NEFF T29TA79 (01) PDF Document

The suitable pan sizes for the NEFF T29TA79 gas hob burners are:

The following advice is intended to help you save energy and prevent pan damage on the NEFF T29TA79 gas hob:

• Use pans which are the right size for each burner.
• Do not use small pans on large burners. The flame must not touch the sides of the pan.
• Do not use damaged pans, which do not sit evenly on the hob. Pans may tip over.
• Only use pans with a thick, flat base.
• Do not cook without using a lid and make sure the lid is properly fitted. This wastes energy.
• Always centre the pan over the burner, not to one side. Otherwise it could tip over.
• Do not place large pans on the burners near the control knobs. These may be damaged by the very high temperatures.
• Place the pans on the pan supports, never directly on the burner.
• Make sure that the pan supports and burner caps are correctly positioned before using the appliance.

For dual-wok burners on the NEFF T29TA79 gas hob, the available power levels are as follows:

• Inner and outer flame on full power. (Setting 9)
• Outer flame on low power, inner flame on full power. (Setting 4)
• Inner flame on full power. (Setting 3)
• Inner flame on low power. (Setting 1)

If the gas supply on the NEFF T29TA79 gas hob is shut off by the intermediate valves, open the intermediate valves.

If there is a smell of gas in the kitchen when using the NEFF T29TA79 gas hob:

Step 1. Close the gas tap.

Step 2. Make sure that the gas cylinder has been connected correctly.

Step 3. If gas may be leaking, close the central tap in the gas line, ventilate the room and immediately call an authorised installer, who can inspect the gas system and issue an installation certificate. Do not use the appliance until you are sure that gas is not leaking from the system or the appliance.

Possible causes for an uneven burner flame on the NEFF T29TA79 gas hob are:

• The burner parts have not been fitted correctly.
• The burner slots are dirty.

The remedial actions are to fit the burner parts to the relative burner correctly and to clean the burner slots.

If the F1 or F2 symbol appears in the display while using automatic ignition on the NEFF T29TA79 gas hob, it indicates that the electronics have overheated. Switch the burners off or use only the lowest heat setting until the electronics have cooled down sufficiently.

To clean the NEFF T29TA79 gas hob once it is cool:

Step 1. Use a sponge to clean it with soap and water.

Step 2. After each use, clean the surface of the respective burner parts once they have cooled down. If any residue is left (baked-on food, drops of grease etc.), however little, it will become stuck to the surface and more difficult to remove later. The holes and grooves must be clean for the flame to ignite properly.

Step 3. Clean the burners and pan supports using soapy water and scrub with a non-wire brush.

Step 4. If the pan supports are fitted with rubber rests, ensure that these are also cleaned. The rests may come loose and the pan support may scratch the hob.

Step 5. Always dry the burners and pan supports completely. Water droplets or damp patches on the hob at the start of cooking may damage the enamel.

Step 6. After cleaning and drying the burners, make sure the burner caps are correctly positioned on the diffuser.

Caution must be exercised when cleaning the NEFF T29TA79 gas hob:

• Do not remove the control knobs when cleaning the appliance. The appliance may be damaged if moisture finds its way inside.
• Do not use steam cleaners. This could damage the hob.
• Never use abrasive products, steel scourers, sharp implements, knives, etc. to remove bits of hardened food from the hob.
• Do not use knives, scrapers or similar implements to clean the point where the glass meets the burner trims, the metal frames or the glass/aluminium panels, if fitted.

For maintenance on the NEFF T29TA79 gas hob:

Step 1. Always clean off any liquid as soon as it is spilt. This will prevent food remains from sticking to the hob surface and you will save yourself any unnecessary effort.

Step 2. Never slide pans across the glass surface, as you may scratch it. In addition, try not to drop heavy or sharp objects on the glass. Never strike any part of the hob.

Step 3. Grains of sand that may come from cleaning fruits and vegetables will scratch the glass surface.

Step 4. Melted sugar, or foods which contain a lot of sugar which may have spilt, should be cleaned off the hob immediately, using the glass scraper.

If the electrical operation of the NEFF T29TA79 gas hob is generally impaired, the possible cause is a defective circuit breaker, or the circuit breaker or one of the residual-current circuit breakers has been triggered.

The remedial action is to check inside the fuse box to see if any of the fuses are damaged and replace if necessary, or check the control panel to see if the automatic circuit breaker or a fault current switch has failed.

If the automatic ignition on the NEFF T29TA79 gas hob is not working, possible causes and remedial actions are:

If the automatic ignition on the NEFF T29TA79 gas hob is not working and the F1 or F2 symbol appears in the display, the possible cause is that the electronics have overheated. The remedial action is to switch the burners off or use only the lowest heat setting until the electronics have cooled down sufficiently.

If the burner on the NEFF T29TA79 gas hob switches off as soon as the control knob is released, the possible cause is that the control knob was not held down for long enough, or the burner slots are dirty. If the knob was not held long enough, hold the control knob down for a few seconds longer when switching on. If the burner slots are dirty, clean the burner slots.

If F3, F4, F5, F6, F7, F8, or F9 appear in the display of the NEFF T29TA79 gas hob, it indicates an electronics fault. Disconnect the hob from the power supply. Wait a few seconds and then reconnect it. If the indicator remains lit, contact the after-sales service.

If the heat setting indicator in the display of the NEFF T29TA79 gas hob continually deviates from the heat setting that was selected using the control knob, the issue is incorrect calibration of the electronics. The remedial action is to carry out the calibration in accordance with the installation instructions.