NZXT H1 (01) PDF DOCUMENT

1. Top Panel

2. Top Filter

3. Front Tempered Glass Panel

4. I/O Module

5. Side Panel

6. Side Filter

7. Rear Panel

8. PSU & AIO Radiator

9. AIO Pump

10. Chassis

11. GPU Riser Card

12. M.2 NVME Extension

13. 92mm Fan

14. 140mm Fan

15. 2.5” SSD Tray

16. M.2 NVME SSD Tray

A. 2.5mm Screws (x4)

B. Cable Tie (x5)

C. Power Cord

D. 6-32 Hex Screws (x8)

E. Intel Standoff 1200/115X Screws (x4)

F. Intel Standoff 1700 Screws (x4)

G. AMD Standoff TR4 Screws (x4)

H. Thumbnut with Spring (x4)

I. AMD Retention Bracket (x1)

J. Thumbscrews for AMD Retention (x2)

K. Breakout Cable (x1)

Clearances

Maximum GPU Clearance: 324mm

Maximum GPU Thickness: 58mm

Memory Height Clearance: 46mm

Specifications

Dimensions	W: 196mm H: 405mm D: 196mm
Material(s)	SGCC Steel and Tempered Glass
Weight	7.6 kg
Motherboard Support	Mini-ITX
CPU & Socket	Intel: Socket LGA 1700, 1200, 115X AMD: Socket AM4, TR4(Bracket not included)
Front I/O Ports	1x USB 3.2 Gen 2 Type-C 1x USB 3.2 Gen 1 Type-A 1x 4 Pole Headset Audio Jack
Filters	All air intakes
Included Accessories	750W SFX Gold Power Supply 140mm AIO Liquid Cooler 92mm PWM Fan PCIe 4.0 Extender Cable
Expansion Slots	2
Drive Bays	2.5″: 2
Radiator Support	1x 140mm (Integrated AIO)
Fan Support	1x 92mm Rear 1x 140mm on Radiator
Fan Specs (AER P140mm)	Speed: 500-1,800 + 300 RPM Airflow: 27.27-98.17 CFM Noise: 21-38dBA Fan Connector: 4-pin PWM
Fan Specs (RF-92RC1-B1)	Speed: 600-1800 + 10% RPM Airflow: 28.64CFM Noise: 23dBA Fan Connector: 4-pin PWM
Pump Specs	Speed: 4200 + 420 RPM Power: 12V DC, 0.35A Connector: 3-pin

1. Power Button / Power LED

2. USB 3.2 Gen 2 Type-C

3. USB 3.2 Gen 1 Type-A

4. Headset Audio Jack

Breakout Cable: This cable splits into Power SW, Power LED+, and Power LED- connectors for the motherboard’s F_PANEL header.

USB 3.2 Gen 1 Header: Connects the front panel Type-A port to the motherboard.

USB 3.2 Gen 2 Header: Connects the front panel Type-C port to the motherboard.

HD Audio: Connects the front panel headset audio jack to the motherboard.

1. Pull the top of the rear panel away from the chassis to release it.

2. Lift the rear panel up and away to remove it.

3. Pull the top of the front panel away from the chassis to release it.

4. Lift the front panel up and away to remove it.

5. Lift the top panel up and away to remove it.

6. Pull the side panels upwards to remove them.

1. Before installing the motherboard, remove the GPU riser card by unscrewing the two screws securing it to the chassis.

2. Carefully place the Mini-ITX motherboard into the chassis, aligning it with the four standoffs.

3. Secure the motherboard using the four 6-32 Hex screws provided in the accessory box.

1. Slide the expansion card (GPU) down into the PCIe slot on the GPU riser card.

2. Secure the expansion card to the chassis using the two 6-32 Hex screws.

1. Swing open the SSD tray door located on the motherboard side of the chassis.

2. Align the 2.5″ SSD with the tray and secure it using four 2.5mm screws.

3. Close the SSD tray door.

1. Open the backplate door on the rear of the chassis.

2. Place your motherboard’s backplate into the opening.

3. Close the door to secure the backplate in place.

1. For LGA 1700, ensure the standoffs are in the outermost position. For LGA 1200/115X, move the standoffs to the inner position.

2. Place the backplate onto the rear of the motherboard.

3. From the front of the motherboard, install the four Intel standoffs. Use the LGA 1700 standoffs (F) for socket 1700, or the LGA 1200/115X standoffs (E) for those sockets.

4. Place the pump with the pre-installed Intel retention bracket over the CPU.

5. Secure the pump using the four thumbnuts with springs (H).

1. First, prepare the retention bracket by removing the stock AMD retention clips from the motherboard.

2. Install the four AMD standoffs onto the motherboard.

3. Change the retention bracket on the water block from the Intel bracket to the AMD bracket (I).

4. Place the pump over the CPU.

5. Secure the pump using the four thumbnuts with springs (H).

1. Remove the four screws securing the plastic stock AMD retention clips.

2. Remove the plastic stock AMD retention clips from the motherboard, but keep the original AMD backplate in place.

1. Hold the pump and push the Intel retention bracket away from the pump.

2. Rotate the Intel retention bracket counter-clockwise to release it.

3. Pull the Intel retention bracket away from the pump.

4. To install the AMD bracket, place it over the pump head.

5. Align the tabs on the bracket with the grooves on the pump.

6. Push the AMD bracket down and twist it clockwise to lock it in place.

1. The fan controller is located next to the 92mm fan.

2. Connect the included micro-USB cable to the fan controller.

3. Connect the other end of the cable to an available internal USB 2.0 header on your motherboard.

Connect the 3-pin pump connector to a 4-pin CPU_FAN or AIO_PUMP header on the motherboard.

To ensure optimal performance, the tubes should be routed to the left side of the chassis, away from the GPU compartment.

AC Input Rating

Voltage	Current	Frequency
100-240Vac	10A-5A	50-60Hz

DC Output Rating

+3.3V	+5V	+12V	-12V	+5Vsb
20A	20A	62.5A	0.3A	3A
120W		750W	3.6W	15W
Total 750W

STEP 1: Connect all necessary cables to the motherboard, such as the 24-pin ATX power, 8-pin CPU power, and front panel I/O cables.

STEP 2: Connect the SATA and power cables to your 2.5″ SSD.

STEP 3: Connect the power cables to your GPU.

STEP 4: Re-install all panels in the reverse order of removal.

STEP 5: Connect the main power cord to the PSU.

CE Conformity
This product has been tested to be in compliance with all applicable EU council directives.

WEEE (Waste Electrical and Electronic Equipment)
This symbol indicates that this product should not be disposed of with your other household waste, but instead, hand them over to a designated collection point for the recycling of waste electrical and electronic equipment.

Safety Warning
To avoid risk of electric shock and damage to the equipment, please unplug the power cord from the power outlet before installing any component into the chassis.

To prevent any damage, please use anti-static wrist strap before handling any PC components.

If you choose to install third-party accessories, please check your user manual for the correct installation guideline.

Please do not insert your hands or any other objects into the fan when it is in operation.