ACCSOON CINEVIEW HE (01) PDF MANUAL

1. Install the antennas as shown in the picture provided in the PDF.

2. Use the cold shoe mount adapter to install the CineView HE onto the camera or camera cage.

3. Use an NP-F970/F750/F550 battery, DC source or USB-C to power the CineView HE.

4. Connect camera HDMI output to the HDMI IN port on the CineView HE transmitter.

Power On: Press the power on/off button.

Power Off: Hold the power on/off button for 2 seconds.

1. The CineView HE has a group setting knob on both the transmitter and receiver.

2. Set the transmitter and receiver(s) to the same group number using the knob.

3. Devices set to the same group will pair and connect automatically. Devices set to different groups will not pair.

4. To connect multiple receivers (up to 4) to one transmitter, set all receivers and the transmitter to the same group number.

5. If using multiple groups in the same area, ensure each group (transmitter and its receivers) is set to a different group number.

1. If you change the grouping settings after the product has been powered on, a reboot is required for the changes to take effect.

2. After changing the group setting and rebooting, you need to reconnect the transmitter and receiver at close range, otherwise it may fail to pair and connect.

The OLED display shows:

1. Current group number

2. Input audio information

3. Input video information (e.g., FHD 1080p60 H.264)

4. Battery level or DC input status

5. Connection status

6. Current channel (e.g., Auto or a specific channel number)

7. Dual Band (2.4G/5G) status

Transmitter: Shows the number of connected devices. “0” indicates no devices are connected.

Receiver: Shows “1” when connected to the transmitter. Shows “0” if not connected.

1. Press the menu (OK) button to access the menu.

2. Navigate to “Data Rate Setting”.

3. Use the left and right buttons to select the desired mode: High Quality Mode (HQ), Normal Mode (NOM – Default), or Speed Mode (SPD).

4. Press the menu (OK) button to confirm and activate the selected setting.

Note: This setting is only available on the transmitter.

1. Press the menu (OK) button to enter the menu.

2. Navigate to “Channel Setting”.

3. Press the left and right buttons to select the desired channel.

4. Press the menu (OK) button to confirm the selection.

5. Select “Yes” when prompted.

6. Press the menu (OK) button again to confirm. The setting will take effect after the device reboots.

The default channel setting is Auto (A). In this mode, the CineView HE automatically selects the channel with the least interference when powered on.

It is recommended that users do not change this setting unless necessary (e.g., experiencing persistent interference).

Note: This setting is only available on the transmitter.

1. Press the menu (OK) button to enter the menu.

2. Navigate to “Network Reset”.

3. Select “Yes”.

4. Press the menu (OK) button to confirm.

5. Select “Yes” again to confirm the reset.

6. Press the menu (OK) button to reboot. The SSID and password for the 5G WiFi will be reset to factory defaults.

1. Download the App: Download the “Accsoon Go” app from the Google Play Store or iOS App Store.

2. Connect to WiFi: Open the WiFi settings on your mobile device. Find the CineView HE’s WiFi network (named “Accsoon_****” where **** is unique to the product). Select it and enter the default password “12345678” to connect. Note: CineView HE has both 2.4G and 5G signals; ensure you connect to the “Accsoon_****” network.

3. Monitor: Open the Accsoon Go app, select “CineView”, and tap the “Monitor” button.

If you have questions about using the Accsoon Go App, please refer to Accsoon Go App tutorial videos on Accsoon’s official YouTube channel.

1. Ensure you are using the CineView HE receiver, as only it has the UVC out port.

2. Use a Type-C cable (user-provided) to connect the UVC OUT port on the receiver to your mobile phone or computer.

3. Use a streaming platform (e.g., OBS, YouTube) that supports UVC input to start your livestream. The receiver will act as a live camera source.

Note: Support from the live streaming platform is required.

1. Change Transmitter Setting: On the transmitter, access the menu, go to “Data Rate Setting”, use the right button to select “speed mode”, and press the menu button to activate it.

2. Configure App: Open the Accsoon Go app on your mobile device (connected to the transmitter’s WiFi).

3. Tap the “Live” button.

4. Enter your streaming RTMP URL and code (obtain these from your streaming platform’s instructions).

5. Tap “Go Live” to start streaming.

Note: Please refer to the official website of your desired streaming platform for instructions on how to obtain your live streaming URL and code.

1. Firmware Download:

a. Ensure your mobile device has Internet access via WiFi.

b. Open the Accsoon Go App, select “CineView”.

c. Tap the “Firmware Update” button.

d. The App will automatically search for the latest firmware on the server.

e. If new firmware is available, tap “Download” to download it to your phone.

2. Firmware Update:

a. Once the new firmware is downloaded, connect your mobile device to the CineView HE’s WiFi network (“Accsoon_****”).

b. In the Accsoon Go App (within the Firmware Update section), tap “Next” to begin the update process.

1. Ensure your mobile device’s WiFi can access the Internet before searching for the latest firmware.

2. Make sure the battery level of the CineView HE unit being updated is above 50% before starting the update.

3. Do not interrupt the power supply to the CineView HE during the upgrade process.

4. The CineView HE will reboot automatically once the update is complete.

5. For visual guidance, refer to the “Accsoon Go App Tutorial – Firmware update” video on Accsoon’s official YouTube channel.

Additional Receiver Feature: USB Video Class (UVC) Out via USB-C port.

1. Contact your local Accsoon authorized dealers for after-sales service.

2. If there are no local authorized dealers, you can contact Accsoon customer service via email (support@accsoon.com) or the website (www.accsoon.com) to get support.

3. You will receive detailed solutions from the authorized dealers or Accsoon.

4. Accsoon reserves the right to review the damaged product.

Note: Please keep the proof of purchase and the user manual in a safe place.

1. Please make sure the transmitter and receiver are set to the same group number.

2. Please check that the antennas on both the transmitter and receiver are securely mounted.

1. Check if the HDMI cable from the camera is correctly plugged into the HDMI IN port of the transmitter.

2. Check if the video format and other information are shown on the OLED display interface. If not, check the HDMI cable and verify that the camera’s HDMI port is outputting a video signal.

3. Verify that the HDMI video format output by the camera is compatible with the formats supported by the CineView HE (listed in the specifications).

1. Ensure that all antennas on both the transmitter and receiver are securely mounted.

2. Make sure there are no obstructions, especially metal objects or cables, around the antennas that could cause signal blocking.

3. Try switching to a different transmission channel manually via the transmitter’s menu.

CineView HE broadcasts two WiFi signals (2.4G and 5G). Please confirm that your mobile device is attempting to connect to the correct network, which is named “Accsoon_****”. Ensure you enter the correct password (“12345678” by default).

1. Check if the WiFi connection your mobile device is currently using has proper access to the internet.

2. Check if your mobile device has automatically reconnected to the CineView HE’s own WiFi signal (“Accsoon_****”). If it has, switch your mobile device’s WiFi connection back to a network that provides internet access, and then try searching for the firmware again in the app.