Post questions, comments, reviews or page errors in the comment box below.

Click here to download ACER EV-X57H (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** Acer Projector Xl 126H/D506D/EV-S57H/V26S/AS600/ DSV1610 x 1226H/D516D/EV-X57H/V26X/AX600/ DNX1609 X 1326WH/D526D/EV-W57H/V26W/AW600/ DWX1608 User’s Guide

****** Page 2 ****** Copyright 0 2017. Acer Incorporated. All Rights Reserved. Acer Projector User’s Guide Original Issue: 01/2017 Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of th is manual or supplementary documents and publications. Th is company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particu lar purpose. Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your projector. All correspondence concerning your un it shou ld include the serial number, model number and purchase information. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electron ically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated. Model number: Serial number: Date of purchase: Place of purchase: Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies’ product names or trademarks are used herein for identification purposes only and belong to their respective companies. HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. I”

****** Page 3 ****** iii Information for your safety and comfort Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning Caution for plug as disconnecting device Observe the following guidelines when connecting and disconnecting power to the external power supply unit: Install the power supply unit before connecting the power cord to the AC power outlet. Unplug the power cord before removing the power supply unit from the projector. If the system has multiple sources of power, disconnect power from the system by unplugging all power cords from the power supplies. Caution for Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet. Warnings! Do not use this product near water. Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged. Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product. To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface.

****** Page 4 ****** Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, lamp. Using electrical power This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord. If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip’s input rating. This product’s AC adapter is equipped with a three-wire grounded plug The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the AC adapter plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details. Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury. Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product. Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length.

****** Page 5 ****** Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel when: the power cord or plug is damaged, cut or frayed liquid was spilled into the product the product was exposed to rain or water the product has been dropped or the case has been damaged the product exhibits a distinct change in performance, indicating a need for service the product does not operate normally after following the operating instructions Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Warning! For safety reasons, do not use non-compliant parts when adding or changing components. Consult your reseller for purchase options. Your device and its enhancements may contain small parts. Keep them out of the reach of small children. Additional safety information Do not look into the projector’s lens when the lamp is on. The bright may hurt your eyes. Turn on the projector first and then signal sources Do not place the product in following environments: Space that is poorly ventilated or confined. At least 50cm clearance from walls and free flow of air around the projector is necessary. Locations where temperatures may become excessively high, such as inside of a car with all windows rolled up Locations where excessive hum idity, dust, or cigarette smoke may contam inate optical components, shortening the life span and darken ing the image. Locations near fire alarms. Locations with an ambient temperature above 40 oc/104 OF. Locations where the altitudes are higher than 10000 feet. Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector. It might cause fire or electric shock. In this case, unplug immediately and

****** Page 6 ****** VI contact your dealer. Do not keep using this product to break or drop it. In this case contact your dealer for inspection. Do not face the projector lens to the sun. It can lead to fire. When switching the projector off, suggest to ensure the projector completes its cooling cycle before disconnecting power. Do not frequently turn off the main power abruptly or unplug the projector during operation. The best way is to wait for the fan to turn off before turning main power off. Do not touch air outlet grille and bottom plate which becomes hot. Clean the air filter frequently if have. The temperature inside may rise and cause damage when the filter/ventilation slots clogged with dirt or dust. Do not look into the air outlet grille when projector is operating. It may hurt your eyes. Always open the lens shutter or remove the lens cap when the projector is on. Do not block the projector lens with any object when the projector is under operation as this could cause the object to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press HIDE on the remote control. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. It could cause it to break on rare occasions. Never replace the lamp assembly or any electronic components unless the projector is unplugged. The product will detect the life of the lamp itself. Please be sure to change the lamp when is showing warning message. When changing the lamp, please allow unit to cool down, and follow all changing instructions. Reset the “Lamp Hour Reset” function from the Onscreen display ” Management” menu after replacing the lamp module. Do not attempt to disassemble this projector. There are dangerous high voltages inside which may hurt you. The only user serviceable part is the lamp which has its own removable cover. Refer servicing only to suitable qualified professional service personnel Do not stand the projector on end vertically. It may cause the projector to fall over, causing injury or damage. This product is capable of displaying inverted images for ceiling mount installation. Only use acer ceiling mount kit for mounting the projector and ensure it is securely installed

****** Page 7 ****** vii Caution for Listening To protect your hearing, follow these instructions. Increase the volume gradually until you can hear clearly and comfortably. Do not increase the volume level after your ears have adjusted Do not listen to music at high volumes for extended periods. Do not increase the volume to block out noisy surroundings. Decrease the volume if you can ‘t hear people speaking near you. Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit acer-group.com/public/Sustainability/$ustainability01.htm Mercury advisory For projectors or electronic products containing an LCD/CRT monitor or display: ‘Lamp(s) contain Mercury, Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the Electronic Industries Alliance at eiae.org. For lamp-specific disposal information, check lamprecycle.org RISK GROUP 2 CAUTION Possibly hazardous optical radiation emitted from this product Groupe de risque 2 ATTENTION Rayonnement optique evéntuellement dangereux émis par ce produit Do not stare into the beam, RG2 ” As with any bright source, do not stare into the direct beam, RG2 IEC 62471- 5:2015″

****** Page 8 ****** VIII First things first Usage Notes Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don’t: Block the slots and openings on the unit provided for ventilation. Use abrasive cleaners, waxes or solvents to clean the unit. Use under the following conditions: In extremely hot, cold or humid environments. In areas susceptible to excessive dust and dirt. Near any appliance that generates a strong magnetic field. Place In direct sunlight. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s guide to maximize the life of your unit. Warning: Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes. To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Please do not open or disassemble the product as this may cause electric shock. When changing the lamp, please allow unit to cool down, and follow all changing instructions. This product will detect the life of the lamp itself. Please be sure to change the lamp when it shows warn ing messages. Reset the “Lamp Hour Reset” function from the Onscreen display ” Management” menu after replacing the lamp module. When switching the projector off, please ensure the projector completes its cooling cycle before disconnecting power. Turn on the projector first and then the signal sources. Do not use lens cap when projector is in operation. When the lamp reaches the end of its life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp ‘I .

****** Page 9 ****** Information for your safety and comfort First things first Usage Notes Precautions Introduction Product Features Package Overview Projector Overview Projector Outlook Control Panel Remote Control Layout MHL (Mobile High-Definition Link) Control Getting Started Connecting the Projector Turning the Projector On/Off Turning on the Projector Turning the projector off Adjusting the Projected Image Adjusting the Height of Projected Image How to optimize image size and distance How to get a preferred image size by adjusting distance and zoom User Controls Installation menu Onscreen Display (OSD) Menus Color lma ge Setting Management Audio 3D Language Appendices iii viii VIII VIII 1 2 3 3 5 6 8 10 10 11 11 12 13 13 14 16 18 18 19 20 22 24 27 28 28 29 30

****** Page 10 ****** Troubleshooting LED & Alarm Definition Listing Cleaning and replacing the dust filters (Option) Replacing the Lamp Ceiling Mount Installation Specifications Compatibility modes Regulations and safety notices 30 34 35 36 38 41 43 48

****** Page 11 ****** 1 Introduction Product Features This product is a single-chip DLP@ projector. Outstanding features include: DLP@ technology Xl 126H/D506D/EV-S57HN26S/AS600/DSV1610 series: 800×600 SVGA resolution X 1226H/D516D/EV-X57HN26X/AX600/DNX 1609 series: 1024×768 XGA resolution X1326WH/D526D/EV-W57HN26W/AW600/DWX1608 series: 1280×800 WXGA resolution Full/4:3/16:9/L.Box aspect ratio supported Enables projecting 3D content via DLP Link Technology: Blue-Ray 3D supported Acer ColorBoost technology delivers nature’s true colors for vivid, life-like images High brightness and contrast ratio Aer LumiSense technology can intelligently optimize the projection images to the most comfortable visual lumens automatically based on display content. Versatile display modes (Bright, Presentation, Standard, Video, Game, Education, User) enable optimum performance in any situation NTSC / PAL / SECAM compatible and HDTV (480i/p, 576i/p, 720p, 1080i/p) supported Lower power consumption and economy (ECO) mode extend lamp life Acer EcoProjeciton Technology delivers Intelligent power management approach and physical efficiency improvement Equipped with HDMITM & MHL connection supporting HDCP Smart detection delivers quick, intelligent source detection Multi-language onscreen display (OSD) menus Manual focus projection lens zooms up to 1. lx 2x digital zoom Microsoft@ Windows@ 2000, XP, Vista@, Windows 7, Windows 8.1, Windows 10, Macintosh@ OS compliant Support MHL V2.1 signal display Support LumiSense Built-in One 3 Watts speaker Note: Functions vary depending on model definition.

****** Page 12 ****** 2 Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if any thing is missing Projector Acer Projector Security Card Security card (option) Carrying case (option) AAA battery x2 (option) Power cord User’s guide (option) Dust filters (option) WirelessCAST (option) VGA cable Projector Quick start guide Remote control WirelessHD-Kit (option)

****** Page 13 ****** Projector Overview Projector Outlook Front / upper side 2 8 3 9 4 7 8 9 10 11 5 11 6 3 7 10 escriptlon 1 2 3 4 5 6 1 escriptlon Air outlet Focus ring Zoom ring Remote control receiver Power button Control panel Lamp cover Lens cap Projection lens Tilt adjusting wheels Air inlet

****** Page 14 ****** 4 Right / Rear side 12345 6 7 6 2 3 4 5 6 7 escnptlon Power socket HDMI I/MHL connector KensingtonTM lock port HDMI 2 connector 5V DC output connector (device charge & support mouse page up/down function) PC analog signal/HDTV/component video input connector (VGA IN 1, VGA RS232 connector 8 9 10 11 12 13 89 11 1213 10 ‘*’OEO AUC*O’N escriptlon Monitor loop-through output connector (for VGA IN 1 on ly) S-Video input connector Composite video input connector Audio in 2 connector (for S-Video, Composite) Audio in 1 connector (for VGA IN 1, VGA IN 2) Audio out connector Note: Functions vary depending on model definition.

****** Page 15 ****** Control Panel 4 5- 6 POWER BACK 2 LAMP ENTER ‘ 3 TEMP SOURCE MENU 1 5 7 8 9 10 escnptlon 1 2 3 4 5 6 7 8 9 10 con POWER LAMP TEMP A BACK SOURCE ENTER MENU unction POWER LAMP TEMP POWER Four directional select keys BACK SOURCE ENTER Keystone MENU Power Indicator LED Lamp Indicator LED Temp Indicator LED See the contents in “Turning the Projector On/Off” section. Use to select items or make adjustments to your selection. Returns to the previous operation. Changes the active source. Confirm your selection of items. Adjusts the image to compensate for distortion caused by tilting the projector. Press i’ MENU” to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu. Note: Functions vary depending on model definition.

****** Page 16 ****** 6 Remote Control Layout 2 3 4 5 6 11 12 13 14 1 16 17 18 1 7 8 9 10 19 20 21 22 23 24 25 e EMER 26 o 27 41 MENU 1 4 7 2 3 5 ooc FC 2 3 4 5 6 7 8 9 10 11 12 con d) MUTE RATIO ENTER MODE VGA 2 un Ion Infrared tran sm itter POWER MUTE RATIO Select/Enter Playmause Four directional select keys SOURCE MODE KEYSTONE BACK STOP VGA escrip Ion Sends signals to the projector. Refer to the “Turning the Projector On/Off” To turn on/off the volume. To choose the desired aspect ratio. Confirm your selection of items. Press to begin/pause playback. section. Use up, down, left, right buttons to select items or make adjustments to your selection. Press “3D ” to select 3D models. Changes the active source. Press “MODE” to select the display mode from Bright, Presentation, Standard, Video and User. Adjusts the image to compensate for distortion caused by tilting the projector. Returns to the previous operation. Press to stop playback. Press “VGA” to change source to the VGA connector. Th is connector supports analog RGB, YPbPr (480p/576p/720p/ 1080i), YCbCr (480i/576i) and RGBsync.

****** Page 17 ****** 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Icon FREEZE 1 pgup COMPONENT 5 71 MEDIA 8 MENU HOUWMHL 3 ZOOM IN VIDEO 6 ZOOM LANWFi 9 Function FREEZE PgUp COMPONENT PgDn MEDIA KeyPad 0-9 MENU HDMITM/MHL HIDE ZOOM IN VIDEO ZOOM OUT LANWiFi Laser pointer Laser button 7 Description To pause the screen image. For computer mode only. Use this button to select the previous page. This function is on ly available when USB Ctrl connector (mini type B) is connected to a computer via a USB cable. No function. For computer mode only. Use this button to select the next page. This function is only available when USB Ctrl connector (m ini type B) is connected to a computer via a USB cable. No function. Press “0-9” to input a password in the “Security” OSD. Press ” MENU” to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu. Confirm your selection of items. To change source to HDMI/MHL. Momentarily turns off the video. Press “HIDE” to hide the image, press again to display the image. Zooms the projector display in. To change source to COMPOSITE VIDEO. Zooms the projector display out. Press “LANNViFl” to change source to “WiFi.” Only available while Acer WirelessCAST (MWA3) is plgged in projector and see “WiFi” in source list. Aim the remote at the viewing screen. Aim the remote at the viewing screen, press and hold this button to activate the laser pointer. Note: Functions vary depending on model definition.

****** Page 18 ****** 8 MHL (Mobile High-Definition Link) Control MHL Control Mode Navigation RATIO ENTER 2 3 4 6 7 MHL Control Mode Numeric 8 9 11 2 3 4 5 6 7 8 9 MENU FREEZE VGA HIDE toco Pgup ooo 4 oco 7 Next Wide MHL Control Mode Multi-Media Next Mods Description con SURCE MODE MUTE MENU SACK. Function SOURCE MODE MUTE Volume UP Volume Down Select/Enter Play/Pause MENU Four directional select keys Back/Exit Stop Press the “SOURCE” button to toggle between Navigation, Numeric and Mu Iti-Media mode. Press “MODE” button for one second to activate the MHL Control Mode. To exit, press the “MODE” button again. To turn on/off the volume. (only for Navigation or Multi- Media mode) Increases the volume. (on ly for Multi-Media mode) Decreases the volume. (on ly for Multi-Media mode) Press to select/enter the file. (only for Navigation mode) Toggles between playback and pause. (only for Multi- Media mode) Press to launch the root memu. (on ly for Navigation mode) Use up, down, left, right buttons to select items or make adjustments to your selection. (on ly for Navigation mode) Press “BACK” to go back one menu step. To exit the file. (on ly for Navigation mode) Discontinues playback. (on ly for Multi-Media mode)

****** Page 19 ****** Icon Pgup PgDn 10 11 Function PgUp/PgDn KeyPad 9 Description Use the button to select the next or previous page. (only for Navigation mode) Number buttons. (on ly for Numeric mode) Note: Functions vary depending on model definition.

****** Page 20 ****** 10 Getting Started Connecting the Projector DVD player, Set-top Box, HDTV receiever DVD player 4 5 7 6 3 2 1 Smart Phone HDMi 4 Power Bank 3 RS232 Description 12 o-sub 7 8 II 9 10 Audio output •OOO 9 Video output 2 3 4 5 6 Power cord MHL cable (MicroUSB to HDMI) HDMI cable USB cable for charging device 3 RCA component cable VGA to component/HDTV adapter 11 7 8 9 10 11 12 S-Video output Description VGA cable Audio cable Jack/Jack Audio cable JackRCA Composite video cable S-Video cable RS232 cable Note 1: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector. Note 2: Functions vary depending on model definition. Note 3: USB cable needs powered extender if the length is over 5 m. Note 4: Some smartphones require a converter (supplied by smartphone maker) to enable the MHL function. Note 5: USB DC 5V out connector support 5V/2.OA power output for power bank charging only when MHL source is not detected. Note 6: VGA OUT loops through for VGA IN 1 only.

****** Page 21 ****** 11 Turning the Projector On/Off Turning on the Projector 1 2 3 Ensure that the power cord and signal cable are securely connected. The Power indicator LED will flash red. Turn on the projector by pressing “Power” button on the control panel or remote control, and the Power indicator LED will turn blue. Turn on your source (computer, notebook, video player ,etc.). The projector will detect your source automatically. If the screen displays i’ Lock” and “Source” icons, it means the projector is locked onto a specific source type and there is no such type of input signal detected If the screen displays i’ No Signal”, please make sure the signal cables are securely connected or press source direct key. If you connect to multiple sources at the same time, use the “Source” button on either control panel or the remote control or direct source key on the remote control to switch between inputs. Power button

****** Page 22 ****** 12 Turning the projector off 1 2 3 4 5 To turn the projector off, press and hold the power button. This message appears: “Please press the power button again to complete the shutdown process.” Press the power button again. The LED power indicator will turn RED and blink rapidly after the projector is turned off, and the fan(s) will continue to operate for about 2 minutes to ensure that the system cools properly. (only supported under “lnstant Resume” mode) As long as the power cord remains plugged in, you can press the power button to turn the projector immediately back on anytime during the 2- minute shutdown process. (only supported under “lnstant Resume” mode) Once the system has finished cooling, the LED power indicator will stop blinking and turn solid red to indicate standby mode. It is now safe to unplug the power cord. Warning indicators: “Projector Overheated. Lamp will automatically turn off soon.” This onscreen message indicates that the projector has overheated. The lamp with automatically turn off, the projector will automatically shut down, and the LED temp indicator will turn solid red. Contact your local dealer or service center. “Fan failed. Lamp will automatically turn off soon.” This onscreen message indicates that the fan has failed. The lamp will automatically turn off, the projector will automatically shut down, and the LED temp indicator will blink. Contact your local dealer or service center. Note 1: Whenever the projector automatically shuts down and the LED lamp indicator turns solid red, contact your local reseller or service center. Note 2: Functions vary depending on model definition. Attention! The projector will enter a two minute cool down period to ensure continued optimal lamp operation. Attention! Please do not turn off projector within 1 minute after power on.

****** Page 23 ****** 13 Adjusting the Projected Image Adjusting the Height of Projected Image The projector is equipped with elevator feet for adjusting the height of image. To raise/lower the image: Use Tilt adjusting wheel to fine-tune the display angle. Tilt adjusting wheel

****** Page 24 ****** 14 How to optimize image size and distance Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen. SVGA/XGA series If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 46″ and 51 ” Note: Remind as below figure, the space of 89 cm height is required when located at 2 m distance. a *screen size 2.0 m Desired Dista nce Height 80 cm c Screen size Height: 89 c from base to op of image Top Desired Distance Screen size (Min zoom) Top (Max zoom) From ase to (m) Diagonal Diagonal From base to top W (cm)x H top of image (inch) 1.0 22.78 1.5 34 2.0 46 3.0 68 4.0 91 5.0 114 6.0 137 7.0 159 8.0 182 9.0 205 10.0 228 11.0 251 11.8 269 Zoom Ratio: 1 lx (cm) 46 x 35 69 x 52 93 x 69 139 x 104 185 x 139 231 x 174 278 x 208 324 x 243 370 x 278 417 x 313 463 x 347 509 x 382 546 x 410 (cm) 40 60 80 120 160 200 240 280 319 359 399 439 471 (inch) 25 38 51 76 101 127 152 178 203 228 254 279 299.3 W (cm) x (cm) 52 x 39 77 x 58 103 x 77 155 x 116 206 x 155 258k 193 309 x 232 361 x 271 412 x 309 464 x 348 515 x 387 567 x 425 608 x 456 of image (cm) 67 89 133 178 222 267 311 356 400 445 489 525

****** Page 25 ****** 15 WXGA series If the projector is 2 m from the screen, good image quality is possible for image sizes between 54″ and 60″ Note: Remind as below figure, the space of 91 cm height is required when located at 2 m distance. ax screen size Screen size Desired Dista nce Top 540 Heig Screen size Height: 91 m from base otop t- Of image Top Desired Distance (Min zoom) From ase to (Max zoom) (m) Diagonal Diagonal From base to top W (cm)x H top of image (inch) 26.99 1.5 40 2.0 54 2.5 67 3.0 81 3.5 94 4.0 108 4.5 121 5.0 135 6.0 162 7.0 189 8.0 216 9.0 243 10.0 270 Zoom Ratio: 1 lx (cm) 58 x 36 87 x 55 116 x 73 145 x 91 174 x 109 203 x 127 233 x 145 262 x 164 291 x 182 349 x 218 407 x 254 465 x 291 523 x 327 581 x 363 (cm) 41 61 81 102 122 142 163 183 203 244 285 326 366 407 (inch) 30 45 60 75 90 106 121 136 151 181 211 241 271 301.47 W (cm) x (cm) 65 x 41 97 x 61 130×81 162K 101 195 x 122 227 x 142 260K 162 292K 183 325 x 203 390 x 244 455 x 284 519 x 325 584 x 365 649 x 406 of image (cm) 45 68 91 114 136 159 182 205 227 273 318 364 409 455

****** Page 26 ****** 16 How to get a preferred image size by adjusting distance and zoom The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring SVGA/XGA series To obtain an image size of 60″ set the projector at a distance 2.4 m and 2.6 m from the screen. 2.6 m c Desired Image Size Desired image size 4.4 m B Desired Distance Distance (m) Diagonal (inch) Max zoom Min zoom 30 40 50 60 70 80 90 100 150 180 200 250 300 Zoom Ratio: 1. lx W (cm) x H (cm) 61×46 81 x 61 102 x 76 122 x 91 142 x 107 163 x 122 183 x 137 203 x 152 305 x 229 366 x 274 406 x 305 508 x 381 610 x 457 1.2 1.6 2.0 2.37 2.8 3.2 3.5 3.9 5.9 7.1 7.9 9.9 11.8 1.3 1.8 2.2 2.6 3.1 3.5 4.0 4.4 6.6 7.9 8.8 11.0 Height: 105 c from base to top ,of image Top (cm) From base to top of mage 53 70 88 105 123 140 158 175 263 315 351 438 526

****** Page 27 ****** 17 WXGA series To obtain an image size of 60″ set the projector at a distance 2.0 m and 2.2 m from the screen. 2.2 m c Desired Image Size Desired mage Size 010 m – Desired Distance Distance (m) Diagonal (inch) 30 40 50 60 70 80 90 100 120 150 180 200 250 300 Zoom Ratio: 1. lx W (cm) x H (cm) 65 x 40 86 x 54 108 x 67 129 x 81 151 x 94 172x 108 194x 121 215 x 135 258x 162 323 x 202 388 x 242 431 x 269 538 x 337 646 x 404 Max zoom 1.0 1.3 1.7 2.0 2.3 2.7 3.0 3.3 4.0 5.0 6.0 6.6 8.3 10.0 Min zoom 1.5 1.9 2.2 2.6 3.0 3.3 3.7 4.4 5.6 6.7 7.4 9.3 11.1 Height: 9 cm from base t top of mage Top (cm) rom ase to top o mage 45 60 75 90 106 121 136 151 181 226 271 302 377 452

****** Page 28 ****** 18 User Controls Installation menu The installation menu provides an onscreen display (OSD) for projector installation and maintenance. Use the OSD only when the message “No signal input” is displayed on the screen. The menu options include settings and adjustments for screen size and distance, focus, keystone correction and more 1 2 3 4 5 Turn on the projector by pressing ” Power” button on the control pad. Press the ” MENU” button on the remote control to launch the OSD for projector installation and maintenance. nr LM.w u• u The background pattern acts as a guide to adjusting the calibration and alignment settings, such as screen size and distance, focus and more . The Installation menu includes the following options: •Projection Mode •Projection Location •Auto Keystone settings •Manual Keystone settings •WirelessHD Dongle Pairing •Language settings •Reset to factory default function Use the up and down arrow keys to select an option, the left and right arrow keys to adjust selected option settings, and the i’ ENTER” to enter a submenu for feature setting. The new settings will be saved automatically upon exiting the menu. Push the “MENU” or “BACK” button anytime to exit the menu and return to the Acer welcome screen. Note: Functions vary depending on model definition.

****** Page 29 ****** 19 Onscreen Display (OSD) Menus The projector has multilingual OSD that allow you to make image adjustments and change a variety of settings. Using the OSD menus To open the OSD menu, press “MENU” on the remote control or control panel. When the OSD is displayed, use the A v keys to select any item in the main menu. After selecting the desired main menu item, press “ENTER” to enter submenu for feature setting Use the A v keys to select the desired item and adjust the settings by using the < keys. Select the next item to be adjusted in the submenu and adjust as described above. Press " BACK" on the remote control or control panel, the screen will return to the main menu. To exit OSD, press "BACK" on the remote control or control panel. The OSD menu will close and the projector will automatically save the new settings. Main menu Color LumiSense BluelightShield Display Mode VVall Color Brightness Contrast Color Temperature Gamma Exit Sub menu 50 Select Off Off Presentation Enter Enter Setting ABC Note 1: Some of the following OSD settings may not be available. Please refer to the actual OSD of your projector. Note 2: Functions vary depending on model definition. ****** Page 30 ****** 20 Color LumlSense BluelightShield Display Mode Wall color Brightness Contrast Saturation Acer Lum iSense technology can intelligently optimize the projection images to the most comfortable visual lumens automatically based on display content. The feature greatly enhances dark detail visibility and color saturation. Off: Default setting. Normal: Select "Normal" to meet the visual effect of dark detail enhancement. Boost: Select "Boost" to meet the visual effect of brightness boost. Dynamic Black:automatically optimize the display of dark movie scenes enabling them to be shown in incredible detail. : Once LumiSense is enabled, BluelightShield switches to “Off”. Off: Default setting. Low / Medium / High: Select Low / Medium / High to reduce different exposure levels of blue light dynamically. : Once BluelightShield is enabled, LumiSense switches to “Off”. There are many factory presets optimized for various types of mages. Bright: For brightness optimization. Presentation: For meeting presentation. Standard: For common environment. Video: For playing video in a bright environment. Game: For game content. Education: For education environment. User: Memorize user’s settings. Use this function to choose a proper color according to the wall. There are several choices, including wh ite, light yellow, light blue, pink, dark green. It will compensate the color deviation due to the wall color to show the correct image tone. Adjust the brightness of the image. Press to darken the image. Press to lighten the image. “Contrast” controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press < to decrease the contrast. Press to increase the contrast. Adjusts a video image from black and white to fu Ily saturated color. Press < to decrease the amount of color in the image. Press to increase the amount of color in the image. ****** Page 31 ****** Tint Color Temperature Gamma 21 Adjusts the color balance of red and green Press to increase the amount of green in the image. Press to increase the amount of red in the image. Mode Use this function to choose CT 1, CT 2, CT 3, User mode. R Gain Adjusts the red gain for color temperature optim ization. G Gain Adjusts the green gain for color temperature optimization. B Gain Adjusts the blue gain for color temperature optim ization. Effects the representation of dark scenery. With greater gamma value, dark scenery looks brighter. • "Saturation " and "Tint" functions are not supported under Note 1. computer or HDMI mode. Note 2: Functions vary depending on model definition. ****** Page 32 ****** 22 Image Projection Mode Projection Location Aspect Ratio Auto Keystone Manual Keystone Sharpness H. Position (Horizontal position) V. Position (Vertical position) Frequency Tracking Front: The factory default setting. Rear: Reverses the image so you can project from behind a translucent screen. Auto: Automatically adjusts projection location of image. Desktop Ceiling: Turns the image upside down for ceiling-mounted projection. Use th is function to choose your desired aspect ratio. Auto: Keep the image with original width-higth ratio and maxi mize the image to fit native horizontal or vertical pixels. Full: Resize image to fit full screen by width (1280 pixels) and height (800 pixels) 4:3: The image will be scaled to fit the screen and displayed using a 4:3 ratio. 16:9: The image will be scaled to fit the width of the screen and the height adjusted to display the image using a 16:9 ratio. L.Box: Keep original signal aspect ratio and zoom in by 1.333 times. Automatically adjusts vertical image. Adjust image distortion caused by tilting projection. The Manual Keystone function is unavailable under Auto Keystone setting to “On ‘I . Adjusts the sharpness of the image. Press Press Press Press Press Press to decrease the sharpness. to increase the sharpness. to move the image left. to move the image right. to move the image down. to move the image up. “Frequency” changes the projector’s refresh rate to match the frequency of your computer’s graphics card. If you can see a vertical flickering bar in the projected image, use this function to make the necessary adjustments. Synchron izes the signal timing of the projector with the graph ics card If you experience an unstable or flickering image, use th is function to correct it.

****** Page 33 ****** 23 HDMI Color Range Adjust the color range of the HDMI image data to correct color display error. Auto: Automatically adjust by information from player. Limited Range: Prosess the input image as limited color range data. Full Range: Prosess the input image as full color range data. HDMI Scan Info Adjust the overscan ratio of the HDMI image on screen. Auto: Automatically adjust by information from player. Underscan: Always no overscan on HDMI image. Overscan: Always keep overscan on HDMI image. H. Position ‘I, “V. Position”, “Frequency” and “Tracking” functions Note 1: ” are not supported under HDMI or Video mode. Note 2: “HDMI Color Range” and “HDMI Scan Info” functions are only supported under HDMI mode. Note 3: Functions vary depending on model definition.

****** Page 34 ****** 24 Setting Source Selection Closed Caption VGA OUT (Standby) Manual by source menu, Auto by Smart Detection. Selects a preferred closed captioning mode from CCI, CC2, CC3, CC4, (CCI displays captions in the primary language in your area). Select “Off” to turn off the captioning feature. This function is on ly available when a composite video or S-Video input signal is selected and its system format is NTSC. Set your screen aspect ratio to 4:3. This function is not available when the aspect ratio is ” 16:9″ or “Auto” . Default is “Off” . Choose “On ” to enable VGA OUT connection.

****** Page 35 ****** Security Reset 25 Security Th is projector provides a useful security function for the admin istrator to manage usage of the projector . Press “ENTER ” to change the “Security” setting. If the security function is enabled, your must enter the “Admin istrator Password” first before changing the security settings. Select “On ” to enable the security function. The user has to enter a password to operate the projector. Please refer to the ‘User Password” section for details. If “Off” is selected, then the user can turn on the projector without password. Timeout(Min.) Once “Security” is activated to ” On”, the administrator can set timeout function. Press or to select the timeout interval. The range is from 10 minute to 990 minutes. When the time is up, the projector will prompt the user to enter the password again. The factory default setting of “Timeout(Min.)” is “Off” . Once the security function is enabled, the projector will request user to enter password when switch on the projector . Both “User Password” and “Administrator Password” can be accepted for this dialogue. User Password Press “ENTER ” to setup or change the “User Password” Press number keys to set your password on the remote control and press ” ENTER” to confirm. Press < to delete character. Enter the password when you see "Confirm Password " displayed. The password should be between 4 and 8 characters long. If you select "Request password only when plugging the power cord in.", the projector will prompt the user to enter the password every time the power cord is plugged. If you select "Always request password while projector turns on. " , the user has to enter the password every time when the projector is turned on. Administrator Password The "Administrator Password" can be used in both the "Enter Admin istrator Password" and "Enter Password" dialog boxes. Press "ENTER " to change the "Administrator Password" . The factory default of "Administrator Password" is "1234" . If you forgot your adm inistrator password, do the following to retrieve the administrator password: An unique 6-digit " Universal Password" which is printed on the Security Card (please check accessory in the box). Th is un ique password is the number which will be accepted by projector anytime no matter what the Adm inistrator Password is. If losing this security card and number, please contact with an Acer service center. Press the " ENTER " button and choose "Yes" to return the parameters on all menus to the factory default settings. ****** Page 36 ****** 26 Information Display the projector information for Model Name, Input Source, Signal Type, Display Mode, Serial No. , Software Version and QR code on the screen. Scan QR code linking to Acer projector portal via mobile. Note: Functions vary depending on model definition. ****** Page 37 ****** 27 Management ECO Mode High Altitude Turn Off Mode Auto Shutdown Menu Display Time (Seconds) AC Power On Control Panel Lock Lamp Hour Elapse Lamp Reminding Lamp Hour Reset Choose "On" to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose "Off" to return normal mode. Gray out ECO mode item while either Lumisense or BluelightShield item is “On . Choose “On ” to turn on High Altitude mode. Operate the fans at fu II speed continuously to allow for proper high altitude cooling of the projector. Standard: Properly shuts down the projector after fan cooling. Instant Resume: Resumes the system when the Power button is pressed again within 2 minutes. The projector will automatically shutdown when there is no signal input after the allocated time. (default is 15 minutes) Choose the OSD menu display time. (Default is 15 seconds). Select “Manual” to turn off main menu/one direct-key menu manually by user. Choose “On” to power on projector while AC power plug in. Off Default is set to “Off”. Child Lock Enable “Child Lock” to disable the power key on projector wh ile in the standby mode to avoid power trigger from children. (Take effect after power off). Disable “Child Lock” temporarily to turn on projector by quick key, holding the power key on projector for 3 seconds. No need to lock any key after power on. Full Lock Enable “Full Lock” to lock all keys on projector. (Take effect once done the setting; show warning message wh ile user presses keypad.) Disable “Full Lock” function, press “ENTER” key for 7 seconds. And then, the OSD of “Control Panel Lock” is set to “Off” and not required to go back to “Full Lock” again. Pop up a warning message: To disable “Full Lock” function, press “ENTER” key for 7 second, wh ile user presses any key on keypad panel under “Full Lock” mode. Displays the lamp’s elapsed operating time (in hours). Activate th is function to display a reminder to change the lamp 30 hours before its expected end-of-life. Press the ” ENTER ” button and choose “Yes” to turn the lamp hour counter to 0 hours. Note: Functions vary depending on model definition.

****** Page 38 ****** 28 Audio Volume Mute 3D Format 24P 3D 3D LR Invert Press to decrease the volume. Press to increase the volume. Choose “On ” to mute the volume. Choose “Off” to restore the volume. Note: Functions vary depending on model definition. 3D Warning Message Choose “On ” to enable DLP 3D function. • On: Choose this item while using DLP 3D glasses, 120Hz 3D capable graphics cards and HQFS format file or DVD with corresponding SW player. • Off: Turn oft 3D mode. If the 3D content is not displayed correctly, you can select a 3D format that suits the 3D content you are viewing and obtain the best result. Choose “96Hz” or ” 144Hz” to compatible with 3D glasses. If you see a discrete or overlapping image while wearing DLP 3D glasses, you may need to execute ” Invert” to get best match of left/right image sequence to get the correct image (for DLP 3D). Choose “On ” to display the 3D warning message. Note; 3D display is enabled. 1. Please make sure you have the correct 30 signals and glasses. 2. Remember to turn 3D off if you dont want to see 30 images. 3, Ifthe 30 display isnt correct, please try to enable 30 Sync Invert. 4, Oisplay mode options will be disabled Mlile in 30 mode. Note 1: It needs correct settings on graph ic card 3D application program for correct 3D display. Note 2: The SW players, such as Stereoscopic Player and DDD TriDef Media Player can support 3D format files. You can download these three players on web page below, – Stereoscopic Player (Trial) http ://3dtv.at/Down loads/ln dex_en .aspx – DDD TriDef Media Player (Trial): tridef.com/down load/TriDef-3-D-Experience-4.0.2.html Note 3: “3D L/R Invert” is only available when 3D is enabled. Note 4: There has rem inder screen if 3D still enable when power on projector. Please adjust setting depended on your purpose. Note 5: WUXGA model 24P 3D cannot be scaling due to Tl ASIC buffer

****** Page 39 ****** 29 memory limitation, and once detect 24P 3D (96Hz or 144Hz) inputs, Aspect Ratio / HDMI Scan Info will be gray out, also HIDE will be not supported. Language Language Choose the multilingual OSD menu. Use the A key to select your preferred menu language. Press “ENTER” to confirm the selection.

****** Page 40 ****** 30 Appendices Troubleshooting If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center. Image Problems and Solutions 2 Problem No image appears onscreen Partial, scrolling or incorrectly displayed image (for PC (Windows 2000/XPNista/ Windows 7/ Windows 8)) Solution Connected as described in the “Getting Started” section. Ensure none of the connector pins are bent or broken. Check if the projector lamp has been securely installed. Please refer to the “Replacing the Lamp ” section. Make sure you have removed the lens cap and the projector is switched on. For an incorrectly displayed image: Open “My Computer”, open the “Control Panel”, and then double-click the “Display” Icon. Select the “Settings” tab Verify that your display resolution setting is lower than or equal to WUXGA-RB (1920 x 1200). Click the “Advanced Properties” button. If the problem still appears, change the monitor display you are using and follow the steps below Verify that the resolution setting is lower than or equal to WUXGA-RB (1920 x 1200). Click the “Change” button under the ” Mon itor” tab. Click “Show all devices”. Next, select “Standard mon itor types” under the SP box, and choose the resolution mode you need under the ” Models” box. Verify that the resolution setting of the mon itor display is lower than or equal to WUXGA-RB (1920 x 1200).

****** Page 41 ****** 3 4 5 6 7 8 Partial, scrolling or incorrectly displayed image (For notebooks) The screen of the notebook computer is not displaying your presentation Image is unstable or flickering Image has vertical flickering bar Image is out of focus Image is stretched when displaying a ” widescreen DVD title 31 For an incorrectly displayed image: Follow the steps for item 2 (above) to adjust the resolution of your computer. Press the toggle output settings. Example: [Fn]+[F4], Compaq Dell Gateway IBM HP NEC Tosh iba If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector. If you are using a Microsofte Windows@ based notebook: Some notebook PCs may deactivate their own screens when a second display device is in use. Each has a different way to be reactivated. Refer to your computer’s manual for detailed information If you are using an Apple Mac@ OS based notebook: In System Preferences, open Display and select Video Mirroring “On” Adjust the “Tracking” to correct it. Refer to the ” Image” section for more information. Change the display color depth settings on your computer. Use “Frequency” to make an adjustment. Refer to the ” Image” section for more information. Check and reconfigure the disp lay mode of your graphics card to make it compatible with the projector. Make sure the lens cap is removed. Adjusts the focus ring on the projector lens. Make sure the projection screen is within the required distance of 3.3 to 38.7 feet (1.0 to 11.8 meters) (SVGA/XGA series) / 3.3 to 32.8 feet (1.0 to 10.0 meters) (WXGA series) from the projector. Refer to the “How to get a preferred image size by adjusting distance and zoom ” section for more information. When you play a DVD encoded in anamorphic or 16:9 aspect ratio you may need to adjust the following settings: If you play a 4:3 format DVD title, please change the format to 4:3 in the projector OSD. If the image is still stretched, you will also need to adjust the aspect ratio. Set up the display format to 16:9 (wide) aspect ratio on your DVD player. If you play an Letterbox (LBX) format DVD title, please change the format to Letterbox (LBX) in the projector OSD.

****** Page 42 ****** 32 9 10 11 Image is too small or too large Image has slanted sides Image is reversed Adjust the zoom ring on the projector. Move the projector closer to or further from the screen. Press “MENU” on the remote control. Go to “Image – -> Aspect Ratio” and try different settings or press ” RATIO” on the remote control to adjust directly. If possible, reposition the projector so that it is centered on the screen. Press the Keystone / button on the remote control until the sides are vertical. Select “Image –> Projection Mode” on the OSD and adjust the projection direction.

****** Page 43 ****** OSD Messages Condition Message • 33 Message Reminder Fan Fail – the system fan is not working Fan Fail. Lamp will automatically turn of soon. Projector Overheated – the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Please check the following message. Projector overheated, system will turn off automatically soon, please: I, Check If operation amblent temperature between 5 degree and 40 degree, 2. Check if filter needs to be cleaned. 3. Check if inlet or outlet is blocked. 4. Check if high altitude mode is set when the projector operating at high altitude area. Please also check the dust filters if they are installed. If the dust filter is clogged with dust, please clean it. Please refer to “Cleaning and replacing the dust filters (Option)” for details. • Replace the lamp – the lamp is about to reach its maximum lifetime. Prepare to replace it soon. Lamp is approaching the end of its useful life in full power operation. Problems with the Projector 2 Condition The projector stops responding to all controls Lamp burns out or makes a popping sound Replacement suggested! Solution If possible, turn off the projector, then unplug the power cord and wait at least 30 seconds before reconnecting power. When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the “Replacing the Lamp” section.

****** Page 44 ****** 34 LED & Alarm Definition Listing LED Messages Message Input power plug Standby Power button ON Lamp retry Power off (Cooling state) Power button OFF (cooling completed; standby mode) Error (thermal failure) Error (fan lock) Error (lamp breakdown) Error (color wheel fail) Lamp_LED Red Flash ON to OFF IOOms ON Qu ick Flashing Temp_LED Red Flash ON to OFF IOOms ON Qu ick Flash ing Power LED Red Flash ON to OFF IOOms ON Quick Flashing ON Blue ON Qu ick Flashing ON ON ON ON

****** Page 45 ****** 35 Cleaning and replacing the dust filters (Option) Cleaning the dust filters Clean the dust filters after every 1000 hours of use. If they are not cleaned periodically, they can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. 1 Follow these steps: 1 2 3 4 5 Turn the projector off. Wait for the Power LED to stop flashing then unplug the power cord Allow the projector at least 30 mins to cool down. Pull out the dust filter. (Illustration #1) To clean the dust filters, use a small vacuum cleaner designed for computers and other office equipment. (Illustration #2) If the dirt is difficult to remove or the filter is broken, please contact your local dealer or service center to obtain a new filter.

****** Page 46 ****** 36 Replacing the Lamp Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp. The projector will detect the lamp life. You will be shown a warning message ” Lamp is approaching the end of its useful life in full power operation. Replacement suggested! ” When you see this message, change the lamp as soon as possible. Make sure the projector has been cooling down for at least 30 minutes before changing the lamp. Warning: The lamp compartment is hot! Allow it to cool down before changing the lamp. 1 33 2 To Change the Lamp Turn off the projector by pressing the Power button. Allow the projector at least 30 minutes to cool down. Disconnect the power cord. 1 2 3 Use a screwdriver to remove the screw from the cover. (Illustration #1) Push to the direction of the arrow. (Illustration #2) Push up the cover. (Illustration #3) Remove the screw that secure the lamp module. (Illustration #4) Pull out the lamp plug. (Illustration #5) Lift the handle so that it stands up. (Illustration #6) Lift the handle so that it stands up. Pull out the lamp module by force. (Illustration #7) To replace the lamp module, use a new lamp and reverse the above steps.

****** Page 47 ****** 37 Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.

****** Page 48 ****** 38 Ceiling Mount Installation If you wish to install the projector using a ceiling mount, please refer to the steps below: 1 2 Drill four holes into a solid, structural ceiling member, and secure the ceiling mount base to the ceiling Choose the length combination based on actual environment. (CM-OIS doesn’t include Type 2 and Type 3.) Type I Type 2 Type 3

****** Page 49 ****** 3 4 39 Type 1: For the standard size use three bracket screws to mount the projector to the ceiling mount bracket. Type 2 and Type 3: Alternatively, for the larger size, use the sliding extensions for more supports. Type 1: Type 2: Type 3: Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution. Connect the main body connector to the projector bracket (illustration 1), and then screw up four screws (illustration 2). Illustration 1 Illustration 2

****** Page 50 ****** 40 5 Adjust the angle and positioning as necessary. 3600 Screw Type B Diameter (mm) 4 Washer Type Length (mm) 25 Large 55 m Small SCREW SPEC. M4 x 25 mm 0} O rnrn

****** Page 51 ****** 41 Specifications The specifications listed below are subject to change without notice. For final specs, please refer to Acer’s published marketing specifications. Projection system Resolution Computer compatibility Video compatibility Aspect ratio Displayable colors Optical zoom ratio Throw ratio Projection lens Projection screen size (diagonal) Projection distance Horizontal scan rate DLP@ • X1126H/D506D/EV-S57HN26S/AS600/DSV1610 series: 800×600 SVGA resolution • X1226H/D516D/EV-X57HN26X/AX600/DNX1609 series: 1024×768 XGA resolution • X1326WH/D526D/EV-W57HN26W/AW600/ DWX 1608 series: 1280×800 WXGA resolution IBM PC and compatibles, Apple Macintosh, iMac and VESA standards: SXGA, XGA, VGA, SVGA, SXGA+, WXGA, WXGA+, WSXGA + NTSC (3.58/443), PAL (B/D/G/H/I/WN), SECAM (B/D/G/ K/KI/L), HDTV (720p, 1080i, 1080p), EDTV (480p, 576p), SDTV (480i, 576i) Auto, Full, 4:3, 16:9, L Box 1.07 billion colors • X1126H/D506D/EV-S57HN26S/AS600/DSV1610/ X 1226H/D516D/EV-X57HN26X/AX600/DNX1609 series: 1.94 -2.16 (5 1 • X1326WH/D526D/EV-W57HN26W/AW600/ DWX1608 series: 1.54 1.72 • X1126H/D506D/EV-S57HN26S/AS600/DSV1610/ X 1226H/D516D/EV-X57HN26X/AX600/DNX 1609 series: F = 2.41 2.53, f — 21.85mm 24.01mm, Manual Zoom & Focus • X1326WH/D526D/EV-W57HN26W/AW600/ DWX 1608 series: F = 2.50 2.67, f – 21.86mm 24.00mm, Manual Zoom & Focus • X1126H/D506D/EV-S57HN26S/AS600/DSV1610/ X 1226H/D516D/EV-X57HN26X/AX600/DNX1609 series: 23″ 300″ (58cm -762cm) • X1326WH/D526D/EV-W57HN26W/AW600/ DWX1608 series: 27″ 300″ (69m 762cm) • X1126H/D506D/EV-S57HN26S/AS600/DSV1610/ X 1226H/D516D/EV-X57HN26X/AX600/DNX 1609 series: 1.0m 11.8m (3.3′ 38.7′) • X1326WH/D526D/EV-W57HN26W/AW600/ DWX1608 series: 1.0m 10.0m (3.31 32.8′) 15 – 100 kHz

****** Page 52 ****** 42 Vertical refresh scan rate Lamp type Keystone correction Audio Weight Dimensions (W x D x H) Digital zoom Power supply Power consumption Operating temperature Standard package contents 1/0 connectors Power socket VGA IN 1 VGA IN 2 VGA output Composite video S-Video HDMI 2 HDMI I/MHL RS232 3.5 mm audio jack input 1 3.5 mm audio jack input 2 3.5 mm audio jack output 5V DC output 24- 120 Hz 220 W user-replaceable lamp ±40 degrees Internal speaker with 3 W x 1 output 2.65 Kg (5.8 lbs) 315 mm X 214 mm X 98 mm (12.4″ x 8.4″ x 3.8″) AC input 100 – 240 V auto-switch ing power supply Normal mode: 260W ± @ IIOVAC ECO mode: 200W ± @ 1 IOVAC Standby mode < 0.5W OOC to / to 1040F AC power cord xl • VGA cable xl Remote control xl AAA battery x2 (for remote control) (option) User's gu ide (CD-ROM) xl (option) Quick start guide xl Security card xl (option) Dust filters xl (option) Carrying case xl (option) X 1126 H/X 1226H/X1326WH/D506D/D516D/D526D/EV-S57H/ EV-X57H/EV-W57H/ V26SN26XN26W/AS600/AX600/AW600/DSV1610/DNX1609/ DWX1608 Note: Design and specifications are subject to change without notice. ****** Page 53 ****** Compatibility modes A. VGA Analog VGA Analog PC Signal 1 Modes VGA SVGA XGA SXGA QuadVGA SXGA+ UXGA PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 i Mac DV (G3) Resolution 640×480 640×480 640×480 640×480 640×480 800×600 800×600 800×600 800×600 800×600 800×600 1024×768 1024×768 1024×768 1024×768 1024×768 1152×864 1 152×864 1 152×864 1280×1024 1280×1024 1280×1024 1280×1024 1280×960 1280×960 1400×1050 1600×1200 640×480 640×480 800×600 1024×768 1152×870 1280×960 1024×768 V.Frequency [Hz] 60 72 75 85 120 56 60 72 75 85 120 60 70 75 85 120 70 75 85 60 72 75 85 60 75 60 60 60 66.6(67) 60 60 75 75 75 43 H.Frequency [KHz] 31.5 37.9 37.5 43.3 61.9 35.1 37.9 48.1 46.9 53.7 77.4 48.4 56.5 60.0 68.7 99.0 63.8 67.5 77.1 64.0 77.0 80.0 91.1 60.0 75.2 65.3 75.0 31.4 34.9 37.9 484 68.7 75.0 60.0 ****** Page 54 ****** 44 2 3 1 VGA Analog – Extended Wide timing Modes WXGA WSXGA+ WUXGA VGA Analog Modes 480i 576i 480p 576p nop 720p 1080i 1080i 1080p 1080p 1080p Resolution 1280×768 1280×768 1280×768 1280×720 1280×720 1280×800 1280×800 1920×1200 1440×900 1680×1050 1920×1080 (1080P) 1366×768 1920×1200-RB V.Frequency [Hz] 60 75 85 60 120 60 119.909 60 60 60 60 60 59.94 Component Signal Resolution 720×480(1440×480) 720×576(1440×576) 720×480 720×576 1280×720 1280×720 1920×1080 1920×1080 1920×1080 1920×1080 1920×1080 B. HDMI Digital HDMI – PC Signal Modes VGA SVGA Resolution 640×480 640×480 640×480 640×480 640×480 800×600 V.Frequency [Hzl 59.94 (29.97) 50(25) 59.94 50 60 50 60(30) 50(25) 23.97/24 60 50 V.Frequency [Hz] 60 72 75 85 120 56 H.Frequency [KHz] 47.8 60.3 68.6 44.8 92.9 49.6 101.6 74 59.9 65.3 67.5 47.7 74.04 H.Frequency [KHz] 15.7 15.6 31.5 31.3 45.0 37.5 33.8 28.1 27.0 67.5 56.3 H.Frequency [KHz] 31.5 37.9 37.5 43.3 61.9 35.1 ****** Page 55 ****** XGA SXGA QuadVGA SXGA+ UXGA PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 PowerBook G4 i Mac DV (G3) 800×600 800×600 800×600 800×600 800×600 1024×768 1024×768 1024×768 1024×768 1024×768 1152×864 1152×864 1152×864 1280×1024 1280×1024 1280×1024 1280×1024 1280×960 1280×960 1400×1050 1600×1200 640×480 640×480 800×600 1024×768 1152×870 1280×960 1024×768 2 HDMI – Extended Wide timing Modes WXGA WSXGA+ Resolution 1280×768 1280×768 1280×768 1280×720 1280×720 1280×800 1280×800-RB 1440×900 1920×1200 1680×1050 60 72 75 85 120 60 70 75 85 120 70 75 85 60 72 75 85 60 75 60 60 60 66.6(67) 60 60 75 75 75 V.Frequency [HzJ 60 75 85 60 120 60 119.909 60 60 60 45 37.9 48.1 53.7 77.4 48.4 56.5 60.0 68.7 99.0 63.8 67.5 77.1 64.0 77.0 80.0 91.1 60.0 75.2 65.3 75.0 31.4 34.9 37.9 48.4 68.7 75.0 60.0 H.Frequency [KHz] 47R 60.3 68.6 44.8 92.9 49.6 101.6 59.9 74 65.3 ****** Page 56 ****** 46 3 4 WUXGA 920x 1080 (1080P) 1366×768 1920×1200-RB HDMI Video Signal Modes 480i 576i 480 576 720 nop 1080i 1080i 1080p 1080p 1080 1080p Resolution 720×480(1440×480) 720×576(1440×576) 720×480 720×576 1280×720 1280×720 1920×1080 1920×1080 1920×1080 1920×1080 1920×1080 1920×1200-RB HDMI – 1.4a 3D Timing Modes 720 (Frame Packing) 720p (Frame Packing) 1080 (Frame Packin ) 720 (Frame Packing) 720p (Frame Packing) 1080i (Top and Bottom) 1080i (To and Bottom) 1080 (To and Bottom) 1080p (Top and Bottom) 1080p (Top and Bottom) 720 (Sideb Side (Half)) 1080i (Sideb Side (Half)) 1080i (Side by Side (Half)) 1080 (Sideb Side (Half) 1080p (Sideb Side (Half) Resolution 1280 x 720 1280 x 720 1920 x1080 1280 x 720 1280 x 720 1920 x1080 1920 x1080 1920 x1080 1920 x1080 1920 x1080 1280 x 720 1920 x1080 1920 x1080 1920 x1080 1920 x1080 60 60 59.94 V.Frequency [Hzl 59.94 (29.97) 50(25) 59.94 50 60 50 60(30) 50(25) 23.97/24 60 50 59.94 V.Frequency [Hz] 50 60 24 50 60 50 (25) 60 (30) 24 50 60 60 50 (25) 60 (30) 50 60 67.5 47.7 74.04 H.Frequency [KHz] 15.7 15.6 31.5 31.3 45.0 37.5 33.8 28.1 27.0 67.5 56.3 74.04 H.Frequency [KHz] 37.5 45 .o 27 .o 37.5 45.0 28.1 33.8 27.0 56.3 67.5 45 .o 28.1 33.8 56.3 67.5 ****** Page 57 ****** Graphic source monitor range limits C. MI-IL Digital Modes VGA 480i 576i 15.6 480p 480p_2x 576 576p_2x 720p 720p 1080i 1080i 1080p 1080 1080p Horizontal scan rate: Vertical scan rate: Max. pixel rate: V.Frequency 47 15k-100kHz 24-120 Hz Ana og:165MHz Digital:165MHz H.Frequency [KHz] Resolution 640×480 720×480 (1440×480) 720×576 (1440×576) 720×480 720×576 1440×576 1280×720 1280×720 1920×1080 1920×1080 1920×1080 1920×1080 1920×1080 Horizontal scan rate: Graphic source monitor Vertical scan rate. range limits Max. pixel rate: 59.94/60 59.94/60 50(25) 59.94/60 59.94/60 50 50 59.94/60 50 60(30) 50(25) 23.97/24 25 29.97/30 31.5 31.5 31.5 31.3 31.3 45.0 37.5 33.8 28.1 27.0 28.1 33.8 15k-50 kHz 24-60 Hz Digital: 75 MHz Note 1: Note 2: Functions vary depending on model definition. MHL 1080p 3D 24p frame packing is not supported. ****** Page 58 ****** 48 Regulations and safety notices FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the device and receiver. Connect the device into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Notice: Peripheral devices Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this device. Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003. ****** Page 59 ****** 49 Remarque Ilintention des utilisateurs canadiens Cet appareil numérique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries Acer hereby declares that this projector series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Compliant with Russian regulatory certification 001 Radio device regulatory notice Note: The regulatory information below is for models with wireless LAN and/or Bluetooth only. General This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules). Canada — Low-power license-exempt radio communication devices (RSS-247) a b Common information Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Operation in 2.4 GHz band To prevent radio interference to the licensed service, this device is intended to be operated indoors and installation outdoors is subject to licensing. List of applicable countries This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact the local office in the country of use. Please see ec.europa.eu/enterprise/rtte/implem.htm for the latest country list. ****** Page 60 ****** Acer Incorporated 8F,. 88, l, XintaJ 5th Rd., Xizhi New TailMÅ City 221, Tarwan Declaration of Conformity we, Acer Incorporated 8F, 88, Sec. l, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan And, Acer Italy s.r.l. Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 No, 1275/2008, EN 505642011 acer.it Product: Trade Name: Model Number: DLP Projector Acer DSV1610/DNX160WDWX1608 X 1126WX1226WX1326WH/D506D/D516D/D526D/EV-S57WEV-X57W EV-W57WV26S/V26X/V26W/AS600/AX600/AW600 We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in conformity with the relevant Union harmonization legislations as below Directive and following harmonized standards and/or other relevant standards have been applied: EMC Directive: 2014/30/EU EN Class B EN o .R&TI'E Directive: 1999/5/EC (until Jun 12, 2017) RED Directive: 2014/53/ECJ From Jun 13 201 EN 61000-322014, A EN EN 300 328 V IRI o EN 301 893 Vl.7.1 EN 300 Vlß,l o EN 300 440-2 Vl.4.1 o EN 302 291-1 Vl.l.l o EN 302 291-2 IND Directive: 2014/35/F,U EN 050-1 o EN 50332-1:2000 RoHS Directive: 2011/65/EU EN 50581 @ Erp 2009/125/EC Regulation (ELI) No. 617/ 2013 Rc lation o EN 301 511 o EN 301 908-1 V62.1 EN 301 V621 o EN 301 908-13 V6.2.1 o EN 301 489-1 VI .92 o EN 301 489-3 VI EN 50332-2:2003 EN 301 489-7 o EN 301 489-17 V2.2.1 EN 301 4W24 VIS.I o o EN EN 50566:2013 o o EN 62479:2010 EN o EN 62209-12006 0 EN 62209-22010 Regulation (EC) No. 278/2009; EN 505632011 Year to begin affixing CE marking 2016. R Jan r. Manager Acer Incorporated (Taipei, Taiwan) Dec. 22 2016 Date ****** Page 61 ****** Acer America Corporation 333 West San Carlos St., Suite 1 5(H) San Jose, CA 95110 US. A. Tel: 254-2984000 Fax: 254-298-4147 w•ww-acctMYtn Federal Communications Commission Declaration of Conformity This device complies with Part 15 of thc FCC Rules. Operation is subject to thc following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following local Manufacturer / Importer is responsible for this declaration: Product: Model Number: Machine Type: Name of Responsible Party: Address of Responsible Party: Contact Person: Phone No.: Fax No.: DLP Projector DSV1610/DNX1609/DWX1608 x 1126WX1226WX1326WWD506D/D516D/D526D/ EV-S57H/EV-X57H/EV-W57H/V26S/V26X/V26W/ AS600/AX600/AW600 Acer America Corporation 333 West San Carlos St. Suite 1500 San Jose, CA 95110 U.S.A. Acer Representative 254-298-4000 254-298-4147


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

ACER EV-X57H (01) PDF MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.