A-NEUVIDEO ANI-315XLR (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download A-NEUVIDEO ANI-315XLR (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** ANN-315 L Transmitter & Receiver HDMI over CAT5e/6 Extender with IRIRS-232 ANI-315XLT A-NeuVideo.com Frisco, Texas 75036 ANI-315XLR A > NEIJ VIDEO AUDIO / VIDEO MANUFACTURER

****** Page 2 ****** 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. SAFETY INFORMATION To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. Follow all instructions printed on unit chassis for proper operation. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty. Turn power off and disconnect unit from AC current before making connections. Never hold a power switch in the “ON” position. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. The equipment power cord should be unplugged from the outlet when left unused for a long period of time. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. Service Information Equipment should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment. C. The equipment has been exposed to rain. D. The equipment does not appear to operate normally, or exhibits a marked change in performance. E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

****** Page 3 ****** A»NEUVIDEO CONTENTS INTRODUCTION & CONTENTS FEATURES . SPECIFICATIONS OPERATION CONTROLS & FUNCTIONS IR PIN ASSIGNMENT CONNECTION DIAGRAM DEAN CUSTOMER 2 €3 4 5 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. INTRODUCTION The ANI-315XL HDMI Extender over single CAT5e/6 incorporating IR and RS-232 signal transfer, allows for a more efficient system setup and is easy to install. Uncompressed video and audio can be transmitted for distances up to —196 ft (60M) @1080p and —115 ft (35M) @4K and supports High Definition Audio and 3D signals. Designed with HDBaseTT'” technology, for greater flexibility in custom installations with full HDMI and control signal transfer over a single CAT5e/6 cable. This product has a 3 year warranty. PACKAGE CONTENTS Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton: TRANSMITTER PACKAGE • ANI-315XLT HDMI over CAT5e/6 Transmitter w/ IR/RS-232 • IR Blaster (included with Transmitter module only* ) • 3.5mm mini-jack to RS-232 female cable • 5V/2.6A DC PowerAdaptor • Users Guide RECEIVER PACKAGE • ANI-315XLR HDMI over CAT5e/6 Receiver w/ IR/RS-232 • IR Extender (included with Receiver module only* ) • 3.5mm mini-jack to RS-232 male cable • 5V/2.6A DC PowerAdaptor • Users Guide *Both the IR Blaster and IR Extender are NOT included with EACH module. APPLICATIONS • Residential entertainment sharing and control • University lecture hall display and control • Retail sales display and control • Meeting room presentation and control • Commercial advertising display and control SYSTEM REQUIREMENTS HDMI source equipment such as a DVD/Blu-ray player/PC and TV/ monitor/projector with HDMI input and HDMI to CAT5e/6 cables. TABLE OF CONTENTS SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use. We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document. We reserve the right to make improvements to this document and/ or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent. O Copyright 2016. All Rights Reserved. Version 1.2 AUG 2016 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. 1

****** Page 4 ****** A»NEUVIDEO FEATURES • HDMI with 3D, 4K2K support, HDCP and DVI compliant • Complies with the HDBaseT Lite”” class FEATURES & SPECIFICATIONS • Supports HDMI (including HDCP) over a single CAT5e/6 up to 196 ft (60M) • Full HD resolution supports (1080p@60Hz/36bit), 3D and 4K2K for up to —131 ft (40M) and PC resolution supports (VGA to WUXGA) over a CAT5e/6 cable • HDMI input cable length up to —50 ft (15M) with 8bit resolution or -33 feet (10M) with 12bit resolution • HDMI output cable length up to —50 ft (15M) with 8/12bit resolution • Multiple control interfaces such as RS-232 with baud rate up to 115200/sec and IR • Supports HDCP repeater and CEC bypass • Supports High Definition LPCM 7.1CH, Dolby TrueHD, Dolby Digital • Plus and DTS-HD Master Audio transmission • Compact size with stylish design SPECIFICATIONS TRANSMIT TEA • Input: (1) HDMI, (1) RS-232 • Output: (1) RJ45, (1) IR Blaster • Weight: 20z / 56g • Power Consumption: 3W AECEIVEÄ • Input: (1) RJ45, (1) IR Extender • Output: (1) HDMI, (1) RS-232 • Weight: 2.30z / 64g • Power Consumption: 5.5W GENERAL • Video Bandwidth: 300MHz/10.2Gbps • ESD Protection: Human Body Model: • ±8kV (air-gap discharge) • ±4kV (contact discharge) • Power Supply: (2) 5V/2.6A DC (US/EU standards, CE/FCC/UL certified) • Dimensions (WxDxH): 2.1 x 3.3 x .9 In (55x82x22.5mm) • Chassis Material: Plastic • Silkscreen Color: White • Operating Temperature: 320F—1040F (OOC—400C) • Storage Temperature: —40F—1400F (—200C—600C) • Relative Humidity: 20—90 % RH (non-condensing) As product improvements are continuous, specifications are subject to change without notice. 2

****** Page 5 ****** A»NEUVIDEO OPERATION CONTROLS & FUNCTIONS TRANSMITTER FRONT & BACK PANELS IR OUT HDMI IN RS.232 IN DC 5V CAT5e/E OUT O IR OUT/BLASTER: Connects to the supplied IR blaster for IR signal transmission to the source equipment. Place the IR blaster in direct line-of-sight of the equipment to be controlled. O HDMI IN: Connects to the HDMI input source devices such as a DVD player or a Set-top Box with HDMI cable or DVI to HDMI cable. O RS-232 IN: Connects the 35mm mini-jack to D-Sub 9-pin female adaptor cable (included in the package) to a PC or laptop for the transmission of RS-232 commands. Plug the 5V DC power supply into the unit and connect the adaptor to an AC outlet. O CAT5e/6 OUT: Connects to the receiver unit with a single CAT5e/6 cable for transmission of all data signals. RECEIVER FRONT & BACK PANELS DC SV CATSe/6 IN Plug the 5V DC power supply into the unit and connect the adaptor to an AC outlet. O CAT5e/6 IN: Connects to the transmitter unit with a single CAT5e/6 cable for transmission of all data signals. O IR INIExtender: Connects to the supplied IR extender cable for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR extender. O HDMI OUT: Connects to a HDMI equipped TV/monitor for display of the HDMI input source signal. O RS-232 OUT: Connects the 3.5mm mini-jack to D-Sub 9-pin male adaptor cable (included in the package) to a PC or control system with D-Sub 9-pin cable for the transmission of RS-232 commands. 3

****** Page 6 ****** A»NEUVIDEO OPERATION CONTROLS & FUNCTIONS TRANSMITTER & RECEIVER TOP PANELS HDMI to CAT5e/6 with IR/RS-232 LINK TRANSMITTER LINK CAT5e/6 to HDMI with IR/RS-232 RECEIVER O LINK LED: This LED will illuminate blue when the devices are connected with a CAT5e/6 cable. If the data transmission has an error the LED will blink. IA PIN ASSIGNMENT IR Blaster IIR Receiver D-SUB 9-PIN DEFINITIONS PIN DEFINITIONS PIN 3 WC TxD/RxD RxD/TxD NIC GND Power 5V IR Blaster Signal NC O IR Signal Power 5V Ground DEFINITIONS WC N/C N/C NIC

****** Page 7 ****** A»NEUVIDEO CONNECTION DIAGRAM Blu-ray Player IR Blaster Power Supply Power Supply IR Extender 3m 7m 3m 08 CAT5e/6 (60m) HDMI Cable HD Monitor 5 CONNECTION DIAGRAM RS.232 Cable RS.232 Cable 3rd Party Equipment requiring RS232 Control

****** Page 8 ****** A»NEUVIDEO TERMS & CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you. RESTRICTIONS ON USE OF THE PRODUCT It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage. The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVldeo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product. The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only. A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVldeo. The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls. Disclaimers and Limitation of Liability A-NeuVideo may change or modify the Product at any time, from time to time. THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product. TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO. UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FORANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT. END OF DOCUMENT 6


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.