WORX HYDROSHOT WG629E.9 (02) PDF Document

**Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts.

1. Pressure Setting Switch

2. Lock-Off Switch

3. Battery Pack Release Button

4. Battery Pack

5. On/Off Switch Lever

6. Hose Adaptor

7. Power Nozzle

8. Extension Lance

9. Short Lance

10. Nozzle Adaptor

11. Multi-Spray Nozzle

12. Hose Connector

13. Hose Filter

14. Hose Clip

15. Hose

16. Floater

17. Soap Bottle

18. Brush

19. Foldable Water Bucket

20. Carry Bag

Note: Not all the accessories illustrated or described are included in standard delivery.

The liquid must not be directed towards equipment containing electrical components.

Remove or disconnect the battery pack after use and before carrying out user maintenance on the appliance.

The appliance shall not be left unattended while it is connected to the battery pack.

The appliance is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.

Keep the appliance out of reach of children when it is energized.

Do not dismantle, open or shred cells or battery pack.

Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by conductive materials.

When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

Do not expose battery pack to heat or fire. Avoid storage in direct sunlight.

Do not subject battery pack to mechanical shock.

Keep battery pack clean and dry. Wipe the battery pack terminals with a clean dry cloth if they become dirty.

Battery pack needs to be charged before use. Always refer to the instructions and use the correct charging procedure.

Do not maintain battery pack on charge when not in use.

Battery pack gives its best performance when it is operated at normal room temperature (20°C ± 5°C).

This tool is intended for cleaning and watering.

When attaching the short lance to the power nozzle, align the two projections on the lance with the grooves of the power nozzle.

When attaching, rotate the nozzle left and right to make sure the nozzle is fully seated into position and gently pull it to make sure it is locked into position securely.

To use Working Mode 2 (Short lance used together with extension lance), attach the extension lance to the power nozzle, and then attach the short lance to the extension lance. When attaching, align the two projections on the lance with the grooves of the power nozzle.

Attach the hose to the power nozzle. After the hose is attached, check the connection by gently pulling upon the hose. It should not be pulled off.

Yes. Besides the hose supplied, you can also connect the power nozzle to your own water hose with suitable connectors. Remove the hose adaptor and attach the home garden hose with suitable connectors.

Note: When retightening the quick hose adapter, please tighten securely. Otherwise, it may not draw any water for proper operation.

Your power nozzle has two pressure modes. High pressure mode is suitable for removing strong stains, while low pressure mode applies to light duty and watering.

At the first use, you need to empty the air in the hose. Place the power nozzle below waist level (<1.5m/5ft) and set it at high pressure. Do not start working until the water goes up along the hose and sprays out. This could take up to 30 seconds or more depending on the fresh water source.

Choose a suitable nozzle pattern according to your work. Spray patterns 0°, 15°, 25° and 40° are applicable for cleaning, and the spray pattern with the symbol is best suitable for watering.

WARNING: Do not shift the nozzle pattern when the tool is powered on.

WARNING: Do not connect the machine to water supply which is turbid, muddy or corrosive.

For proper maintenance after using with sea water, the product should be rinsed by fresh water.

The soap bottle provides detergent suds for deeper cleaning of dirt. It is used in conjunction with the power nozzle or extension lance. Do not attempt to use cleaning without a lance or any accessories attached.

Remove the hose filter from the hose and get out the strainer. Rinse the parts with clean water before reassembling.

Inspect the product for damaged or worn parts before each use. Do not operate it if you find damaged or worn parts.

Before storage, completely drain all the water from the machine and hose.

Clean the moulded plastic housing of the machine using a soft brush and clean cloth. Do not use water, solvents or polishes.

Store in a secure and dry place out of the reach of children. Do not place other objects on the product.

Store the machine and the accessories in a frost free place.