XO XOIL42KSE (01) PDF Document

The light control for the XO XOIL42KSE uses the button with the light symbol. There are three illumination levels:

Press the button Once for HIGH illumination level.

Press the button Twice for MEDIUM illumination level.

Press the button Three times for LOW illumination level.

Press the button Four times for OFF.

Use BUTTON 0 to turn both the Blower and Lights On and Off on the XO XOIL42KSE.

The blower motor speeds for the XO XOIL42KSE are:

BUTTON 1: Blower motor operates on LOW speed.

BUTTON 2: Blower motor operates on MEDIUM speed.

BUTTON 3: Blower motor operates on HIGH speed.

To activate the POWER BOOST feature on the XO XOIL42KSE:

Press and Hold BUTTON 3 for 2 seconds.

This increases airflow to a fourth and even higher speed for 10 minutes. The button will blink while active.

To manually stop the POWER BOOST before 10 minutes has elapsed:

Press BUTTON 3 and it will revert to HIGH speed, or

Press BUTTON 0 to shut the blower off completely.

The POWER BOOST function will operate even when the hood is off.

To activate and deactivate the TIMER Function on the XO XOIL42KSE, press BUTTON T.

When BUTTON T is pressed (whether the blower is off or running), the motor will run at LOW speed for 5 minutes before shutting off the blower and lights automatically.

While the TIMER is activated, you can change speed or engage POWER BOOST, but the hood will still shut off after 5 minutes.

To manually turn the unit off before 5 minutes has elapsed, press BUTTON T or BUTTON 0.

To synchronize the optional remote control (XOVREMOTE1) with the XO XOIL42KSE hood, follow these simple steps:

1. Standing near the hood, while it is not running, press and hold BUTTON (Light symbol) on the hood for 4 seconds. The button should start to blink for 5 seconds.

2. When the button on the hood starts to blink, Press any button on the remote. The hood and remote are now synchronized.

3. If the synchronization fails for any reason, repeat steps 1 and 2.

To remove the baffles from the XO XOIL42KSE:

1. Pull down on the release latch.

2. Lower the front edge of the baffle.

3. Pull forward and remove.

To replace the baffles:

Insert the rear of the baffle, holding the latch open, swing the front up into place and release the latch.

Baffle filters should be cleaned at least once every 2 months, more frequently depending on the type of cooking performed and the build up of grease.

For cleaning the stainless steel on the XO XOIL42KSE:

Do not use corrosive detergents, abrasive detergents or oven cleaners.

Do not use any product containing chlorine bleach or any product containing chloride.

Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface.

Clean periodically with warm soapy water and clean cotton cloth or micro fiber cloth. Always rub in the direction of the stainless steel grain.

To remove heavier grease build up use a liquid degreaser detergent.

After cleaning use a non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain. Always rub lightly, with a clean cotton cloth or a micro fiber cloth and buff in the direction of the stainless steel grain.

Any painted surfaces should be cleaned with warm water and detergent only.

To replace the LED light module (XOPSPK6602) on the XO XOIL42KSE:

The LED light modules are held in place by spring clips which must be squeezed in before the lamp can be pushed down through the fascia.

Unplug the plastic molex connector.

Plug in the new fixture and snap back into place.

To reduce the risk of a range top grease fire when operating the XO XOIL42KSE:

Never leave surface units unattended at high settings. Heat oils slowly on low or medium settings.

Always turn hood ON when cooking with high heat.

Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

Use proper pan size. Always use cookware appropriate for the size of the surface element.

Keep fan, filters and grease laden surface clean.

Use high range setting on range only when necessary. Heat oil slowly on low to medium setting.

Do not leave range unattended when cooking.

Always use cookware and utensils appropriate for the type and amount of food being prepared.

To reduce the risk of injury to persons in the event of a range top grease fire on the XO XOIL42KSE:

SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

NEVER PICK UP A FLAMING PAN – You may be burned.

DO NOT USE WATER, including wet dishcloths or towels a violent steam explosion will result.

Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The fire is small and contained in the area where it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

General operational safety rules for the XO XOIL42KSE include:

Take care when using cleaning agents or detergents.

It is suitable for use in household cooking area.

Do not use this fan with any Solid-State Speed Control Device to reduce the risk of fire or electric shock.

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

Do not check filters with the hood working.

Do not touch the lamps after a prolonged use of the appliance.

No food must be cooked flambè underneath the hood.

The use of an unprotected flame is dangerous for the filters and could cause fires.

Watch constantly the fried food in order to avoid the cooking oil flares up.

Before performing any maintenance operation, disconnect the hood from the electrical service.

The rules to plan ductwork for the XO XOIL42KSE are:

This hood is designed to use an 8″ round duct; it may be transitioned to a 4″ x 14″ rectangular duct.

Never reduce duct size. Undersized ducting severely restricts air flow and harms performance.

Keep duct runs as short and straight as possible.

Avoid using flexible metal ducting if run is longer than 6′.

Never use plastic ducting.

Use smooth bore metal ducting.

Minimize the number of fittings.

When you must use fittings, try to separate them with sections of 4′ or more of straight duct.

Always follow the manufacturer’s guidelines for the cooking equipment you are venting.

If make up air control dampers are required, position the sensor in a straight run of duct ideally with 4′ of straight duct between each side of the sensor and a duct fitting. Remember to include power and control wiring for this in your plans.

Adhere to all local building codes and ordinances.

Use the worksheet to help calculate the Total Equivalent Feet of your duct run.

Total Equivalent Feet should be less than 100′.

The worksheet for estimating Total Equivalent Feet in a duct for the XO XOIL42KSE (for 1000 CFM or less) uses the following multipliers for components:

Note: If using flexible metal duct, increase all multipliers by 50% (e.g., 12 becomes 18).

The recommended mounting height above gas and electric cooktops for the XO XOIL42KSE range hood is 27″ to 32″.

It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazard; while hoods mounted too high will be hard to reach and will lose its performance and efficiency.

Before fitting the XO XOIL42KSE hood into the cabinet:

1. Remove the four (4) screws holding the side bracket (B) in place. Remove the brackets and set aside.

2. Remove the two (2) screws holding the bracket (H) in place and tilt down.

To fasten the XO XOIL42KSE hood in place:

Use four (4) screws along the inside front edge and four (4) screws in the back corners as shown.

The color convention for connecting the power supply wires to the junction box in the XO XOIL42KSE hood is:

BLACK = HOT LEG

WHITE = NEUTRAL

GREEN/YELLOW = GROUND

Polarity must be observed, and the unit must be properly grounded. Use a double throw disconnect switch.