VOX CGL6V17BL (01) PDF MANUAL

VOX CGL6V17BL (01) PDF SUMMARY:

How should the instruction manual be used?

Read the manual carefully before operation. Pictures in this manual are for reference only, the product in kind prevail.

---

To what does the instruction for Use apply?

The instructions for Use apply to several versions of this appliance. Accordingly, descriptions of individual features that do not apply to a specific appliance may be found.

---

What is the manufacturer not liable for?

The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.

---

What is the minimum distance between the supporting surface for cooking vessels on the hob and the lowest part of the range hood?

When the range hood is located above a gas appliance, this distance shall be at least 65 cm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account. The distance of 65 cm can be reduced for non-combustible parts of range hoods, and parts operating at safety extra low voltage, provided these parts do not give access to live parts if deformed.

---

What should be checked regarding the mains voltage?

Check that the mains voltage corresponds to that indicated on the rating plate fixed to the hood.

---

What should be checked for Class I appliances?

For Class I appliances, check that the domestic power supply guarantees adequate earthing.

---

How should the extractor be connected to the exhaust flue?

Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm. The route of the flue must be as short as possible.

---

Into what should the air not be discharged?

The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

---

What degree of aeration must be guaranteed if the extractor is used in conjunction with non-electrical appliances?

If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air.

---

When the cooker hood is used in conjunction with appliances supplied with energy other than electric, what is the maximum negative pressure allowed in the room?

When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.

---

What should be done if the supply cord is damaged?

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

---

What regulations must be fulfilled?

Regulations concerning the discharge of air have to be fulfilled.

---

For what purpose is the cooker hood intended?

The cooker hood is only for home use, not suitable for barbecue, roast shop and other commercial purposes.

---

For what purposes should the hood never be used?

Never use the hood for purposes other than for which it has been designed.

---

What should you never leave under the hood when it is in operation?

Never leave high naked flames under the hood when it is in operation.

---

How should the flame intensity be adjusted?

Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.

---

What is the requirement for deep fat fryers during use?

Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.

---

What should you not do under the range hood?

Do not flame under the range hood; risk of fire.

---

Who can use this appliance?

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

---

What should children be supervised to ensure?

Children should be supervised to ensure that they do not play with the appliance.

---

Who should not perform cleaning and user maintenance?

Cleaning and user maintenance shall not be made by children without supervision.

---

What caution should be taken when using cooking appliances?

“CAUTION: Accessible parts may become hot when used with cooking appliances”.

---

How often should the cooker hood and its filter be cleaned?

The cooker hood and its filter should be cleaned regularly according to the instruction.

---

What should be done before carrying out any maintenance work?

Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.

---

When should the filters be cleaned and/or replaced?

Clean and/or replace the Filters after the specified period (Fire hazard).

---

How should the hood be cleaned?

Clean the hood using a damp cloth and a neutral liquid detergent.

---

What is the maximum number of hob elements the appliance uses?

The appliance uses 4 hob elements at most.

---

What does the symbol on the packaging indicate?

The symbol on the packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

---

What does ensuring proper disposal of the product help prevent?

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

---

Who should be contacted for more detailed information about recycling this product?

For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

---

What are the initial steps for wall drilling and bracket fixing?

As a first step, proceed with the following drawings:

• Mark Points:
  • A vertical line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted.
  • The cooker hood should be placed 650-750 mm (horizontal line A) up from the cooking plane for safe and a good effect.
  • A horizontal line B at a minimum 800-900 mm above the cooker top.
  • A horizontal line C at a 272 mm above the B.
  • A horizontal line D at 470-790 mm above the cooker hood.

---

Where should points be marked on the horizontal lines?

• Mark a point (1) on the horizontal line D, 60 mm to the vertical reference line. Repeat this operation on the other side, checking that the three marks are leveled.
• Mark a point (2) on the horizontal line C, 60 mm to the vertical reference line. Repeat this operation on the other side, checking that the three marks are leveled.
• Mark a point (3) on the horizontal line B, 80 mm to the vertical reference line. Repeat this operation on the other side, checking that the three marks are leveled.

---

What are the connection options for the ducted version air exhaust system?

When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ɸ 150 or ɸ 120 mm, the choice of which is left to the installer.

---

What should be done if installing a ɸ 120 mm air exhaust connection?

If to install a ɸ 120 mm air exhaust connection, insert the reducer flange 3 on the hood body outlet.

---

How should the pipe be fixed in position?

Fix the pipe 4 in position using sufficient pipe clamps (not supplied).

---

What should be removed when installing the ducted version?

Remove possible charcoal filters.

---

How to fix the brackets?

• Chimney fixing bracket 9 with 2 screws 6 (ST5x50) supplied with the hood at the horizontal line D.
• Drill holes at the marked points with a 10 mm drill bit. Insert the Wall Plugs into the holes.
• Fix the Screws (5 x 50) bracket 6 with 2 screws supplied with the hood at the horizontal line B.

---

How to mount the hood on the wall?

• To mount on the wall, drill two 10mm. Insert two plastics wall plugs(supplied) into the holes.
• Insert two screws (ST5*50) 6 into the upper two plastic wall plugs, and tighten them leaving 3mm ,protruding from the Wall.
• Mount the hood on the top screws, Insert the bottom screws and fully tighten all the screws.
• Remove the filter from the inside of the hood body, fix the screws 6 to Wall Plugs 7 at the points (4).

---

How to hook the hood body?

Fix the exhaust pipe on the hood body. Connect chimney and hood body with 2 screws 8. Connect chimney fixing bracket 9 and chimney with 2 screws 8.

---

How to assemble the chimney?

• Insert the upper decorative chimney 2.2 into the lower decorative chimney 2.1 and drag it up to the horizontal line D.
• Connect upper decorative chimney 2.2 and chimney fixing bracket 9with 2 screws 8.

---

How to adjust the speed?

• ON/OFF LIGHTING SWITCH: Press on this switch to turn on the lights, and press again to turn them off.
• OFF MOTOR SWITCH: Press on this switch to stop the motor operation.
• SPEED SWITCH: Press on this switch, the motor runs at LOW speed.
• SPEED SWITCH: Press on this switch, the motor runs at MEDIUM speed.
• SPEED SWITCH: Press on this switch, the motor runs at HIGH speed.

---

How often should grease filters be cleaned?

The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.

---

How to clean metal self-supporting grease filters?

• Pull the comfort panels to open them.
• Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling downwards.
• Any kind of bending of the filters has to be avoided when washing them.
• Before fitting them again into the hood make sure that they are completely dry.
• (The color of the filter surface may change throughout the time but this has no influence to the filter efficiency).
• When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing outwards.

---

Are activated charcoal filters washable or regenerable?

These filters are not washable and cannot be regenerated.

---

How often should the activated charcoal filter be replaced?

The activated charcoal filter must be replaced approximately every 4 months of operation, or more frequently with heavy usage.

---

How to replace the activated charcoal filter?

• Remove the metal grease filters.
• Remove the saturated activated charcoal filter.
• Fit the new filters.
• Replace the metal grease filters.

---

What is the first step for light replacement?

Disconnect the power supply.

---

How to replace the light modules?

• Loosen Screw
• Take out the junction box
• Take out Led

---

What does the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE) require?

The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment.

---

What does the crossed out “wheeled bin” symbol on the product indicate?

The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.

---

Who should consumers contact for information concerning the correct disposal of their old appliance?

Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

---

What could be the cause if the light is on, but the motor does not work?

• The blades are blocked.
• The capacitor is damaged. Replace capacitor.
• The motor is damaged. Replace motor.
• The internal wiring of motor is cut off/ disconnected.

---

What should be checked if both the light and motor do not work?

• Light damaged. Replace lights.
• Power cord loose. Connect the wires as the electric diagram.

---

What should you do if an unpleasant smell is produced?

Replace motor.

---

What could be the cause of oil leakage?

Outlet and the air ventilation entrance are not tightly sealed.

---

What should be done to fix oil leakage?

Take down the outlet and seal with glue.

---

What could cause vibration?

• The blade, if damaged.
• The motor is not tightly fastened.
• The cooker hood is not tightly fixed.

---

What should be done to fix vibration?

• Replace the blade.
• Fasten the motor tightly.
• Fixed the cooker hood tightly.

---

What could cause insufficient suction?

• The distance between the cooker hood and the cooker top is too large.
• Too much ventilation from open doors or windows.

---

How can insufficient suction be resolved?

• Readjust the distance.
• Choose a new place to install the appliance or close some doors / windows.

---

What could cause the machine to incline?

• The fixing screws are not tight enough.
• The hanging screws are not tight enough.
• Check the blades.

---

How can you fix the machine inclining?

• Tighten the fixing screw and make it horizontal.
• Tighten the hanging screw and make it horizontal.