MEE H6D (01) PDF Document

The package for the MEE H6D includes the following items:

• H6D Bluetooth wireless headset

• Charging dock

• Micro-USB charging cable

The MEE H6D headset features the following components:

A. Volume down button

B. Status indicator light

C. Micro-USB charging port

D. Charging dock connector

E. Multifunction button

F. Volume up button

G. Microphone

The charging dock for the MEE H6D has the following components:

H. Headset dock connector

I. Power indicator light

J. Micro-USB power port

A low battery on the MEE H6D is indicated by a flashing red status indicator light and a “battery low” voice notification every five minutes.

The charging time for the MEE H6D is approximately 2 hours. The red status indicator light on the headset will turn blue once it is fully charged.

To charge your MEE H6D with the charging dock, follow these steps:

1. Connect the dock to any powered USB port using the included micro-USB cable. The red power indicator light on the charging dock will light up.

2. Place the headset on the charging dock.

You can directly connect the MEE H6D headset to any powered USB port using the included micro-USB cable to charge it.

Press and hold the Multifunction button for about 8 seconds until the status indicator light flashes red and blue. Note that the headset will enter pairing mode automatically on first use or after being reset.

1. Make sure the headset is in pairing mode (the status indicator light should be flashing red and blue).

2. Open the Bluetooth menu on the device you wish to pair (usually located in Settings->Bluetooth). If needed, select “search for devices”, “pair new device”, or “refresh.”

3. Select “MEE audio H6” from the list of available devices and allow the pairing to complete. Use “0000” if a PIN is required.

Note: It is only necessary to pair your headset once with each device.

The MEE H6D stores previously paired devices and reconnects automatically with the last paired Bluetooth device when powered on.

If the headset does not connect automatically, open the Bluetooth menu on your device and select “MEE audio H6” from the Bluetooth device list.

To wear the headset correctly, adjust the boom mic for use on either the left or right ear. Then, adjust the headband to a comfortable length.

• Power On: Hold for 2 seconds

• Power Off: Hold for 5 seconds

• Answer Incoming Call: Tap

• Reject Incoming Call: Hold for 2 seconds

• Hang Up: Tap

• Activate Siri® / Voice Command / Voice Dialing*: Hold for 2 seconds

• Redial*: Tap twice

• Play / Pause (during media playback**): Tap

*Not all devices support this functionality. For more information, refer to the user manual for your device.

**To start playing music, open a music app on your device and start playback.

• Decrease Volume: Tap

• Previous Track (during media playback): Hold for 2 seconds

• Increase Volume: Tap

• Next Track (during media playback): Hold for 2 seconds

Multipoint allows two Bluetooth devices to be connected to the headset simultaneously.

To use two Bluetooth devices with the H6D, first pair each one by following the pairing procedure, then power the headset off.

When powered on again, the headset will be able to connect to both devices. If one of the devices does not connect automatically, select “MEE audio H6” from the Bluetooth menu of the device.

To switch between the two connected devices, pause audio playback on the active device and start audio playback on the other connected device. It may take up to 30 seconds for the audio to switch.

Incoming calls will always take precedence over media. The H6D will automatically activate the connected device that has an incoming call.

To delete all previous Bluetooth pairings from memory, first power the headset on. Then, press and hold the Volume Up and Volume Down buttons at the same time for 5 seconds until the status indicator light flashes pink.

A new pairing will need to be created before the H6D can be used again.

• Clean with a soft cloth, damp with diluted soap water solution if necessary. Do not use chemical cleaners.

• Battery performance will be severely decreased when stored in extreme temperatures: below -10°C/14°F or above 45°C/113°F including direct sunlight.

• The lifetime of the battery will be significantly reduced if your headset is not charged for a long time. It is recommended to charge your headset at least once a month.

• Using headphones at high volumes for extended periods of time will result in permanent hearing damage. It is advised you keep volume levels moderate to low at all times for your safety. Turn the volume all the way down after connecting your headset, then gradually increase the volume until you reach a comfortable listening level.

• Keep the device and packaging out of reach of children.

• This device is designed and manufactured to operate within its defined design limits. Misuse may result in electric shock or fire.

• To prevent fire or shock hazards, do not expose this unit to rain or moisture. If the device comes in contact with liquids, quickly wipe away. If submersed in water, do not turn the device on until completely dried.

• There is a danger of explosion or fire if batteries are damaged. Keep away from direct sunlight, naked flames, flammable gasses, or heat sources such as radiators or stoves.

• There are no user replaceable/reparable parts in the headset. Disassembling it will void your warranty.

• Only use attachments/accessories specified by the manufacturer.

Dispose of this product in accordance with all local laws and regulations. Because this product contains electronic components and a battery, it must be disposed of separately from household waste. Contact local authorities to learn about disposal and recycling options.