A-NEUVIDEO ANI-RGB1616-A (01) PDF MANUAL

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this equipment:

• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

The matrix series switchers can be divided into the following categories:

• Host Device
• RS-232 Cable
• Power Cable
• CD of testing and application software
• User Manual, Certification and Guarantee Card
• Audio connector

The way to operate the panel switch is like this: “input”+”switch model”+”output”+”enter”

• Input: 9 number on the panel, also can combined two or three numbers together to choose double or triple digital.
• Switch Model: “A”,”AV”,”V”,”VGA” means switching computer & audio/computer/Audio
• Output: 9 number on the panel, also can combined two or three numbers together to choose double or triple digital.

• Input switch to Output: “input”+”V, AV, A, VGA”+”output”+”ENTER”
• One input switch to all output: “input”+“V, AV, A, VGA”+“output 0”+“ENTER”
• Close one output: “input 0”+“V, AV, A, VGA” +”ENTER”
• Close all output: “0”+”V, AV, A, VGA”+“0”+“ENTER”

Before using the serial port to control the device, please confirm the following configuration:

• Baud Rate: 9600bps
• Data bit: 8 bits
• Parity: None
• Stop Bits: 1
• Flow Control: None

Use a straight RS-232 cable. DO NOT USE null modem cable.

Please check when the following problems occur:

• When the peripherals connected to the matrix switcher have a ghost image and the display does not generally have problems. The display may not be correctly tuned or quality wire impedance is mismatched by the signal generating double or multiple reflections. Adjust the display or replace the wire to solve the problem.
• In case of color loss or no signal on an Output, check the connecting port.
• When the AV matrix cannot be controlled by RS-232 (PC Serial port), please check the configuration of the port and the connection of the port.
• Switch with no output image: Check corresponding Input signal (can refer to oscilloscope or multimeter), if there’s no Input signal, check the connecting cable, connector, maybe change to another connector.
• Check corresponding Output signal (refer to oscilloscope or multimeter), if there’s no Output signal, check the connecting cable, connector, maybe change to another connector.
• If power light is Off and no display on the LCD check the connection of power. While you may laugh at this, it does happen.
• If the output image shows interference, the input & output devices may not be grounded.
• If you feel electrostatic spark when pulling, inserting audio or video connectors, it is possible the matrix switcher is not properly grounded. Please ground the device(s) or it will easily damage the equipment and reduce the life.
• If LCD displays, the serial port returns code, but there is no video or audio output: The audio and video connector may be loose. The cable may be short-circuited.
• If the AV matrix cannot be controlled by the front panel push buttons or RS-232, the switcher may be damaged.

1. Run the software.
2. Right click “Matrix Fix” and menu appears like.
3. Click “Add Device”, a dialog appears. Select serial port number, baud rate and address.
4. Click “OK” to connect the device. After receiving device information, the controlling Interface is done.