PHILIPS 65PUT6162 (03) PDF MANUAL

Read the safety instructions provided.

Always lift the TV with two people.

Handle the screen carefully to avoid damage.

Refer to the unpacking diagrams for your specific TV size (43″/49″/50″/55″ or 65″) as the process may differ slightly.

Take care not to drop the TV, especially when removing it from the packaging base for the 65″ model.

1. Place a soft protective covering on a flat, stable surface.

2. Carefully lay the TV screen-down onto the covering. Do not place the screen directly on the surface.

3. Attach the stand neck to the back of the TV.

4. Insert and tighten the four screws provided for the stand neck, ensuring they are correctly seated.

5. Attach the stand base to the stand neck.

6. Insert and tighten the two screws provided for the stand base, ensuring they are correctly seated.

7. With two people, carefully lift the TV holding the sides, avoiding pressure on the screen.

8. Place the TV upright on a stable, level surface.

1. After safely unpacking with two people, place a soft protective covering on a flat, stable surface.

2. Carefully lay the TV screen-down onto the covering. Do not place the screen directly on the surface.

3. Identify the left (L) and right (R) stand feet.

4. Attach the corresponding feet to the L and R slots on the back of the TV, ensuring they click into place correctly.

5. Insert and tighten the two screws provided for each foot (four screws total), ensuring they are correctly seated.

6. With two people, carefully lift the TV holding the sides, avoiding pressure on the screen.

7. Place the TV upright on a stable, level surface.

Connect the appropriate power cord (EU or UK) to the AC IN socket on the back of the TV and plug the other end into a wall power outlet.

Connect your coaxial antenna cable to the ‘TV ANTENNA’ 75 Ω input on the back of the TV.

Connect your coaxial satellite cable to the ‘[SAT]’ input on the back of the TV.

Insert a Conditional Access Module (CAM) into the COMMON INTERFACE slot on the side/back of the TV according to the provider’s instructions.

Connect an HDMI cable from the HDMI ARC output on your Home Theatre System to the ‘HDMI 1 (ARC)’ port on the TV. This allows audio from the TV to be sent back to the sound system.

Connect an Optical (Toslink) cable from the ‘DIGITAL AUDIO OUT – OPTICAL’ port on the TV to the optical input on your audio system.

Plug your headphones into the headphone jack (marked with a headphone symbol) on the side/back of the TV.

Connect your MHL device using an MHL cable to the ‘HDMI 3 / MHL’ port on the TV.

The TV can connect wirelessly to your home network router. Follow the on-screen network setup instructions.

Connect an Ethernet cable from your router to the ‘NETWORK’ port (Ethernet port) on the back of the TV.

Connect an HDMI cable from your computer’s HDMI output to any available HDMI input port on the TV.

Plug the USB flash drive into the ‘USB 2’ port on the TV.

Plug the USB hard drive into the ‘USB 1’ port on the TV. Ensure the hard drive receives adequate power if required.

Connect an HDMI cable from the player’s HDMI output to any available HDMI input port on the TV.

Connect the Y (Green), Pb (Blue), and Pr (Red) component video cables, along with the L (White) and R (Red) audio cables, from the player to the corresponding ‘Y/Pb/Pr, L/R’ inputs on the TV. Match the colors correctly.

Connect the CVBS (Yellow) video cable, along with the L (White) and R (Red) audio cables, from the player to the corresponding ‘CVBS, L/R’ inputs on the TV. Match the colors correctly. (Note: The Yellow CVBS input may share the Green Y input).

The VESA mounting patterns and screw sizes are as follows:

Size	Diagonal	VESA (x, y)	Screw Type
43″	(108 cm)	200×200 mm	M6
49″	(123 cm)	200×200 mm	M6
50″	(126 cm)	200×200 mm	M6
55″	(139 cm)	300×200 mm	M6
65″	(164 cm)	400×200 mm	M6

Use four M6 screws of the appropriate length for your wall mount bracket. Refer to your wall mount instructions for correct screw length.

Route cables neatly and use the provided cable management features or ties to secure them, ensuring they are not strained or pinched. The illustration shows routing cables through a clip or tie point on the back of the TV.

1. Slide the battery cover off the back of the remote control.

2. Insert two AAA (LR03) 1.5V batteries, making sure to match the + and – polarity markings inside the compartment.

3. Slide the battery cover back on until it clicks into place.

Point the remote control directly at the infrared (IR) sensor located on the front bottom edge of the TV. Ensure there are no obstructions between the remote and the sensor.

A joystick-like button is located on the back or bottom edge of the TV. Pressing it can turn the TV on or access a basic menu. Pushing the joystick up/down/left/right allows navigation for volume, channel, source selection, or menu control, depending on the context shown on the screen. Pressing the center (/OK) confirms selections.

Press the button associated with ‘Help’ on your remote control (indicated by a ‘?’ symbol or specific button) to access the on-screen Help menu.

For the full User Manual, visit philips.com/support or scan the QR code provided in the documentation. This will typically lead to a downloadable PDF version of the manual.