SMARTAB ST1009X (01) PDF Document

The following items are included with your SMARTAB ST1009X:

• 10.1″ tablet

• Keyboard

• Folio Case

• User guide

• Charger

• Micro USB cable

Please follow these care and safety precautions when using your SMARTAB ST1009X:

• During charging, keep your device and charger near room temperature for efficient battery charging.

• New batteries are not fully charged and may take more time to charge.

• The included charger is intended for indoor use only.

• Service should only be provided by an authorized service provider.

• Never attempt to disassemble, repair or modify the tablet yourself.

• Do not use the tablet in rain or other wet locations.

• Avoid spilling any liquid on the tablet.

• If the tablet gets wet, unplug all cables and turn off the tablet.

• Do not attempt to dry the tablet with an external heat source.

• Unplug all cables and turn off the tablet before cleaning.

• Use a soft, lint-free cloth to clean the tablet and display.

• Avoid getting moisture in open ports.

• Do not use household cleaners, solvents, alcohol, or abrasives to clean the tablet.

• Routinely check the tablet for proper and safe conditions. If there is any damage or broken parts, remove the tablet from use.

• If the screen is fractured or cracked, immediately remove this product from use and contact Customer Support.

• Cords could be a strangulation hazard. Keep out of reach of children under 3 years of age.

• Children pulling on the cord could cause equipment to fall. Adult supervision is required during use.

• When using headphones, it is recommended to listen at lower volumes for shorter periods. Long-term exposure to loud sounds at high volume may result in permanent hearing loss.

The specifications for the SMARTAB ST1009X are as follows:

• Display: 10.1″ IPS display (800 x 1280)

• Operating System: Android 6.0 Marshmallow

• Processor: 64-bit, Intel quad-core processor

• RAM: 1GB RAM

• Internal Storage: 32GB internal storage (Actual internal memory may vary)

• Expandable Storage: Micro SD card slot (expandable up to 64GB)

• Cameras: Front + rear cameras

• Connectivity: Wi-Fi 802.11 b/g/n, Bluetooth 4.0

To charge your SMARTAB ST1009X, connect the tablet to a wall outlet using the included power adaptor and Micro USB cable. When charging, a lightning indicator will appear in the battery icon on the screen.

• Turn off Wi-Fi when it’s not in use.

• Lock the tablet (turning the display off) to shorten charging time.

• To optimize battery time and performance, adjust the “Brightness” and “Screen timeout” options in the Settings panel.

• It is recommended to keep the brightness level at 50% or under if the tablet is in use while charging.

1. Press and hold the Power button until the startup screen appears.

2. Follow the initial setup wizard prompts on the screen.

3. To use the Google Play store, sign into or create a Google account when prompted. If you use Gmail, you already have a Google account.

• Power on the tablet: Press and hold the Power button until the startup screen appears.

• Power off the tablet: Press and hold the Power button until the “Power off” option appears on the screen, then select it.

• Lock the tablet (standby): Briefly press the Power button to turn off the screen and conserve the battery.

• Unlock the tablet: Briefly press the Power button, and then slide the “Lock icon” up.

If your SMARTAB ST1009X tablet malfunctions or freezes, you can use the reset button to restart it. Take a metal pin (such as the end of a paper clip) and gently push the recessed reset button on the side of the tablet. The tablet will restart.

Your SMARTAB ST1009X supports Micro SD cards up to 64GB.

• To install a Micro SD card: Carefully insert the card into the card slot until it clicks and locks into place.

• To remove a Micro SD card: Gently press the card inward to eject it.

To add a widget, press and hold anywhere on the home screen, and then select the “WIDGETS” option. Press and hold a widget from the list to place it on the home screen.

• Notifications panel: Swipe down from the top edge of the screen to display the Notifications panel. Here you can browse and reply to your emails, check software updates, reminders and more.

• Quick Settings panel: Swipe down twice from the top edge of the screen to expand and access the Quick Settings panel. Here you can easily enable or disable Wi-Fi, Bluetooth, Airplane mode and other settings.

To enable or disable Wi-Fi or Bluetooth, open the Quick Settings panel by swiping down twice from the top of the screen. Simply tap the icons for Wi-Fi or Bluetooth to turn them on or off. To access more settings options, select the gear icon.

You can show your SMARTAB ST1009X tablet’s screen on devices with Miracast Wireless display capabilities.

1. Turn on the Miracast feature on your Miracast supported TV or Miracast dongle (not included).

2. Connect your tablet to the same Wi-Fi network as your Miracast enabled TV.

3. Go to Settings > Display > Cast and tap on the menu icon.

4. Select “Enable wireless display”, then select the available display that will appear.

Note: Optimal video performance is achieved with videos that are 720p or under.

• To dock the tablet: Align the tablet and the keyboard, then slide the tablet into the dock. The tablet will automatically recognize the keyboard when docked properly.

• To undock the tablet: Firmly hold the keyboard, then gently pull the tablet upwards.

Yes, please note the following:

• The touchpad does not have a mechanical click. Tap the touchpad to select; do not push down on it.

• When the tablet is connected to the keyboard, you cannot use the USB port on the tablet.

• When the USB port of the tablet is being used, you cannot use the keyboard.