75 60 60 66.6 (67) 60 60 75 75 75 V.Frequency [Hz] 60 75 85 60 60 60 60 60 60 48.4 56.5 60.0 68.7 99.0 63.8 67.5 64.0 77.0 80.0 60.0 75.2 65.3 31.4 34.9 37.9 48.4 68.7 75.0 60.0 H.Frequency [KHz] 47.8 60.3 68.6 44.8 49.6 59.9 65.3 66.6 47.7 ****** Page 45 ****** 3 HDMI Video Signal Modes 480i 576i 480p 576p 720p 720p 1080i 1080i 1080p 1080p rap IC source monitor range limits Resolution 720×480(1440×480) 720×576(1440×576) 720×480 720×576 1280×720 1280×720 1920×1080 1920×1080 1920×1080 1920×1080 Horizontal scan rate: Vertical scan rate: Max. pixel rate V.Frequency [Hzl 59.94 (29.97) 50 (25) 59.94 50 60 50 60 (30) 50 (25) 60 50 30k-100kHz 50-120Hz 150MHz 35 H.Frequency [KHz] 15.7 15.6 31.5 31.3 45.0 37.5 33.8 28.1 67.5 56.3 ****** Page 46 ****** 36 Regulations and safety notices FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the device and receiver. Connect the device into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/television technician for help Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Notice: Peripheral devices Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this device. Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003. ****** Page 47 ****** 37 Remarque Ilintention des utilisateurs canadiens Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries Acer hereby declares that this projector series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Compliant with Russian regulatory certification ME61 UA.TR.002 Radio device regulatory notice Note: The regulatory information below is for models with wireless LAN and/or Bluetooth only. General This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules). Canada — Low-power license-exempt radio communication devices (RSS-210) a b Common information Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Operation in 2.4 GHz band To prevent radio interference to the licensed service, this device is intended to be operated indoors and installation outdoors is subject to licensing. List of applicable countries Th is device must be used in strict accordance with the regu lations and constraints in the country of use. For further information, please contact the local office in the country of use. Please see ec.europa.eu/enterprise/rtte/implem.htm for the latest country list. ****** Page 48 ****** Acer Incorporated 8F. 88, sec. 1. Xintai 5th Xizhi, New Taipei City 221, Taiwan, R.O.C. Declaration of Conformity we, Acer Incorporated 8F, 88, Sec. 1, Xintai 5th m, Xizhi, New Taipei City 221,Taiwan, R.O.C. Contact Person: Mr. Easy Lai, And, Acer Italy s.r.l Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921, Fax: +39-02 9399-2913, acer.it Hereby declare that: Product: Trade Name: Model Number: Machine Type: Projector Acer cwX1013 K130/L220/LK-W11 Is compliant with the essential requirements and other relevant provisions of the following EC directives, and that all thc necessary steps have taken and are in force to assure that production units of the same product will continue comply with the requirements. EMC Directive 2004/108/EC as attested by conformity with the following harmonized standards: EN55022, AS/NZS CISPR22, Class B – EN55024 EN61000-3-2 Class A – EN61000-3-3 Low Voltage Directive 2006/95/EC as attested by conformity with thc following harmonized standard: – EN60950-1 RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment – Thc maximum concentration valucs ofthe restricted substances by weight in homogenous mater'ial are: Lead Mercu 0.1% Hexavalent Chromium O. I % POI brominated Bi hen Is BB's POI brominated Di hen I Ethers PBDE's Cadmium 0.1% 0.1% 0.01% Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign requirements for energy-related product. ****** Page 49 ****** acer Acer Incorporated 88, sec 1. Xintai 5th Xizhi, New Taipei City 221, Taiwan, R.O.C. The standards listed below are applied to the product if built with WLAN module or wireless keyboard and mouse. ceo R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard: e Article 3.1(a) Health and Safety – EN60950-1 . EN62311 • Article 3.1(b) EMC . EN301 489-1 – EN301 489-17 • Article 3.2 Spectrum Usages EN300 328 EN301 893 (Applicable to 5GHz high performance RLAN). Year to begin affixing CE marking 2011. asy al anagcr Regulation Center, Acer Inc. Dec. 10 2011 Date ****** Page 50 ****** acer Acer America Corporation 333 West San Carlos St., San Jose CA 951 10, U. S. A. Tel : 254-298-4000 Fax 254-298-4147 acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following local Manufacturer / Importer is responsible for this declaration: Product: Model Number: Machine Type: Name of Responsible Party: Addrcss of R(sponsible Party: Contact Person: Phone No.: Fax No.: DLP Projector CWX1013 K130/L220/LK-W11 Acer America Corporation 333 West San Carlos St. San Jose, CA 95110 Acer Representative 254-298-4000 254-298-4147
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL