Post questions, comments, reviews or page errors in the comment box below.

Click here to download 3M X55 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** S55/X45/X55 Multimedia Projector Operator’s Guide Thank you for purchasing this projector. ACAUTION >Before using, read the “Product Safety Guide” and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. Aboutthis manual Various symbols are used in this manual. The meanings of these symbols are described below. AWARNING This symbol indicates information that , if ignored, could possibly result in personal injury or even death due to incorrect handling. ACAUTION This symbol indicates information that , if ignored, could result possibly in personal injury or physical damage due to incorrect handling. Q Please refer to the pages written following this symbol. NOTE • The information in this manual is subject to chance without notice. • The manufacture assumes no responsibility for any errors that may appear in this manual. • The reproduction, transmission or use of this document or contents is not permitted without express written authority. Trademark acknowledgment • VGA and XGA are registered trademarks of the International Business Machines Corporation. • Apple and Mac are registered trademarks of the Apple Computer, Inc. • VESA and SVGA are trademarks of the Video Electronics Standard Association. • Windows is a registered trademark of the Microsoft Corporation. • Internet Explorer is a trademark of the Microsoft Corporation. All other trademarks are the property of their respective owners. 1

****** Page 2 ****** Contents Contents About this manual . Contents Projector features Preparations Part names Projector Controls Remote control Setting up Arrangement . Adjusting the projector’s elevator Attaching the base. About the filter cover for bottom-up use . .2 .3 .3 .4 4 5 5 .6 7 8 9 EASY Menu . Aspect, Keystone, Mode, Bright, Contrast, Color, Tint, Sharpness, Whisper, Mirror, Reset, Filter time, Language, Go to advanced menu PICTURE Menu. 24 26 Bright, Contrast, Gamma, Color temp, Color, Tint, Sharpness, Progressive, My memory IMAGE Menu 29 Aspect, Over scan, V. position, H. position, H. phase, H. size, Auto adjust INPUT Menu 31 10 Connecting your devices . .11 Connecting power supply 14 • 15 Remote control Putting batteries 15 Using the remote control . 16 Power onloff …………. 17 Turning on the power. 17 Turning off the power. 17 Operating 18 Adjusting the volume . 18 Temporarily muting the sound 18 Selecting an input signal 18 Searching an input signal 19 Selecting the aspect ratio 19 Adjusting the zoom and focus 19 Using the automatic adjustment feature . 20 Adjusting the position 20 Correcting the keystone distortions 20 Using the magnify feature . Freezing the screen. Temporarily blanking the screen Operating the computer screen. Multifunctional settings …. 23 Using the menu function 2 Color space, Component, Video format, Frame lock, Information SETUP Menu. Keystone, Whisper, Mirror, Volume SCREEN Menu 33 34 Language, Menu position, OSD bright, Blank, Start up, MyScreen, MyScreen lock, Message OPTION Menu. 37 21 21 21 22 23 Search, Auto off, Lamp time, Filter time, Service Maintenance ….. .39 Lamp 39 Air filter 41 Other care . 42 Troubleshooting . 43 Related messages. 43 Regarding the indicator lamps. 45 Phenomena that may easily be mistaken for machine defects 47 Specifications ………… 49 Accessories . ………….51

****** Page 3 ****** Projector features I Preparations Projectorfeatures This projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. It requires just a little space for installation and gets a large image from short distance. O High Brightness Newly developed 165W IJHB (Ultra High Brightness) lamp gives you a higher brightness image on a screen. The image can be still kept as bright and clean enough for use in bright rooms. O Low Noise WHISPER mode is equipped for reducing acoustic noise to realize quieter operation. It is perfect for use in low luminance rooms where low noise is more important than brightness. O Rich Connectivity This projector has a variety of 1/0 ports. It can be easily connected to many signal sources like PC, DVD and so on. The rich connectivity provides you more options to make your presentation impressive. O Compact Body Even with its many features, this projector is extremely compact and slim, which gives you more flexibility and usability to use it where you want. Preparations About contents of package Your projector should come with the items shown below. Contact immediately your dealer if anything is missing. NOTE • Keep the original packing materials for future reshipment. For moving the projector, be sure to use the original packing material. Use special caution for the lens part. Projector Operator’s Guide Remote control (with AA batteries) Product SafetyGuide Filter cover Quick Start Guide bottom-up use Warranty VGA cable Soft case Power cord EUROPE) Base 3

****** Page 4 ****** Part names Partnames Projector Zoom knob (019) Focus ring (Q19) Vent (Q6) Lens (017) Lamp door (Lamp unit is inside.) Control buttons (See the following page.) ports (See below.) AUDIO OUT port (012) AUDIO INI port (012) S-VIDEO port (013) COMPONENT VIDEO ports (013) CB/PB CR/PR VIDEO port (013) AUDIO IN2 port (012) USB port (022) Front-Right side Bottom side Rear-Left side .ÄOi- ports Remote sensor (016) Speaker Elevator button (08) Elevator foot (Q8) Filter cover (041) (Air filter and intake vent are inside.) Power switch (Q17) AC inlet (Q14) Elevator button (08) Elevator foot (Q8) Vent (06) Restart switch (*) (047) RGB INI port (012) RGB IN2 port (012) RGB OUT port (012) CONTROL port (012) Kensington lock slot NOTE (*) About Restart switch: This Projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar and before turning on again, make the projector cool down at least 10 minutes without operating. Only push the Restart switch in these exceptional instances. 4

****** Page 5 ****** Control buttons LAMP indicator (045) TEMP indicator (045) POWER indicator (017) STANDBY/ON button (017) Remote control RGB button (Q18) VIDEO button (018) ASPECT button (019) HOME button (022) MAGNIFY (021) ON button OFF button END button (022) FREEZE button (021) POSITION button (020) Cursor buttons ESC button (Q23) VIDE POSITION 01 -E con MUTE Part names Cursor buttons Place the projector in a stable position horizontally. A fall or a turnover could cause an injury and/or damage to the projector. Then using damaged projector could result in a fire and/or an electric shock. • Don’t place the projector on an unstable, slant or vibrant surface such as a wobbly or inclined stand. • Do not place the projector in the side/front/rear-up position, except care of the air filter. • For the projector installed bottom-up, use the accessory filter cover for bottom- up use. And in the case of a ceiling installation or the like, contact your dealer before installation. > Place the projection in a cool place, and pay attention enough to ventilation. The high temperature of the projector could cause a fire, a burn and/or malfunction to the projector. • Don’t stop up, block and cover the projector’s vents. • Keep a space of 30 cm or more between the sides and other objects such as walls. • Don’t place the projector on a metallic thing or anything weak in heat. • Don’t place the projector on a carpet, cushion or bedding. • Don’t place the projector in direct sunlight or near a hot object such as heater. • Put nothing about lens and vents of the projector. Put nothing on the projector. • Put nothing that is sucked or sticks to the bottom of projector. This projector has some intake vents also on the bottom. not place the projector on the place that gets wet. Damping the projector or inserting liquid in the projector could cause a fire, an electric shock and/or malfunction to the projector. • Don’t place the projector in a bathroom or the outdoors. • Put nothing containing the liquid near the projector. ACAUTION “void a smoky, humid or dusty place. Placing the projector in such place could cause a fire, an electric shock and/or malfunction to the projector. • Don’t place the projector near a humidifier, a smoking space or a kitchen. • Put nothing containing the liquid near the projector. >Adjust the direction of the projector to keep light from directly hitting the projector’s remote sensor. 6

****** Page 7 ****** Setting up Arrangement Refer to the illustrations and tables below to determine the screen size and projection distance. The values shown in the table are calculated for a full size screen (S55: 800×600 pixels, X45/X55: 1024×768 pixels). (a) The screen size (diagonal) (b) Distance from the projector to the screen (c) The height of the screen (±10%) (a) At screen (a) Screen size inch m 16:9 (c) up (a) (c) down b Pro•ection distance m inch c b ht cm inch u min. (35) (47) (59) (72) (84) (96) (108) (120) (144) (181) (242) (303) (363) max. 30 40 50 60 70 80 90 100 120 150 200 250 300 (0.8) (1.0) (1.3) (1.5) (1.8) (2.0) (2.3) (2.5) (3.0) (3.8) (5.1) (6.4) (7.6) 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.1 3.7 4.6 6.1 7.6 9.2 1.1 1.4 1.8 2.2 2.5 2.9 3.3 3.6 4.4 5.5 7.3 9.2 11.0 (42) (56) (71) (85) (100) (114) (129) (143) (172) (216) (288) (361) (433) 5 6 8 9 11 12 14 15 18 23 30 38 46 c -2 -2 -2 -3 -3 -4 -4 -5 -6 -8 -10 -12 Screen hei down 2 (2) (3) (4) (4) (5) (5) (6) (7) (9) (12) (15) (18) Screen hei down o (-2) (-2) (-2) 41 55 69 82 96 110 123 137 165 206 274 343 411 16 (22) (27) (32) (38) (43) (49) (54) (65) (81) (108) (135) (162) At 16:9 screen (a) Screen size inch m b Pro•ection distance m inch ht cm inch u min. 1.0 (38) 1.3 (52) 1.6 (65) 2.0 (78) 2.3 (91) 2.7 (105) 3.0 (118) 3.3 (131) 4.0 (158) 5.0 (197) 6.7 (264) 8.4 (330) 10.1 (396) max. 30 40 50 60 70 80 90 100 120 150 200 250 300 (0.8) (1.0) (1.3) (1.5) (1.8) (2.0) (2.3) (2.5) (3.0) (3.8) (5.1) (6.4) (7.6) 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.8 6.0 8.0 10.0 12.0 (46) (62) (77) (93) (109) (125) (140) (156) (188) (235) (314) (393) (472) 39 51 64 77 90 103 116 129 154 193 257 322 386 15 (20) (25) (30) (35) (41) (46) (51 ) (61 ) (76) (101) (127) (152) 7

****** Page 8 ****** Setting up Adjusting the projector’s elevator AWARNING > Do not adjust the projector’s elevator during use or immediately after use. Handling while the projector is in a high temperature could cause a burn and/or malfunction to the projector. ACAUTION > If you press the elevator button without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to adjust the elevator feet. Except for inclining by the elevator feet adjustment, place the projector horizontally. You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you othewise need to adjust the angle of projection. The adjustment range of the elevator feet is 0 to 9 degrees. 1. 2. 3. 8 No _ I Elevator feet Elevator button After making sure that the projector is cool adequately, press and hold in the elevator buttons while holding the projector. The elevator buttons and the elevator feet are on the both sides. Raise or lower the projector to the desired height and the release the elevator buttons. When you release the elevator buttons, the elevator feet will lock into position. As necessary, you can also finely adjust the height of the projector by twisting the elevator feet by hand.

****** Page 9 ****** Setting up Adjusting the projector’s elevator ACAUTION careful not to pinch your finger on the occasion of the handling of a base. not hold the base, lens or other project part to move the projector. not use the base to suspend the projector. not push or put anything on the both sides of the top of the projector. Base Lever Bottom of the projector Front 1 Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45minutes. 2 After make sure that the projector has cooled adequately, slowly flip over the projector, so that the bottom is facing up. 3 Put the base on the bottom of the projector as shown in the figure. Then slide • it to the front of the projector until it locks into position. To remove it, slide the base to the back of the projector pinching the lever of the base. 4 Slowly turn the projector so that the top is facing up. 9

****** Page 10 ****** Setting up About the filter cover for bottom-up use AWARNING > Do not replace the filter cover during use or immediately after use. While the projector connects with a power supply, or the projector is in a high temperature state, handling could cause an electric shock, a fire, a burn and/or malfunction to the projector.Before handling, make sure the power switch is off and the power cord is not plugged in, then wait at least 45 minutes. When the projector is installed bottom up, please use the accessory filter cover for bottom-up use. It is higher than usual filter cover, to keep the space for intake ventilation. Please change in the following procedure. To remove Filter cover’s claw Filter cover To set Filter cover for bottom-up use Filter cover’s claw 1 After making sure that the projector is cool adequately, slowly turn the projector so that the lens-side is facing up. Please be careful for a projector not to fall. While the projector is placed lens-side up, hold the projector. 2. 3. 4. 10 Please unhook the claw of the filter cover using a minus screwdriver or similar, and remove the filter cover. Replace the filter cover for bottom-up use and snap it back into place. Slowly turn the projector so that the top is facing up.

****** Page 11 ****** Setting up Connecting your devices ACAUTION > Turn off all devices prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector. Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector. > Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector. NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer. • Secure the screws on the connectors and tighten. • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. • For some RGB signal modes, the optional Mac adapter is necessary. • When the image resolution is changed on a computer, depending on an input, automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or LCD monitors to change the resolution. About Plug-and-Play capability Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible. • Please take advantage of this function by connecting the accessory RGB cable to the RGB INI port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted. • Please use the standard drivers in your computer as this projector is a Plug-and-Play monitor. 11

****** Page 12 ****** Setting up Examples of connection with a computer * AUDIO INI is linked to RGB INI. 00 RGB out RGB out RS-232C Audio out USB(A) RS-232C cable Audio out RGB cable Stereo mini audio cable 0 00 0029 USB cable o Stereo mini audio cable Connecting to a monitor (output) RGB in 0) RGB cable Connecting to a speaker with amplifier (output) RGB cable o o o 12 Audio in Stereo mini audio cable

****** Page 13 ****** Examples of connection with a VCR/DVD player Audio out Audio out Video out S-Video out S-Video cable Audio out Audio out Component video out C B/PB O Component video cable Component video out CB/PB O CR/PR O • Component video cable Video cable Stereo mini audio cable o Stereo mini audio cable Stereo mini audio cable 002 Q rqb O Stereo mini audio cable Setting up o 13

****** Page 14 ****** Setting up Connecting power supply AWARNING > Please use extra caution when connecting the power cord as incorrect or faulty connections may result in fire and/or electrical shock. • Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one. • Only plug the power cord into an outlet rated for use with the power cord’s specified voltage range. • Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug. AC inlet 1. 2. 14 Connector of the power cord Connect the connector of the power cord to the AC inlet of the projector. Firmly plug the power cord’s plug into the outlet.

****** Page 15 ****** Remote control Remote control Putting batteries AWARNING >Always handle the batteries with care and use them only as directed. Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment. • Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one. • Make sure the plus and minus terminals are correctly aligned when loading a battery. • Keep a battery away from children and pets. • Do not recharge, short circuit, solder or disassemble a battery. • Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place. • If you observe a leakage of a battery, wipe out the flower and then replace a battery. If the flower adheres your body or clothes, rinse well with water immediately. 1. 2. 3. Remove the battery cover. Slide back and remove the battery cover in the direction of the arrow. Insert the batteries. Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control. Close the battery cover. Replace the battery cover in the direction of the arrow and snap it back into place. 15

****** Page 16 ****** Remote control Using the remote control ACAUTION > Be careful in handling the remote control. • Do not drop or otherwise expose the remote control to physical impact. • Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction. • Remove the batteries from the remote control and store them in a safe place if you won’t be using the remote control for an extended period. • Replace the batteries whenever the remote control starts to malfunction. • When strong lights, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hit the projector’s remote sensor, the remote control may cause to function. Adjust the direction of the projector to keep light from directly hitting the projector’s remote sensor. The remote control works with the projector’s remote sensor. —approx. 3 meters 300 • The range of the remote sensor is 3 meters with a 60- degree range (30 degrees to the left and right of the remote sensor). • Also a remote signal reflected in the screen etc. may be available. If it is difficult to send a remote signal to the sensor directly, please try. • Since the remote control uses infrared light to send signals to the projector (Classl LED), be sure to use the remote control in an area free from obstacles that could block the remote control’s output signal to the projector. 16

****** Page 17 ****** Power onloff Poweron/off AWARNING YWhen the power is on, a strong light is emitted. Do not look into the lens or vents of the projector. NOTE • Turn the power on/off in right order. Please power on the projector before the connected devices. Power off the projector after the connected devices. STANDBY/ON button 75 o o Turning on the power POWER indicator Power switch 1 Make sure that the power cord is firmly and correctly connected to the projector and outlet. 2 Set the power switch to the ON position. The power indicator will light to solid orange. Then wait several seconds because buttons may not function for these several seconds. 3 Press the STANDBY/ON button on the projector or remote control. POWER (Solid orange) POWER (Blinking green) POWER O (Solid green) The projector lamp will light up and the POWER indicator will begin blinking green. When the power is completely on, the indicator will stop blinking light green. To display the picture, select an input signal according to the section “Selecting an input signal” (Q18). Turning off the power 1 Press the STANDBY/ON button on the projector or remote control. The message “Power off?” will appear on the screen for approximately 5 seconds. 2 Press the STANDBY/ON button on the projector or remote control again while the message is visible. The projector lamp will go off, and the POWER indicator will begin blinking orange. Then the POWER indicator will stop blinking and light to solid orange when the lamp cooling is complete. 3 Make sure that the power indicator lights to solid orange, to the OFF position. The POWER indicator will go off. Power off? POWER (Blinking’ orange) POWER (Solid orange) set the power switch 17

****** Page 18 ****** Operating Operati ng Adjusting the volume 1 Press the VOLUME button on the remote control. A dialog will appear on the screen to aid you in adjusting the volume. 2 Use the cursor buttons A/ V to adjust the volume. ö öö Flöö To close the dialog and complete the operation, press the VOLUME button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds. Temporarily muting the sound 1 Press the MUTE button on the remote control. ö öö A dialog will appear on the screen indicating that you have muted the sound. To restore the sound, press the MUTE or VOLUME button. Even if you don’t do anything, the dialog will automatically disappear after a few seconds. Selecting an input signal 1 Press the INPUT button on the projector. Each time you press the button, the projector switches its input port as below. RGB INI RGB IN2 COMPONENT VIDEO -Y S-VIDEO VIDEO 1 Press the RGB button on the remote control to select an input port for RGB signal. Each time you press the button, the projector switches its RGB input port as below. RGB INI e» RGB IN2 When the TURN ON is selected to the item SEARCH of OPTION menu (037), the projector selects the RGB INI port at first. If no input is detected at the RGB INI port, projector will check the RGB IN2 port. 1 Press the VIDEO button on the remote control to select an input port for video signal. Each time you press the button, the projector switches its video input port as below. COMPONENT VIDEO S-VIDEO VIDEO When the TURN ON is selected to the item SEARCH of OPTION menu (Q37), the projector selects the COMPONENT VIDEO port at first. If no input is detected at the COMPONENT VIDEO port, projector will begin to check other ports. 18

****** Page 19 ****** Operating Searching an input signal 1 Press the SEARCH button on the remote control. The projector will begin to check its input ports in order to find any input signals. Then when an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation. RGB INI -Y RGB IN2 COMPONENT VIDEO -Y S-VIDEO VIDEO Selecting an aspect ratio 1 Press the ASPECT button on the remote control. Each time you press the button, the projector switches the mode for aspect ratio in turn. O Ata RGB signal NORMAL -Y -Y 16:9 O At a video signal Ino signal 16:9 SMALL • The NORMAL mode keeps the original aspect ratio of the signal. öö At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT VIDEO input, only 16:9 mode can be selected. • Performing the automatic adjustment initializes the aspect ratio setting Adjusting the zoom and focus 1 Use the zoom knob to adjust the screen size. 2 Use the focus ring to focus the picture. Zoom knob Focus ring 19

****** Page 20 ****** Operating Using the automatic adjustment feature 1 Press the AUTO button on the remote control. O At a RGB signal The vertical position, the horizontal position, the clock phase and horizontal size will be automatically adjusted. ÖöÖ@ Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting. O At a video signal The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO mode is selected to the item VIDEO FORMAT of the INPUT menu (031). For a component video signal, the signal type is identified automatically independently of this function. • The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function correctly with some input. Adjusting the position 1 Press the POSITION button on the remote control. The “POSITION” indication will appear on the screen. 2 Use the cursor buttons to adjust the picture position. When you want to reset the operation, press the RESET button on the remote control during the operation. To complete this operation, press the POSITION button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds. • When this function is performed at a video signal, a certain extra such as a line may appear outside a picture. Correcting the keystone distortions 1 Press the KEYSTONE button on the remote control. A dialog will appear on the screen to aid you in correcting the distortion. 2 Use the cursor buttons A/ V to correct the distortion. ö öö COO To close the dialog and complete this operation, press the KEYSTONE button again. Even if you don’t do anything, the dialog will automatically disappear after a few seconds. • This function may not be work well with some input. The adjustable range for correcting will vary among inputs. 20

****** Page 21 ****** Using the magnify feature 1 Press the ON button of MAGNIFY on the remote control. The “MAGNIFY” indication will appear on the screen (although the indication will disappear after several seconds with no operation.), and the projector will enter the MAGNIFY mode. 2 Use the cursor buttons A/ V to adjust the zoom level. Operating öö To move the zoom area, press the POSITION button in the MAGNIFY mode, then use the cursor buttons A/ Y to move the area. And to finalize the zoom area, press the POSITION button again. To exit the MAGNIFY mode and restore the screen to normal, press the OFF button of MAGNIFY on the remote control. e The projector automatically exits the MAGNIFY mode when the input signal changes, or when an operation of changing the display condition (automatic adjustment, etc.) is executed. • Although in the MAGNIFY mode, the keystone distortion condition may vary, it will be restored when the projector exit the MAGNIFY mode. Freezing the screen 1 Press the FREEZE button on the remote control. The “FREEZE” indication will appear on the screen, and the projector will enter the FREEZE mode. To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again. -a 00 ö öö • The projector automatically exits the FREEZE mode when the input signal changes, or when one of the projector’s buttons or the remote control buttons of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME, MUTE, KEYSTONE, POSITION and MENU is pressed. • If the projector continues projecting a still image for long time, the LCD panel might possibly be printed. Do not leave the projector in FREEZE mode for too long. Temporarily blanking the screen 1 Press the BLANK button on the remote control. The blank screen will be displayed instead of the screen of input signal. Please refer to the item BLANK of section SCREEN menu (034). To remove the blank screen and return to the input signal screen, press the BLANK button again. • The projector automatically returns to the input signal screen when the input signal changes, or when one of the projector’s buttons or the remote control buttons are pressed. 21

****** Page 22 ****** Operating Operating the computer screen ACAUTION >Mistaken use of the mouse/keyboard control could damage your equipment. • While using this function, please connect only with a computer. • Before connecting, read the manuals of the computer you will connect. NOTE • It may not be possible to control notebook PC, and other computers with built-in pointing device (e.g. track ball), using this remote control. In this case, before connecting go into BIOS (system setup) and select external mouse, and disable the pointing device. In addition, the mouse may not function if the computer does not have the needed utility program. See your computer’s hardware manual for details. • The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s configurations and mouse drivers. • The USB control can be used only for the functions listed below. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally). • This function is not available while the lamp is warming up (the POWER indicator flashes green), and while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen. USB mouse and keyboard control 1 Connect the projector’s USB port to the computer via the mouse cable. Available function Move ointer Left click with mouse Right click with mouse Press ke board’s HOME ke Press keyboard’s END key Press keyboard’s PAGE UP key Press ke board*s PAGE DOWN ke Press ke boardfs ESC ke 22 Remote control operation Use A, V, < , buttons Press ENTER button Press RESET button Press HOME button Press END button Press PAGE UP button Press PAGE DOWN button Press ESC button ****** Page 23 ****** Multifunctional settings Multifunctional, settings Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION and EASY MENU. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. 01 -z MENU button O ursor buttons ENTER button RESET button 1 Press the MENU button on the remote control or one of the cursor buttons on the projector. The advanced MENU or EASY MENU will appear. 2 Use the cursor buttons A/ V to select a menu. O At the EASY MENU If you want to change it to the advanced MENU, select the "Go to Advanced Menu" O At the advanced MENU Select a menu of PICTURE, IMAGE, INPUT, SETUP, SCREEN or OPTION If you want to change it to the EASY MENU, select the EASY MENU. 3 Then press the cursor button on the projector or remote control, or the ENTER button on the remote control to progress. The display of the selected menu will be active. 4 Use the cursor buttons A/ V to select an item to operate. ööö ö öö GWUA CFAULT EASYMENU TU*NOFF SAVE 1 Advanced MENU EASY MENU KEYSTONE MODE BRIGHT CONTRAST COLOR SHRPNESS W"-IISPER MIRROR RESET FILTER TYE NORMAL NORMAL NORMAL LANGUAGE @ ENGLISH GO TO Advance Menu… EASY MENU Then press the cursor button on the projector or remote control, or the ENTER button on the remote control to progress. The operation menu of the selected item will appear. 5 Use the cursor buttonsA/V to operate the item. When you want to reset the operation, press the RESET button on the remote control during the operation. Note that items whose functions are performed simultaneously with operation (ex. LANGUAGE, H PHASE etc.) aren't reset. When you want to return to the previous display, press the cursor button The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes. “About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws. For lamp recycling, go to lamprecycle.org. (in the US) For product disposal, contact your local government agency or eiae.org (in the US) or wMw.epsc.ca (in Canada). For more information, call your dealer. Disconnect the plug from the power outlet • If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself. • If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth. • Before replacing the lamp, turn the projector off and unplug the power cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp. • Never unscrew except the appointed (marked by an arrow) screws. • Do not open the lamp door while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken. • Do not use the projector with the lamp door removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury. • Use only the lamp of the specified type. • If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative. • Handle with care: jolting or scratching could cause the lamp bulb to burst during use. • If the indicators or a message prompts you to replace the lamp (see the section “Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage. 39

****** Page 40 ****** Maintenance Lamp (continued) When the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. 1 Turn the projector off, and unplug the power cord. Allow the lamp to cool for at least 45 minutes. 2 To prepare a new lamp, contact your dealer and tell the lamp type number 78-6969-9790-3. If the projector is mounted on the ceiling. or if the lamp has broken. also ask the dealer to replace the lamp. In the case of replacement by yourself, 3 After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing up. 4 Unscrew the screw of the lamp door, and remove the lamp door. 5 Loosen the 2 screws (marked by arrow) of the lamp, and slowly pick up the lamp by the handles. 6 Insert the new lamp, and retighten firmly two screws that are loosened in the previous process to lock it in place. 7 Interlocking the 2 tabs of the lamp door to the projector, position the lamp door on the projector. Then tighten the screw of the lamp door. 8 Slowly turn the projector so that the top is facing up. 9 Turn the projector on, and reset the lamp time using the LAMP TIME function of OPTION menu (Q37). Lamp door Screw Screws marked by arrow Tabs Screw NOTE • When the lamp has been replaced after the message of “THE POWER WILL TURN OFF AFTER Ohr.” is displayed, complete the following operation within 10 minutes of switching power on. • Incorrectly resetting of the lamp timer (resetting without replacement, or neglect of resetting after replacement) will result in incorrect message functions. 40

****** Page 41 ****** Maintenance Air filter AWARNING > Before caring, make sure the power switch is off and the power cable is not plugged in, then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. > Use only the air filter of the specified type. Do not use the projector with the air filter and filter cover removed. >Avoid wetting the projector or inserting liquids in the projector. It could result in a fire, an electric shock, and and/or malfunction to the projector. ACAUTION >Please replace the air filter when it is damaged or too soiled, and also when you replace the lamp. When the indicators or a message prompts you to clean the air filter, clean the air filter as soon as possible. If the air filter becomes clogged by dust or the like, internal temperatures rise and the power may be automatically turned off for malfunction prevention. 1 Turn the projector off, and unplug the power cord. Allow the projector to cool for at least 45 minutes. And prepare a vacuum cleaner. 2 After making sure that the projector is cool adequately, slowly turn the projector so that the lens-side is facing up. Please be careful for a projector not to fall. While the projector is placed lens-side up, hold the projector. 3 Unhook the claw of the filter cover using a minus screwdriver or similar, and remove the filter cover. 4 Holding the air filter’s knob, pull the air filter off. 5 Apply a vacuum cleaner to the vent of the projector for the air filter. And then slowly turn the projector bottom up. 6 Apply a vacuum cleaner to the air filter and filter cover. Please replace the air filter when it is damaged or too soiled. To prepare a new air filter, contact your dealer and tell the air Filter cover Filter cover’s claw Air filter’s knob Air filter filter type number = 78-8118-9376-3. An air filter of specified type will come even with the replacement lamp for this projector. 7 Position the cleaned air filter or a new air filter into place, and push the points of ‘PUSH” word with claws to fix the air filter. 8 Replace the filter cover and snap it back into place. 9 Slowly turn the projector so that the top is facing up. 10 Turn the projector on, and reset the filter time using the FILTER TIME function of OPTION menu (038). NOTE • Incorrectly resetting of the filter timer (resetting without replacement, or neglect of resetting after replacement) will result in incorrect message functions. 41

****** Page 42 ****** Maintenance Other care AWARNING > Before caring, make sure the power switch is off and the power cable is not plugged in, and then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause a burn and/or malfunction to the projector. > Never try to care for the inside of the projector personally. Doing is so dangerous. >Avoid wetting the projector or inserting liquids in the projector. It could result in a fire, an electric shock, and and/or malfunction to the projector. • Don’t put a container containing water, cleaner or chemicals near the projector. • Don’t use aerosols or sprays. ACAUTION >Please take right care of the projector according to the following. Incorrect care could cause not only an injury but adverse influence such as discoloration, peeling paint, etc. • Do not use cleaner or chemicals other than those listed below. • Do not polish or wipe with hard objects. Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every 2 years. Caring for the lens If the lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the lens, being cautious of the handling. 1 Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently. 2 After making sure that the projector is cool adequately, lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand. Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration, peeling paint, etc. 1 Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently. 2 After making sure that the projector is cool adequately, lightly wipe with gauze or a soft cloth. If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth. 42

****** Page 43 ****** Troubleshooting Troubleshooting Related messages When the unit’s power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on. Messa e CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. -k CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. THE POWER WILL TURN OFF AFTER ** hr. CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. THE POWER WILL TURN OFF AFTER O hr. NO INPUT IS DETECTED ON *** SYNC IS OUT OF RANGE Hz CHECK THE AIR FLOW Descri tion The time the lamp timer has counted is approaching 2000 hours. Preparation of a new lamp, and an early lamp change is recommended. After you have change the lamp, please be sure to reset the lamp timer (Q37). The time the lamp timer has counted is approaching 2000 hours, so a lamp change within ** hours is recommended. When lamp usage reaches 2000 hours, the power will automatically be turned off. Please change the lamp by referring to the section “Lamp”. After you have changed the lamp, please be sure to reset the lamp timer (037). As the time the lamp timer has counted has reached 2000 hours, the power will soon be automatically turned off. Please immediately turn the power off, and change the lamp by referring to the section “Lamp”. After changing the lamp, please be sure to reset the lamp timer (Q37). There is no input signal. Please confirm the signal input connection, and the status of the signal source. The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please confirm the specs for this unit or the signal source specs. The internal portion temperature is rising. Please turn the power OFF, and allow the unit to cool down at least 20 minutes. After having confirmed the following itemst please turn the power ON again. • Is there blockage of the air passage aperture? • Is the air filter dirty? • Does the peripheral temperature exceed 350C? • If the same indication is displayed after the treatment, please set the HIGH at the FAN SPEED of the item SERVICE of the OPTION menu. 43

****** Page 44 ****** Troubleshooting Related messages (continued) Messa e CLEAN THE AIR FILTER POWER OFF FIRST, THEN CLEAN THE AIR FILTER. AFTER CLEANING THE AIR FILTER, RESET THE FILTER TIMER. Descri tion A note of precaution when cleaning the air filter. Please immediately turn the power OFF, and clean or change the air filter by referring to the “Air Filter” section of this manual. After you have cleaned or changed the air filter, please be sure to reset the filter timer (038). NOTE •A lamp has a finite product life. Lamps are characterized by the fact that, after long hours of usage, a lamp will no longer light up, or the lamp will break or burst, etc. This projector is equipped with an automatic shut-down function, such that the power will automatically be turned off when lamp usage time has reached 2000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this projector. 44

****** Page 45 ****** Troubleshooting Regarding the indicator lamps Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company. POWER LAMP TEMP indicator indicator indicator Lighting In Orange Blinking In Green Lighting In Green Blinking In Orange Blinking In Red Blinking In Red Lighting In Red Blinking In Red Lighting In Red Turned off Turned off Turned off Turned off (discre- tionary) Lighting In Red Blinking In Red Turned off Turned off Turned off Turned off (discre- tionary) Description The projector is in a standby state. Please refer to the section “Power On/Off. The projector is warming up. Please wait. The projector is in an on state. Ordinary operations may be performed. The projector is cooling down. Please wait. The projector is cooling down. A certain error has been detected. Please wait until the POWER indicator finishes blink, and then perform the proper response measure using the item descriptions below as reference. The lamp does not light, and there is a possibility that interior portion has become heated. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of Turned the following items, and then turn the power on again. off • Is there blockage of the air passage aperture? • Is the air filter dirty? • Does the peripheral temperature exceed 350C? If the same indication is displayed after the treatment, please change the lamp by referring to the section “Lamp”. The lamp door has not been properly fixed (attached). Please turn the power off, and allow the unit to cool down at least 45 minutes. After the projector has Turned sufficiently cooled down, please make confirmation of off the attachment state of the lamp After performing any needed maintenance, turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company. 45

****** Page 46 ****** Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP indicator indicator indicator Blinking In Red Lighting In Red Blinking In Red Lighting In Red Lighting In Green Lighting In Green Turned off Turned off Blinking In Red Lighting In Red Alternative blinking in Red Simultaneous blinking in Red Description The cooling fan is not operating. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation that no foreign matter has become caught in the fan, etc., and then turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company. There is a possibility that the interior portion has become heated. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again. • Is there blockage of the air passage aperture? • Is the air filter dirty? • Does the peripheral temperature exceed 350C? If the same indication is displayed after the treatment, please set the HIGH at the FAN SPEED of the item SERVICE of the OPTION menu. There is a possibility that the interior portion has become overcooled. Please use the unit within the usage temperature parameters (50C to 350C). After the treatment, resent the power to ON. It is time to clean the air filter. Please immediately turn the power OFF, and clean or change the air filter by referring to the section “Air Filter”. After cleaning or changed the air filter, please be sure to reset the filter timer. After the treatment, resent the power to ON. NOTE • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “O” (OFF) side of the power switch, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp door, and then turn the power on again. 46

****** Page 47 ****** Troubleshooting Phenomena that may easily be mistaken for machine defects AWARNING > Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company. 1 Before requesting repair, please check in accordance with the following chart. This operation sometimes resolves your problem. If the situation cannot be corrected, 2 The projector’s microprocessor may need to be reset. Please push the Restart switch by using a cocktail stick or similar and the projector will restart. 3 Some setting may be wrong. Please use the FACTORY RESET function of SERVICE menu in the OPTION menu (038) to reset all settings to factory default. Then, if the problem is not removed after maintenance, please contact your dealer or service company. Phenomenon Cases not involving a machine defect The electrical power cord is not plugged in. Correctly connect the power cord. The power switch is not set to the on position. Set the power switch to [ I ] (On). The main power source has been interrupted during operation such as by a power outage (blackout), etc. Power does not Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled come on. down, please turn the power on again. Either there is no lamp and/or lamp door, or either of these has not been properly fixed. Please turn the power off, and allow the unit to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp door, and then turn the power on again. Reference age 14 17 17 39, 40 47

****** Page 48 ****** Troubleshooting Phenomena that may easily be mistaken for machine defects (continued) Phenomenon No pictures are displayed. Colors have a faded- out appearance, or Color tone is poor. Pictures appear dark. Pictures appear blurry. Cases not involving a machine defect The signal cables are not correctly connected. Correctly connect the connection cables. The brightness is adjusted to an extremely low level. Adjust the BRIGHT to a higher level using the menu function or the remote control. The computer cannot detect the projector as a plug and play monitor. Make sure that the computer’s can detect a plug and play monitor using other plug and play monitor. Color settings are not correctly adjusted. Perform picture adjustments by changing the COLOR TEMPT COLOR, TINT and/or COLOR SPACE settings, using the menu functions. COLOR SPACE setting is not suitable. Change the COLOR SPACE setting to AUTO, RGB, SMPTE240 , REC709 or REC601. The brightness and/or contrast are adjusted to an extremely low level. Adjust the BRIGHT and/or CONTRAST settings to a higher level using the menu function. The WHISPER function is working. Select the NORMAL to the item WHISPER in the SETUP menu. The lamp is approaching the end of its product lifetime. Replace the lamp. Either the focus and/or horizontal phase settings are not properly. Adjust the focus using the focus ring, and/or H PHASE using the menu function. The lens is dirty or misty. Clean the lens by referring to the section “Caring for the lens”. Reference page 11 24, 26 11 24, 26, 31 31 25, 26 25, 33 39, 40 19, 29 42 NOTE •Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect. 48

****** Page 49 ****** Specifications SpeCifications NOTE • This specifications are subject to change without notice. Item Product name Liquid Crystal panel Lens Lamp Panel size Drive system Pixels Power Supply Power Consumption Temperature range Size Weight (mass) Ports Specification Liquid crystal projector 1.8 cm (0.7 type) TFT active matrix S55: 480,000 pixels (800 horizontal x 600 vertical) X45/X55: 786,432 pixels (1024 horizontal x 768 vertical) Zoom lens F=1.7 1.9 f=21.8 26.2 mm 165W UHB ACI 00-120V/2.7A, AC220-240V/1.5A 240W 5 350C (Operating) 308 (W) x 86 (H) x 252 (D) mm (Not including protruding parts) • Please refer to the following figure. 2.6 kg RGB input: RGB INI D-sub 15pin mini xl RGB IN2 D-sub 15pin mini xl RGB output: RGB OUT D-sub 15pin mini xl Communication port: Video input: COMPONENT VIDEO CONTROL USB. . D-sub 9pin xl USB(B) xl CB/PB. CR/PR S-Video . Video . Audio input: AUDIO INI AUDIO IN2 . Audio output: AUDIO OUT RCA xl RCAx 1 RCAx 1 1 1 Stereo mini xl Stereo mini xl Stereo mini xl 49

****** Page 50 ****** Specifications Specifications (continued) 50 219 89 [unit: mm]

****** Page 51 ****** Accessories Accessories Accessories Part Number UHB lamp, 165W. Air Filter Power cord (US) .. Power cord (UK) Power cord (Europe) . VGA cable Remote control Soft case . Base Filter cover bottom-up use….. Not included with Basic Packet Ceiling mount Adjustble height suspension…. Shipping case. RCA Video cable S-Video cable RCA component cable.. RS-232C control cable Stereo mini-cable . UHB cable Mac adapter . Soft rolling luggage case. Soft side case with shoulder strup. Ultra value warranty S55(US only) … Ultra value warranty X45(US only) Ultra value warranty X55(US only). Deluxe Mouse Emulation Kit . How to Order 78-6969-9790-3 78-8118-9376-3 78-8118-8102-4 78-8118-8101-6 78-8118-8103-2 78-8118-8708-8 78-8118-9185-8 78-8118-9194-0 78-8118-9378-9 78-8118-9377-1 Part Number 78-6969-9694-7 78-6969-9698-8 78-6969-9717-6 78-8118-8482-0 78-8118-3238-1 78-8118-8843-3 78-8118-91924 78-8118-8846-6 78-8118-9057-9 78-8118-3308-2 78-6969-9716-8 78-6969-9715-0 78-6969-9787-9 78-6969-9788-7 78-6969-9790-3 78-6969-9233-4 Please order these parts through your dealer, or contact 3M Customer Service at the following number . In U.S. or Canada : 1-800-328-1371 In other locations, contact your local 3M sales office. 51

****** Page 52 ****** Intended Use Before operating this machine, please read this entire manual thoroughly. The 3M TM Multimedia Projectors are designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal voltages. The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector peripheral equipment and/or create a unsafe operating condition. 3M Multimedia projectors and Wall Display Systems are designed to operate in a normal office environment. • 16′ to 290C (600 to 850 F) • IO- 80 %RH (without condensation) • O- 1828 m feet) above sea level The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the projector. Use of this product in adverse conditions will void the product warranty- Let us help you make the most of your next presentation. We offereverything from presentation supplies to tips for better meetings. And we’re the only transparency manufacturer that offers a recycling program for your transparencies. For late-breaking news, handy reference and free product samples, call toll-free in continental United States and Canada, 24 hours a day, or visit our Internet Website, 800-328-1371 3M Austin Center Building A145-+U)1 6801 River Place Blvd. Austin, TX (DN00741 – 3M Canada P.O. Box 5757 London, Ontario N6A 4T1 3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 070(1) Mexico 3m.com/meetings e-mail: meetings@mmm.com 3M Europe Boulevard de IOise 95(X.h Cerge Pontoise Cedex France 0 3M 2004 78-6970-9389-2 Rev. A


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

3M X55 (01) PDF MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.