Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** Acer Projector P7505/F155/PF-807/P7605/F165/PF- WU07/H9505BD/E255D/HE-822J/ P7305W/F125/PF-W07 Series User’s Guide
****** Page 2 ****** Copyright 0 2013. Acer Incorporated. All Rights Reserved. Acer Projector User’s Guide Original Issue: 11/2013 Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of th is manual or supplementary documents and publications. Th is company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particu lar purpose. Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your projector. All correspondence concerning your un it shou ld include the serial number, model number and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electron ically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated. Model number: Serial number Date of purchase: Place of purchase: Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies’ product names or trademarks are used herein for identification purposes only and belong to their respective companies. HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. I”
****** Page 3 ****** iii Information for your safety and comfort Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning Caution for plug as disconnecting device Observe the following guidelines when connecting and disconnecting power to the external power supply unit: Install the power supply unit before connecting the power cord to the AC power outlet. Unplug the power cord before removing the power supply unit from the projector. If the system has multiple sources of power, disconnect power from the system by unplugging all power cords from the power supplies. Caution for Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet. Warnings! Do not use this product near water. Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged. Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.
****** Page 4 ****** To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface. Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, lamp. Using electrical power This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord. If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip’s input rating This product’s AC adapter is equipped with a three-wire grounded plug The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the AC adapter plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details. Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury. Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product. Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length.
****** Page 5 ****** Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel when: the power cord or plug is damaged, cut or frayed liquid was spilled into the product the product was exposed to rain or water the product has been dropped or the case has been damaged the product exhibits a distinct change in performance, indicating a need for service the product does not operate normally after following the operating instructions Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Warning! For safety reasons, do not use non-compliant parts when adding or changing components. Consult your reseller for purchase options. Your device and its enhancements may contain small parts. Keep them out of the reach of small children. Additional safety information Do not look into the projector’s lens when the lamp is on. The bright may hurt your eyes. Turn on the projector first and then signal sources Do not place the product in following environments: Space that is poorly ventilated or confined. At least 50cm clearance from walls and free flow of air around the projector is necessary. Locations where temperatures may become excessively high, such as inside of a car with all windows rolled up Locations where excessive hum idity, dust, or cigarette smoke may contam inate optical components, shortening the life span and darken ing the image. Locations near fire alarms. Locations with an ambient temperature above 40 oc/104 OF. Locations where the altitudes are higher than 10000 feet. Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector. It
****** Page 6 ****** VI might cause fire or electric shock. In this case, unplug immediately and contact your dealer. Do not keep using this product to break or drop it. In this case contact your dealer for inspection. Do not face the projector lens to the sun. It can lead to fire. When switching the projector off, suggest to ensure the projector completes its cooling cycle before disconnecting power. Do not frequently turn off the main power abruptly or unplug the projector during operation. The best way is to wait for the fan to turn off before turning main power off. Do not touch air outlet grille and bottom plate which becomes hot. Clean the air filter frequently if have. The temperature inside may rise and cause damage when the filter/ventilation slots clogged with dirt or dust. Do not look into the air outlet grille when projector is operating. It may hurt your eyes. Always open the lens shutter or remove the lens cap when the projector is on. Do not block the projector lens with any object when the projector is under operation as this could cause the object to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press HIDE on the remote control. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. It could cause it to break on rare occasions. Never replace the lamp assembly or any electronic components unless the projector is unplugged. The product will detect the life of the lamp itself. Please be sure to change the lamp when is showing warning message. When changing the lamp, please allow unit to cool down, and follow all changing instructions. Reset the “Lamp Hour Reset” function from the Onscreen display ” Management” menu after replacing the lamp module. Do not attempt to disassemble this projector. There are dangerous high voltages inside which may hurt you. The only user serviceable part is the lamp which has its own removable cover. Refer servicing only to suitable qualified professional service personnel Do not stand the projector on end vertically. It may cause the projector to fall over, causing injury or damage. This product is capable of displaying inverted images for ceiling mount installation. Only use acer ceiling mount kit for mounting the projector and ensure it is securely installed
****** Page 7 ****** vii Caution for Listening To protect your hearing, follow these instructions. Increase the volume gradually until you can hear clearly and comfortably. Do not increase the volume level after your ears have adjusted Do not listen to music at high volumes for extended periods. Do not increase the volume to block out noisy surroundings. Decrease the volume if you can ‘t hear people speaking near you. Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit acer-group.com/public/Sustainability/index.htm Mercury advisory For projectors or electronic products containing an LCD/CRT monitor or display: “Lamp(s) contain Mercury, Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the Electronic Industries Alliance at eiae.org. For lamp-specific disposal information, check lamprecycle.org
****** Page 8 ****** VIII First things first Usage Notes Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don’t: Block the slots and openings on the unit provided for ventilation. Use abrasive cleaners, waxes or solvents to clean the unit. Use under the following conditions: In extremely hot, cold or humid environments. In areas susceptible to excessive dust and dirt. Near any appliance that generates a strong magnetic field. Place In direct sunlight. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s guide to maximize the life of your unit. Warning: Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes. To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Please do not open or disassemble the product as this may cause electric shock. When changing the lamp, please allow unit to cool down, and follow all changing instructions. This product will detect the life of the lamp itself. Please be sure to change the lamp when it shows warn ing messages. Reset the “Lamp Hour Reset” function from the Onscreen display ” Management” menu after replacing the lamp module. When switching the projector off, please ensure the projector completes its cooling cycle before disconnecting power. Turn on the projector first and then the signal sources. Do not use lens cap when projector is in operation. When the lamp reaches the end of its life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp ‘I .
****** Page 9 ****** Information for your safety and comfort First things first Usage Notes Precautions Introduction Product Features Package Overview Projector Overview Projector Outlook Control Panel Remote Control Layout Getting Started Connecting the Projector Turning the Projector On/Off Turning on the Projector Turning the projector off Adjusting the Projected Image Adjusting the Height of Projected Image How to optimize image size and distance How to get a preferred image size by adjusting distance and zoom How to get a preferred image position by adjusting lens shift User Controls Installation menu Onscreen Display (OSD) Menus Color I ma ge Setting Management Audio 3D Language iii viii VIII VIII 1 3 4 4 6 7 9 9 11 11 12 13 13 14 17 20 23 23 25 26 28 30 33 34 35 36
****** Page 10 ****** Appendices Troubleshooting LED & Alarm Definition Listing Cleaning and replacing the dust filters Replacing the Lamp Ceiling Mount Installation Specifications Compatibility modes Regulations and safety notices 37 37 41 42 43 44 47 50 54
****** Page 11 ****** 1 Introduction Product Features This product is a single-chip DLP@ projector. Outstanding features include: DLP@ technology P7305W/F125/PF-W07 series: True 1280×800 WXGA resolution P7505/F155/PF-807/H9505BD/E255D/HE-822J series: True 1920×1080 1080p resolution P7605/F165/PF-WU07 series: True 1920×1200 WUXGA resolution Full/4:3/16:9/L.Box aspect ratio supported Acer ColorBoost technology delivers nature’s true colors for vivid, life-like images Acer Color Safe II technology ensures consistent color rendition over time Enables projecting 3D content via DLP Link Technology: Blue-Ray 3D supported and Nvidia 3DTV Play Ready Enrichs 3D experience for 2D contents via 2D to 3D convert function High brightness and contrast ratio Versatile display modes (Bright, Presentation, Standard, Video, Movie, Dark Cinema, Game, Sports, User) enable optimum performance in any situation NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported Side-sliding lamp design allows easy lamp replacement Lower power consumption and economy (ECO) mode extends lamp life Acer EcoProjeciton Technology delivers Intelligent power management approach and physical efficiency improvement Equipped with HDMITM connection supporting HDCP Advanced digital keystone correction optimizes presentations Smart detection delivers quick, intelligent source detection Multi-language on screen display (OSD) menus Full-function remote control Manual focus projection lens zooms up to 1.5x 2x digital zoom and pan move function
****** Page 12 ****** 2 Microsoft@ Windows 2000, XP, Vista compliant Manual lens shift adjustment , Windows 7, Windows @ 8, os Note: Functions vary depending on model definition.
****** Page 13 ****** 3 Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if any thing is missing Projector with lens cap Composite video cable 6Øåd o ooa 0600 0800 o oo Remote control (option) Carrying case User’s guide (for multi-media and wireless functions) Power cord Acer Projector Security Card Security card Proi Qu ick start guide USB WiFi adapter (option) P’rgie:tor Qu ick start guide (for multi-media and wireless functions) VGA cable User’s gu ide 2 x Batteries (option) Dust filter (option)
****** Page 14 ****** 4 Projector Overview Projector Outlook Front / upper side 3 2 2 3 4 5 Description Lens cap Zoom lever Zoom Lens Focus ring Remote control receivers 4 5 6 7 8 9 10 8 9 5 10 7 6 Description Elevator feet Tilt adjusting wheels Control panel Power button Lens shift control rings
****** Page 15 ****** Rear side 2 3 4 1 5 6 7 5 11 12 1314 1 2 3 4 5 6 7 8 9 10 8 15 11 12 13 14 15 16 17 18 19 20 9 16 10 00 17 o 18 19 20 Description Power socket LAN (RJ45 Port for 101100M Ethernet) Mini USB Ctrl connector (for firmware upgrade and USB display) USB A1 connector USB A2 connector (supports USB wireless adapter) HDMI 3 connector HDMI I/HDMI 2 connector (supports 2D to 3D feature) PC analog signal/HDTV/SCART/compo- nent video input connector (VGA IN 1) Mon itor loop-through output connec- tor (for VGA IN 1 only) S-Video input connector Description Composite video input connector Audio input 1 connector (VGA IN INGA Audio output connector 12V DC output connector PC analog input connector (VGA IN 2) RS232 connector YPbPrNCbCr input connector Audio input 2 connector (Component/ Composite/S-Video) Wired IR remote input connector KensingtonTM lock port Note: Functions vary depending on model definition.
****** Page 16 ****** 6 Control Panel 1 2 3 10 MENU 6 8 Ziff—9 2 Description 2 3 4 5 6 7 8 9 10 Icon BACK d) ENTER Function LAMP KEYSTONE Back/Stop MENU POWER SOURCE TEMP Four directional select keys Enter/Play/Pause IR Recevier Lamp Indicator LED Adjusts the image to compensate for distortion caused by tilting the projector. Press “Back/Stop ” to stop playing media file or go back to upper data folder. • Press ” MENU” to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu. • Confirm your selection of items. See the contents in “Turning the Projector On/ Off” section. Press “SOURCE” to choose RGB, Component, S- Video, Composite, SCART, HDTV and HDMITM sources. Temp Indicator LED Use to A < select items or make adjustments to your selection. Press " Enter/Play/Pause" to play/pause media file. Remote control receiver. ****** Page 17 ****** Remote Control Layout Rating ocgv C CFC LIC ++1 II COI VC..JF211 co 1 5 8 10 12 14 16 – 18 19 21 22 25 29 31 nct10 *OWEN vou 2 4 7 11 13 15 17 20 23 24 26 28 30 33 • •.wc•eo *nor.' sau PAGE öööö öÜöö 0000 32 8 7 17 23 2 3 4 5 6 7 8 9 10 II 12 13 14 In rare transmitter Laser pointer POWER HIDE FREEZE MEDIA SETUP SOURCE ZOOM Bac Laser utton Enter Four directional select keys KEYSTONE escnptl n Sen s signa stot e projector. Aim the remote at the viewing screen. Please see "Turning t e Projector On/O " section. Temporarily turns off the video. Press "HIDE" to hide the image, press again to display the image. Pause the screen image. Press "MEDIA to enter me la OSD setting C angest e active source. Press "31)" to se ect 3D mo e s. Zooms t e projector Isp ay In or out. Press "BACK" to go ac one menu step. Aim t e remote att e Viewing screen, press an o button to activate the laser pointer. This function is not supported in Japanese market. Press "ENTER" to play media file. Use up, down, left, right buttons to select items or make adjustments to your selection. Adjusts the image to compensate for distortion caused by tilting the projector (± 40 degrees). ****** Page 18 ****** 8 15 16 17 18 19 20 22 23 24 25 26 27 28 29 30 31 32 33 34 con un MENU Ion MOUSE Left/ Right Click 00 MOUSE_Four directional select keys MODE 8 VOLUME +/- 00 PAGE prev Next P ay/Pause Stop VGA S-VIDEO INFO COMPONENT VIDEO SD/USB A USB B HDMITM/DVI LANWiFi KeyPad ASPECT RATIO RESYNC MEDIA HOME escri tion Press "MENU" to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu. Confirm your selection of items. Left-fright-click buttons are on the left and right, respectively; the center button works as a multidirectional pointer stick. To enable this function, an USB cable must be connected to projector from your PC. Press "MODE" to select the display mode. Increases/ ecreasest evo ume. For computer mo eon y. Use t IS utton to se ectt e next or previous page. This function is on ly available when connected to a computer via a USB cable. Press "Prev" to go to previous index or page in file list view. Press "Next" to go to next In exor page In I e ISt View. Press "P ay ause" to p ay/pause me la I e. Press " top" to stop p ayqng me la I e. Press "VGA" to change source to the VGA connector. Th is connector supports analog RGB, YPbPr (480p/576p/720p/ 1080i), YCbCr (480i/576i) and RGBsync. Toc ange source to S-VI eo. Press "INFO" to Isp ay me la In ormatlon. Press "COMPONENT" to c ange source to Component video. Th is connection supports YPbPr (480p/576p/720p/ 1080i) and YCbCr (480i/576i). To c ange source to COMPOSITE VIDEO. Press D USB A" to ange source to USB A. no SD function) Press "USB B" to ange source to USB B. Press "HDMITM/DVI" to ange source to HDMITM no DVI function). Press "LAN/WiFi" to display the image which is wire or wirelessly transmitted from the PC to the projector via the " Acer LAN webpage management" utility. (Acer Projector Multimedia CD) Press "0-9" to input a password in the "Security" . Choose the desired aspect ratio. Automatically synchronizes the projector to the input source. Press "HOME" to return tot e ome page o me la mo e. Note: Functions vary depending on model definition. ****** Page 19 ****** Getting Started Connecting the Projector Internet usB DVD player 9 S-Video Output 8 Video Output 2 5 6 7 IHOW 9 ..ooo • 1 3 4 11 USB 11 Description 1 2 3 4 5 6 7 8 5 t 10 RS232 9 10 11 12 13 14 15 QOO ooe SOOO o tiff i 13 14 12 11 9 Power cord LAN cable USB cable HDMI cable VGA cable S-Video cable Composite video cable Audio cable jack/jack DVD player, Set-top Box, HDTV receiver Description Audio cable Jack/RCA VGA to component/HDTV adapter 3 RCA component cable RS232 cable Audio cable jack for wired remote 12V DC cable Mouse USB disk/stick USB WiFi adapter ( for USB A2 only) ****** Page 20 ****** 10 Note: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector. "*JJ USB drive limitation, do not support power Note: consumption over 500mA. Please have external power for USB device. Note: To enable wireless function, the USB wireless adapter must be plugged into the USB A2 port. Note: Functions vary depending on model definition. ****** Page 21 ****** 11 Turning the Projector On/Off Turning on the Projector 1 2 3 4 Remove the lens cap.(lllustration #1) Ensure that the power cord and signal cable are securely connected. The Power indicator LED will flash red. Turn on the projector by pressing "Power" button on the control panel, and the Power indicator LED will turn blue.(lllustration #2) Turn on your source (computer, notebook, video player ,etc.). The projector will detect your source automatically. If the screen displays " Lock" and "Source" icons, it means the projector is locked onto a specific source type and there is no such type of input signal detected If the screen displays " No Signal", please make sure the signal cables are securely connected. If you connect to multiple sources at the same time, use the "Source" button on either control panel or the remote control or direct source key on the remote control to switch between inputs. 2 Power button 1 Lens cap ****** Page 22 ****** 12 Turning the projector off 1 2 3 4 5 To turn the projector off, press the power button. This message appears: " Please press the power button again to complete the shutdown process. Press the power button again. The LED power indicator will turn RED and blink rapidly after the projector is turned off, and the fan(s) will continue to operate for about 2 minutes to ensure that the system cools properly. (only supported under "lnstant Resume" mode) As long as the power cord remains plugged in, you can press the power button to turn the projector immediately back on anytime during the 2- minute shutdown process. (only supported under "lnstant Resume" mode) Once the system has finished cooling, the LED power indicator will stop blinking and turn solid red to indicate standby mode. It is now safe to unplug the power cord. Warning indicators: "Please press the power button again to complete the shutdown process. " This onscreen message indicates that the projector has overheated. The lamp with automatically turn off, the projector will automatically shut down, and the LED temp indicator will turn solid red. Contact your local dealer or service center. "Fan failed. Lamp will automatically turn off soon." This onscreen message indicates that the fan has failed. The lamp will automatically turn off, the projector will automatically shut down, and the LED temp indicator will blink. Contact your local dealer or service center. Note: Whenever the projector automatically shuts down and the LED lamp indicator turns solid red, contact your local reseller or service center. ****** Page 23 ****** 13 Adjusting the Projected Image Adjusting the Height of Projected Image The projector is equipped with elevator feet for adjusting the height of image. To raise/lower the image: 1 2 3 Raise the image to the desired height angle (Illustration #1), then pull out the stand feet into position. Use Tilt adjusting wheel (Illustration #2) to fine-tune the display angle. Use Lens shift control rings to move the image to the ideal position. (refer to page 20) acer I Elevator feet 2 Tilt adjusting wheels o ****** Page 24 ****** 14 How to optimize image size and distance Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen. WUXGA series If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 41" and 62" Note: Remind as below figure, the space of 100 cm height is required when located at 2.0 m distance. Screen size ax screen size 2.0 m Desired Dista nce Top 41n 66 c Screen size Height: 1 Ocm from bas to top of im ge Top Desired Distance (m) 1.5 2 2.5 3 3.5 4 4.5 5 6 7 8 9 10 12 (Min zoom) (Max zoom) rom asetotop 'agona rom ase to top of image (cm) 49 66 82 99 115 132 148 165 197 230 263 296 329 362 395 Zoom Ratio: lagona (inch) 31 41 51 61 71 81 92 102 122 143 163 183 204 224 244 1.5x W (cm)x H (cm) 66K 41 88 x 55 110 x 69 132 x 82 154 x 96 176 x 110 197 x 123 219 x 137 263 x 165 307 x 192 351 x 219 395 x 247 439 x 274 483 x 302 527 x 329 (inch) 47 62 78 93 109 124 140 155 186 218 249 280 311 342 373 W (cm) x H (cm) 100 x 63 134 x 84 167 x 105 201 x 126 234 x 146 268 x 167 301 x 188 335 x 209 402 x 251 469 x 293 535 x 335 602 x 377 669 x 418 736 x 460 803 x 502 of image (cm) 75 100 126 151 176 201 226 251 301 351 402 452 502 552 602 ****** Page 25 ****** 15 1080p series If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 40" and 60" Note: Remind as below figure, the space of 98 cm height is required when located at 2.0 m distance. screen Size 2.0 m Desired Distance 40B H ight Height: 98 from base t top of imag Top Desired Distance Screen size (Min zoom) Top Screen size (Max zoom) From base to (m) Diagonal W (cm) x 1.5 2 2.5 3 3.5 4 4.5 5 6 7 8 9 10 12 (inch) 30 40 50 59 69 79 89 99 119 139 159 178 198 218 238 66 x 37 88 x 49 110 x 62 132 x 74 154 x 86 176 x 99 197 x 111 219 x 123 263 x 148 307 x 173 351 x 197 395 x 222 439 x 247 483 x 272 527 x 296 top of image (cm) 48 64 80 96 112 128 144 160 193 225 257 289 321 353 385 Diagonal (inch) 45 60 76 91 106 121 136 151 181 212 242 272 302 333 363 W (cm) x 110×56 134 x 75 167 x 94 201 x 113 234 x 132 268 x 151 301 x 169 335 x 188 402 x 226 469 x 264 535 x 301 602 x 339 669 x 377 736 x 414 803 x 452 From base to top of image (cm) 73 98 122 147 171 196 220 245 294 343 392 441 489 538 587 Zoom Ratio: 1 5x
****** Page 26 ****** 16 WXGA series If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 39″ and 59″ Note: Remind as below figure, the space of 104 cm height is required when located at 2.0 m distance. a *screen size screen size 2.0 m Desired Distance 39, Height: 104 from base t Heig t: /top of imag 68 Screen size Top Screen size (Max zoom) Top Desired Distance (m) Diagonal (Min zoom) From base to 1.5 2 2.5 3 3.5 4 4.5 5 6 7 8 9 10 12 (inch) 29 39 49 58 68 78 87 97 117 136 155 175 194 214 233 W (cm) x 63 x 39 84 x 52 105 x 65 125 x 78 146 x 91 167 x 105 188x 118 209 x 131 251 x 157 293 x 183 334 x 209 376 x 235 418 x 261 460 x 287 502 x 314 top of image (cm) 51 68 85 102 119 136 153 170 204 238 272 306 340 374 408 Diagonal (inch) 59 74 89 104 118 133 148 178 207 237 266 296 325 355 W (cm) x 96 x 60 127 x 80 159K 100 191 x 120 223K 139 255 x 159 287 x 179 319K 199 382 x 239 446 x 279 510K 319 574 x 359 637 x 398 701 x 438 765 x 478 From base to top of image (cm) 78 104 129 155 181 207 233 259 311 362 414 466 518 570 621 Zoom Ratio: 1 5x
****** Page 27 ****** 17 How to get a preferred image size by adjusting distance and zoom The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring WUXGA series To obtain an image size of 60″ set the projector at a distance 1.9 m and 2.9 m from the screen. Desired image size 2.9 m c Desired Image Size 1.9nY Desired Distance Distance (m) Diagonal (inch) Max zoom Min zoom 30 40 50 60 70 80 90 100 120 150 180 200 250 300 Zoom Ratio: W (cm) x H (cm) 65 x 40 86 x 54 108 x 67 129 x 81 151 x 94 172x 108 194x 121 215x 135 258x 162 323 x 202 388 x 242 431 x 269 538 x 337 646 x 404 1.5x 1.0 1.3 1.6 1.9 2.3 2.6 2.9 3.2 3.9 4.8 5.8 6.4 8.0 9.7 1.5 2.0 2.5 2.9 3.4 3.9 4.4 4.9 5.9 7.4 8.8 9.8 12.3 Height: 97 m from base tot p of image Top (cm) From base to top of mage 48 65 81 97 113 129 145 162 194 242 291 323 404 485
****** Page 28 ****** 18 1080p series To obtain an image size of 60″ from the screen. set the projector at a distance 2.0 m and 3.0 m Desired image size 3.0 m Desired Image Size f.om Desired Distance Distance (m) Diagonal (inch) 30 40 50 60 70 80 90 100 120 150 180 200 250 300 Zoom Ratio: W (cm) x H (cm) 66 x 37 89 x 50 111 x 62 133 x 75 155 x 87 177 x 100 199x 112 221 x 125 266x 149 332 x 187 398 x 224 443 x 249 553×311 664 x 374 Max zoom 2.0 2.3 2.6 3.0 3.3 4.0 5.0 6.0 6.6 9.9 Min zoom 2.0 2.5 3.0 3.5 4.0 4.5 5.0 7.6 10.1 12.6 Height: 97 m from base tot p of image Top (cm) From base to top of mage 49 65 97 113 130 146 162 194 243 291 324 405 486 1.5x
****** Page 29 ****** WXGA series To obtain an image size of 60″ from the screen. 19 set the projector at a distance 2.0 m and 3.1 m Desired image size 3.1m Desired Image Size ä.om Desired Distance Distance (m) Diagonal (inch) 30 40 50 60 70 80 90 100 120 150 180 200 250 300 Zoom Ratio: W (cm) x H (cm) 65 x 40 86 x 54 108 x 67 129 x 81 151 x 94 172 x 108 194x 121 215 x 135 258x 162 323 x 202 388 x 242 431 x 269 538 x 337 646 x 404 Max zoom 2.0 2.4 2.7 3.0 3.4 5.1 6.8 10.1 Min zoom 2.6 3.6 4.6 5.2 6.2 7.7 9.3 10.3 12.9 Height: 10 cm from base tot p of Image Top (cm) From base to top of mage 53 70 88 105 123 140 158 175 210 263 315 350 438 525 1.5x
****** Page 30 ****** 20 How to get a preferred image position by adjusting lens shift The projector is equipped with lens shift for adjusting the position of projected image right and left or up and down without requiring you to physically move the projector. LENS SHIFT Vertical Lens Shift ring Horizontal Lens Sh ift ring LENS SHIFT Note: The figures shown in this section are for reference only not approximate value. The figures between un its can be different due to assembly toleran ce.
****** Page 31 ****** 21 Adjusting the horizontal or vertical image position WUXGA series The vertical image height can be adjusted 20% of the image height With the lens in the centre position the horizontal image position can be adjusted to the left or right by up to a maximum of 15% of the image width. 00/0(H) 1000/0(V) H x 15% Offset max= Offset min= V x 5% H x 15%
****** Page 32 ****** 22 WXGA/1080p series The vertical image height can be adjusted between 5% and 30% of the image height. (The minimum vertical image offset is fixed at 5% of the image height above the centre of the projector lens.) With the lens in the centre position the horizontal image position can be adjusted to the left or right by up to a maximum of 15% of the image width. 00/0(H) 1200/00/) 1050/00/) -150/0(H) v x 25% Offset max= Offset min= V x 5% 150/0(H) H x 15%
****** Page 33 ****** 23 User Controls Installation menu The installation menu provides an onscreen display (OSD) for projector installation and maintenance. Use the OSD only when the message “No signal input” is displayed on the screen. The menu options include settings and adjustments for screen size and distance, focus, keystone correction and more . 1 2 3 4 Turn on the projector by pressing ” Power” button on the control pad. Press the ” MENU” button on the control pad to launch the OSD for projector installation and maintenance. Installation PTOlacnon Manual Language Reset Sebee•t Press The background pattern acts as a guide to adjusting the calibration and alignment settings, such as screen size and distance, focus and more . The Installation menu includes the following options: •Projection method •Manual Keystone settings •LAN/WiFi settings •LAN IP/ Mask settings •Language settings •Reset to factory default function Use the up and down arrow keys to select an option, the left and right arrow keys to adjust selected option settings, and the right arrow key to enter a submenu for feature setting. The new settings will be saved automatically upon exiting the menu.
****** Page 34 ****** 24 5 Push the menu button anytime to exit the menu and return to the Acer welcome screen. Note: Functions vary depending on model definition.
****** Page 35 ****** 25 Onscreen Display (OSD) Menus The projector has multilingual OSD that allow you to make image adjustments and change a variety of settings. Using the OSD menus To open the OSD menu, press ilMENU” on the remote control or control panel. When the OSD is displayed, use the A v keys to select any item in the main menu. After selecting the desired main menu item, press to enter submenu for feature setting Use the A v keys to select the desired item and adjust the settings by using the keys. Select the next item to be adjusted in the submenu and adjust as described above. Press ” MENU” on the remote control or control panel, the screen will return to the main menu. To exit OSD, press “MENU” on the remote control or control panel again. The OSD menu will close and the projector will automatically save the new settings. Main menu Color Display Mode Wall Color Brightness Contrast Saturation Tint Color Temperature Dynamic Black Gamma Advanced Select Sub menu 50 Adjust Standard Setting press Off press Main Menu ML-NU Note: Some of the following OSD settings may not be available. Please refer to the actual OSD of your projector. Note: Functions vary depending on model definition.
****** Page 36 ****** 26 Color Display Mode Wall color Brightness Contrast Saturation Tint Color Temperature Dynamic Black Gamma There are many factory presets optimized for various types of mages. Bright: For brightness optimization. Presentation: For meeting presentation Standard: For common environment. Video: For playing video in a bright environment. Movie: For brighter and general movie/video/photo playing Dark Cinema: For dark movie content. Game: For game content. Sports: For sport picture. User: Memorize user’s settings. Use th is function to choose a proper color according to the wall. There are several choices, including wh ite, light yellow, light blue, pink, dark green. It will compensate the color deviation due to the wall color to show the correct image tone. Adjust the brightness of the image. Press to darken the image. Press to lighten the image. “Contrast” controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press < to decrease the contrast. Press to increase the contrast. Adjusts a video image from black and white to fu Ily saturated color. Press 0″ increase noise reduction. Black Extension This ensures optimum black level for each analog source. Note: “Saturation and “Tint” functions are not supported under computer or HDMI mode. Note: Functions vary depending on model definition.
****** Page 38 ****** 28 Image Projection Aspect Ratio Manual Keystone Sharpen ess H. Position V. Position Frequency Tracking Front-Desktop: The factory default setting Rear-Desktop: When you select th is function, the projector reverses the image so you can project from behind a translucent screen. Rear-Ceiling: When you select this function, the projector reverses and inverts the image at same time. You can project from behind a translucent screen with ceiling mounted projection. Front-Ceiling: When you select this function, the projector Inverts the image for ceiling-mounted projection. Use this function to choose your desired aspect ratio. Auto: Keep the image with original width-higth ratio and maxi mize the image to fit native horizontal or vertical pixels. Full: Resize image to fit full screen by width (1280 pixels) and height (800 pixels) 4:3: The image will be scaled to fit the screen and displayed using a 4:3 ratio. 16:9: The image will be scaled to fit the width of the screen and the height adjusted to display the image using a 16:9 ratio. L.Box: Keep original signal aspect ratio and zoom in by 1.333 times. Adjust image distortion caused by tilting projection. (±40 degrees) The Manual Keystone function is unavailable under Auto Keystone setting to “On . Adjusts the sharpness of the image. Press Press Press Press Press Press to decrease the sharpness. to increase the sharpness. to move the image left. to move the image right. to move the image down. to move the image up. “Frequency” changes the projector’s refresh rate to match the frequency of your computer’s graphics card. If you can see a vertical flickering bar in the projected image, use this function to make the necessary adjustments. Synchronizes the signal timing of the projector with the graphics card If you experience an unstable or flickering image, use th is function to correct it.
****** Page 39 ****** 29 HDMI Color Range Adjust the color range of the HDMI image data to correct color display error. Auto: Automatically adjust by information from player. Limited Range: Prosess the input image as limited color range data. Full Range: Prosess the input image as full color range data. HDMI Scan Info Adjust the overscan ratio of the HDMI image on screen. Auto: Automatically adjust by information from player. Underscan: Always no overscan on HDMI image. Overscan: Always keep overscan on HDMI image. Note: “H. Position”, “V. Position”, “Frequency” and “Tracking” functions are not supported under HDMI or Video mode. Note: “HDMI Color Range” and “HDMI Scan Info” functions are only supported under HDMI mode. Note: Functions vary depending on model definition.
****** Page 40 ****** 30 Setting Startup Screen Screen Capture Source Lock Closed Caption Auto Screen VGA OUT (Standby) LANIWiFi Reset Use th is function to select your desired startup screen. If you change the setting, the changes will take effect when you exit the OSD menu. • Acer: The default startup screen of your Acer projector. User: Use memorize picture from “Screen Capture” function. Use th is function to customize the startup screen. To capture the image that you want to use as the startup screen, follow the instructions below. Notice: Before proceeding with the following steps, make sure that the ” Keystone” is set to the default value 0 and the aspect ratio is set to 4:3. For details, refer to the ” Image” section. Change the “Startup Screen ” from the default setting “Acer” to ” User” Press “Screen Capture” to customize the startup screen. A dialog box appears to confirm the action. Choose “Yes” to use the current image as your custom ized startup screen. The capture range is the red rectangular area. Choose ” No” to cancel the screen capture and exit the onscreen display (OSD). A message appears, stating that the screen capture is in progress. When the screen capture is finished, the message disappears and the original display is shown. The custom ized startup screen, as shown below, takes effect when there is a new input signal or when you restart the projector. When source lock is turned “off”, the projector will search for other signals if the current input signal is lost. When source lock is turned “on”, it will “lock” the current source channel unless you press “Source” button on the remote control for the next channel. Selects a preferred closed caption ing mode from CCI, CC2, CC3, CC4, (CCI displays captions in the primary language in your area). Select “Off” to turn off the captioning feature. This function is on ly available when a composite video or S-Video input signal is selected and its system format is NTSC. Set your screen aspect ratio to 4:3. Th is function is not available when the aspect ratio is ” 16:9″ or “Auto” . Default is “On the down/up move of electronic screen will be related with power on/off of Projector. Default is “Off” . Choose “On ” to enable VGA OUT connection. LANIWiFi Default is “Off” . Choose “On ” to enable LAN connection. If users want to do LAN control under standby mode, change VGA OUT (Standby) from Off to On. LAN IP/ Mask Identify IP and Mask address. LAN Reset Reset LAN function. Press the button and choose “Yes” to return the parameters on all menus to the factory default settings.
****** Page 41 ****** Security 31 Security Th is projector provides a useful security function for the admin istrator to manage usage of the projector . Press to change the “Security” setting. If the security function is enabled, your must enter the “Admin istrator Password” first before changing the security settings. Select “On ” to enable the security function. The user has to enter a password to operate the projector. Please refer to the ‘User Password” section for details. If “Off” is selected, then the user can turn on the projector without password. Timeout(Min.) Once “Security” is activated to ” On”, the administrator can set timeout function. Press or to select the timeout interval. The range is from 10 minute to 990 minutes. When the time is up, the projector will prompt the user to enter the password again. The factory default setting of “Timeout(Min.)” is “Off” . Once the security function is enabled, the projector will request user to enter password when switch on the projector . Both “User Password” and “Administrator Password” can be accepted for this dialogue. User Password Press to setup or change the ” User Password”. Press number keys to set your password on the remote control and press “MENU” to confirm. Press to delete character. Enter the password when you see ” Confirm Password displayed. The password should be between 4 and 8 characters long. If you select “Request password only when plugging the power cord in.” , the projector will prompt the user to enter the password every tme the power cord is plugged. If you select “Always request password while projector turns on. ‘I, the user has to enter the password every time when the projector is turned on. Administrator Password The “Administrator Password” can be used in both the “Enter Admin istrator Password” and “Enter Password” dialog boxes. Press to change the “Admin istrator Password”. The factory default of “Administrator Password” is ” 1234″ . If you forgot your adm inistrator password, do the following to retrieve the administrator password: An unique 6-digit ” Universal Password” which is printed on the Security Card (please check accessory in the box). Th is un ique password is the number which will be accepted by projector anytime no matter what the Admin istrator Password is. If losing this security card and number, please contact with an Acer service center.
****** Page 42 ****** 32 Lock to user startup screen Defau It Lock User Startup Screen is “Off”. If lock user startup screen is “On ‘l, users cannot change startup screen anymore and avoid other users change that arbitrarily. Choose “Off” to unlock startup screen. Note: Functions vary depending on model definition
****** Page 43 ****** 33 Management ECO Mode High Altitude Turn Off Mode Timer Auto Shutdown Lamp Hour Elapse Lamp Reminding Lamp Hour Reset Choose “On” to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose “Off” to return normal mode. Choose “On” to turn on High Altitude mode. Operate the fans at fu II speed continuously to allow for proper high altitude cooling of the projector. Instant Off: Shuts down the projector without fan cooling. Instant Resume: Resumes the system when the Power button is pressed again within 2 minutes. Start (or Stop) Press to start (or stop) the timer. Period Press < or to adjust the timer period. Alarm Select this function to adjust the notification volume when the timer function is enabled and time is up. Timer Display Choose "On or "Off" to which timer mode to display on the screen. Location Choose the location of the timer on the screen. The projector will automatically shutdown when there is no signal input after the allocated time. (default is 120 minutes) Displays the lamp's elapsed operating time (in hours). Activate this function to display a reminder to change the lamp 30 hours before its expected end-of-life. Press the button and choose "Yes" to turn the lamp hour counter to 0 hours. Note: Functions vary depending on model definition. ****** Page 44 ****** 34 Audio Volume Mute Power On/Off Volume Alarm Volume Press Aspect Ratio” and try different settings. If possible, reposition the projector so that it is centered on the screen. Press the Keystone / ü ” on the control panel or on the remote control until the sides are vertical. Press the ” Keystone” on the OSD until the sides are vertical. Select Image Projection” on the OSD and adjust the projection direction. Problems with the Projector 2 Condition The projector stops responding to all controls Lamp burns out or makes a popping sound Solution If possible, turn off the projector, then unplug the power cord and wait at least 30 seconds before reconnecting power. When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the “Replacing the Lamp” section.
****** Page 50 ****** 40 OSD Messages Condition Message • Message Reminder Fan Fail – the system fan is not working Fan Fail. Lamp will automatically turn of soon. Projector Overheated – the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Please check the following message. Projector overheated, system will turn off automatically soon, please: I, Check If operation amblent temperature between 5 degree and 40 degree, 2. Check if filter needs to be cleaned. 3. Check if inlet or outlet is blocked. 4. Check if high altitude mode is set when the projector operating at high altitude area. Please also check the dust filters if they are installed. If the dust filter is clogged with dust, please clean it. Please refer to “Clean ing and replacing the dust filter” for details. • Replace the lamp – the lamp is about to reach its maximum lifetime. Prepare to replace it soon. Lamp is approaching the end of its useful life in full power operation. Replacement suggested!
****** Page 51 ****** LED & Alarm Definition Listing LED Messages Message Standby (power cord plugged in) Power button ON Lamp retry Turning off (cooling state) Turning off (cooling completed) Error (thermal failure) Error (fan lock failure) Error (lamp breakdown) Error (color Wheel fail) 41 Power LED Lamp LED Red Quick flashing Temp LED Red Quick flashing Red Qu ick flashing Blue Quick flashing
****** Page 52 ****** 42 Cleaning and replacing the dust filters Cleaning the dust filters Clean the dust filters after every 1000 hours of use. If they are note cleaned periodically, they can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. 2 1 Follow these steps: 1 2 3 4 5 6 Turn the projector off. Wait for the Power LED to stop flashing then unplug the power cord Allow the projector at least 30 mins to cool down. Unplug the corner (Illustration #1) Pull out the dust filter (Illustration #2) To clean the dust filters, use a small vacuum cleaner designed for computers and other office equipment. If the dirt is difficult to remove or the filter is broken, please contact your local dealer or service center to obtain a new filter.
****** Page 53 ****** 43 Replacing the Lamp Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp. The projector will detect the lamp life. You will be shown a warning message ” Lamp is approaching the end of its useful life in full power operation. Replacement suggested!” When you see this message, change the lamp as soon as possible. Make sure the projector has been cooling down for at least 30 minutes before changing the lamp. Warning: The lamp compartment is hot! Allow it to cool down before changing the lamp. 1 4 2 To Change the Lamp 1 2 3 4 5 6 7 Turn off the projector by pressing the power button. Allow the projector at least 30 mins to cool down. Disconnect the power cord. Find the “OPEN” button on side of the projector and push it to open the cover. (Illustration #1) Open the cover. (Illustration #2) Remove the two screws that secure the lamp module.(lllustration #3) Pull out the lamp module by force. (Illustration #4) To replace the lamp module, reverse the previous step. Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
****** Page 54 ****** 44 Ceiling Mount Installation If you wish to install the projector using a ceiling mount, please refer to the steps below: 1 Drill four holes into a solid, structurally sound part of the ceiling, and secure the mount base. Note: Screws are not included. Please obtain the appropriate screws for your type of ceiling Secure the ceiling rod using the appropriate type of four-cylinder screws. Ceiling Mount Base – Attach to celling Short Rod Long Rod Extension Rod Long Cylinder Cap Allen Key Screw Type A – For tightening/loosening mm length 8 mm diameter – Tightening Screw Medium Rod
****** Page 55 ****** 3 4 45 Use the appropriate number of screws for the projector size to attach the projector to the ceiling mount bracket. Screw Type B Smaller Washer Large Washer Projector Bracket Supports projector and allows for adjustments To Spacer – For heat dissipation Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution. Use two washers for extra support, if deemed necessary. Attach the ceiling bracket to the ceiling rod Screw Type A 50 mm length/ – 8 mm diameter Large cylinder cap Allen Key – For tightening/loosening Tightening Screw
****** Page 56 ****** 46 5 Adjust the angle and positioning as necessary. 300 Tightening Screw Allen Key 3600 Allen Key Tightening Screw Note: The appropriate type of screw and washer for each model is listed in the table below. 4 mm diameter screws are enclosed in the screw pack. Screw Type B Washer Type Di ameter (mm) 4 Length (mm) 25 Large Small o SCREW SPEC. M4 x 25 mm ‘Elli 140.00mm
****** Page 57 ****** 47 Specifications The specifications listed below are subject to change without notice. For final specs, please refer to Acer’s published marketing specifications. Projection system Resolution Computer compatibility Video compatibility Aspect ratio Displayable colors Projection lens Projection screen size (diagonal) Projection distance Throw ratio Horizontal scan rate Vertical refresh scan rate DLP@ P7305W/F 125/PF-W07 series: True 1280×800 WXGA resolution P7505Æ 155/PF-807/H9505BD/E255D/HE-822J ser ies: True 1920×1080 1080p resolution 165/PF-WU07 series: True 1920×1200 WUXGA resolution Maximum: UXGA (1600 x 1200), WSXGA+ (1680×1050), 1080p (1920×1080), WUXGA-RB (1920 x 1200) IBM PC and compatibles, Apple Macintosh, iMac and VESA standards: SXGA, XGA, VGA, SVGA, SXGA+, WXGA, WXGA+, WSXGA+ NTSC (3.58/443), PAL (B/D/G/H/I/WN), SECAM (B/D/G/ K/KI/L), HDTV (720p, 1080i/p), EDTV (480m 576p), SDTV (480i, 576i) Full, 4:3, 16:9, L Box 1.07 billion colors F = 2.45 2.9, f = 22.18mm 33.27mm, 1:1.5 Manual Zoom and Manual Focus P7305W/F125/PF-W07 series: 29″ (74 cm) 300″ (762 cm) P7505Æ 155/PF-807/H9505BD/E255D/HE-822J ies: 30″ (76cm) 300″ (762cm) 165/PF-WU07: 31″ (78cm) 300″ (762cm) P7305W/F125/PF-W07 series: 4.9′ (1.5 m) 33.31 (10.1 m) P7505Æ 155/PF-807/H9505BD/E255D/HE-822J ser ies: 4.91 (1.5 m) 32.6′ (9.9 m) 165/PF-WU07 series: 4.9′ (1.5m) 31.7′ (9.7m) P7305W/F125/PF-W07 series: 59″ (1.57 2.39:1) P7505Æ 155/PF-807/H9505BD/E255D/HE-822J ies: (1.49 2.28:1) P7605Æ 165/PF-WU07 series: 62 (1.49 2.28:1) 15k IOOkHz 24 – 120 Hz
****** Page 58 ****** 48 Lamp type Keystone correction Audio Weight Dimensions (W x D x H) Digital Zoom Power supply Power consumption Operating temperature 1/0 connectors P7505Æ 155/PF-807/P7605/F 165/PF-WU07/P7305W/ F 125/PF-W07 series: 370 W user-replaceable lamp H9505BD/E255D/HE-822J series: 280 W user-replaceable lamp +/- 40 degrees Internal speaker with 3 W x 2 output 7.5 kg (16.5 lbs.) 398 mm x 310 mm x 140 mm (15.7″ x 12.2″ x 5.5″) AC input 100 – 240 V, 50 – 60 Hz P7505Æ 155/PF-807/P7605/F 165/PF-WU07/P7305W/ F 125/PF-W07 series: Normal mode: ± @ IIOVAC ECO mode: ± @ IIOVAC Standby mode < 0.5W H9505BD/E255D/HE-822J series: Normal mode: 337W ± @ IIOVAC ECO mode: ± @ IIOVAC Standby mode < 0.5W OOC to / to 1040F Power socket x 1 VGA input x2 Composite input xl S-Video xl VGA output xl HDMI x3 RS232 x 1: 9-pin male connector for projector remote control Mini USBx1: for firmware upgrade USB A x2 3.5 mm audio jack input x2 3.5 mm audio jack output xl SPDIF RCA jack output xl 3 RCA Component video xl 3.5 mm jack input x 1. for wired IR remote control RJ45 xl DC Jack xl ****** Page 59 ****** Standard package contents 49 AC power cord xl VGA cable xl Composite video cable xl Remote control xl Battery x 2 (for remote control) (option) User's Guide (CD-ROM) xl User's guide (CD-ROM) xl (for multi-media and wireless functions) Quick start guide xl Quick start guide xl (for multi-media and wireless functions) Security card xl Carrying case xl Dust filter xl Note: Design and specifications are subject to change without notice. ****** Page 60 ****** 50 Compatibility modes A. VGA Analog VGA Analog – PC Signal 1 Modes VGA SVGA XGA SXGA QuadVGA SXGA+ UXGA Power Mac G4 i Mac DV (G3) Resolution 640×480 640×480 640×480 640×480 640×480 800×600 800×600 800×600 800×600 800×600 800×600 1024×768 1024×768 1024×768 1024×768 1024×768 1 152×864 1 152×864 1152×864 1280×960 1280×960 1400×1050 1600×1200 640×480 640×480 800×600 1024×768 1 152×870 1280×960 1024×768 V.Frequency [Hz] 60 72 75 85 120 56 60 72 75 85 120 60 70 75 85 120 70 75 85 60 72 75 85 60 75 60 60 60 66.6(67) 60 60 75 75 75 H.Frequency [KHz] 31.5 37.9 37.5 43.3 61.9 35.1 37.9 48.1 53.7 77.4 48.4 56.5 60.0 68.7 99.0 63.8 67.5 77.1 64.0 77.0 80.0 91.1 60.0 752 65.3 75.0 31.4 34.9 37.9 48.4 68.7 75.0 60.0 ****** Page 61 ****** 2 3 1 VGA Analog – Extended Wide timing Modes WXGA WSXGA+ VGA Analog Modes 480i 576i 480p 576p 720p 720p 1080i 1080i 1080p 1080p 1080p Resolution 1280×768 1280×768 1280×768 1280×720 1280×720 1280×800 1440×900 1920×1200-RB 1680×1050 x (1080P) 1366×768 V.Frequency [Hz] 60 75 85 60 120 60 60 60 60 60 60 Component Signal Resolution 720×480(1440×480) 720×576(1440×576) 720×480 720×576 1280×720 1280×720 1920×1080 1920×1080 1920×1080 1920×1080 1920×1080 B. HDMI Digital HDMI PC Signal Modes VGA SVGA Resolution 640×480 640×480 640×480 640×480 640×480 800×600 V.Frequency [HzJ 59.94 (29.97) 50(25) 59.94 50 60 50 60(30) 50(25) 23.97/24 60 50 V.Frequency [Hz] 60 72 75 85 120 56 51 H.Frequency [KHz] 47.8 60.3 68.6 44.8 92.9 49.6 59.9 74.0 65.3 67.5 47.7 H.Frequency [KHz] 15.7 15.6 31.5 31.3 45.0 37.5 33.8 28.1 27.0 67.5 56.3 H.Frequency [KHz] 31.5 37.9 37.5 43.3 61.9 35.1 ****** Page 62 ****** 52 XGA SXGA QuadVGA SXGA+ UXGA Power Mac G4 i Mac DV (G3) 800×600 800×600 800×600 800×600 800×600 1024×768 1024×768 1024×768 1024×768 1024×768 1152×864 1152×864 1152×864 1280×1024 1280×1024 1280×1024 1280×1024 1280×960 1280×960 1400×1050 1600×1200 640×480 640×480 800×600 1024×768 1 152×870 1280×960 1024×768 2 HDMI Extended Wide timing Modes WXGA WSXGA+ Resolution 1280×768 1280×768 1280×720 1280×800 1440×900 1920×1200-RB 1680×1050 1920×1080-RB (1080P) 60 72 75 85 120 60 70 75 85 120 70 75 85 60 72 75 85 60 75 60 60 60 66.6(67) 60 60 75 75 75 V.Frequency [Hz] 60 75 85 60 120 60 60 60 60 60 37.9 48.1 46.9 53.7 77.4 48.4 56.5 60.0 68.7 99.0 63.8 67.5 77.1 64.0 77.0 80.0 91.1 60.0 75.2 65.3 75.0 31.4 34.9 37.9 48.4 68.7 75.0 60.0 H.Frequency [KHz] 47.8 60.3 68.6 44.8 92.9 49.6 59.9 74.0 65.3 67.5 ****** Page 63 ****** 1366×768 HDMI Video Signal 3 4 Modes 480i 576i 480p 576p 720p 720p 1080i 1080i 1080p 1080p 1080p Resolution 720×480( 1440×480) 720×576(1440×576) 720×480 720×576 1280×720 1920×1080 1920×1080 1920×1080 1920×1080 1920×1080 60 V.Frequency [Hz] 59.94 (29.97) 50(25) 59.94 50 60 50 60(30) 50(25) 23.97/24 60 50 53 47.7 H.Frequency [KHz] 15.7 15.6 31.5 31.3 45.0 37.5 33.8 28.1 27.0 67.5 56.3 HDMI – 1.4a 3D Timing Modes 720p (Frame Packing) 720p (Frame Packing) 1080p (Frame Packing ) 720p (Top and Bottom) 720p (Top and Bottom) 1080i (Top and Bottom) 1080i (Top and Bottom) 1080p (Top and Bottom) 1080p (Top and Bottom) 1080p (Top and Bottom) 720p (Side by Side (Half)) 1080i (Side by Side (Half)) 1080i (Side by Side (Half)) 1080p (Side by Side (Half) 1080p (Side by Side (Half) Graphic source monitor range limits Resolution 1280 x 720 1280 x 720 1920 x1080 1280 x 720 1280 x 720 1920 x1080 1920 x1080 1920 x1080 1920 x1080 1920 x1080 1280 x 720 1920 x1080 1920 x1080 1920 x1080 1920 x1080 V.Frequency [Hz] H.Frequency [KHzl 50 60 24 50 60 50 (25) 60 (30) 24 50 60 60 50 (25) 60 (30) 50 60 Horizontal scan rate: Vertical scan rate: Max. pixel rate: 37.5 45.0 27 .o 37.5 45.0 28.1 33.8 27.0 56.3 67.5 45.0 28.1 33.8 56.3 67.5 15k-lOOkHz 24-120 Hz na og: z Digital:165MHz ****** Page 64 ****** 54 Regulations and safety notices FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the device and receiver. Connect the device into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Notice: Peripheral devices Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this device. Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003. ****** Page 65 ****** 55 Remarque Ilintention des utilisateurs canadiens Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries Acer hereby declares that this projector series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Compliant with Russian regulatory certification UA TR 002 Radio device regulatory notice Note: The regulatory information below is for models with wireless LAN and/or Bluetooth only. General This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules). Canada — Low-power license-exempt radio communication devices (RSS-210) a b Common information Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Operation in 2.4 GHz band To prevent radio interference to the licensed service, this device is intended to be operated indoors and installation outdoors is subject to licensing List of applicable countries This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact the local office in the country of use. Please see ec.europa.eu/enterprise/rtte/implem.htm for the latest country list. ****** Page 66 ****** acer Acer Incorporated 8F. 88, Sec. 1. Xntai 5th Rd, Xizhi rqew Taipei City 221, Taiwan Declaration of Conformity Acer Incorporated 8F, 88, Sec. l, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan Contact Person: Mr. RU Jan, e-mail: email@example.com And, Acer Italy s.r.l Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 acer.lt Declare under our own responsibility that the product: Product: Trade Name: Model Number: DLP Projector Acer MIP1336/DWU1335/DIP1334/DWX1333 P7505/F155/PF-807/P7605/F165/PF-WU07/H9505BD/ E255D/HE-822J/P7305W/F125/PF-W07 To which this declaration refers conforms to the relevant standard or other standardizing documents: EN55022:2010 Class B; EN 55024:2010 ENG 1000-3-2:2006+A 1 Class A EN61000-3-3:2008 EN 60950-1 Regulation (EC) No. 1275/ 2008; EN 62301 :2005 EN50581:2012 We hereby declare above product is in compliance with the essential requirements and other relevant provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC and RoHS Directive 2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting ofecodesign requirements for energy-related product. Year to begin affixing CE marking 2013. RU Jan Sr. Manager Regulation, Acer Inc. Nov. 1 2013 Date ****** Page 67 ****** acer Acer America Corporation 333 West San Carlos St., Suite 1500 San Jose, CA 95110 Tel: 254-298-4011) Fax: 254-2984147 Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following local Manufacturer / Importer is responsible for this declaration: Product: Model Number: Machine Type: Name of Responsible Party: Addr'ess of Responsible Party: Contact Person: Phone No.: Fax No.: DLP Projector MIP1336/DWU1335/DIP1334/DWX1333 Pl 183/M403/PE-S42/X1183A/D603P/EV-S62T/ P7505/F155/PF-807/P7605/F165/PF-WU07/ 119505BD/E255D/HE-822.J/P7305W/F125/PF-W07 Acer America Corporation 333 West San Carlos St. Suite 1500 San Jose, CA 95110 Acer Representative 254-298-4000 254-298-4147
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL