Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** 3M Occupational Health & Environmental Safety Group 832 8310 EN 149:2001 FFPI NR D c€0086 8320 EN 149:2001 FFP2 NR D c € 0086 Fit Check Procedure For Valved Respirators: a) Cover the front of the respirator with both hands, being careful not to disturb the position of the respirator. 8833 3MTM 8300 Series Comfort Respirators Fitting Instructions 3M 8300 Series Comfort Respirators Respirator 8310 8312 8320 8322 8833 Type FFPI NR D FFPI NR D FFP2 NR D FFP2 NR D FFP3 R D APF 4 4 10 10 20 VALVE Standard: ENI 492001 + A12009 This respirator should not be used in oxygen deficient environments, for escape purposes or by people with beards/ facial hair or in atmospheres where concentrations of contaminant may exceed that deemed Immediately Dangerous to Life and Health (IDLH). lever thinkihg 3M Health & Safety Helpline Monday – Friday 9 to 5 10 IRELMD Occupational Health & Environmental Safety Group 1. 2. 3. 4. 5. Cup the respirator in your hand with the nosepiece at your fingertips allowing the headbands to hang freely below your hand. Position the respirator under your chin with the nosepiece up. Pull the top strap over your head resting it high at the top back of your head. Pull the bottom strap over your head and position it around the neck below the ears. Make sure that the straps are not twisted. Place the fingertips of both hands at the top of the metal nosepiece. Mould the nosepiece to the shape of your nose by pushing inward while moving your fingertips down both sides of the nosepiece. Pinching the nosepiece using one hand may result in less effective respirator performance. The seal of the respirator on the face should be fit checked prior to wearing in the work area. b) Inhale sharply. A negative pressure should be felt inside the respirator. If air leaks around the nose, readjust the noseclip as described in step 4 to eliminate leakage. Repeat the above fit check. If air leaks at the respirator edges, work the straps back along the sides of the head to eliminate leakage. Retest the seal. Repeat the procedure until the respirator fits properly. For Unvalved Respirators: a) Cover the front of the respirator with both hands, being careful not to disturb the position of the respirator. b) Exhale sharply. A positive pressure should be felt inside the respirator. If air leaks around the nose, readjust the noseclip as described in step 4 to eliminate leakage. Repeat the above fit check. If air leaks at the respirator edges, work the straps back along the sides of the head to eliminate leakage. Retest the seal. Repeat the procedure until the respirator fits properly. If you cannot achieve a proper fit, do not enter the contaminated area. See your supervisor. Note: Do not use with beards or other facial hair that may inhibit contact between the face and the edge of the respirator. 3M United Kingdom plc 3M Centre, Cain Road, Bracknell Berkshire RG12 Tel: 0870 60 800 60 3M.co.uk/ohes 3M Ireland Limited The Iveagh Building The Park Carrickmines Dublin 18 Tel: 1 800 320 500 Please recycle. Printed in UK. 0 3M 2009. All rights reserved. Fit Testing: The 3M 8300 Series Respirator is a tight fitting facepiece and therefore wearers require a fit test as per the COSHH regulations 2002. For qualitative testing FTI O and FT30 Fit Test Kits are available. CH8300FP V2 t ACCREDITED RPE Fit Test Provider
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL