Post questions, comments, reviews or page errors in the comment box below.

Click here to download ACER CM2241W (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** Acer LCD Monitor Userls Guide

****** Page 2 ****** Copyright 0 2019. Acer Incorporated. All Rights Reserved. Acer LCD Monitor User’s Guide Original Issue: 11/2019 Changes may be made periodically to the information in th is publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose. Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your computer. All correspondence concerning your unit should include the serial number, model number and purchase information. No part of th is publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electron ically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated. Acer LCD Monitor User’s Guide Model number: Serial number: Date of purchase: Place of purchase: Acer and the Acer logo are registered trademarks of Acer Incorporated. Other compan iesl product names or trademarks are used herein for identification purposes only and belong to their respective companies.

****** Page 3 ****** iii Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD screen has 99.99% or more effective pixels. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all the time. Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the power switch for a few hours. Acer monitor is purposed for video and visual display of information obtained from electronic devices. Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product Cleaning your monitor Please carefully follow these guidelines when cleaning the monitor: • Always unplug the monitor before cleaning • Use a soft cloth to wipe the screen and cabinet front and sides. Connecting/disconnecting the device Observe the following guidelines when connecting and disconnecting power from the LCD monitor: Make sure the monitor is attached to its base before connecting the power cord to the AC power outlet. Make sure both the LCD monitor and the computer are turned off before connecting any cable or unplugging the power cord. If the system has multiple sources of power, disconnect power from the system by unplugging all power cords from the power supplies.

****** Page 4 ****** Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To protect your hearing, follow these instructions. Gradually increase the volume until you can hear it clearly and comfortably and without distortion. After setting the volume level, do not increase it after your ears have adjusted. Limit the amount of time listening to music at high volume. Avoid turning up the volume to block out noisy surroundings. Turn the volume down if you can’t hear people speaking near you. Warnings Do not use this product near water. Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged. Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product. To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface. Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage internal devices. Using electrical power This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company. Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord. If an extension cord is used with this product, make sure that the total

****** Page 5 ****** ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip’s input rating This product’s power cord is equipped with a three-wire grounded plug. The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the power cord plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details. Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury. Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product. Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, type SPT-2, rated 7 A 125 V minimum, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length. Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service personnel when: the power cord or plug is damaged, cut or frayed liquid was spilled into the product the product was exposed to rain or water the product has been dropped or the case has been damaged the product exhibits a distinct change in performance, indicating a need for service the product does not operate normally after following the operating instructions

****** Page 6 ****** vi Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Potentially explosive environments Switch off your device in any area with a potentially explosive atmosphere and obey all signs and instructions. Potentially explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Switch off the device near gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage and distribution areas; chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not always, marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust or metal powders. Additional safety information Your device and its enhancements may contain small parts. Keep them out of the reach of small children. IT Equipment Recycling Information Acer is strongly committed to environmental protection and views recycling, in the form of salvaging and disposal of used equipment, as one of the company’s top priorities in minimizing the burden placed on the environment. We at Acer are very conscious of the environmental effects of our business and strive to identify and provide the best working procedures to reduce the environmental impact of our products. For more information and help when recycling, please go to this website: acer-group.com/publicßustainability/ Visit acer-group ecom for further information on the features and benefits of our other products.

****** Page 7 ****** Vli Disposal instructions Do not throw this electronic device into the trash when discarding To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit acer-group.com/public/Sustainabilitv LCD pixel statement The LCD unit is produced with high-precision manufacturing techniques. Nevertheless, some pixels may occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not constitute a malfunction.

****** Page 8 ****** vili This product has been shipped enabled for power management: Activate the Display Sleep mode within 5 minutes of user inactivity. Wake the monitor when it is in Active Off mode, move the mouse or press any keyboard key. Tips and information for comfortable use Computer users may complain of eyestrain and headaches after prolonged use. Users are also at risk of physical injury after long hours of working in front of a computer. Long work periods, bad posture, poor work habits, stress, inadequate working conditions, personal health and other factors greatly increase the risk of physical injury. Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis, tenosynovitis or other musculoskeletal disorders. The following symptoms may appear in the hands, wrists, arms, shoulders, neck or back: • numb ness, or a burning or tingling sensation aching, soreness or tenderness pain, swelling or throbbing stiffness or tightness coldness or weakness If you have these symptoms, or any other recurring or persistent discomfort and/or pain related to computer use, consult a physician immediately and inform your company’s health and safety department. The following section provides tips for more comfortable computer use. Finding your comfort zone Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest, or raising your sitting height to achieve maximum comfort. Observe the following tips: refrain from staying too long in one fixed posture avoid slouching forward and/or leaning backward stand up and walk around regularly to remove the strain on your leg muscles

****** Page 9 ****** ix Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain. Eyes Rest your eyes frequently. Give your eyes regular breaks by looking away from the monitor and focusing on a distant point. Blink frequently to keep your eyes from drying out. Display Keep your display clean. Keep your head at a higher level than the top edge of the display so your eyes point downward when looking at the middle of the display. Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graphics clarity. Eliminate glare and reflections by: placing your display in such a way that the side faces the window or any light source minimizing room light by using drapes, shades or blinds using a task light changing the display’s viewing angle using a glare-reduction filter using a display visor, such as a piece of cardboard extended from the display’s top front edge Avoid adjusting your display to an awkward viewing angle. Avoid looking at bright light sources, such as open windows, for extended periods of time. Developing good work habits Develop the following work habits to make your computer use more relaxing and productive: • Take short breaks regularly and often. Perform some stretching exercises. Breathe fresh air as often as possible. Exercise regularly and maintain a healthy body.

****** Page 10 ****** TABLE OF CONTENTS UNPACKING ATTACHING / REMOVING THE BASE SCREEN POSITION ADJUSTMENT CONNECTING THE POWER CORD SAFETY PRECAUTION CLEANING YOUR MONITOR POWER SAVING CONNECTOR PIN ASSIGNMENT Standard Timing Table INSTALLATION……………………………………………………………………………. 9 USER CONTROLS TROUBLESHOOTING 10 .21

****** Page 11 ****** UNPACKING Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. LCD Monitor DP Cable (Optional) Quick Start Guide HDMI Cable (Optional) 0 EN-I AC Power Cord USB Cable (Optional)

****** Page 12 ****** A TTACH/NG/RFMOV/NG THE BASE Note: Remove the monitor and monitor base from its packaging. Carefully place the monitor face-down on a stable surface — use a cloth to avoid scratching the screen. 2. Attach the stand arm and the base Ensure that the base is screwed tight to the monitor, as illustrated. onto the monitor stand arm. a 9 Note: If installing with a wall mounting kit, it is recommended to use VESA mounting kit (100mm x 100mm) with M4x 10 (L) mm screws to fix your monitor on the wall. EN-2

****** Page 13 ****** SCREEN POS/T/ON ADJUSTMENT In order to optimize the best viewing position, you can adjust the height/tilt of the monitor. Tilt Please see the illustration below for an example of the tilt range. Only at the highest point can 25 degrees of recline be offered for the angle of elevation. 50 250 Height Adjustment After pressing the top of the monitor then you can adjust the height of the monitor. 120 mm EN-3

****** Page 14 ****** Monitor Pivot Before rotating the display, lift it to the top position and then push it back to the utmost degree. Rotate until the monitor stops at 900. a 250 120mm Swivel -900 900 With the built-in pedestal, you can swivel the monitor for the most comfortable viewing angle. O -3600 EN-4 3600

****** Page 15 ****** CONNECTING THE POWER CORD Check first to make sure that the power cord you use is the correct type required for your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V AC voltage area. No user-adjustment is required. Plug one end of the power cord to the AC inlet, and plug the other end into an AC outlet. For unit using at 120 V AC: Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/ 125 V. For unit using at 220/240 V AC (outside of U.S.): Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed. SAFETY PRECAUTION Avoid placing the monitor, or any other heavy object, on the power cord to avoid damage to the cable. Do not expose the monitor to rain, excessive moisture, or dust. Do not cover the ventilation slots or openings of the monitor. Always put the monitor in a place where there is adequate ventilation. Avoid placing the monitor against a bright background or where sun-light or other light sources may reflect on the face of the monitor. Place the monitor just below eye level. Handle with care when transporting the monitor. Refrain from giving shock or scratch to the screen, as screen is fragile. In order to prevent damage to the monitor, do not lift the monitor by its base. CLEANING YOUR MONITOR Please carefully follow the below guidelines when cleaning the monitor. Always unplug the monitor before cleaning. Use a soft cloth to gently wipe the screen and cabinet front and sides. NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE. PLEASE DO NOT USE ANY AMMONIA OR ALCOHOL-BASED CLEANERS ON THE LCD DISPLAY SCREEN OR CASE. Acer will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners. EN-5

****** Page 16 ****** POWER SA V/NG The monitor will be driven into “Power Saving” mode by the control signal from the display controller, as indicated by the blinking amber power LED. State ON LED Light Amber Power Saving Mode Blinking amber The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from Active OFF state back to ON state is around 3 seconds. DDC To make your installation easier, the monitor is able to Plug and Play with your system if your system also supports DDC protocol. The DDC (Display Data Channel) is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The monitor supports DDC2B standard. EN-6

****** Page 17 ****** CONNECTOR P/N ASSIGNMENT 19-Pin Color Display Signal Cable PIN 2. 3. 4. 5. 6. 7. 8. 9. Meaning TMDS Data2+ TMDS Data2 Shield TMDS Data2- TMDS Datal+ TMDS Datal Shield TMDS Datal- TMDS DataO+ TMDS DataO Shield TMDS DataO- 20-Pin Color Display Signal Cable* PIN 2. 3. 4. 5. 6. 7. 8. 9. 10. Description Lane0(p) GND Lane0(n) Lanel(p) GND Lanel(n) Lane2(p) GND Lane3(n) Lane3(p) PIN 10. 11. 12. 13. 14. 15. 16. 18. 19. PIN 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 191715131197531 18161412108642 Meaning TMDS Clock* TMDS Clock Shield TMDS Clock- CEC Reserved (N.C. on device) SCL SDA DDC/CEC Ground +5V Power Hot Plug Detect Description GND Lane3(n) Configl Config2 AUX_CH (n) GND AUX_CH (p) Hot Plug Detect DP Power Return DP Power * only for certain models

****** Page 18 ****** Standard Timing Tab/e 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Mode VGA VGA VGA MAC VESA SVGA SVGA SVGA SVGA MAC XGA XGA XGA MAC VESA VESA SXGA SXGA VESA WXGA WXGA+ WSXGA+ UXGA UXGA Resolution 640 x 480 640 x 480 640 x 480 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1 152 x 870 1 152 x 864 1280 x 960 1280 x1024 1280 x1024 1280 x 720 1280 x 800 1440 x 900 1680 x 1050 1920 x 1200 1920 x 1200 Remark 60 Hz 72 Hz 75 Hz 66.66 HZ 70 Hz 56 Hz 60 Hz 72 Hz 75 Hz 74.55 Hz 60 Hz 70 Hz 75 Hz 75 Hz 75 Hz 60 Hz 60 Hz 75 Hz 60 Hz 60 Hz 60 HZ 60 Hz 60 Hz 75 Hz Note: The DisplayPort of this monitor is purposely supporting the Adaptive-Sync support technology and targeting AMD graphic solutions. Adaptive-Sync supported AMD GPUs: AMD RadeonTM R7 260 series and R9 290 series graphic cards. For other GPUs, please contact the graphic card manufactures whether they can support or not. EN-8

****** Page 19 ****** INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps 1. 1-1 Connect HDMI Cable (Only HDMI-input model) a. Make sure both the monitor and computer are powered-OFF. b. Connect the HDMI cable to the computer. 1-2 Connect DP Cable (Only DP-input model) a. Make sure both the monitor and computer are powered-OFF. b. Connect the DP cable to the computer. 2. Insert the monitor power cable into the power port at the back of the monitor. 3. Plug the power cords of your computer and your monitor into a nearby electrical outlet. 4. Select Power-off USB charge ON/OFF to enable/disable Power-off USB charge function. (Optional) Ill I HDMI HDMI o optional Note: Adjustment of the volume control as well as the equalizer to other settings than the center position may increase the ear-/ headphones output voltage and therefore the sound pressure level. EN-9

****** Page 20 ****** USER CONTROLS Base Controls No. 1 2 3 4 1 2 3 4 Item Power button/indicator Hotkey 1, 2 buttons Input button Navi/OK button 1 Description Turns the monitor on/off. Amber indicates power on. Blinking amber indicates standby/power saving mode. Press to activate user defined hotkey function. Press to toggle input sources. Press to activate the OSD menu, then use it as directional key to highlight the desired function. Press it again to enter a selection. EN-IO

****** Page 21 ****** Adjusting the OSD settings Note: The following content is for general reference only. Actual product specifications may vary. Note: This product qualifies for ENERGY STAR in the “factory default” setting and this is the setting in which power savings will be achieved. Changing the factory default picture settings or enabling other features will increase power consumption that could exceed the limits necessary to qualify for ENERGY STAR rating. The OSD (on-screen displ ay) can be used for adjusting the settings of your LCD Monitor. Press the MENU button to open the OSD. You can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings, please refer to following page: Main Page The default function for buttons 1 and 2 are Modes and Brightness. You can use the Hot Key Assignment function to set these buttons to your preferred functions. Concept D Modes Standard Brightness Input HDMI 2 Menu 1. 2. 3. 4. Modes Brightness Input Menu EN-II

****** Page 22 ****** Adjusting the Modes From any function page, press to open the Modes control and select which user-defined profile to use (please see The Function page section for more information). Calibration 1 Calibration •JD Move sRGB Stanaard 0K OCI-P3 CAD/CAM AdobeRGB Graphics User M Ovie Adjusting the Brightness Open the Brightness control and select the brightness setting using the Navi/ 0K button. When you are done, press the Navi/OK button to exit. Brightness Adjust 0K Selecting the Input Open the Input control and select the desired input. You can also toggle Auto Source On or Off. When you are done, use the Navi/OK button to exit. Input Auto Source Masee HDMI 2 EN-12

****** Page 23 ****** The Function page Open the Function page to select a menu function, and adjust the settin s which you want using the Navi/OK button. When you are done, press to exit. You can also press from any function page to select your preferred Mode. Adjusting the Picture Mode – Standard Picture Color 4)) Audo PerfOrma-.ee Move & ightness COntrast Blue Light Black ShMpness • Ent« 2. 3. 4. Press the MENU button to open the OSD. Using the Navi/OK button, select Picture from the OSD. Then navigate to the setting you wish to change. Use the Navi/OK button to select the setting. Brightness: Adjust the brightness from 0 to 100. Note: Adjusts the balance between light and dark shades. 5. Contrast: Adjust the contrast from 0 to 100. Note: Sets the degree of difference between light and dark areas. Blue Light: Filter out blue light by adjusting different Blue Light showing 6. ratio – 80%, 70%, 60%, 50%. Note: Higher values allow more blue light through. For the best protection, select a lower value. EN-13

****** Page 24 ****** 8. 9. Black Boost: This boosts the amplitude of the dark color levels of the display— blacks will be less black. The higher the level, the higher the boost. ACM: Turn ACM On or Off. The default is Off. Super Sharpness technology can simulate high-resolution images by boosting the pixel density of the original source. It can make images sharper and clear. Adjusting the Color Picture C Olor Audio Performance osn System Move Picture Color Audio Cierforrnartce oso System Move Mode – Standard Gamma Color Temp. a Gain G Gain g Gain A Bias G Bias a Bias Enter Mode — Standard Modes Color Space Calibration Grayscale Mode 6—axis Hue E—axis Saturate Enter Warm General Off 2. 3. 4. Press the MENU button to open the OSD. Using the Navi/OK button, select Color from the OSD. Then navigate to the setting you wish to change. Use the Navi/OK button to select the setting. Gamma mode allows you to adjust the luminance tone. The default value is 2.2 (standard value for Windows). EN-14

****** Page 25 ****** 5. 6. 7. 8. 9. 10. 11. 12. Color temperature: Default is warm. You can choose Cool, Warm, Normal, Bluelight or User. Uniformity: Turn the Uniformity function On or Off. Modes: Select your preferred mode. Color Space: You can choose General, SMPTE-C, EBU, Rec. 709, DCI-P3, sRGB or AdobeRGB. Note: If Color Space is “DCI-P3”, “sRGB” or “AdobeRGB then Modes is 1. respectively set to “DCI-P3″, ” sRGB” or “AdobeRGB” automatically. 2. If Color Space is not “DCI-P3”, “sRGB” or “AdobeRGB”, then Modes is set to “Standard”. Calibration: Calibrate the color of your monitor to the selected Color Space setting. Grayscale Mode: Turn grayscale mode On or Off. 6-axis Hue: Adjust the red, green, blue, yellow, magenta and cyan hue. 6-axis Saturate: Adjust the red, green, blue, yellow, magenta and cyan saturation. EN-15

****** Page 26 ****** Adjusting the Audio Mode — Standard Audio OSO • Wlove Mute • Enter 1. 2. 3. 4. 5. Press the MENU button to open the OSD. Using the Navi/OK button, select Audio from the OSD. Then navigate to the setting you wish to change. Use the Navi/OK button to select the setting. Volume: Adjust the volume. Mute: Select On or Off. EN-16

****** Page 27 ****** Adjusting the Performance Mode — Standard ) AL.Hio Performance OSO • Wlove Over Drive Refresh Rate Num • Enter 1. 2. 3. 4. 5. 6. 7. Press the MENU button to open the OSD. Using the Navi/OK button, select Performance from the OSD. Then navigate to the setting you wish to change. Use the Navi/OK button to select the setting. Over Drive: Select Off, Normal, or Extreme. Adaptive-Sync: Select On or Off. Adaptive-Sync is available for AMD supported graphic cards only. Refresh rate num: Display the panel’s current refresh rate on the screen. VRB: When VRB is Extreme or Normal, VRB provides a sharper and clearer dynamic picture; the default is Off. VRB does not support PIP/PBP Mode and HDR Mode. (Selective models) When VRB is Extreme or Normal, Adaptive-Sync is automatically turned off. VRB will affect the brightness of the following: Logo, Aim Point, Message and Input Icon. VRB feature is dependent on the monitor’s maximum refresh rate. For monitors supporting up to 75 Hz, VRB is available when the refresh rate is set to 75 Hz only. EN-17

****** Page 28 ****** 8. Ultra-Low Latency: Select On to speed up the processing time of the display switching process. Note: If Adaptive-Sync is “ON”, then the Ultra-Low Latency is 1. automatically turned On and grayed out. 2. Ultra-Low Latency is not supported at resolutions below 800 x 600. Adjusting the OSD Mode – Stat-Ord oso Picture Color AR.K1io System tel-ave English OSO Timeout Tiansparene•.g • •y Enter 10 2. 3. 4. 5. 6. 7. Press the MENU button to open the OSD. Using the Navi/OK button, select OSD from the OSD. Then navigate to the setting you wish to change. Use the Navi/OK button to select the setting. Language: Set the OSD menu language. OSD timeout: Adjust the delay before turning the off the OSD menu. Transparency: Select the transparency of the OSD menu. The transparency can be ()% (OFF), 20%, 40%, 60%, or 80%. OSD Lock: OSD Lock function is used to prevent OSD button from being pressed acciedntally. To remove the OSD Lock message, press and hold the Navi/OK button continuously for 3 seconds until the message disappears. If the OSD Lock message remains, please check whether the Navi/OK button is stuck. EN-18

****** Page 29 ****** Adjusting the System Picture color Audio ors-o P’ict’.-o•e color Acxjio OSO Wlove — Standard Input Auto %urce OP Format Hot Key AssigrÜnent oocjcr HJOMI Black Level Quick Start Enter — Stat-Ord LEO Control USB • Enter HOMI 2 OP12 Normal 2. 3. 4. 5. 6. 7. 8. 9. Press the MENU button to open the OSD. Using the Navi/OK button, select System from the OSD. Then navigate to the setting you wish to adjust. Use the Navi/OK button to select the setting. Input: Select the source from an available input source. Auto Source: Automatically searches for available input sources. DP Format: You can select which DP format you are using. The default is set at DPI.2. Hot Key Assignment: Select the function of Hot Key 1 or Hot Key 2. Wide Mode: You can select which screen aspect you are using. The options are Full, Aspect and 1:1. DDC/CI: Allows the monitor settings to be set through the software on the PC. EN-19

****** Page 30 ****** 10. 11. 12. 13. HDMI Black Level: You can select the level of blackness under HDMI source. The options are Normal and Low. Quick Start Mode: Enable monitor rapidly. LED Control: Adjust the brightness of the LED light. Power-off USB charge (Optional): Turn On or Off. Product information Information Main Source HDMI a Resolution 1920x10B0 H/V Frequency H:74KHz V:60Hz Mode Normal Series Number MMOOOOOOOB00004F66BSIO Reset All Settings Move From any function page, press i to open Information page. Reset All Settings: Reset all settings to the factory defaults. EN-20

****** Page 31 ****** TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the trouble- shooting list below to see if you can self-diagnose the problem. (HDMI/DP Mode) Problems No Picture Abnormal Sound (Only Audio-lnput model) (Optional) Current Status Amber Off Blinking amber No sound, or sound level is too low EN-21 Remedy Using OSD, adjust brightness and contrast to maximum or reset to their default settings. Check the power switch. Check if AC power cord is properly connected to the monitor. Check if video signal cable is properly connected at the back of monitor. Check if the power of computer system is ON. Check the audio cable with the host PC is connected. Check if the volume setup of the host PC is in minimum position and try to raise the volume level.

****** Page 32 ****** acer Acer Incorporated 8F, 88, Sec I, Xintai 5th Rd , Xizhi New Tåipei City 221, Taiwan Declaration of Conformity we, Acer Incorporated 8F, 88, sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan And, Acer Italy s.r. l. Viale delle Industrie I/A, 20020 Arese (MI), Italy Tel: +39-02-939-921, Fax: +39-02 9399-2913 acer.it Product: Trade Name: Model Number: SKU Number: LCD Monitor ACER CM2241W CM2241W xxxxxx = 0-9, a -z, A -Z, or blank) We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in conformity with the relevant Union harmonization legislations as below Directive and following harmonized standards and/or other relevant standards have been applied: EMC Directive: 2014/30/EU Class B Class B EN61000-3-2:2014 Class D LVD Directive: 2014/35/EU EN 60950-1 :2006/A11 :2009/A1 RoHS Directive: 2011/65/EU EN 50581:2012 ErP Directive: 2009/125/EC Regulation (EC) No. 1275/ 2008; EN 50564:2011 Year to begin affixing CE marking: 2019. RU Jan / Sr. Manager Acer Incorporated (Taipei, Taiwan) EN-22 EN 55024:2010 EN61000-3-3:2013 Nov. 08, 2019 Date

****** Page 33 ****** Acer America Corporation 333 West San Carlos St., Suite 1500 San Jose, CA 95110 Tel : 254-298-4000 Fax : 254-298-4147 acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (l) this device may not cause hannful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following local Manufacturer /lmporter is responsible for this declaration: Product: Model Number: SKU Number: Name of Responsible Party: Address of Responsible Party: Contact Person: Phone No.: Fax No.: LCD Monitor CM2241W CM2241W xxxxxx (“x” = 0—9, a z, or A Z) Acer America Corporation 333 West San Carlos St. Suite 1500 San Jose, CA 95110 Acer Representative 254-298-4000 254-298-4147 EN-23

****** Page 34 ****** ENERGY STAR ENERGY STARO Acer’s ENERGY STAR qualified products save you money by reducing energy costs and helps protect the environment without sacrificing features or performance. Acer is proud to offer our customers products with the ENERGY STAR mark. What is ENERGY STAR? Products that are ENERGY STAR qualified use less energy and prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the U.S. Environmental Protection Agency. Acer is committed to offer products and services worldwide that help customers save money, conserve energy and improve the quality of our environment. The more energy we can save through energy efficiency, the more we reduce greenhouse gases and the risks of climate change. More information refers to energystar.gov. Acer ENERGY STAR qualified products: • Produce less heat and reduce cooling loads, and warmerclimates. • Automatically go into “display sleep” within 5 minutes of inactivity. • Wake the monitor when it is in Active Off mode, move the mouse or press any keyboard key. ENERGY STAR and the ENERGY STAR mark are registered U.S. marks EN-24


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

ACER CM2241W (01) PDF MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.