PETLIBRO AIR PLAF008 (01) PDF Document

The PETLIBRO AIR PLAF008 package includes the following items:

1 x Automatic Pet Feeder

1 x Stainless Steel Bowl

1 x Bowl Tray

1 x Quick Start Guide

1 x User Manual

1 x Power Adapter

1 x Power Cable

The main components of the PETLIBRO AIR PLAF008 are:

1. Lid Release Button

2. Lid

3. Desiccant Bag Holder Lid

4. Food Tank

5. Tank Base

6. Rotor

7. LCD Display

8. Buttons

9. Food Tank Lock

10. Control Panel Cover

11. Food Outlet

12. Stainless Steel Bowl

13. Bowl Tray

14. Power Cable Slot

15. USB-C Power Port

16. Battery Compartment

17. Non-slip Rubber Pad

18. Battery Compartment Cover

The LCD display of the PETLIBRO AIR PLAF008 shows the following information:

Battery status indicator: Lights up when batteries are installed. A blank battery status indicator means low battery level.

Rotor stuck indicator: Lights up when the rotor is stuck.

Low food indicator: Lights up when the food storage level is low.

Meal number: Displays the meal number being programmed (1-6).

Time or number of portions: Shows the current time or the number of portions for a scheduled meal.

AM/PM: Indicates whether the time is before noon (AM) or after noon (PM).

Follow these steps to set up your PETLIBRO AIR PLAF008:

1. Press the lid release button and remove the lid.

2. Add dry pet food to the food tank.

3. Replace the lid and press the lid release button to lock it.

4. Install the stainless steel bowl and bowl tray by attaching them to the front of the feeder base.

If you want to use a desiccant bag (not included) with your PETLIBRO AIR PLAF008, follow these steps:

1. Turn the desiccant bag holder lid (located on the underside of the main lid) counterclockwise to open it.

2. Place your desiccant bag (size: 35*20mm / 1.4*0.79in) into one of the desiccant bag holes.

3. Replace the holder lid and turn it clockwise to finish installing your desiccant bag.

The PETLIBRO AIR PLAF008 feeder supports dual power modes:

Using the power adapter and power cable: Connect the feeder to a wall outlet. It will automatically turn on, and the LCD display will light up in white.

Using battery power: Install three D alkaline batteries into the battery compartment on the bottom of the feeder. The feeder will automatically turn on.

Notes:

The LCD display will not stay on when using batteries or the power adapter.

A battery status indicator shows up in the display after installing batteries.

When the power adapter, power cable, and batteries are used at the same time, the feeder will only draw power via the power cable.

To power off the PETLIBRO AIR PLAF008, unplug the cable from the outlet. If it is in battery power mode, remove the batteries from the feeder.

1. After the feeder is powered on, press the top of the control panel cover to open it. Press the Set/OK button to enter time settings.

2. Press the Set/OK button again, and the hour digit will flash.

3. Press and hold the Up/Down button to set the hour, then press the Set/OK button to confirm.

4. Use the Up/Down button to set the minute and select from “AM” or “PM”.

5. Press the Set/OK button to confirm.

1. After setting the current time, press the Set/OK button to enter Meal 1 settings.

2. Press and hold the Up/Down button to set the hour and minute, select “AM” or “PM”, and set the number of portions.

3. Press the Set/OK button to confirm the Meal 1 settings.

4. Repeat steps 2 and 3 to set up Meals 2 through 6. If you want to set fewer than 6 meals, use the Up/Down button to select and customize a specific meal when one of the meal numbers flashes.

5. After setting up all desired meals, replace the cover and push it in to close.

Note: The maximum number of portions per meal is 16.

One portion is approximately 1/24 cup (10.4ml). The following table provides feeding recommendations:

When the PETLIBRO AIR PLAF008 feeder is powered on, press the Manual button once, and the feeder will dispense one portion of food. You can press the manual button up to five times consecutively, and the feeder will dispense five portions of food.

To reset the PETLIBRO AIR PLAF008 feeder to factory settings, press and hold the Up button and the Down button simultaneously for three seconds.

1. Pull the food tank locks on the sides of the base outwards.

2. Lift the food tank cover off the base.

3. Hold the tank base, turn the rotor clockwise, and lift the rotor out.

4. Clean and air-dry the rotor and food bowl.

Power off the device before cleaning.

Clean the food bowl with tap water.

Do not clean the feeder base in a dishwasher. Only the stainless steel bowl is dishwasher safe.

Use a soft damp cloth to clean the feeder base. Do not wash any part with electronic components.

Replace the desiccant bag every half a month to keep food fresh.

Blank battery status indicator on display: Please replace the batteries.

“LOWFOOD” indicator is on: Refill the food tank.

“STUCK” indicator is on: Disassemble the tank base and remove any food that’s stuck in the rotor.

Feeder is not dispensing food: Make sure you have filled the tank with enough food.

Feeder won’t turn on: Check if the power adapter, power cable, or batteries are correctly installed.

Food won’t come out:
– Please make sure the food in the tank is dry, and food size is within 2-15mm (0.07-0.6in) in diameter.
– Remove the food tank and tank base, and check if the chute inside is blocked.
– Check whether the battery level is low, whether the power adapter is connected, and whether a power outage occurs when the power adapter is connected but batteries are not installed.

Portion size is inconsistent: The first few portions may vary, but it doesn’t mean it’s faulty. After about 6 feedings, it should be almost even.

Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation. Keep them away from children and pets.

Do not use the feeder with pets that are not able to reach the food tray or with any physical disability.

Do not immerse the base part in water at any time as it may damage electronic components like the control panel.

Do not use the feeder outdoors. Check its operation frequently to be sure it is dispensing properly.

Do not use wet, canned or moist food.

Do not disassemble the feeder other than as instructed in this user manual.

Only use accessories recommended or sold by the manufacturer. The use of accessories not recommended or sold by the manufacturer may cause an unsafe condition.

Do not modify the pet feeder.

Examine the feeder after installation. Do not plug in if there is water on the power cable or plug.

To avoid tripping, always position the power cable out of the way of foot traffic.

Do not install or store the pet feeder where it will be exposed to weather or temperatures below 4°C (39.2°F).

Use D alkaline batteries to power the feeder. Do not use rechargeable batteries.

Check the batteries regularly. Before leaving for an extended period of time, always replace batteries with new ones.

Do not lift the pet feeder by the lid, food tank, or food bowl. Lift and carry it using both hands and the base, while keeping the feeder in an upright position.

Suitable for dry food only, with kibble sizes ranging from 2-15mm (0.07-0.6in) in diameter. Larger kibble may get stuck at the food outlet.

Do not put your fingers into the food outlet or let your fingers touch the rotor.

Power off the device when it’s not in use.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Radio frequency exposure statement: To maintain compliance with the FCC’s RF Exposure Guidelines, this equipment should be installed and operated with a minimum distance of 20cm from your body.