Post questions, comments, reviews or page errors in the comment box below.

Click here to download 3M SCP740 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** Super Close Projection System SCP715/SCP740/SCP717 Operator’s Guide Important Note Before using this product, please read the “Product Safety Guide” and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference. 3m.com/meetings Super Close Projection System Operator’s Guide 0 3M 2008. All Rights Reserved 78-6971-1396-3

****** Page 2 ****** Contact 3M In the event of missing and/or damaged equipment, or technical questions, the following information can help in the completion of the installation. Customer Service – 1-800-328-1371 (US) SCP 700 Series Warranty Statements Limited Warranty • The 3M SCP700 Series projector (the “3M Product”) is warranted is warranted to be free from defects in material or manufacture for a period of three (3) years from the date of purchase or 4,000 hours of usage, whichever occurs first. e All other accessories of the 3M Product (those in the applicable modular configura- tions), excluding the projector lamps, but including the wall mounts, ceiling mounts, digital annotation sensors, and input/output devices are warranted to be free from de- fects in material or manufacture for a period of one (1) year from the date of purchase. • The lamp component of the 3M Product is warranted to be free from defects in mate- rial and manufacture for a period of for a period of ninety (90) days after the date of purchase of the 3M Product or 180 hours of lamp usage, whichever occurs first. This warranty is for parts only and in the case of an approved warranty claim for a lamp, your exclusive remedy will be for a replacement product shipped to your location. e Optional product upgrades and/or accessories that are not sold as part of any modular configuration are subject to individual warranties. THE WARRANTIES STATED ABOVE ARE EXCLUSIVE AND ARE MADE IN PLACE OF ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE, OR ANY INDUSTRY PRACTICE OR CUSTOM OR TRADE USAGE. In the event the 3M Product fails to conform to the above stated warranties within the applicable warranty period, your exclusive remedy shall be, at 3M*s option, to replace or repair the 3M Product or to refund the purchase price of the 3M Product. All replaced parts or products become property of 3M. If the product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the 3M Product is replaced, 3M will replace the 3M Product with the same or equivalent model and with a new or refurbished 3M Product. In the case of an approved warranty claim, the replacement 3M Product will carry only the re- maining term of the original 3M Product’s warranty period as stated above.. For warranty service, you must provide proof of the date of the orginal purchase else the manufacturing code date will be used to establish the start date of the warranty. The following are exclu- sions to the above listed warranty: 0 3M 2008. All Rights Resewed.

****** Page 3 ****** 3MTM Super Close Projection System Table of Contents a. This warranty does not cover 3M Product that is modified or damaged through im- proper storage, misuse, abuse, accident, vandalism, improper installation, neglect, improper shipping, damage caused by acts of war, disasters such as fire, flood, and lightning, improper electrical current, software problems, interaction with non-3M prod- ucts, or service other than by an 3M Authorized Service Provider, neglect or mishan- dling by any person. Normal wear and tear is not covered under warranty. b. 3M Product is designed to operate in the typical indoor environment. This warranty does not cover 3M Product used outside of the following circumstances: 0 100V-240V AC, 50/60 Hz 0 160 to 290 C (600 to 850 F) 0 10-80% RH (without condensation) 0 0-1828m (0-6000 feet) above sea level c. The Air Intake and Exhaust Vent must be clear of obstructions, including any potential blockage or obstructions caused from a ceiling or other mount. Inadequate air ventila- tion will cause the 3M Product to malfunction or will cause damage to the 3M Product which will void the warranty. d. This warranty does not cover any additional costs including, but not limited to, those associated with removal, cleaning or installation of the 3M Product, adjustments, (mechanical or electronic) made to the 3M Product or replacing customer replaceable parts like lamps and air filters. e. This warranty covers only normal use of the product. 24-hour-per-day or other exces- Sive continual use causes strain and is not considered normal use. f. This warranty does not cover consumables (e.g., fuses), other than lamps and only as set forth below. g. This warranty is not transferable. h. 3M is not responsible for warranty service should the 3M label or logo or the rating label or serial number be removed unless othenNise stated in writing for the purposed of private labeling for partnership requirements. i. This warranty does not cover postage, insurance, or shipping costs incurred in pre- senting your 3M Product for warranty service. Said costs are the customer’s respon- sibility. If a claimed defect cannot be identified or reproduced in service, the customer may be held responsible for cost incurred. Should your warranty upgrade include a “change out” service and the claimed defect cannot be identified or reproduced by the technician, the customer will be responsible for call out costs. FAILURE TO FOLLOW THE INSTRUCTIONS CONTAINED IN THE APPROPRIATE 3M PRODUCT MANUAL OR TO USE THE 3M PRODUCT IN ACCORDANCE WITH 3M’s IN- TENDED USE STATEMENT, WILL VOID ALL WARRANTIES AND LIMITED REMEDIES. 0 3M 2008. All Rights Resewed. 111

****** Page 4 ****** Table of Contents 3MTM Super Close Projection System EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL, 3M SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUEN- TIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, REVENUE OR BUSINESS) RESULTING FROM, OR IN ANY WAY RELATED TO PERFORMANCE, USE OR INABILITY TO USE ANY OF THE 3M PRODUCT. This limitation applies regard- less of the legal theory upon which damages are sought. For warranty support, please call or write your local 3M office or a 3M Authorized Service Provider to obtain an RMA # (Return Material Authorization Number) before returning the product. If you are inside the Continental United States of America, please contact 3M Customer Service at 800-328-1371 or email meetings@mmm.com. What 3M Will Do To Correct Problems: e If your 3M Product requires service, 3M will ask you to bring or send the 3M Product, securely packaged in its original container or equivalent, along with proof of the date of original purchase, to your 3M Service Dealer or 3M Service Center. • 3M will, at its option, repair or replace the defective unit without charge for parts or labor. Return of the 3M Product will be at 3M’s expense. • When warranty service involves the exchange of the 3M Product or of a part, the item replaced becomes 3M property. e The exchanged 3M Product or part may be new or previously refurbished to the 3M standard of quality, and at 3M’s option, the replacement may be another model of like kind and quality. • 3M’s liability for replacement of the warranted 3M Product or part will not exceed the original retail selling price of the 3M Product. Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty. However, each replacement lamp carries the limited 90-day warranty stated above. 0 3M 2008. All Rights Resewed.

****** Page 5 ****** 3MTM Super Close Projection System The 3M logo, and 3M are trademarks of the 3M Company. Important Notice Table of Contents All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product or implementation, you must evaluate them and de- termine if they are suitable for your intended application or situation. You assume all risks and liability associated with such use or implementation. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. All rights reserved. No part of this book covered by the copyrights hereon may be repro- duced or copied in any form or by any means-graphic, electronic, or mechanical, including photocopying, taping or information storage and retrieval systems-without written permis- Sion of 3M Projection Systems Department. 0 3M 2008. All Rights Resewed.

****** Page 6 ****** 3MTM Super Close Projection System Important Note …………………………………………………………………………………………6 Product Features .. … … … … … … … … … … … … … … … … … … … … 7 Package Overview……………………………………………………………………………………8 Product Overview …. … … … … … … … … … … … … … … … … … … … .9 Remote Control with Mouse Function……………………………………………………… Powering On the Projector………………………………………………………………………………. 15 ….. ….. .. 19 .. …23 ……26 Table of Contents . Usage Notice.. Precautions. Introduction. Main Control Panel Connection Ports Installation … Connecting the Projector. Connect the Computer/Notebook . Connect the Video ….. ….. ….. ….. …………… . Powering On/Off the Powering Off the projector . . LED Indicator ….. ….. ….. …………………………………………………………………… Adjusting the Projected Image… Adjusting the Projector Image Height Adjusting the Projector Focus ….. ….. …. 3M Super Close Projection System SCP715/SCP717 Adjusting Projected Image Table of Contents 1 2 7 ..9 ….. .. 10 11 12 13 .13 . . .. ……………………….13 ….14 .15 . 16 ….. ….. ….. … 16 17 ….. .. 18 Size . 18 3M Super Close Projection System SCP740 Adjusting Projected Image Size User Controls Control Panel & Remote Control On-Screen Display Menus.. How to Operate Menu Tree-1/2………………………………………………………………………………………………..24 Menu Tree-2/2………………………………………………………………………………………………..25 Information . Management-1/3…………………………………………………………………………………………….27 Management-2/3…………………………………………………………………………………………….29 Management-3/3……………………………………….. Image-1/2……………………………………………………………. . .. .. ……………………………32 LAN ….. ….. ….. ……………………….. Security. Troubleshooting. … … … … … … …. … … … … … … … … … … … … … …. Replacing the Lamp.. Compatibility Modes ….. ….. ….. ……………………. RS232 Protocol Function List…. Regulation & Safety notices 0 3M 2008. All Rights Resewed. 20 .20 ..23 .31 ..35 ..37 43 .43 47 .48 49 52 1

****** Page 7 ****** Usage Notice 2 3MTM Super Close Projection System Precautions Follow all warnings, precautions and maintenance as recommended in this user’s guide to maximize the life of your unit. AWARNING e Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes. • To reduce the risk of injury to the eyes, do not look directly into the laser light on the remote control and do not point the laser light into anyone eyes. This remote control is equipped with a Class II laser that emits radiation. • To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. • Please do not open or disassemble the product as this may cause electric shock. e When changing the lamp, please allow unit to cool down, and fol- low all changing instructions. • Position the power cord and data cable so that they can not be tripped over. • Do not remove any screws other than those specified in the lamp replacement instructions. • Disconnect power cord when the projector is not in use, during lamp replacement and while cleaning. • Switch power “OFF” and disconnect the plug from electrical outlet before replacing the lamp. Grasp plug and pull to disconnect. e Do not attempt to service the projector; other than the lamp car- tridge there are no user serviceable parts inside the projector. 0 3M 2008. All Rights Resewed.

****** Page 8 ****** 3MTM Super Close Projection System AWARNING Usage Notice • Do not attempt to service the projector other than performing routine lamp replacement. Service should only be performed by a 3M authorized service provider Aside from the projection lamp assembly, there are no serviceable parts inside the unit. • Contact a 3M authorized service provider for service. e Do not modify this projector. • Do not allow water or other liquids to enter the projector. • Do not operate this projector in wet environments or outdoors. e Do not use this projector around unsupervised children • Replace power cord if damaged. e Contact a 3M authorized service provider if the projector be- comes damaged. • Connect this projector into a grounded outlet. e Use a grounded extension cord with a rating at least equal to that of the projector. • Use only the 3M brand wall mounting hardware kit if wall mount- ing is desired. – Installation of 3M wall kit must only be performed by qualified personnel. – Adhere strictly to the proper installation procedure as outlined in the installation instructions when installing the 3M wall kit. e Always operate the unit on a flat, sturdy, and horizontal surface. • Before operating, please read owner’s manual. Do not remove screws except lamp cover screws. Do not block venting open- ings. 0 3M 2008. All Rights Resewed. 3

****** Page 9 ****** Usage Notice 4 3MTM Super Close Projection System AWARNING • Lamp replacement caution. Before removing the screws, discon- nect the power cable. Hot surface inside. Allow 1 hour to cool before replacing the lamp. Handle with care. Risk of explosion. See Owner’s Manual. • Unplug the projector from the electrical outlet and allow the lamp to cool for 60 minutes before replacing the lamp. e Wait at least 30 minutes for the lamp assembly to cool before replacing. • Always handle the fragile lamp module with care. e In the event of a lamp rupture, call a 3M authorized service pro- vider for repair. Ruptured lamp is not user serviceable. • Ventilate the area where the lamp rupture occurred. The lamp operates at high pressure and temperature. • Replace the lamp module when the lamp replacement message appears. e Never replace the lamp module with a previously used lamp module. • Hg: Lamp contains mercury. Don’t throw in trash. Dispose ac- cording to local, state, or federal laws. See lamprecycle.org or call 1-800-328-1371. • Wash your hands thoroughly if contact with ruptured lamp debris has taken place. e Ventilate the area where the lamp rupture occurs. The lamp oper- ates at high temperature. 0 3M 2008. All Rights Resewed.

****** Page 10 ****** 3MTM Super Close Projection System AWARNING • Use only battery type AA. Usage Notice Orient the batteries plus (+) and (-) terminals of the batteries ac- cording to the markings found on the remote control. – Do not leave the battery in the remote for an extended period of time. Do not heat, disassemble, short, recharge, or expose to fire or high temperature. – Do not carry batteries loose in your pocket or purse. – Avoid eye and skin contact in the event that battery would leak. – Do not mix used and new batteries. • Dispose of exhausted batteries in accordance with applicable federal, state and local regulations. • Avoid looking directly into projector lens while the lamp is on. • Keep the battery and battery cover away from children and pets. e Changes or modifications not expressly approved by the manu- facturer could void the user’s authority, which is granted by the Federal Communications Commission to operate this computer. Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don’t: Block the slots and openings on the unit provided for ventilation. Use abrasive cleaners, waxes or solvents to clean the unit. Use under the following conditions: – In extremely hot, cold or humid environments. – In areas susceptible to excessive dust and dirt. Near any appliance that generates a strong magnetic field. – In direct sunlight. 0 3M 2008. All Rights Resewed. 5

****** Page 11 ****** Usage Notice 6 3MTM Super Close Projection System Important Note 1 . This product will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages. 2. Reset the “Lamp Counter Reset” function from the On Screen Display “Management” menu after replacing the lamp module (refer to page 28). 3. When switching the projector off, please allow the projector to complete its cooling cycle before disconnecting the power. 4. Turn on the projector first and then the signal sources. 5. When the lamp reaches the end of its life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp”. (see page 47) 0 3M 2008. All Rights Resewed.

****** Page 12 ****** 3MTM Super Close Projection System Product Features Introduction 3M super Close Projection System SCP715/SCP717 are XGA single chip O. 7″ DLP projectors and 3M Super Close Projection System SCP740 is a WXGA single chip DLP@projector. Outstanding features include: SCP715/SCP717 – True XGA, 1024 x 768 addressable pixels SCP740 True WXGA, 1280 x 800 addressable pixels Texas Instruments Single chip DLP@ Technology NTSC/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and HDTV compatible (480i/p, 576i/p, 720p, 1080i/p) Multi-Auto functions: Auto detection, Automatic saving of user adjustments Full function IR remote control with mouse function User friendly multilingual on screen menu Advanced digital keystone correction and high quality full screen image re-scaling User friendly control panel Two built-in speakers with 2 Watt amplifier Multiple for Audio inputs Computer Compatibility: UXGA, SXGA+, SXGA compression and SVGA, VGA re-sizing Mac compatible DVI support (HDCP compliant) Support Network function (LAN/RS232) 0 3M 2008. All Rights Resewed. 7

****** Page 13 ****** Introduction 8 3MTM Super Close Projection System Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if anything is missing. Projector EUR AC Power Cord USB Cable Documents . Operator’s Guide Quick Start Card Product Safety Guide WEEE card US AC Power Cord VGA Cable e ee ooo ooo Wireless Remote Controller UKAC Power Cord 3.5mm Audio Cable 2 x AA Batteries 0 3M 2008. All Rights Resewed.

****** Page 14 ****** 3MTM Super Close Projection System Product Overview Main Unit 4 6 Qlik 7 8 5 1 2. 3. 4. 5. 6. 7. 8. Control Panel Focus Ring Projection Lens Elevator Button Elevator Foot Power Socket Connection Ports IR Receivers 0 3M 2008. All Rights Resewed. Introduction 1 2 3 9

****** Page 15 ****** Introduction 10 3MTM Super Close Projection System Control Panel SCARCE RE.SYNC STANDBY 10 LAW 2 3 1 2. 3. 4. 5. 6. 7. 8. 9. Four Directional Select Keys Keystone +/- Enter Menu (On/Off) Source Select Re-Sync Power/Standby Power/Standby LED Lamp Indicator LED 10. Temp Indicator LED 0 3M 2008. All Rights Resewed.

****** Page 16 ****** 3MTM Super Close Projection System Connection Ports USB Video 8-V1d.o Introduction 7 15 9 10 11 Power Socket 12 13 1 2. 3. 4. 5. 6. 7. 8. 9. 5V-Relay Connector (Output: 5VDC, 2A 0—0-Æ) RS232 Connector Audio Input Connector (for S-Vjdeo or Composite) Audio Output Connector Audio Input Connector (for DVI-D or RGB1-ln or RGB2-ln) KensingtonTM Lock Port Networking Connector RJ45 USB Connector (connect to PC for Remote Mouse function) 10. Composite Video Input Connector 11. S-Vldeo Input Connector 12. Monitor Loop-through Output Connector 13. RGB2-ln Connector (PC Analog Signal/HD/Component Video Input) 14. RGB1-ln SCART Connector (PC Analog Signal/SCART RGB/HD/Component Video Input) 15. DVI-D Input Connector (PC Digital/HDTV/HDCP Input) 0 3M 2008. All Rights Resewed. 11

****** Page 17 ****** Introduction 12 3MTM Super Close Projection System Remote Control with Mouse Function 16 17 18 19 20 21 22 23 24 25 26 BLANK FREEZE DISPLAY MOOE MENU VGA2 CLEAR MUTE FORMAT O VIOEO 1 2 3 4 5 6 7 8 9 10 11 12 13 1. Power 2. Mute 3. Timer 4. Display Format 5. Mouse 6. Mouse Right Click 7. Page Up 8. Page Down 9. Four Directional Select Keys 10. Re-Sync 11. Enter 12. S-Vjdeo Source 13. Composite Video Source 14. DVI Source 15. Source Lock 16. Blank 17. Freeze 18. Display Mode 19. Mouse Left Click 20. Zoom In 21. Zoom Out 22. Clear 23. Menu 24. VGAI Source 25. VGA2 Source 26. Number Buttons 0 3M 2008. All Rights Resewed.

****** Page 18 ****** 3MTM Super Close Projection System Connecting the Projector Connect the Computer/Notebook 5VRelay Output Audio Output @ ‘ (For Active Speakers) Installation 3 3…………………………………………………….. 6……………………………………………. 8……………………………………………….. 5 4 6 VGA RS232 USB 7 DVI ……Power Cord . Audio Output Cable 0 3M 2008. All Rights Resewed. Network Cable (optional accessory) USB Cable RS232 Cable (optional accessory) VGA Cable DVI to DVI Cable (optional accessory) . Audio Input Cable (optional accessory) 13

****** Page 19 ****** Installation Connect the Video Audio Output (For Active Speakers) 3………………………………… 6………………. 14 3MTM Super Close Projection System Video Output 1 5 3 4 S-Vldeo Output 5 6 7 5V Relay Output 10 8 10 DVD Player7 Set-top Box, HDTV receiver . …Power Cord . Audio Output Cable . ….. Composite Video Cable (optional accessory) ….. …. S-Video Cable (optional accessory) 5…………………………………………………Audio Input Cable (optional accessory) VGA to 3 RCA Component/HDTV Adapter (optional accessory) …RCA Component Cable for YPbPr (optional accessory) VGA Cable HDMI to DVI Adapter (optional accessory) HDMI Cable (optional accessory) 0 3M 2008. All Rights Resewed.

****** Page 20 ****** 3MTM Super Close Projection System Powering On/Off the Projector Installation 1 2. 3. Test Pattern NOTE • Turn on the projector first and then the signal sources. Powering On the Projector Ensure that the power cord and signal cable are securely connected. The Power LED will turn red. Turn on the lamp by pressing “Power/Standby” button on the control panel O And the Power LED will turn blue. Turn on your source (computer, notebook, video player, etc.). The projector should automatically detect your source within “Management” menu; check that “Input Source” has been set to “Auto Searching”. To access the built-in test pattern, please press the “Blank” button, then up arrow. If you connect multiple sources at the same time, use the “Source” button on the control panel or direct source key on remote control to switch. 1 -SYNC POWER STANDBY o POWER 1 Power/Standby 0 3M 2008. All Rights Resewed. 15

****** Page 21 ****** Installation 16 1. 2. 3. 4. 3MTM Super Close Projection System Powering Off the Projector Press the “Power/Standby” button to turn off the projector lamp; you will see a message Wait 1 minute before you switch on next time. Press key again to confirm, Press key to remove this message. displayed on the projecor’s screen. Press the “Power/ Standby” button again to confirm. The cooling fans continue to operate for about 2 minutes for cooling cycle and the Power LED will flash red. When the Power LED stops flashing, the projector has entered standby mode. Once in standby mode, simply press “Power/Standby” button to restart the projector. Disconnect the power cord from the electrical outlet and the projector. Following a power off procedure, please allow 2 minutes before attempting to restart the projector. LED Indicator When the “TEMPT’ indicator turns red, it indicates the projector has overheated. The projector will automatically shut itself down. When the “LAMP” indicator turns red, it indicates a problem with the lamp. Turn off the projector and disconnect the power cord from the electrical outlet, then contact your local dealer or our service center. When the “LAMP” indicator flashes red, it indicates the fan has failed. Stop using the projector and disconnect the power cord from the electrical outlet, then contact your local dealer or our service center. 0 3M 2008. All Rights Resewed.

****** Page 22 ****** 3MTM Super Close Projection System Installation Adjusting the Projected Image Adjusting the Projector Image Height The projector is equipped with elevator feet for adjusting the image height. To raise the imaqe: 1. Press the elevator buttons O 2. Raise the image to the desired height angle e, then re- lease the button to lock the elevator feet into position. 3. Rotate the tilt adjusting foot O to fine-tune the display angle. To lower the image: 1. Press the elevator buttons. 2. Lower the image, then release the button to lock the elevator feet into position. 3. Rotate the tilt adjusting foot @ to fine-tune the display angle. Elevator Buttons C] 2 Elevator Feet 0 3M 2008. All Rights Resewed. 3 Tilt Adjusting Foot €0 2 Elevator Feet 17

****** Page 23 ****** Installation 18 3MTM Super Close Projection System Adjusting the Projector Focus To focus the image, rotate the focus ring until the image is clear. o Focus Ring 3M Super Close Projection System SCP715/ SCP717 Adjusting Projection Image Size The projector will focus at distances from 1.64 to 13.60 feet (0.5 to 4.1 meters). 000/ 36.2″ (91.9cm) 217.1″ (551.5cm) 144 7″ (367.6cm) 72.4″ (183.0m) 300.0″ (762.Ocm) 289 5″ (736.3cm) I-ld: Screen (Diagonal) Screen Size (WxH) Distance 3.28′(1.Om) 6.56′(2.Om) 9.84′(3.Om) 13.12′(4.Om) 2.17& 1.64′ (0.5m) 72.411838m) 147 1 4.34* (11.Ccm) 3.28′ (1.0m) 144 7i387&m) 6.56′ (2.0m) 13 03′ 9.84′ (3.0m) 13.12 (4.0m) 240.CCi180-ffT 6096x4572cm 18 OT 13.60′ (4.1m) This graph is for user’s reference only. 0 3M 2008. All Rights Resewed.

****** Page 24 ****** 3MTM Super Close Projection System Installation 3M Super Close Projection System SCP740 Adjusting Projection Image Size The projector will focus at distances from 1.64 to 16.40 feet (0.5 to 5.0 meters). 0 d 3 28′(1 .om) 6 56′(2.Om) 9 84′(3.Om) 13 12′(4.Om) 16 40′(5.Om) 33.7185±11) 1.64 (0.5m) 201.9″ (512 7cm) 134.6″ (341.8cm) 67.3″ (170.9cm) 336.4″ (854.5cm 269 1″ (683.6cm 4 Screen (Diagonal) Screen Size Distance (86.6cm) 67 5705′ x 35.85* 144 9 X 3.28′ (1 0m) x 71 32.80: 6.56′ (20m) 201.51512.7cm) 171.1′ x 1069T 9.84 (30m) 65 61′ (168.acml 13.12 (4.0m) 0 3M 2008. This graph is for user’s reference only. All Rights Resewed. 336.41854 16.40 (5.0m) 19

****** Page 25 ****** User Controls 3MTM Super Close Projection System Control Panel & Remote Control There are two ways for you to control the functions: Remote Control and Control Panel. Using the Control Panel MENU RE-s•næ Power/Standby Refer to the “Power On/Off the Projector” section Re-Sync Source Menu Four Directional Select Keys Enter Keystone 20 on pages 15-16. Automatically synchronize the projector to the input source. Press “Source” to select an input signal. Turn the menu On or Off. Use A V to navigate through the menus. Confirm your item selection. Adjust image distortion caused by tilting the pro- jector (±16 degrees). 0 3M 2008. All Rights Resewed.

****** Page 26 ****** 3MTM Super Close Projection System Using the Remote Control User Controls o 0 O O OO O 0 3M 2008. @ Power Mute Blank Timer Freeze Display Format Display Mode Mouse Control Mouse Right Click Mouse Left Click a Page Up e page Down Q Zoom In Zoom out Four Directional Select Keys Re-Sync All Rights Resewed. Refer to the “Power On/Off the Projector” section on pages 15-16. Momentarily turn off the audio. Press this button again to unlock. Momentarily turn off the video. Press this button again to unlock. Start the function of “Presentation Timer”. Press this button again to close. (see page 29) Press “Freeze” to pause the screen image. Press this button again to unlock. Display the “Aspect Ratio” section of the on- screen display menu to select the desired aspect ratio. Select the display mode from PC, Photo, Video, Cinema, sRGB and User. Use this button to navigate the mouse on the page. Mouse right click. Mouse left click. Use this button to page up. Use this button to page down. Zoom in to magnify the image. Zoom out to reduce the image. Use A V to navigate through the menus. Automatically synchronize the projector to the input source. 21

****** Page 27 ****** User Controls o o Menu Clear Enter Source Lock Video S-Video VGAI VGA2 DVI 22 3MTM Super Close Projection System Display or exit the on-screen display menus for projector. Clear your selection. Confirm your item selection. Select auto detection all connector ports or lock current connector port. Choose composite video source. Choose S-Video source. Choose RGB1-In or SCART source. Choose RGB2-ln source. Choose DVI-D source. 0 3M 2008. All Rights Resewed.

****** Page 28 ****** 3MTM Super Close Projection System On Screen Display Menus User Controls The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. 1. 2. 3. 4. 5. 6. Main Menu How to Operate To open the OSD menu, press “Menu” on the Remote Control or Control Panel. When OSD is displayed, use keys to select any item in the main menu. While making a selection on a particular page, press Y key to enter sub menu. Use A V keys to select the desired item and adjust the settings by key. Select the next item to be adjusted in the sub menu and adjust as described above. Press “Menu” to confirm, and the screen will return to the main menu. To exit, press “Menu” again. The OSD menu will close and the projector will automatically save the new settings. Information Management Heystone Eco Modo High Altitude Input Source Information Keypad Lock Reset Lamp Counter Reset Sub Menu IAN Setting 0 3M 2008. All Rights Resewed. Security 23

****** Page 29 ****** User Controls Information Management 24 3MTM Super Close Projection System Menu Tree-1/2 Service Center Source Format Frame Rate Dis la Mode Dis la Format Dis la Hours Lam Hours DMD Inside Tem rature Lan ua e Ke tone Eco Mode Hi h Altitude In ut Source Information Ke d Lock Reset Lam Counter Reset Auto Power Off Presentation Timer Mountin Rear Volume L o Ca ture RS232 Command Pro-ector ID Si nal Power On Direct Power On Eco. Standb English/ Franpis/ Deutschl Italiano/ Espanol/ Portugués/ (NR)/ a On/Off On/Off Auto Searching/ DVI/ VGAI/Ch•nponentI/ VG S-Video/ Video On/Off Yes/Cancel Yes/CanceI On/Off On/Off 3WUser Yes/CanceI RS232/RJ45 On/Off 3.7W/5.3W 0 3M 2008. All Rights Resewed.

****** Page 30 ****** 3MTM Super Close Projection System Image LAN Security 0 3M 2008. Menu Tree-2/2 Dis la Mode B htness Contrast Saturation Tint Gamma White Intens Dis la Format V. Shift 16:9 Sha ness F uen Phase H. Position V. Position DHCP IP Address Subnet Mask Gate Wa DNS Status Securi Enable Securi Timer Chan Secu Code All Rights Resewed. User Controls PC/ Photo/ Video/ Cinema/ sRGB’ User g ser Color Tem ture Gain Red Gain Green Gain Blue Offset Red Offset Green Offset Blue Gamma Red Gamma Green Gamma Blue Enhance Red Enhance Green Enhance Blue Enhance an Enhance Ma enta Enhance Yellow Auto/ 4 : 3/ 16 : 9/ Full/ Window/ Ltr. Box On/Off Yes/CanceI On/Off month/ da / hour 25

****** Page 31 ****** User Controls Ser Center Sour ce : Auto hrs 26 3MTM Super Close Projection System Information Wheel ; b ‘Segments Information To display the projector information on the screen. Service Center: To display the location of 3M world wide service centers. Service Center Source : +rame Hale • Mode : Omp Hows: Ouo H”‘ive Coior Segments Source: To display the input source information. Format: To display the resolution of projection image. Frame Rate: To display the frame rate of projection image. Display Mode: To display the present of image. Display Format: To display the aspect ratio of projection image. Display Hours: To display the projection time. Lamp Hours: To display the cumulative lamp operating time. DMD: To display the DMD native resolution. Color Wheel: To display the color wheel segments. Inside Temperature: To display the inside temperature of the projector machine. 0 3M 2008. All Rights Resewed.

****** Page 32 ****** 3MTM Super Close Projection System Mode High Souter Information Keypad Lock lamp Countel Reset can Language iir User Controls Management-1/3 Choose the multilingual OSD menu. Use the A or V key to select your preferred language. Management English Poi Press “Enter” to finalize the selection. Keystone Press the or to adjust image distortion vertically and make a squarer image. Eco Mode Choose “On” to use less brightness from the projector lamp, yet will make the projector lamp last longer. High Altitude Choose “On” to turn on High Altitude mode. Operate the fans at full speed continuously to allow for proper high altitude cooling of the projector. Input Source Enable input sources. Press into the sub menu and then use A or V to select. Press “Enter” to finalize the selection. The projector will not search inputs that are de-selected. 0 3M 2008. All Rights Resewed. 27

****** Page 33 ****** User Controls 28 Management Information 3MTM Super Close Projection System 5•Vi’Ieo Video On: Choose “On” to display source information on the screen. Off: Choose “Off’ to hide source information on the screen. Keypad Lock When the keypad lock function is on, the control panel will be locked, but the projector can still be operated by the remote control. If canceling this function, use the remote control or press the “Enter” key on the control panel for 7 seconds to turn it off. Reset Choose “Yes” to return the adjustments and settings to the factory default values. Management Mo•de Lwvk Reset Lamp Counter Reset Lamp Counter Reset Choose “Yes” to reset the lamp life hour counter after replacing the lamp. Management Lwvk Resel l. amp Counter Resel 0 3M 2008. All Rights Resewed.

****** Page 34 ****** 3MTM Super Close Projection System SéCOi ily Auto Timer Auto Power Off User Controls Management-2/3 Set the countdown timer interval. The countdown timer will start when there is no signal being sent to the projector. Then projector will automatically power off when the countdown has finished. (in minutes) Presentation Timer Set the countdown timer for presentation (in minutes). After setting the timer, press “Timer” button on the remote control to start the function. In the last minute, the timer will turn red. After the timer is finished, press “Timer” button on the remote control again to close the image. Mounting On: When you choose “On”, the projector turns the image upside down for ceiling-mounted projection. Off: The factory default setting. Rear On: When you choose “On”, the projector reverses the image so you can project from behind a translucent screen. Off: The factory default setting. 0 3M 2008. All Rights Resewed. 29

****** Page 35 ****** User Controls 30 3MTM Super Close Projection System Volume Press to decrease the volume. Press to increase the volume. Logo Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD menu, the new setting will take effect on next open. 3M: The default startup screen of 3M projector. User: Use memorize picture from “Logo Capture” function. Logo Capture Press “Yes” to immediately capture a picture what on the display screen. Piwe’ 011 Hear Volume Logo O tniti 0 3M 2008. All Rights Resewed.

****** Page 36 ****** 3MTM Super Close Projection System Management RS?3? Command Pwoiector ‘D Signal Vowel 00 RS232 Command User Controls Management-3/3 NOTE • When “Signal Power On” is enabled, Eco. Standby Mode will be auto set as 5.3W. NOTE • When “Eco. Standby” mode is enabled (3.7 W), the Signal Power On function is RS232: Allow RS232 control of an individual projector. RJ45: Allow network LAN via web browser (Internet Explorer) to control of projector. (Default setting) Projector ID ID definition can be set up by menu (range 01—99), and allow user control an individual projector by RS232. Refer to page 49 for the complete list of RS232 commands. Signal Power On On: The projector will automatically power on when plug in any signal source to the projector at standby mode. Off: Turn on the projector to normal mode. Direct Power On Choose “On” to turn on Direct Power On mode. The projector will automatically power on when AC power is supplied, without pressing the “Power/Standby” key on the projector control panel or “Power” key on the remote control. Eco. Standbv 3.7W: Save power dissipation further. 5.3W: Return to normal standby mode. disabled. 0 3M 2008. All Rights Resewed. 31

****** Page 37 ****** User Controls NOTE • “Saturation” functions is only supported under Video mode. 32 Image Oispla•,• Mode igl•l ness Contrast Display Mode 3MTM Super Close Projection System Image-1/2 There are many factory presets optimized for various types of images. PC: For computer or notebook. (brightest image) Photo: For optimum color at high brightness. Video: For playing video in a bright environment. sRGB: For standard PC color. (best color reproduction) User: Memorize user’s settings. Briqhtness Adjust the brightness of the image. Press the to darken image. Press the to lighten the image. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press the to decrease the contrast. Press the to increase the contrast. Saturation Adjust a video image from black and white to fully saturated color. Press the to decrease the amount of saturation in the image. Press the to increase the amount of saturation in the image. 0 3M 2008. All Rights Resewed.

****** Page 38 ****** 3MTM Super Close Projection System Tint Adjust the color balance of red and green. User Controls Press the to increase the amount of green in the image. Press the to increase the amount of red in the image. Gamma This unit comes with 4 preset gamma curves. After the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps to optimize your image output. White Intensity Use the white peaking control to set the white peaking level of DMD chip. 0 stands for minimal peaking, and 10 stands for maximum peaking. If you prefer a brighter image, adjust towards the maximum setting. For a smooth and more natural image, adjust towards the minimum setting. Color Color Temperature: Adjust the color temperature. At higher temperature, the screen looks colder; at lower temperature, the screen looks warmer. When you adjust the color setting item, the color temperature will be set as “User” automatically. And this set “User” is the same for all display mode. • Gain • Gaiti • Gteen • Otrset Blue • Gattvma Red • Gam•ma Green • Gan•vma mue • Enhance • Enhance Yellow Gain Red/ Gain Green/ Gain Blue: Adjust the contrast of the individual colors. Offset Red/ Offset Green/ Offset Blue: Adjust the brightness of 0 3M 2008. the individual colors. All Rights Resewed. 33

****** Page 39 ****** User Controls 34 3MTM Super Close Projection System Gamma Red/ Gamma Green/ Gamma Blue: Adjust the gamma curves of the individual colors. Enhance Red/ Enhance Green/ Enhance Blue/ Enhance Cyan/ Enhance Magenta/ Enhance Yellow: Adjust the advanced saturation adjustment of the individual colors. For example: _ Red Enhance Red + Red 0 3M 2008. All Rights Resewed.

****** Page 40 ****** 3MTM Super Close Projection System Image Display V. Shift Display Format User Controls Image-2/2 Use this function to choose your desired aspect ratio. Auto : Keep the image with original width-higth ratio and maxi- mize the image to fit native horizontal or vertical pixels. 4:3 : The input source will be scaled to fit the projection screen. 16:9 : The input source will be scaled to fit the width of the screen. Full : Resize image to fit full screen by width (1280 pixels) and height (800 pixels). Window: When a 4:3 image is bigger than a 16:9 screen, select the “Window” mode to fit the image onto the screen without changing the projection distance. Ltr. Box (LBX): This format is for non-16×9, letterbox source and for users who use external 16×9 lens to display 2.35:1 aspect ratio using full resolution. V. Shift (16:9) Adjust the image position up or down, when you select the aspect ratio of 16:9. Press the to move the image down. Press the to move the image up. Zoom Press the to reduce the size of an image. Press the to magnify an image on the projection screen. 0 3M 2008. All Rights Resewed. 35

****** Page 41 ****** User Controls NOTE • “Frequency”, Position” and “V Position” functions are only supported under Computer mode. 36 3MTM Super Close Projection System Sharpness Adjust the sharpness of the image. Press the to decrease the sharpness. Press the to increase the sharpness. Frequency “Frequency” changes the display data frequency to match the frequency of your computer’s graphic card. If you experience a vertical flickering bar, use this function to make an adjustment. Phase Change the display data frequency to match the frequency of your computer’s graphic card. When you experience a vertical flickering bar, use this function to make an adjustment. H Position (Horizontal Position) Press the to move the image left. Press the to move the image right. V Position (Vertical Position) Press the to move the image down. Press the to move the image up. 0 3M 2008. All Rights Resewed.

****** Page 42 ****** 3MTM Super Close Projection System OHCP Subnet Mas Way ONS DHCP User Controls LAN On: Assign an IP address to the projector from the DHCP server automatically. Off: Assign an IP address manually. IP Address Select an IP address. Subnet Mask Select subnet mask number. Gateway Select the default gateway of the network connected to the projector. DNS Select DNS number. Apply Press “Yes” to apply the selection. Status To display network information. 0 3M 2008. All Rights Resewed. 37

****** Page 43 ****** User Controls NOTE • When you used the projector IP address, you will 4. Open “Control Panel” to control your projector. 3MTM Super Close Projection System How to use web browser to control your projector 1. Fill in a new IP, a subnet mask, a gateway and a DNS in the dia- logue box. LAN DHCP Address Subnet M Ask Gate Woy ONS Status Disconnect 2. Then choose apply and press “Enter” button to effectuate the con- figuration process. 3. Open your web browser and type in from the OSD LAN screen then the web page will display as below: Setting Alert Setlinu not be able to link to your service server. 38 Welcome to the Projector Web Server 100.so.tcn Projector Control Panel V. Keystune It. Keystone He Source PIP Audio Corm •st Colour ‘Whitg Peaking C,OIOUf MOd* Manag ement Displ•y 700m V, Shift Projection 0 3M 2008. All Rights Resewed.

****** Page 44 ****** 3MTM Super Close Projection System For example: User Controls Use Microsoft Internet Explorer (IE) web browser to control the projec- tor, the IP address is 10.O.50.100. Step 1: Find an IP Address (10.0.50.100) from LAN function of projector. Step 2: Select apply and press “Enter” button to submit function or press “menu” key to exit. Step 3: To open Network Connections, click Start, click Control Panel, click Network and Internet Connections, and then click Network Connections. Click the connection you want to configure, and then, under Network Tasks click 0 3M 2008. Change settings of this connection. Step 4: On the General tab, under This connection uses the following items, click Inter- net Protocol (TCP/IP), and then click “Properties.” Step 5: Click Use the following IP address, and type in as below: 1) IP address: 10.0.50.XXX 2) Subnet mask: 255.255.0.0 3) Default gateway: 10.0.50.254 Step 6: To open Internet Options, click IE web browser, click Internet Options, click the Connections tab and click “LAN Settings.. All Rights Resewed. Local Area Connection Prop… Connea uung the f Ob5Wit’ig e AEGIS (IEEE 802 M.) C.a•trd’ Prote•td. c;mtocd grovtdoo ccornunjc.at:von newodss Internet Protocol TCP/IP Proper… You can cac•ab/ry you 10 fy sd.gi’lqs. 6′ Use lhefdowv•g ‘P ‘d&ew 10 2ss 10 O gateway C ONS Setuøv O-•ocse i’ cotmectcn. — kea LA’I do % O-oz•se dau o 234 54.0. 39

****** Page 45 ****** User Controls 40 3MTM Super Close Projection System Step 7: The Local Area Network (LAN) Setting dialog box appears, In the Proxy Server area, cancel the Use a proxy server for your LAN check box. , then click “0K” button twice. may Tb sever f” LAN tThese mt Step 8: Open your IE and type in the IP address of 10.0.50.100 in the URL then press “Enter” key. The web page will display as below: Welcome to the Projector Web Server F: Ionso.’Ø Projector Status Step 9: Open “Control Panel” to control your projector. 0 3M 2008. All Rights Resewed.

****** Page 46 ****** 3MTM Super Close Projection System IAN Security Security Enable Seg.•u.ilv Security Enable User Controls Security On: Choose “On” to enable security verification when turning on the projector. Off: Choose “Off’ to be able to switch on the projector without password verification. Security Timer The function can be selected the time (month/day/hour) to set the number of hours the projector can be used. Once this time has elapsed you will be requested to enter your password again. (Use number buttons on remote. To change password, follow change password security code.) Change Security Code • First Time: 1. Press the to set password. 2. The Password is 4 digits, DEFAULT VALUE is “0000”. (first time) 3. Use number buttons on the remote to select your password, and then press “Enter” key to confirm your selection. Security Enable Security Timer Change Security Code Enter Current Code Enter New Code Confirm Again 12 month 29 day 23 hour 0K 0 3M 2008. All Rights Resewed. 41

****** Page 47 ****** User Controls 42 3MTM Super Close Projection System Change Password: 1. Press “Enter” to input old password. 2. Use number button to enter current password, and then press “Enter” to confirm. 3. Enter new password (4 digits in length) using the number buttons on the remote, then press “Enter” to confirm. 4. Enter new password again and press “Enter” to confirm. 0 3M 2008. All Rights Resewed.

****** Page 48 ****** 3MTM Super Close Projection System Troubleshooting Appendices If you experience trouble with the projector, refer to the following information. Ifthe problem persists, please contact your local reseller or service center. Problem: No image appears on screen Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section. Ensure the pins of connectors are not crooked or broken. Check if the projection lamp has been securely installed. Please refer to the “Replacing the lamp” section. Make sure you have removed the lens cap and the projector is switched on. Ensure that the “Blank” feature is not turned on. Problem: Left of right edge of the image is missing or the image is unstable or noisy Press “Re-Sync” on the remote control or on control panel. If you are using a PC: For Windows 3.x: 1. In the Windows Program Manager, double click the “Windows Setup” icon in the Main group. 2. Verify that your display resolution setting is less than or equal to 1600 x 1200. For Windows 95 98 2000 XP: 1. From the “My Computer” icon, open the “Control Panel” folder, and double click the “Display” icon. 2. Select the “Settings” tab. 3. Click on the “Advanced Properties” button. If the projector is still not projecting the whole image, you will also need to change the monitor display you are using. Refer to the following steps. 4. Verify the resolution setting is less than or equal to 1600 x 1200 resolution. 0 3M 2008. All Rights Resewed. 43

****** Page 49 ****** Appendices 44 5. 6. 3MTM Super Close Projection System Select the “Change” button under the “Monitor” tab. Click on “Show all devices.” Next, select “Standard monitor types” under the SP box; choose the resolution mode you need under the “Models” box. If you are using a Notebook: First, follow the steps above to adjust resolution of the computer. 2. Press the toggle output settings. example: [Fn]+[F3] HP & Compaqe Dell Gateway Mac Apple: IBM NEC Toshiba System Preference*DisplaFArrangement4Mirror display If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector. Problem: The screen of the Notebook or PowerBook computer is not displaying a presentation If you are using a Notebook PC: Some Notebook PCs may deactivate their own screens when a second display device is in use. Each has a different way to be reactivated. Refer to your computer’s documentation for detailed information. Problem: Image is unstable or flickering Use “Phase” to correct it. (see page 36) Change the monitor colour setting on your computer. Problem: Image has vertical flickering bar Use “Frequency” to make an adjustment. (see page 36) Check and reconfigure the display mode of your graphic card to make it compatible with the product. 0 3M 2008. All Rights Resewed.

****** Page 50 ****** 3MTM Super Close Projection System Problem: Image is out of focus Adjust the Focus Ring on the projector lens. Appendices Make sure the projection screen. (see pages 18-19) Problem: The image is stretched when displaying 16:9 DVD The projector automatically detects 16:9 DVD and adjusts the aspect ratio by digitizing to full screen with 4:3 default setting. If the image is still stretched, you will also need to adjust the aspect ratio by referring to the following: Please select 4:3 aspect ratio type on your DVD player if you are playing a 16:9 DVD. If you cant select 4:3 aspect ratio type on your DVD player, please select 4:3 aspect ratio in the on screen menu. Problem: Image is reversed Select “Management-2/3 Mounting or Rear” from the OSD and adjust the projection direction. (see page 29) Problem: Lamp burns out or makes a popping sound When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the “Replacing the Lamp”. (see page 47) Problem: LED lighting message Power-LED NOTE • Steady light No light O Message Standby State (Plug in power cord) Warming Normal Mode Cooling Error (Lamp failed) Error (Fan failed) Error (Over Tempe) (Blue) o Flashing O O o o (Red) O O Flashing O o o Temp-LED o O O O O O 0 3M 2008. All Rights Resewed. Lamp-LED O O O O Flashing o 45

****** Page 51 ****** Appendices 46 3MTM Super Close Projection System Problem: Message Reminders Power Off: Wait 1 minute before you switch on next time. Press key again to confirm. Press key to remove this message. ENTER Replace the lamp: C)) Lamp life exceeded. 0 3M 2008. All Rights Resewed.

****** Page 52 ****** 3MTM Super Close Projection System Replacing the Lamp Appendices The projector keeps track of the lamp usage. It will show you a warning message: ! Lamp life exceeded. • Warning: Lamp compartment is hot! Allow 30 minutes to cool down before When you see this message, change the lamp as soon as changing lamp! possible. Make sure the projector has cooled down for at least 30 minutes before changing the lamp. 2 Lamp Replacement Procedure: • Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. 1. 2. 3. 4. 5. 6. 7. 8. Turn off the power by pressing the Power/Standby button. Allow the projector to cool down for at least 30 minutes. Disconnect the power cord. Use a screwdriver to unscrew the 2 screws from the cover.O Push up and remove the cover.e Use a screwdriver to unscrew the 2 screws from the lamp module.O Pull up the lamp handle carefully. O Remove the lamp module. O To replace the lamp module, reverse the previous steps. 0 3M 2008. All Rights Resewed. 47

****** Page 53 ****** Appendices NOTE • Remark : compressed computer image. 48 3MTM Super Close Projection System Compatibility Modes Mode VGA VGA VGA VGA VGA VGA VGA VGA VGA SVGA SVGA SVGA SVGA SVGA XGA XGA XGA XGA * SXGA * SXGA * SXGA * SXGA * SXGA * SXGA * SXGA+ * UXGA Mode MAC LC 13″ MAC II 13″ MAC 16″ MAC * MAC MAC G4 i MAC DV MAC DV MAC DV Resolution 640 x 350 640 x 350 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 720 x 400 720 x 400 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1152 x 864 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1400 x 1050 1600 x 1200 Resolution 640 x 480 640 x 480 832 x 624 1024 x 768 1152 x 870 640 x 480 1024 x 768 1152 x 870 1280 x 960 (ANALOG) VFrequency H.Frequency (DIGITAL) VFrequency I-I-Frequency (Hz) 70 85 85 60 72 75 85 70 85 56 60 72 75 85 60 70 75 85 70 75 85 60 75 85 60 60 (kHz) 315 37 q 37 q 315 37 q 375 43.3 315 37 q 35.2 37 q 48.1 46.9 53.7 484 565 60.0 68.7 63.8 675 77.1 63.98 79.98 91 1 63.98 75 (Hz) 70 85 85 60 72 75 85 70 85 56 60 72 75 85 60 70 75 85 70 75 85 60 75 85 60 60 (kHz) 315 37 -g 37 -g 315 37 -g 375 43.3 315 37 -g 35.2 37 -g 48.1 46_g 53.7 484 565 60.0 68.7 63.8 675 77.1 63.98 79.98 91 1 63.98 75 (ANALOG) VFrequency H.Frequency (DIGITAL) VFrequency I-I-Frequency (Hz) 66.66 66.68 74.55 75 75.06 60 75 75 60 (kHz) 34.98 35 49.725 60.24 68.68 31.35 60 68.49 60 0 3M 2008. (Hz) (kHz) All Rights Resewed.

****** Page 54 ****** 3 Nil TM Super Close Projection System RS232 Protocol Appendices Baud Parity: Nane Flaw Control : None SEND to projector 232 Cade IDoa1RIOO IDoa1R002 IDoa1ROOS IDoa1R007 IDoa1ROOS IDoa1R009 IDoa1R010 IDoa1R012 IDoa1R013 IDoa1R018 IDoa1R020 IDoa1R021 IDoa1R022 IDoa1R027 IDoa1R03C IDoa1R032 IDoa1R033 IDoa1R038 IDoa1R03S IDoa1R036 IDoa1R037 IDoa1R04S IDoa1R049 IDoa1ROSO IDoa1ROS1 IDoa1ROS2 IDoa1ROS3 IDoa1R062 IDoa1ROO IDoa1R071 IDoa1R072 IDoa1R077 IDoa1R07S IDoa1R079 Data Bits: S Stop Bits: I FIFO: Function Power ON OFF Fen Made On Fen Made Off Freeze Unfreeze Source lack Source lack off Mute On Mute Off Zoom plus Zoom mmus up ( Pan under zoom) dawn ( Pan under zoom) left ( Pan undar zcam) right ( Pan under mom) Function List 00=01-99, projector’: D, oa=J0 is far all projectors. i: a CarriageReturn cade : Ox13 Information On Information Off Source select Blank On Blank Off Display Format Color Temperature Loga Display Made Lago Capture Signal Power On Signal Power On High Altitude High Altitude Keypad L ock Keypad L ock Direct Pawer On Direct Pawer On F em Standby F em Standby Brightness Contrast Volume White Intensity Sharpness Phase V. Shift Proj ecter ID V. Keystone Auto Shutdown Presentation Tima: Saturation Gamma DVI VGAI VGA2 S -Video Video Full Winda w Ltr- Bax A uto Love User Photo Video Cinema User Off On Off On On Off on Off On Off on Off On Off Projector Return OR-CRY OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> OK.-CR> nnn=0J0-100 , osd show value 0—100. nnn=0J0-lJ0 , center is SO nnn=C00-C10 , center is nnn=C00-010 nnn=C01 nnn=C00 -063 nnn=C01 -099 nnn= —40 . COO 040 , nnn=0J0-l SO, unit i: I minutes nnn=C00-C03 , Gamma only has 4 line.. 0 3M 2008. All Rights Resewed. will set ver keystone value as +35 49

****** Page 55 ****** Appendices SEND from projector when got mvalid when standbyfwarmingicaoling,/aut of range R FA D from 232 Function Info ta web only D esenptlon 3MTM Super Close Projection System — standby warm-up f cooling out range bbbb LampHaur Projector Retum OKIdataJ .-Cu module Return rnaoTR03904 c : source dddd FW verE10n e : dry-play f status = range ( ! Caution data[] aze all ASIC character ) data[0] : data[l] : data[2] : data[3] : data[4] : data[-i] : data[6] : data[8] : data[9] : data[ll]: data[13] : data[14] : data[16] : data[17J : data[18J: data[2 J : data[23. 24] data[2-i „26] data[31.32] data[33. 341 • data[3S. 401 • data[41 data[44. 461 : data[47 49] Deseription Power Lamp lit Fen Mode Freeze Source Mute Blank High Altitude Keypad Lock Signal Pawer On Diret Power On F en Standby Source Display format Display Colcu: temperature Lago Mounting Rear Prajacta: D Volume Phase V,’hit2 Intensity Zoom Brightness Contrast V Position Ver. keystone Auto Power Off Sleep Time: 110=ou’aff 110=ou/aff 110=ou’aff Non-•DWVGAINGA21S-Vidac.Video Of I 110=ou’aff I “0=ou’aff xxx Projector SEND to nodule 232 Code IR23904n 50 Function alarm Inform Query Ian module Set Ian :naodule Set Ian module Reset Ian module n : 0/1/133/4.15: Normal•Tharmal Switch Error.•Fan LacWOver TamperatureLamp Hours Running Out•La.mp Fail n n-AAAAAAAANIQNNNNNGGGGGGGGDDDDDDDDPC A: IP Address N: Subnet Mask G: Gateway D: DNS P: DHCPM0de(O’1: C: FJ-4-i Connector State(0fl : Discanneetconnaet) n • —AAAAAAAAIQQNNNNNGGGGGGGGDDDDDDDD A: IP Address N: Subnat Mask G: Gateway D: DNS : IA’=DHCP 0 3M 2008. All Rights Resewed.

****** Page 56 ****** 3MTM Super Close Projection System RS232 Connector 3 O Appendices VGA-ln Connector 00000 00000 00000 00000 00000 2 Pin no. 1 2 3 Name TXD RXD GND 1 1/0 (From Projector Side OUT IN Pin no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 3M 2008. All Rights Resewed. Spec. NC GND GND GND GND DDC 5V HOT-DET NC DDC Data HS/CS vs DDC Clock 51

****** Page 57 ****** Appendices 52 3MTM Super Close Projection System Regulation & Safety notices This appendix lists the general notices of your Projector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the device and receiver • Connect the device into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/television technician for help. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Caution Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications Commission, to operate this computer. 0 3M 2008. All Rights Resewed.

****** Page 58 ****** 3MTM Super Close Projection System Operation conditions Appendices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 -this device may not cause harmful interference, and 2.this device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003. Remarque å l’intention des utilisateurs canadiens Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries • Electromagnetic Compatibility Directive 2004/108/EC Low Voltage Directive 2006/95/E Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it. 0 3M 2008. All Rights Resewed. 53


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

3M SCP740 (01) PDF MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.